If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.
This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.
Machined from billet alloy and anodized for good looks.
Not for stock fuel tanks!
A replacement gas cap for your IMS tank. Newly redesigned to resist damage from new fuel additives that were hard on the seal in the old style cap.
Fits all TW200's. Includes a new cap and uses the stock petcock. Capacity is 2.7 gallons (stock tank is 1.8 gallons).
Clarke tanks do not come with a vent hose or vent cap.
Please note: All Clarke TW200 tanks have blemishes due to the mold used in their manufacturing process. Also, side panels are likely to not snap into tank as they do on the stock tank.
Replace these any time you feel excessive play in the sprocket hub.
Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.
Sold as a full set.
Polyurethane drive cushions for the KLR650. Polyurethane has a higher abrasion, cut, and tear resistance than rubber as well as much better resistance to chemical breakdown. This will offer longer life and better damping when compared to the rubber counterpart.
A portable device that can jump-start your motorcycle or car. It can also charge your cell phone, GPS unit, laptop or other electronic devices via USB cable.
The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option.
Wider foot pegs for sure-footed comfort.
17-4 cast stainless steel.
| Width | 1.97" |
| Length | 3.18" |
Services two Pivot Pegz and fits MK2, MK3 and MK4 Pivot Pegz
Kit Contents:
2 high-quality bushings per set. They recommend changing bushings every 40 hours or at least once a year to get the best performance out of a set. If you are on an Adventure Bike and are doing a lot of road miles they recommend swapping out bushings once a year to ensure that you get the most vibration dampening of the bushings.
Every new set of pegs comes with a 90A bushing installed. This is a medium flex rating.
80A is the softest and 95A lock-out is the stiffest and has the least amount of flex.
The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference.
The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.
For use on Motion Factory Foot Pegs Only
Here is an adjustable height centerstand from T-Rex Racing. If you are running supermoto wheels or lowering links, this centerstand will be much easier to use.
T-Rex stands are made from steel tubing finished in black powder coating for durability. Back by a 3-Year limited warranty for any material or manufacturing defects. Rest assured that you are getting best material commercially available.
Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools.
Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability. These Aramid fibers have a high strength-to-weight, thermal stability and abrasion resistance to provide advantages over steel fiber-based products. They provide excellent stopping power without noise and rotor galling but still provide fingertip control and strong, predictable brake response.
Double-H sintered metal brake pads feature the HH friction rating, the highest in the industry. These pads provide maximum brake effect and last twice as long as organic pads.
Semi-sintered pads have an all new recipe containing 30% copper by weight with an organic matrix. This design combines the long life of a sintered pad with the great feel and lack of rotor damage common with full-sintered pads. These can be used to replace Kevlar or sintered metal compound pads.
Set includes pads for both front calipers.
DP brakes are available in two different compounds for the DR.
The standard Sintered metal material pads provide powerful braking with industry-high HH+ friction rating that is equally adept in wet or dry conditions. They have a quick break-in period and excellent initial response. An oxide-based ceramic material on the rear of the backing plate keeps heat away from the caliper piston and fluid in extreme conditions giving a fade-free performance in even the harshest conditions.
The material in the Special Pads was developed by pro riders in the MX, Supercross, Enduro and Off-Road world where performance and good durability are essential.
Includes front and rear brake pads.
These awesome rotors are laser-cut out of a high-carbon content 410 stainless steel, lap cross hatch ground, and heat-treated. The finished rotors are mounted on a floating black steel carrier for durability and strength.
The floating pins are an oversized CNC machined stainless rivet with stainless wave washer to ensure these rivets will not crush like more traditionally used steel pressed rivets. high temp paint is applied to surfaces like cooling holes and edges to provide a clean finished look.
Includes a fresh set of brake rotor bolts.
New from Warp 9, a full floating 320mm Supermoto disc with caliper relocation bracket! These rotors have an additional hole for placement of a magnet for an electronic type speedo like the Vapor.
