Search Products

Eagle Manufacturing balancer lever kit, featuring top-quality components.

The Eagle Manufacturing idle-shaft lever and spring is designed to replace the less durable stock unit. The one-piece lever is precision machined from 17-4PH hardened stainless steel, ensuring exceptional strength. The kit also includes a stainless doohickey and a torsion spring with a drill bit, replacing the previous extension springs with a superior torsion spring for enhanced durability.

A direct replacement for the stock KLR hoses that tend to crack and leak after a few years.

These silicone hoses are custom made for us. Silicon hoses operate at much higher temperatures and pressures than other rubbers, they don't perish, and they look great!

Our very own version of the popular thermostat bypass for the KLR. Gives faster warm up and more constant engine temperatures. Eliminates the wildly fluctuating engine temperature gauge. A more controlled and constant temperature is easier on your piston and cylinder and may prevent or reduce oil consumption. We use a 180 degree thermostat instead of the stock (too cold!) 160 degree unit. Warmer coolant temperature promotes better fuel vaporization and can increase fuel economy.

Our bypass system mounts the new thermostat in a small billet extension housing right where the stock thermostat is now. There is no bulky external housing to hang off the motor. The bypass hose tees in to the lower radiator hose using a length of quality high temperature silicone hose. It all makes for a clean simple installation.

The complete Thermo Control package - Our in-house designed Thermostat Bypass kit, a set of Custom Silicone Hoses and a Hi-Pressure Radiator Cap. All combined to help your KLR cooling system be at the top of its game. The Thermostat Bypass kit includes a thermostat with a higher temperature rating that will keep the motor more in its happy spot.

The Silicone hoses are stronger than the stock rubber units and will better resist cracking and leaking.

The Neutral Sending Unit "NSU" on the DR650 can be a problem. The factory screws tend to loosen over time. You really would not want them to get loose in your motor! The permanent solution is to safety wire them. We looked high and low and finally found pre-drilled screws in the correct length and thread pitch. Here we offer a complete kit to take care of those pesky screws.

If you don't do this, you don't have a screw loose, you have TWO screws loose!

Kit Contents:

• 2 drilled stainless steel screws
• Plenty of safety wire
• Wire twisting tool
• New lock tab for the clutch hub
• New clutch cover gasket

Generator cover gasket to seal up the cover once you have your new Doohickey in place. New OEM gasket. What else can we say? If in doubt, put in a new one.

A Suzuki OEM gasket for the Cam Chain Tensioner. You are going to need it if you work on your starter motor. It is not a good idea to re-use this gasket. If it blows out, it will dump a large amount of oil onto your right foot.

Genuine Suzuki replacement gaskets.

Complete gasket kit includes all gaskets and oil seals necessary for rebuilding your engine.

This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug in the standard kit, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

Providing unbeatable performance and exceptional value, Hi-Flo Filter is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

Grab our 5-pack and save both time and money!

Providing unbeatable performance and exceptional value, Hi-Flo is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

You pay $3.79 per filter with our value 5-pack!

• Cleanable and reusable filter
• 35 micron stainless steel mesh
• Stainless check ball and stainless spring
• CNC aluminum caps front and rear

Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

Grab our 5-pack and save both time and money!

K&L® shims exceed the maximum of the Apparent Rockwell Hardness "C" scale. Shims average 47.0 compared to the 46.0 maximum.

This kit fits KLR650 87-18 as well as other brands and models , please verify correct size for your model before purchase.

A pair of stage 2 intake and exhaust 'drop-in' camshafts. Great mid-range and top-end increase. Uses stock valve springs. Modifying the airbox and rejetting will be required to realize power improvements with these cams. These are new billet cams - No core return required!

Since 1948, Barnett clutch plates and springs have been made from the finest materials available.

• 6 Kevlar friction plates
• 5 Steel drive plates
• Clutch springs
• Clutch cover gasket

• Complete set of friction plates, steel plates, and springs
• Heavy-duty springs help prevent clutch slip
• Restores proper stack height, fixes clutch slip caused by wear and tear

Wiseco 96mm/+1.00 mm piston with rings, wrist pin, circlips, head gasket, and base gasket. 

Requires your cylinder to be bored to fit the larger piston.

All Wiseco Pistons are forged from high silicon, low expansion aluminum which offers superior strength, reduced weight, improved heat transfer, and longer life.

