Introduced in 2021, the CRF300L came with an abundance of changes with the biggest being; a new 286cc motor with a huge increase in torque, higher ground clearance (11.2 inches) and lighter weight overall compared to the CRF250L. Fuel capacity remained the same at 2.1 gallons.
| Chain Size: | Front Sprocket: | Rear Sprocket: | Front Tire: | Rear Tire: | Spark Plug: |
|---|---|---|---|---|---|
| 520x106 | 14T | 40T | 80/100-21 | 120/80-18 | SIMR8A9 |
Deltran quick-connect plug with LCD voltmeter display. Plug this into your Battery Tender, or any SAE cable, for an LCD display of the battery voltage. Three LED lights indicate the state of charge as well.
A digital voltmeter that can be mounted almost anywhere, on any bike, thanks to ProCycle's multi-position stainless steel bracket. Keeps you informed on the status of your charging system.
Completely waterproof and comes with connectors, wires and thorough instructions. A "must have" device for riders who use heated riding gear, heated grips, additional lighting, GPS, etc.
This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.
Now available in the original version or the Ultra version. The original uses the front two emitters for low beam and then switches to the rear two emitters for high beam. The Ultra uses the front two emitters for low beam and then runs all 4 emitters on high beam at a reduced wattage. Wattage is 38 watts on low and 38 watts on high.
This bulb uses 4 Cree XHP 50 emitters, capable of more than 2500 lumens each. At 5000 lumens on each function, this is the brightest Cyclops H4 bulb.
*UNIVERSAL PART, PLEASE CHECK YOUR APPLICATION FOR FITMENT
Headlight is DOT approved. Has both high and low beams. Attaches to the upper fork tubes with rubber straps. Turn signals are embedded in the headlight housing.
Integrated turn signals may require resistors to flash correctly.
So you say you want more light for your dual sport? Give this 7"DOT legal Rally light a try and light it up like a freight train! HIGH/LOW operation and SAE/DOT/E4 approved.
This light does not have the large Cyclops logos shown on one of the images.
Optional 10.0 Lumen LED High/Low Upgrade and now the Phoenix LED complete headlight for the ultimate DOT headlight
The stock lamp that comes with this rally light is great, but you can get well over double the brightness with the LED upgrade at a substantially lower power draw. Note if your bike is ac powered at the headlight you will need the rectifier for the LED option.. AKA carbureted KTM's CRFX and XR400/650.. others may apply.
Each 10 watt Solstice Solo produces 900 lumens, which is roughly equal to a 50 watt halogen bulb. These are one of the brightest LED off road lamps on the market. The rugged and compact 2” x 2” square die-cast aluminum housing makes mounting easy. The Solstice Solo also features a 4 sided channel design that allows you to interlink it on all four sides with other Solstice Solo pods. Includes stainless steel mounting bracket and waterproof connection. Choose narrow, medium, wide or elliptical light beam pattern. Our favorite is the Elliptical pattern which is wide and flat, putting most of the light where you need it the most.
Sold each.
A game changer in auxiliary lights. High output, compact and lightweight!
The New Cyclops Aurora 2 inch lights rated at 4000 lumens combined. Using an authentic top binned Cree XHP50 emitter these lights pack a punch!
Available with or without the daytime Running light option (DRL) which can also be a front blinker. (you may need an LED flasher to do that)
Like all Cyclops lights we only use the Best Real Cree emitters. R113, R10 TUV and Emark certified IP68 rated.
Includes a full relayed wire harness designed for a Motorcycle. No need to use a switch if running the DRL version, also no need for a switch if using the skene dimmer or want the lights on in high beam and off in low beam. The factory switch will work for these applications. Unless you have a LED factory headlight in a R1200gs, 850Gs, or KTM1290 these bikes will require our Raider canbus controller.
Look at these quality features!
Available in two wattage configurations: 30 watts and 42 watts, which produce luminous outputs of 5000 lumens and 7000 lumens, respectively. If your motorcycle's electrical system cannot accommodate these wattages, the light can be operated in low beam mode, resulting in a 50% reduction in power consumption. When additional illumination is required, users can easily switch to high beam mode.
Despite its compact size, this LED light is designed to deliver substantial luminous output. Its performance surpasses that of other mini LED lights in the market.