Includes a fresh set of brake rotor bolts.
Provide protection for your motorcycle’s front brake and clutch levers with Barkbusters aluminum bar lever protection handguards. Model Specific, these guards feature heat treated full wrap aluminum backbones that mount at two points on each side for strength. Prevent costly damage to your motorcycle with Barkbusters aluminum bar lever protection handguards.
Features:
Add Plastic Handguards for a complete kit.
Yes, plastic! This is a product from our friends at Acerbis. Ultra tough injection molded reinforced composite. Flexible Heavy-Duty Polypropylene will not effect chassis ability to flex, will not effect handling
It's twice as thick as a metal skid plate but is only half the weight. Plastic glides over rocks and roots better than aluminum. It also reflects less engine noise, bike will run quieter and cooler compared to alloy skid plate. Full coverage, mounts to existing threaded holes at the rear of the frame.
These plates are made from 4mm thick 5083 aluminum because the extreme abrasion and impact resistance for the full weight of the bike and the rider. The front portion of the B&B Skid Plate bolts to mounts that are permanently attached to the forward motor mount. This means no more trying to hold clamps in place when you take you skid plate off for oil changes or cleaning. Easy off, easy on. All necessary hardware is included in the kit. The plate has foam or rubber wherever there is contact with the frame.
Choose from a polished finish or a black polymer coating.
Protect your brake rotor and fork lowers from mud and debris. Choose between black or white.
PSR has a new shark fin rear rotor protector for the big XR and XRL. CNC machined from forged aluminum and then anodized gun metal in color. This unit bolts to the stock caliper bracket.
Warp 9's CNC shark fin rear rotor protector. To make installation super-easy this fin bolts to a brand new CNC machined caliper bracket. Just remove your existing caliper bracket and remove the pins, install them on this new one and then put the caliper and fin back on.
Made from strong and light 5052 aluminum to hold your license plate firm and up out of the way for maximum tire clearance, prefect for your new dual sport bike.
It uses the original tag light without any modifications to your bike. Mounting hardware and instructions included.
The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.
This windscreen mounts securely to the three stock windshield holes as well as the two side cowling mounts. The shield is 14 inches tall, 13 inches wide at the bottom narrowing to 11 inches at the top. Made from 3/16" military aircraft grade cast acrylic.
Stock Suzuki choke knob holder guide. Replace your cracked or cross threaded stock unit with a new one.
Precision tolerances – The tightest in the industry. Ultra-lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.
The complete fork upgrade kit - your choice of springs and Race Tech Gold Valves. Also includes a set of top quality fork seals and 5W fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
You can select from various straight rate springs to customize the package to your needs.
Stock Spring Rate for XR650L: 0.44 kg/mm
DRZ400 E/S
A pair of Race Tech fork springs to dial in your front suspension to suit your weight.
Fits all DRZ400 models with conventional forks (not for SM)
Recommended spring rates:
| Rider Weight w/gear lbs. | Spring Rate |
|---|---|
| 90 or less | .42 |
| 90-119 | .44 (stock) |
| 120-150 | .46 |
| 150-180 | .48 |
| 180-220 | .50 |
| 220-250 | .52 |
| 250+ | .54 |
Helps protect vulnerable fork tube and seal from dust, dirt, and corrosive elements. Hook & loop (Velcro) fastening on back side makes installation or removal for cleaning a breeze.
Cogent Dynamics Mojave product is a drop-in replacement for the DR650 stock shock, no modifications necessary. Mojave is not simply an improved Suzuki shock, it is a brand new replacement shock that is a totally engineered suspension solution to suit your needs.
Each shock is assembled and tested on the Cogent Dynamics suspension dyno before being packed up and shipped. Like its bigger brother the Mojave Pro Series, this will make an incredible difference in the handling of your DR.
Mojave Improvements over stock:
Mojave upper mount: uses a precision spherical bearing with dust seals, which accurately transfers damping forces to the motorcycle frame.
