Our offices will be closed on Tuesday, December 24 and Wednesday, December 25 for Christmas. We will be back on Thursday, December 26. Happy Holidays!
The KTM 990 adventure came to be in 2006 as the successor to KTM's 950 adventure and stayed in production until 2013. The 990 adventure has a DOHC 999cc 75* V-twin motor with 11.5:1 compression ratio mated to a 6 speed transmission. 105hp and 74lb-ft of torque. The dry weight is 461 lbs. and has a 34 inch seat height with a 19.5 L (5.2 gal) fuel capacity.
| Chain Size: | Front Sprocket: | Rear Sprocket: | Front Tire: | Rear Tire: | Spark Plug: |
| 525-118 | 17T | 42T | 90/90/21 | 150/70-18 | DCPR8E (Pre-'09) |
| 525-118 | 17T | 42T | 90/90/21 | 150/70-18 | LKAR8BI9 ('09-'13) |
This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.
Now available in the original version or the Ultra version. The original uses the front two emitters for low beam and then switches to the rear two emitters for high beam. The Ultra uses the front two emitters for low beam and then runs all 4 emitters on high beam at a reduced wattage. Wattage is 38 watts on low and 38 watts on high.
This bulb uses 4 Cree XHP 50 emitters, capable of more than 2500 lumens each. At 5000 lumens on each function, this is the brightest Cyclops H4 bulb.
*UNIVERSAL PART, PLEASE CHECK YOUR APPLICATION FOR FITMENT
Headlight is DOT approved. Has both high and low beams. Attaches to the upper fork tubes with rubber straps. Turn signals are embedded in the headlight housing.
Integrated turn signals may require resistors to flash correctly.
So you say you want more light for your dual sport? Give this 7"DOT legal Rally light a try and light it up like a freight train! HIGH/LOW operation and SAE/DOT/E4 approved.
This light does not have the large Cyclops logos shown on one of the images.
Optional 10.0 Lumen LED High/Low Upgrade and now the Phoenix LED complete headlight for the ultimate DOT headlight
The stock lamp that comes with this rally light is great, but you can get well over double the brightness with the LED upgrade at a substantially lower power draw. Note if your bike is ac powered at the headlight you will need the rectifier for the LED option.. AKA carbureted KTM's CRFX and XR400/650.. others may apply.
Each 10 watt Solstice Solo produces 900 lumens, which is roughly equal to a 50 watt halogen bulb. These are one of the brightest LED off road lamps on the market. The rugged and compact 2” x 2” square die-cast aluminum housing makes mounting easy. The Solstice Solo also features a 4 sided channel design that allows you to interlink it on all four sides with other Solstice Solo pods. Includes stainless steel mounting bracket and waterproof connection. Choose narrow, medium, wide or elliptical light beam pattern. Our favorite is the Elliptical pattern which is wide and flat, putting most of the light where you need it the most.
Sold each.
A game changer in auxiliary lights. High output, compact and lightweight!
The New Cyclops Aurora 2 inch lights rated at 4000 lumens combined. Using an authentic top binned Cree XHP50 emitter these lights pack a punch!
Available with or without the daytime Running light option (DRL) which can also be a front blinker. (you may need an LED flasher to do that)
Like all Cyclops lights we only use the Best Real Cree emitters. R113, R10 TUV and Emark certified IP68 rated.
Includes a full relayed wire harness designed for a Motorcycle. No need to use a switch if running the DRL version, also no need for a switch if using the skene dimmer or want the lights on in high beam and off in low beam. The factory switch will work for these applications. Unless you have a LED factory headlight in a R1200gs, 850Gs, or KTM1290 these bikes will require our Raider canbus controller.
Look at these quality features!
Available in two wattage configurations: 30 watts and 42 watts, which produce luminous outputs of 5000 lumens and 7000 lumens, respectively. If your motorcycle's electrical system cannot accommodate these wattages, the light can be operated in low beam mode, resulting in a 50% reduction in power consumption. When additional illumination is required, users can easily switch to high beam mode.
Despite its compact size, this LED light is designed to deliver substantial luminous output. Its performance surpasses that of other mini LED lights in the market.