The light is equipped with a durable push-button switch, metal handlebar mounts, and adaptable options that allow for compatibility with various motorcycle configurations. It features components such as switches, cords, strain reliefs, and optics that are engineered for enhanced water resistance, robustness, and overall performance.
Tailored specifically for snowbike applications, this light boasts a compact design with significant output capabilities. Enhanced heat is directed to the lens, facilitating snow melting and enabling continuous riding.
This light is ideal for users seeking a lightweight solution to comply with legal requirements for headlights while also being sufficiently powerful for racing and trail riding.
Installation is straightforward, with the light mounting easily to a number plate; however, the use of the recommended stainless steel platform mount is advised for improved convenience. The light operates using the motorcycle's battery power.
The Explorer light bar is equipped with a GoPro-compatible mount and an aluminum platform, allowing for versatile mounting options. A handlebar mount is provided for central positioning on the handlebars. (Fits all stock 7/8 and 1 1/8 bars. Not for flexbars) Notably, there are no plastic components in the light head assembly.
Included with the product is a rubber-covered switch that can be mounted on the handlebars, offering three power settings: off, 50%, and full brightness.
The light features a combo beam pattern, integrating spot, driving, and wide beam configurations into a single unit.
Now a lifetime warrantied LED light set at a budget friendly price.
The new Cyclops Pegasus led light set comes complete with a high quality relayed wire harness and a potent combo light beam pattern.
We are able to offer this fantastic light at a great price due to a one piece optic and sealed beam construction, eliminating extra parts and creating a very durable and high performance light.
These lights in white feature 7 watt emitters (28 watts per light) with two 10 degree and two 25 degree optics, Good for 500 plus ft of lighting (white).
The amber version is a Cree 3 watt emitters (12 watts per light).
This combo beam pattern offers good forward lighting and extremely good conspicuity.
The light set is available in white 5600K or a extremely bright Amber, perfect to allow those autos to see you. Lightweight and robust at 2.75 inches with a single stud mounting, they fit just about anywhere you would like to mount your lights.
Specs:
The Mojave Series LED Racing Lights have been designed to survive and operate in extreme conditions. Lights feature a heavy duty housing that can withstand hard impacts and a lens that is twice as thick as traditional lights. The light includes three different replaceable lens (Flood, Spot, and Combo).
Features:
This kit will work with the 6.6 Gallon Acerbis fuel tank for the DR650. You must run the light brackets inwards in order for there to be proper clearance with the 6.6. Gallon tank.
Kit includes:
This kit includes 2 auxiliary light mount brackets. These brackets are designed to mount to most lower triple clamps. New longer bolts are supplied to accommodate the thickness of the bracket. These brackets are powder coated black for a sleek and long lasting finish. The brackets can be used to put the addition of new lights to the outside of your forks or swap the brackets and the lights can be mounted inward to give more clearance for bigger shrouds or fuel tanks.
The perfect solution for mounting those LED auxiliary lights. The base of the RAM mount is held by your mirror. This puts the light where you can easily adjust the angle for different riding situations. This mount fits VisionX Solstice lights or any other light with a 6mm or 1/4" hole in the mounting bracket.
This is for Mount Only. Sold individually.
10 Watt LED lights sold separately.
This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.
Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.
License plate light with 5 LEDs. Compact and easy to mount. Meets plate illumination requirements with super white light.
This is for the LED license plate light ONLY.
License plate bolt with bright white LED light. The simple way to light up your plate.
Clear lens, amber LED type lights. Short flexible stems. Very small, only 2 7/8" long. Requires a LED turn signal flasher to flash properly. 4 Pack
Eight ultra-bright amber LED lights in a sleek design. Flexible stem helps absorb the occasional hit. Available in 2 pack or 4 pack
Recommended to use resistor for proper turn signal flash rate.
Specifications
Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.
White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.
Dazzling bright Amber blinker functions.
Everything comes in a spring-loaded stock designed to keep it safe from those unexpected tip-overs, crashes, or encounters with brush and trees. They’re flexible enough to bend 360 degrees, yet tough, durable, and almost impossible to break!
If you have a single indicator light for the blinkers that is not built into the display and is not LED you will need the diode kit (AKA DR650) If it is built into the speedo display it should not require the diode kit.
Available in a generic kit with Bullet connectors supplied. Great for your DR or almost any other bike with a single post blinker setup. These will work well on bikes that use a flasher, but you might have to add the female side of the connectors that are included in the kit.