Diamond turned finish from one of the many CNC computer controlled turning centers guarantees you a perfect finish with no size variation. Wiseco pistons can be installed in any of today’s cylinder bore compositions

Wiseco’s state-of-the-art computerized manufacturing facility is dedicated to supplying both the high-perfomance racer and recreational enthusiast with the finest forged piston available in today’s market place.

Includes forged Wiseco 83mm Piston (83.00/+4.00 10.5:1), Rings, Clips, Pin.

• All Wiseco Pistons are forged from high silicon, low expansion aluminum which offers superior strength, reduced weight, improved heat transfer, and longer life.
• Diamond turned finish from one of the many CNC computer controlled turning centers guarantees you a perfect finish with no size variation. Wiseco pistons can be installed in any of today’s cylinder bore compositions
• Wiseco’s state-of-the-art computerized manufacturing facility is dedicated to supplying both the high-perfomance racer and recreational enthusiast with the finest forged piston available in today’s market place.

 Top end gasket set.

• Raises compression for better low end power.
• Graphite gaskets feature a steel core, laminated on both sides with flexible graphite.
• Fiber gaskets designed for maximum seal, flexibility and torque retention.
• O-ring gaskets meet or exceed oem specifications.

Sintered Pads from EBC provide great performance in all conditions yet still give you long pad life. Front pads are double H rated for maximum breaking. Rear shoes offer maximum durability and excellent braking performance.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads.

Always wanted to build or true your own wheels? Maybe just be able to balance your wheels after changing tires. This stand is perfect for both of those tasks.

• Features a bubble level to balance wheels correctly the first time
• Steel plate construction for durability and stability
• Comes with shaft, cones and spacers to fit just about any wheel

Steel wheel weights replace the old lead ones that are no longer legal in some states. Mount up new tires and make sure they are balanced for a smoother ride and longer tire life.

This is a 60 piece pack, 1/4 oz. weights with adhesive backing.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

• Made from 4mm thick aircraft aluminum
• Oil drain hole for easy access
• All mounting hardware included

This gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now and avoid having an exhaust leak after you install your new exhaust.

This gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers do not require a joint gasket but all other aftermarket mufflers as well as the stock muffler require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.

Order up your new levers here! If you keep breaking levers, you might want to think about a set of hand guards to protect them in case of a fall.  

These are genuine factory Yamaha replacements.

• Machined and knurled 6061 billet aluminum. Actual color may vary
• Removable end cap for easy hand guard installation
• Works with standard housing

Ease the pressure on your wrist during those long highway drones out to where the fun begins. ProCycle has developed this kit that includes a Vista-Cruise throttle lock, a specially modified alloy throttle tube and an anchor plate that attaches to your throttle housing. Just flip the thumb lever down to apply enough friction to hold the throttle in place. Use the supplied longer screw to attach the anchor plate to your lower throttle housing bolt hole. Also included is a tension adjustment tool that you can keep on your key ring. Keep the applied tension lightly adjusted so it's easy to roll the throttle off.

Fits bikes with dual cable throttle housings.

The Folding Bar End Mirror has a beautiful case mirror backing plate and the arms are one-piece, eliminating screws and mirrors vibrating loose. The nylon swivel allows just the right amount of tension to be maintained for easy adjustment. 

Features and Benefits:

• Stem Length: 2-1/2 in.
• Fits 7/8 in. handlebars only
• Black
• Sold in pairs
• 3-5/16 in Dia. x 9/16 in Dia

This new mirror screws into your stock mirror mount but can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price. Fits either left or right side.

Sold individually. 

  All Yamaha's will need a mirror adapter if you have the stock perch.

PSR dual sport mirrors come with a slightly convex mirror for a wider field of vision behind you. The round mirror is 4.25" in diameter while the oval is 3.75" x 3". These mirrors are easily adjustable and fold out of the way quickly with the 1" RAM mounts.

The RAM Ball Stud Base used for both mirrors will go into any standard 10x1.25 threaded mirror base.

Sold individually. 

 All Yamaha's will need a mirror adapter if you have the stock perch.

The Enduro Kit is a great option for your street legal dirtbike if you fold away your mirrors often. The longer stem helps the reflector fold behind the headlight and gives good visibility when extended. 