The light is equipped with a durable push-button switch, metal handlebar mounts, and adaptable options that allow for compatibility with various motorcycle configurations. It features components such as switches, cords, strain reliefs, and optics that are engineered for enhanced water resistance, robustness, and overall performance.
Tailored specifically for snowbike applications, this light boasts a compact design with significant output capabilities. Enhanced heat is directed to the lens, facilitating snow melting and enabling continuous riding.
This light is ideal for users seeking a lightweight solution to comply with legal requirements for headlights while also being sufficiently powerful for racing and trail riding.
Installation is straightforward, with the light mounting easily to a number plate; however, the use of the recommended stainless steel platform mount is advised for improved convenience. The light operates using the motorcycle's battery power.
The Explorer light bar is equipped with a GoPro-compatible mount and an aluminum platform, allowing for versatile mounting options. A handlebar mount is provided for central positioning on the handlebars. (Fits all stock 7/8 and 1 1/8 bars. Not for flexbars) Notably, there are no plastic components in the light head assembly.
Included with the product is a rubber-covered switch that can be mounted on the handlebars, offering three power settings: off, 50%, and full brightness.
The light features a combo beam pattern, integrating spot, driving, and wide beam configurations into a single unit.
Now a lifetime warrantied LED light set at a budget friendly price.
The new Cyclops Pegasus led light set comes complete with a high quality relayed wire harness and a potent combo light beam pattern.
We are able to offer this fantastic light at a great price due to a one piece optic and sealed beam construction, eliminating extra parts and creating a very durable and high performance light.
These lights in white feature 7 watt emitters (28 watts per light) with two 10 degree and two 25 degree optics, Good for 500 plus ft of lighting (white).
The amber version is a Cree 3 watt emitters (12 watts per light).
This combo beam pattern offers good forward lighting and extremely good conspicuity.
The light set is available in white 5600K or a extremely bright Amber, perfect to allow those autos to see you. Lightweight and robust at 2.75 inches with a single stud mounting, they fit just about anywhere you would like to mount your lights.
Specs:
The Mojave Series LED Racing Lights have been designed to survive and operate in extreme conditions. Lights feature a heavy duty housing that can withstand hard impacts and a lens that is twice as thick as traditional lights. The light includes three different replaceable lens (Flood, Spot, and Combo).
Features:
This kit will work with the 6.6 Gallon Acerbis fuel tank for the DR650. You must run the light brackets inwards in order for there to be proper clearance with the 6.6. Gallon tank.
Kit includes:
This kit includes 2 auxiliary light mount brackets. These brackets are designed to mount to most lower triple clamps. New longer bolts are supplied to accommodate the thickness of the bracket. These brackets are powder coated black for a sleek and long lasting finish. The brackets can be used to put the addition of new lights to the outside of your forks or swap the brackets and the lights can be mounted inward to give more clearance for bigger shrouds or fuel tanks.
The perfect solution for mounting those LED auxiliary lights. The base of the RAM mount is held by your mirror. This puts the light where you can easily adjust the angle for different riding situations. This mount fits VisionX Solstice lights or any other light with a 6mm or 1/4" hole in the mounting bracket.
This is for Mount Only. Sold individually.
10 Watt LED lights sold separately.
This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.
Features:
This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.
Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.
License plate light with 5 LEDs. Compact and easy to mount. Meets plate illumination requirements with super white light.
This is for the LED license plate light ONLY.
License plate bolt with bright white LED light. The simple way to light up your plate.
Clear lens, amber LED type lights. Short flexible stems. Very small, only 2 7/8" long. Requires a LED turn signal flasher to flash properly. 4 Pack
Eight ultra-bright amber LED lights in a sleek design. Flexible stem helps absorb the occasional hit. Available in 2 pack or 4 pack
Recommended to use resistor for proper turn signal flash rate.
Specifications
Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.
White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.
Dazzling bright Amber blinker functions.
Everything comes in a spring-loaded stock designed to keep it safe from those unexpected tip-overs, crashes, or encounters with brush and trees. They’re flexible enough to bend 360 degrees, yet tough, durable, and almost impossible to break!