Not for Yamaha T7, see model specific listing
These signals have short rubberized flexible stems and bright mini halogen bulbs.
The Barkbuster LED Indicator Lights for Jet, Storm & VPS Plastic Handguards to increase your visibility and safety using 15 high intensity LEDs that mount directly to the plastic handguard shells. Super bright auxiliary signals will make your directional intentions clear to upcoming traffic. The LED indicators are very low draw and E marked for road use.
Features:
What's in the box:
Please Note: Not compatible with the electrical system on the Honda Africa Twin CRF1000L
Ultra bright amber LED turnsignals offer nearly the same visibility as OEM in a much smaller package. 15 amber LEDs in every signal. Flexible rubber stalks. Requires a LED turn signal to flash properly.
Pack of Two
These Sequential Turn Signals are available in a 2 pack or 4 pack short stem with 7 LEDs.
Matte Black, plastic body with smoke lens and 8mm mount bolt.
Specifications
Triangle/Teardrop style signals with LEDs. Mounts on any flat surface to keep out of the way of brush, branches, and your exhaust system. Requires LED flasher or LED turn signal resistors to flash properly.
This Diode Kit is only necessary if you have a single dash indicator for your turn signals. One dash light for both left and right signals (such as on the DR650).
This kit allows power to flow in just one direction from the LED signals to the dash indicator light regardless of which direction you are signalling.
You may have noticed after adding aftermarket turn signals (especially LED units) that your blink rate has significantly increased. OEM flashers are designed for standard bulbs which draw a few watts each, much more than typical aftermarket bulbs or LED signals. This device is an effective alternative to using load resistors because it consumes considerably less watts, consumes less space, and does not generate excessive heat.
The plug is exactly the same as the OEM unit making swap outs a cinch. No wiring changes, cutting and adding connectors. Just plug it in and you will have a steady flash at the DOT OEM rate regardless of what signal bulbs you use. It is an all solid state design and will blink correctly with loads all the way down to 0.1W / 0.01A.
Not for any DRZ400 or Royal Enfield Himalayan
This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.
Not compatible with any DRZ400
Works on AC and DC lighting systems
Not compatible with any DRZ400
Allows LED type turn signals (and low wattage flush mounts) to flash using a standard flasher unit. Connectors included. One kit works with 4 signals.
The Barkbusters 10 OHM Resistor Set for LED Indicator Lights will correct the flash rate of your auxiliary signal lights. Ready to plug in connectors make installation a breeze. These resistors are intended for Barkbusters LED Indicator Lights.
Features:
This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.
Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.
This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.
Fits Most Models
These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.
These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.
Replacement Halogen bulbs for mini style turn signals. Sold in a pack of 5 bulbs.
Roll-up pouch ideal for tucking away your lights when out on the trail.
Taillight and brake light Attaches to the top of the rear fender. Dimensions: 3 1/2" wide x 2" long x 3/4" tall. D.O.T. approved.
LED powered taillight, brake light, license plate light & license plate mount. Attaches to the underside of MX style rear fenders.
Taillight, brake light, & license plate holder (no plate light). Attaches to the underside of MX style rear fenders. Small and good looking!
Taillight, brake light, & license plate light. Attaches to the top side of enduro style (XR, KDX, etc) rear fenders. Dimensions: 2 3/4" x 4 3/4" x 2 1/2" tall. Wiring instructions included.
Taillight, brakelight, turnsignals, license plate light & license plate mount. Taillight is DOT approved, turn signals are not. Attaches to the underside of MX Style rear fenders. Turnsignals are embedded in the taillight housing. Wiring instructions included.
*Flushmount signals may require resistors to flash correctly
Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on 12-24 volt DC circuits.
Has both high and low beams. Attaches to the upper fork tubes with rubber straps. DOT and CE approved.
Inexpensive way of getting the factory look. Adds 1/2" of width to any standard foot peg. These will give you a much more stable platform when standing on the pegs.
Sold in pairs.
Not your average rubber insert! These rubber covers go over the top of your MK3 or MK4 Pivot Pegz so that the aggressive teeth are only exposed when you need them in muddy conditions.
Important to verify which style Pivot Pegz you have before ordering.
Replace those narrow heavy OEM foot pegs with the ZETA Racing aluminum foot pegs. When you are on your dirt bike a stable platform when riding is important. The aluminum foot pegs offer a wider platform and the spikes offer more traction for your foot preventing you from slipping. Over all it offers more control on your bike. Made from CNC machined A2014 forged aluminum and stainless pins.