• Made from super tough glass reinforced Zytel.
• Reflector diameter: 4" (100mm)
• Overall mirror length 8.25" (215mm) (not including arm mount)
• Convex lens meets SAE and CE specifications

Their Doubletake Arm 3.5" is perfect for aggressive riders- long enough to see, but small enough to tuck away.

The new Doubletake ball is oversized, and high quality nitrile rubber surrounds an aluminum base that won't degrade under extended compression. 

The Doubletake Base Kit includes 5 bolts to thread into every application (even reverse thread Yamaha's), without adapters. 

Sold individually.

This adapter will give you more mirror choices.

Yamaha mirrors have reverse threads on the right (throttle) side of the handlebars. This adapter allows you to mount a mirror with standard 10mm threads on the right side of your handlebar. This opens up many options for your mirrors, choose any 10mm mirror for your Yamaha.

• Torque spec: 5 Nm

Genuine Yamaha replacement throttle cables.

• 4.75" wide,
• Raises handlebars 2 inches and allows fore/aft position adjustment
• Provides dual pivot points for optimal bar positioning
• One piece design is made from solid aluminum for superior strength
• Available for 7/8" - 7/8" or 7/8" - 1 1/8" bars

Requires 7/8" factory bar clamps on bike

This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars.

Because these are offset there may be limited clearance between the gas tank and the risers when the bars are fully turned on some models, mainly when mounted to move the bars closer.

Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes Fork Seals and dust wipers.

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. No disassembly of your forks, no drilling of damper rods. Just change the oil to 5w and install the DDCs under the springs and hit the trails.

Stiffer fork springs are required to realize the full benefits of the DDCs. .42 kg/mm springs are the springs recommended for just about anybody out there. Please call if you have any further questions.

The DDCs are not recommended for use with progressive springs.

The DDC Install/Removal Tool which makes installation that much easier.

Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.

Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward. 

Simple to install and completely tunable for all conditions and rider preferences.

These springs are custom wound specifically for the XT225. Stiffer than the .36 kg/mm stock springs, these will make your front perform significantly better. Combine them with the Cogent DDC's and you will be very happy with the results. Sold as pairs.

The Modoc is an excellent replacement for the stock shock. With adjustable rebound damping and preload, you can tailor the performance to match your riding style.

Select the spring you want installed based on the load you plan to carry. For most riders, the 7.1 kg/mm spring will suit you perfectly. Weigh more than 250 lbs, or are loaded to the max, think about the 8.1 kg/mm spring. Please call with any questions.

• Dynojet jet kits provide a simple and affordable solution to carburetor tuning problems
• Kits increase power and smoothness throughout the rev range while maintaining optimum fuel economy

Designed for use with stock engines using either stock or aftermarket exhaust and air filters.

• Provides a simple and affordable solution to carburetor tuning problems
• Allows you to tune your bike for increased power and smoothness while retaining fuel economy
• Includes a guide booklet on how to install and use your jet kit to it's full potential

Twin Air's high quality materials and superior construction deliver unbeatable performance and protection. The hands-down choice of more World and National Champions than all other filters combined.

Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles without restricting airflow.

• Increased air flow over the stock air filter.
• Designed to increase horsepower and throttle response.
• Easily fits inside the factory air box.
• Larger surface area over foam filters which offers longer service intervals in dusty conditions.
• Four layers of premium cotton gauze provides outstanding filtration.
• Washable & re-usable, never wears out.
• One filter will last the lifetime of your bike.

Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air- the number 1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow

Extra dirt protection for your K&N filter. Our custom made oiled-foam filter sleeve wraps snugly around the K&N filter to give a first layer of protection against dust and dirt. Oil it like you would any other foam filter.

 This is a complete high-performance intake kit for the DR650 that includes our famous TM40 carburetor kit and a K&N air filter with ProCycle wrap.

• TM40 Carb pre-jetted and set-up for your particular DR650
• Custom throttle cables to work with the TM40
• Extra jets should you need them for fine tuning
• K&N air filter with
• Custom ProCycle outside foam wrap

Fresh o-rings ensure a tight seal and no oil leaks.

Oil Change Kit includes O-rings for: Filler Cap, Filter Cover, Strainer Cap and Filter Seal.

Valve Inspection Kit includes O-rings for: Valve Inspection Caps, Timing Inspection Cap and Timing Plug Cap.