If you have a single indicator light for the blinkers that is not built into the display and is not LED you will need the diode kit (AKA DR650) If it is built into the speedo display it should not require the diode kit.
Available in a generic kit with Bullet connectors supplied. Great for your DR or almost any other bike with a single post blinker setup. These will work well on bikes that use a flasher, but you might have to add the female side of the connectors that are included in the kit.
Not for Yamaha T7, see model specific listing
These signals have short rubberized flexible stems and bright mini halogen bulbs.
The Barkbuster LED Indicator Lights for Jet, Storm & VPS Plastic Handguards to increase your visibility and safety using 15 high intensity LEDs that mount directly to the plastic handguard shells. Super bright auxiliary signals will make your directional intentions clear to upcoming traffic. The LED indicators are very low draw and E marked for road use.
Features:
What's in the box:
Please Note: Not compatible with the electrical system on the Honda Africa Twin CRF1000L
Ultra bright amber LED turnsignals offer nearly the same visibility as OEM in a much smaller package. 15 amber LEDs in every signal. Flexible rubber stalks. Requires a LED turn signal to flash properly.
Pack of Two
These Sequential Turn Signals are available in a 2 pack or 4 pack short stem with 7 LEDs.
Matte Black, plastic body with smoke lens and 8mm mount bolt.
Specifications
Triangle/Teardrop style signals with LEDs. Mounts on any flat surface to keep out of the way of brush, branches, and your exhaust system. Requires LED flasher or LED turn signal resistors to flash properly.
This Diode Kit is only necessary if you have a single dash indicator for your turn signals. One dash light for both left and right signals (such as on the DR650).
This kit allows power to flow in just one direction from the LED signals to the dash indicator light regardless of which direction you are signalling.
You may have noticed after adding aftermarket turn signals (especially LED units) that your blink rate has significantly increased. OEM flashers are designed for standard bulbs which draw a few watts each, much more than typical aftermarket bulbs or LED signals. This device is an effective alternative to using load resistors because it consumes considerably less watts, consumes less space, and does not generate excessive heat.
The plug is exactly the same as the OEM unit making swap outs a cinch. No wiring changes, cutting and adding connectors. Just plug it in and you will have a steady flash at the DOT OEM rate regardless of what signal bulbs you use. It is an all solid state design and will blink correctly with loads all the way down to 0.1W / 0.01A.
Not for any DRZ400 or Royal Enfield Himalayan
This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.
Not compatible with any DRZ400
Works on AC and DC lighting systems
Not compatible with any DRZ400
The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.
You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.
Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.
There are many options and configurations using this electronic tool.
No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.
Allows LED type turn signals (and low wattage flush mounts) to flash using a standard flasher unit. Connectors included. One kit works with 4 signals.
The Barkbusters 10 OHM Resistor Set for LED Indicator Lights will correct the flash rate of your auxiliary signal lights. Ready to plug in connectors make installation a breeze. These resistors are intended for Barkbusters LED Indicator Lights.
Features:
This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.
Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.
This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.
Fits Most Models
These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.
These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.
Replacement Halogen bulbs for mini style turn signals. Sold in a pack of 5 bulbs.
Roll-up pouch ideal for tucking away your lights when out on the trail.
Taillight and brake light Attaches to the top of the rear fender. Dimensions: 3 1/2" wide x 2" long x 3/4" tall. D.O.T. approved.
LED powered taillight, brake light, license plate light & license plate mount. Attaches to the underside of MX style rear fenders.
Taillight, brake light, & license plate holder (no plate light). Attaches to the underside of MX style rear fenders. Small and good looking!
Taillight, brake light, & license plate light. Attaches to the top side of enduro style (XR, KDX, etc) rear fenders. Dimensions: 2 3/4" x 4 3/4" x 2 1/2" tall. Wiring instructions included.
Taillight, brakelight, turnsignals, license plate light & license plate mount. Taillight is DOT approved, turn signals are not. Attaches to the underside of MX Style rear fenders. Turnsignals are embedded in the taillight housing. Wiring instructions included.
*Flushmount signals may require resistors to flash correctly
Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on 12-24 volt DC circuits.
Has both high and low beams. Attaches to the upper fork tubes with rubber straps. DOT and CE approved.