Aftermarket foot pegs from our friends at Warp 9. Made from light weight T-6 aluminum and stainless steel teeth. These have an extra wide platform as well as the Exclusive "X" bridge that adds 2 center teeth for added grip.
50mm step width provides better grip and control
Services two Pivot Pegz and fits MK2, MK3 and MK4 Pivot Pegz
Kit Contents:
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.
This set of high quality replacement steering stem bearings includes:
High Quality chain. Will need to be cut to fit your sprocket combination.
All of these chains come with a clip type master link.
Always carry a spare master link when out on the trail.
Master links are not interchangeable. Be sure to check the manufacturer and series on your chain.
These do not fit the TW200 or XT250. Only for 520 os 525 chains, Please verify chain size.
JT Sprockets is the world's leading manufacturer of aftermarket sprockets, constantly raising the industry's standards for quality and service. JT Sprockets are the only sprocket manufacturer using the ultra-durable high carbon C49 steel for rear sprockets.
Two parts in one. Not just a cover over the countershaft sprocket, but also a case saver as well! Should you ever throw a chain, this will keep it from going into the engine cases and causing extensive and expensive damage.
Give your Honda the ultimate protection with B&B Off Road’s heavy-duty chain guard. This premium upgrade replaces the stock plastic guard, notorious for bending and breaking on tough terrain.
Crafted for Unrelenting Performance:
Precision-machined from robust 2.5mm marine-grade aluminium, this chain guard delivers unparalleled strength and durability. Say goodbye to worries about trail debris or rogue rocks damaging your chain – this guard stands strong against anything you throw at it.
Lightweight Design, Maximum Protection:
Despite its impressive strength, the chain guard is engineered to be lightweight, minimising any additional weight on your bike. This meticulous design ensures optimal performance without sacrificing protection.
A Perfect Fit:
This B&B Off Road chain guard seamlessly integrates with your Honda CRF, eliminating any installation hassles. The precise CNC machining guarantees a perfect fit for each compatible model.
Invest in Peace of Mind:
Protect your chain, a vital component of your motorcycle’s drivetrain. By preventing damage from debris and impacts, this chain guard minimises the risk of breakdowns and costly repairs. Hit the trails with confidence, knowing your CRF is shielded for the long haul.
Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.
Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.
The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!
Can break or rivet chains from #35 to #530 like a pro.
kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.
kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.
NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.
Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.
Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.
This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).
Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.
Maximum master link width 24.8mm.
Will not damage master links, hardened steel pins for reliable use.
Light weight billet aluminum construction.
A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.
Fits 520, 525, and 530 pitch chain.
ULTIMATE SPROCKET WRENCH KIT
Standard (OEM Diameter) Solid Mount Wave® Rotor
Every high-quality, Galfer-patented Wave® rotor is made from a proprietary mix of virgin high carbon 420 stainless steel, laser cut (never stamped), double disc-parallel ground to assure perfect parallel flatness and heat treated to each specific application. KBA and TUV approved. Seamlessly replaces stock rotor. Full instructions provided along with any technical help needed.
Motocross brake rotor featuring ultra lightweight radically profiled contours for great looks, great self cleaning and brake performance. Made with tough and durable heat treated stainless steel. Heat treated to perfection and then diamond ground to micron accurate surface finish and parallelism and will deliver great brakes that perform well and last.
Sintered Pads from EBC provide great performance in all conditions yet still give you long pad life. Front pads are double H rated for maximum breaking. Rear pads offer maximum durability and excellent braking performance.
This brake bleeder makes bleeding your brakes a one man job.
The unique check valve allows fluid and air to escape while preventing air from re-entering the system.
Combines wrench and bleeder valve into one convenient and compact tool
In stock form, the forks, featuring a single spring design are under sprung for any rider over 100 pounds. With limited travel, adding a stiffer spring in the right leg only per the stock design was not a viable option.
Race Tech instead offers a High Performance Spring Kit that adds a stiffer spring to the other fork. (The overall spring rate in the forks is the average spring rate between both legs.) This upgrade will make a drastic improvement in handling for most riders.
0.50KG/MM KIT
Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life.
Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material
Triple-lip seal design
Dyno-tested to last 3 to 4 times longer than OEM seals
Directional ribs allow seal to be installed easily
Kits include fork seals and dust wipers
Honda CRF3000L and Rally rear shock upgrade. The experts at Cogent Dynamics know suspension! A proven performance rear shock for your CRF300L or Rally for use under the most demanding conditions and on the roughest terrain worldwide.
Damping rates optimized to your specific needs, giving you the best ride comfort, traction and control. Frequency and velocity sensing valving works great over wide ranging conditions. Low internal friction. All CNC machined components for top quality and performance. Compact and rigid design with internal separator piston. Adjustable for spring preload and rebound damping. Fully serviceable shock is designed for the long haul.
*Spring color may vary due to specification requirement and availability.
Cogent Dynamics build a fully custom suspension component, just for you. To best meet your needs, please spend a few moments providing us with your riding style (off-road / adventure, or street / commuting) and your approximate weight with gear and luggage in the comments during checkout. The information you provide helps them setup your suspension to most closely meet your needs.
Kouba lowering link will lower the rear 1.75". Comes with bearings and seals installed for a quick and easy installation. Instructions included.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.
The three forces of suspension, testing procedures, even the black arts of chassis geometry: This explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.
Showa removed the schrader valve on many newer rear shocks. Now you need a needle to recharge your shock with nitrogen after a rebuild. Race Tech built this unit just for that job.
The features of this tool include 300 psi capacity, bleeder valve and T-handle plunger pin chuck. Swivel chuck has a 12" flexible hose. Comes complete with instructions, carrying box and Schrader valve extension (required on some Showa shocks). Nitrogen bottles available at any welding supply house.
Race, RS-4, Slip-On, Stainless Steel with Carbon Fiber End Cap
This Quiet Insert comes stock in all new FMF Q4 mufflers. If you lost yours, this is the replacement you need.
It will fit Q4, Q4 Hex, Powercore and Powercore Hex mufflers.
It will reduce the sound rating of the Power Core models, from about 99db down to about 96db.
Please choose the correct Insert for your muffler. If you are unsure of the year that your muffler was manufactured you can easily identify visually which insert you will need.
| Pre '21 | Installs using one small screw |
| '21-Cur | Installs using a spiral retaining ring |
Protect your head pipe from rock damage. This stainless steel spine clamps to your head pipe to add a layer of protective armor between your vulnerable pipe and those nasty rocks or logs. Fits the stock headpipe. Will fit the FMF head pipe with the addition of larger clamps.
This universal heat shield provides a great look at a great price.
If your aftermarket exhaust is missing heat shield mounting points, this is the easy fix you’ve been waiting for.
Includes one stainless steel mounting bracket with M6 threaded nut, and one stainless steel hose clamp.
Fits exhaust approximately 1.1inch-2inch diameter. Trimming may be required for smaller diameter exhausts.
Have you lost your stock heat shield, or need one on an aftermarket head pipe? FMF makes this nice unit that includes clamps, heat shield with the FMF logo and button head screws to hold it on. We recommend Anti-Seize on all exhaust fasteners.
Don't get burned! Giant Loop's ingeniously simple and effective exhaust shield protects bags and bodywork from heat damage. The Hot Springs Heat Shield helps avoid the meltdown, preventing bags and side panels from touching your bike's exhaust. It's the lightweight, universal heat problem-solver for virtually any motorcycle exhaust system. Backed by a Limited Lifetime Warranty.
The Chilly Exhaust Heat Shield is the most effective heat shield on the market. The innovative three piece design consists of a top shield attached to 2 rails with rivets and spacers. This reduces the contact area and slows down heat transfer. They have incorporated a patented, insulated reflective blanket on the underside of the shield to reduce radiant heat transfer. The included stainless steel clamp makes it simple to install.
We highly recommend a heat shield if you run soft luggage without hard racks.
FEATURES:
DIMENSIONS:
The latest in muffler packing technology. Spec 31 high performance muffler packing resists breakdown up to 1400°F, is universal, and is easy to install.
Re-pack your silencer with this pro-quality, three layer packing system and restore lost power and sound control.
Kit includes:
A highly refined blend of aluminum, copper and graphite lubricants. Use during assembly to prevent galling, corrosion and seizing due to weathering or chemicals. Anti-Seize assures easier disassembly. Temperature range: -60°F to 1600°F (-50°C to 870°C). Salt, corrosion and moisture resistant – ideal for marine use. Meets Mil Spec #907E.
Replacement Exhaust Pipe Retention Spring