Includes forged JE 89mm piston 10.5:1 piston, Rings, Clips, Pin, big bore sleeve and top end gasket set. You will have to have the big bore sleeve installed in your cylinder and bored to fit the larger piston.

Need to remove your clutch assembly to get at that dreaded neutral safety switch? This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub. Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut easy. All of that and no worries about doing any damage to your expensive clutch hub.

The HelmetLok cable is coated, to protect your helmet and bike. Small and compact enough to fit in your pocket, jacket or on your belt loop. HelmetLok is designed to lock your helmet to any bike using the handlebar or frame as an anchor point. A 'T' Extension is included if you need additional space between the lock and your helmet, and for helmets with quick release buckles.

Don't be weighed down carrying your helmet around anymore. Just use the simple to operate, carabiner-style HelmetLok and you can secure your helmet using the convenient outward opening mechanism. The combination can be reset to the number of your choice. Enjoy security and freedom with a HelmetLok.

These flat tie down 'stretch' straps are designed specifically for motorcycles, ATVs and snowmobiles. Carry anything on your motorcycle securely and without scratches with these flat - no hook - tie down straps.

ROK Straps are a two-piece strap with a quick-release buckle in the middle and loops on each end. One end of the strap is a heavy duty nylon, the other has a strong stretchable section. Instead of hooks that can slip or come undone, ROK Straps have a loop sewn in each end. you pass the buckle around your frame, rack or other secure point and then back through the loop in the end making for a very secure mount. With each end secured, connect the buckle in the middle and simply tug the slack end of the strap until your load is firmly held in place.

CNC laser cut from 1/8" aluminum with a large 12.5" (length) x 10" (width) mounting surface area. Quick installation with a 4 point mounting system and no modifications required. There are integrated turn signal mounts, along with multiple strap slots for securing gear bags and cargo. All hardware and instructions are included.

The Rack is compatible with all RotoPax mounts.

You may purchase the rack alone, or you can order the Rack with the RotoPax.

The Stash Box is a weather resistant storage box that mounts between the motorcycle and the license plate. It is ideally suited to storing the vehicle registration and other small objects while remaining unobtrusive. The Stash Box has features that provide benefits over other motorcycle storage devices i.e., low cost, concealed mounting location, lockable, vehicle styling is unaffected, and easy accessibility.

• Sized to work with all standard size license plates as well as the current Wisconsin and Ohio plates
• External Dimensions: 7" x 4" x 1" plus 1" on the width for the lock
• Made from molded polypropylene
• Includes all mounting hardware, retention pouch for paper documents, foam insert, lock and two keys

Front fender from ProCycle Plastics (formerly DSA) is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does. Vacuum molded, these are a design improvement over stock. These are fully compatible in any combination with the original factory plastic.

Formerly DSA, now ProCycle brand, is a plastics kit in three colors - Black, White, and Blue, as well as Blue fenders with White side panels and Black fenders with White side panels. (headlight cowl not included).

Vacuum molded, these parts are a design improvement over the stock pieces. The side panels have a crisper, more angular look than the stock parts while the front fender is shaped like the DRZ400SM OEM front fender. Big enough to be functional without wind-steering the bike like the stock fender does.

Kits include front and rear fenders, a new LED tail/brake light and license plate holder, and both side panels.

Add a fresh new side panel hardware kit and an adhesive heat shield for a fresh off the showroom floor look.

Add a Maier Mfg. headlight cowl if you are doing a complete color change to your DR (must select plastic kit with head light cowl option)

Molded using a very durable, lightweight 1/8" thick polycarbonate - giving the windshield a high impact strength and making it shatter-resistant with a superior light transmission quality. Mounts quickly and easily onto the stock headlight cowling for a clean factory look. Drilling of the cowling is required, hardware is included. Removal for trail riding is also quick and easy.

The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.

Mounting is accomplished by drilling two holes on each side of your headlight cowl using the provided template. The shield is 14 inches tall, 11.5 inches wide at the bottom narrowing to 8.5 inches at the top. Made from military aircraft grade cast acrylic.

This unit will not fit properly on '90 to '01 DR650 headlight cowls.

Replacement side panels from ProCycle (formerly DSA). These pieces are fully compatible in any combination with the original factory plastic. These side panels have a crisper, more angular look than stock. Vacuum molded, they are a design improvement over the stock panels.

Sold in pairs
Does not include heat shield. Depending on your application and preferences, more than one optional heat shield may be useful.

The best product for those surfaces that mate together without a gasket. Like center cases, cam covers and the like.

• Heat-resistant
• Tough, durable sealer utilizing silicone rubber as a primary component
• Ideal for applications where a long-lasting, faultless seal is absolutely critical
• 3.5 oz. tube

Extra protection in bad weather to help keep your hands warm and dry. These nearly double the protection from most plastic type deflectors.

The outer shell is made from heavy-duty 500-denier nylon with 1/2" closed cell foam to keep the wind, cold and rain off of your hands.

• Protect vital engine parts and cases from rocks and debris
• Clear anodized for corrosion protection and good looks
• Skid plates made from 3/16" 5052 H-32 aluminum
• Smooth underside won't snag when crossing logs
• Oil drain hole
• Heat-treated chromoly steel clamps keep plates mounted securely
• All mounting hardware included

• Protects engine from rocks, logs, and other obstacles
• Prevents frame stretching
• Black anodized lightweight & strong aluminum
• Bolts on in minutes
• All hardware included
• Prevent the costly replacement or repair of a frame!

The Go Cruise cruise control mounts over the throttle grip and rests on the brake lever to hold your throttle open, allowing you to stretch and rest your hand on long rides. Installs and removes in seconds with no tools. You can roll off the throttle manually to disengage the Go Cruise.

NOTE: These will not work with Warp 9 levers

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam. On top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as sock seats using the two bolts into the chassis, which provides a closer fit to the bodywork and tank.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam.  On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as similar to stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.

Seat Concepts dual-sport/adventure seat-kits incorporate a wider seating area for the rider, which results in more even weight distribution, while reducing pressure points. Each individual seat model has been specially designed to increase comfort without compromising ride-ability. The more aggressive the bike, the more aggressive the seat-kit.

Each kit contains detailed instructions for easy "Do It Yourself" installation. This provides the highest level of quality & comfort at an affordable price.

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.

The ProCycle seat was designed for both comfort and function. Our seat is built with a premium grade foam that is denser for those long days in the saddle, and also giving you freedom to move while standing. 

The wide and sturdy seat makes long rides more comfortable. The vinyl weave helps keep you cool by letting air flow between you and the seat. The front of the seat is narrower, giving you space for your knees when you're standing, while the sides have grip so you can hold on with your knees while riding. If you choose the gel cushion option, it helps improve blood flow, prevents pressure points, and makes it easier to ride for longer without getting tired. 

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable! 

Available as a Foam and Cover Kit for OEM pan. This kit DOES NOT include the pan.

These pegs from SW Motech are a very cost effective way of getting a much larger footpeg than stock under your feet (2" by 3"). The removable and replaceable rubber cover is a another great feature. It helps isolate vibrations through your feet on those long highway jaunts but you can remove it in a few minutes when you get into slippery conditions that require better traction. Last but not least, you can change position a full 15mm. Two mount holes where the peg bolts to the mount allow that much adjustability. Entire peg mounts right up to your stock frame foot peg mount, no modifications necessary.

The pegs are made out of stainless steel and attach to a CNC machined aluminum bracket that goes into your stock mounts on your DL. These can replace your worn out stock pegs, give you a rubber peg when needed and a serrated edge when needed and look great doing it, what more could you ask for?

The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option. 

Wider foot pegs for sure-footed comfort. 

17-4 cast stainless steel.

Permatex Gasket Remover will help you remove that stubborn gasket without having to scrape so much, possibly damaging surfaces. Prepares surfaces for new gaskets. Give it plenty of time to soak in.

The Shorai LFM Standard Recommendation is the best overall pick for most applications, and has been selected to give strong cranking performance and long lifespan.

• Capable of holding a charge for up to one year without maintenance
• Two to four times the life of lead-acid batteries
• A Battery Management System that protects the battery from over-discharge.
• Carbon Fiber Composite case
• Stronger cranking for better starts
• Environmentally friendly, just discharge and dispose
• Ultra light and compact

Measures 4.5" x 3.5" x 2.28"
Weight (lbs): 1.34 lbs
Weight (kg): 0.61 kg
Cold Cranking Amps: 135
Polarity: [- +]

Each Shorai battery includes self-adhesive foam panels to achieve a snug fit in your battery box.

Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides it's extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position. There is no hazardous acid or heavy metals and it is non-explosive and non-combustible.

The Firepower features Increased cranking amps over lead acid batteries and has a very fast recharge cycle and can be brought up to a 90% charge within 6 minutes and also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.

145 CCA 12V/28.8WH
Package Dimensions: 4.75" x 3.00" x 4.50

• Mini Mechanical Speedometer is only 2.4 inches diameter.
• 0 mph - 140 mph
• Works with 12mm Japanese speedometer or odometer cables.
• Water-resistant and vibration-resistant
• Backlit with 12V bulb, Illuminated dial for night riding.
• Mounts to handlebar bolt or use the bar clamp supplied.
• Smaller, lighter and more accurate than the stock unit.

• Separate circuits for lighting and ignition
• 95 Watt lighting output
• Fits under the stock flywheel with no modification
• Replaces the stock OEM stator

Latex free gloves for the shop or garage.

• 10 Pack

This tool helps ease the pain of accessing the neutral safety switch. This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub.

Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut a breeze, and minimizes the likelihood of damaging the clutch hub.

The Clymer shop service and repair manual. It has all the necessary info to do any maintenance or repairs to your XR650L.

Genuine Suzuki Factory Service Manual for the DR200.

'75 - '91 XR75, XR80, XR100, XL75, XL80, XL100S

Clymer manuals are the most user-friendly repair manuals. They are written for the do-it-yourself-er as well as the experienced mechanic by industry experts. Step-by-step instructions based on the complete disassembly of the machine. This manual in written to cover 90-94 models but nearly all of the information will apply to newer models also.

This high quality socket from Motion Pro, is specifically designed to reach into the very small, deep space where the spark plug of the XR hides.

Normal sockets simply won't work in this case.

• Allows precise valve lash adjustment without disturbing the setting when the lock nut is fastened
• Knurled knob on adjuster drivers ensure a precise and secure grip
• Integrated repositionable wrench handle holds the lock nut while the drivers are used to loosen or tighten the valve adjustment screw
• Includes 10mm socket with straight slot adjuster
• Fit motorcycles and ATVs with straight slot screw-type adjusters and 10mm lock nuts

• An on-bike GPS system with all the features you've come to expect from Trail Tech
• View, organize, edit and share entire trail systems in 3D
• Designed specifically to meet the needs of off-road riders
• 240x400 LCD display - Readable even in intense sunlight
• Crash resistant, off-road design
• Upload routes from any GPS
• Customizable user screens
• Accurate tracks, even in the toughest terrain
• Runs on vehicle power or internal battery
• Back-lit for operation in the dark

These clever tie-down clamps give you an instant anchor point for tie-down straps using your hand grips.

• Oval opening for single or double tie-down hooks
• Clamps securely to any 7/8" handle bar grips
• Machined from forged aluminum
• Sold in pairs

Navigation doesn't get any simpler than this. Here is the ProCycle 'binary' Navigator. Don't know which way to turn? Flip the NAVIGATOR and follow your nose. It is guaranteed to lead you somewhere. Probably some place you have never been.
We include a lanyard so it can be flipped with gloves on without dropping it.

Genuine Kawasaki replacement chain guide. This guide mounts to the lower swing arm.

Chain guides are subject to wear over time due to friction produced by chain movement. To restore optimal performance, replace them with this authentic Yamaha component.

Changing sprockets for gearing can wear out the lock washer after a few uses. This is an OEM replacement.

Clip style master link for the EK 428 O-Ring chain. Keep one in your tool kit for trail side repairs.

The KLR650 is rather hard on the cush drive rubbers. Replace these any time you feel excessive play in the sprocket hub. Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.

Counter shaft seals can wear out over time. Replace it with a genuine Yamaha counter shaft oil seal.

Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on 12-24 volt DC circuits.

Increases fuel capacity for longer range than stock. All necessary hardware is included.

Available in white only.

Extra protection for your motor! Strong magnet at the end of the plug picks up ferrous metallic flakes in your oil, protecting your engine!

Adhesive heat shield for your new side panel plastics to protect it from the heat of your muffler.

Depending on your application and preferences, more than one heat shield may be useful.

Dimensions: 2"x3'

Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.

Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.