Internal improvements: Cogent designed shaft, seal head, damper piston, adjuster and clevis.
Mono tube construction: precision honed, super-stiff steel body with an upper body cap machined from billet aluminum.
Built-in billet aluminum separator piston provides an in-line gas pressure reservoir which eliminates the Suzuki rubber bladder.
This shock package includes the CNC machined Bling Ring Preload Adjuster Collar and Preload Bearing that will make preload adjustments easy.
Select the spring you want installed based on the load you plan to carry. For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring. If you regularly have more than 250 pounds the bike, you might want to use the 8.15 kg/mm spring. If you have any questions at all about this, please call.
You may choose to add the Hydraulic Preload Adjuster to make it the easiest of all. All you do is twist the knob. Includes mounting bracket for knob unit. (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)
Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.
Complete kit to replace the bearings and seals in the XR650L shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Spherical Bearing | 1 |
| Snap Ring | 2 |
| Seal | 8 |
| Needle Bearing Shaft | 3 |
| Needle Bearing | 6 |
| Bushing | 2 |
This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.
Features:
This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, drilling, or wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.
This kit is available with either a chrome or black chrome reflector in the headlight.
Check out the images for stock vs. LED patterns and brightness. (Images are of a DR/DRZ unit, but the light unit is the same as that on the XRL.)
This kit includes a DOT LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
How does this headlight compare to our original TW200 kit? First and foremost, this kit has SAE/DOT markings and a much wider/brighter high beam pattern. The low beam is very similar to our original kit: wide, flat, and bright but with more punch. The DOT headlight assembly has also proven to be more durable than the original headlight.
Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Approved
CE, RoHS, ISO9002, IP67
No cutting, drilling, or wiring modifications! Installation takes 5 minutes.
Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.
Please note that this product is not compatible with the 1987 TW200.
This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 1996-2020 DR650SE. No wiring, soldering, resistors, drilling, or fabrication required however due to the size of the headlight minor trimming on the backside of factory plastic headlight fairing is needed in non-visible areas.
These heavy-duty aluminum brackets are laser cut from 0.190" 5052 Aluminum then powdercoated black. Designed specifically for mounting auxiliary lights to the front of your DR650, the mount goes between the fender and the lower triple clamp. Longer fender bolts are included in each kit. installs in 10 minutes.
Three options are available: two different dual mounts that place the lights outside the fender and a single, center type mount. The 2" mount is for smaller type lights and is 8-5/8" between the mounting holes while the 3" is 10-3/8" between the mounting holes. If you are going to use larger style lights, the 3" mount is for you.
Note! The Dual 2" and 3" mounts do not work with the Acerbis 6.6 gallon tank! They make contact prior to full lock. Mounts are fine with other oversize tanks.
Made from heavy duty 1/8" thick stainless steel, these mounting brackets are specifically designed for mounting 2" LED auxiliary lamps to the front of your TW200. They position the lamps (not included) high & tight to the bike for optimal protection and light projection without interfering with the bike controls, body work, or fuel tank. Kit includes four longer mounting bolts for the lower triple clamp.
The image shows a GoPro camera on the TW's right side and an LED light on the left. You could certainly do something like that as well!
From our friends at JNS Engineering, a very nice mount for a set of auxiliary lights on the front of your KLR650. Laser cut from 0.190" 5052 aluminum it is CNC formed and then powdercoated black. One of the best benefits is that it will not interfere with even the largest aftermarket fuel tanks. All included mounting hardware is stainless steel.
This relay will fix your flash rate problem caused by aftermarket signal lights and/or integrated tail light. If your signal lights flash too fast or do not flash, this part is your solution! Plug and play - easy installation.
Only ONE relay is needed per motorcycle regardless of front and rear signal set-up.
This component works with the following signal configurations:
The relay comes preset to 85 cycles per minute. You can alter the flash rate to make it faster or slower. If you slip off the grey cover you can access an adjuster that will enable you to change the flash rate to your liking.
Please make sure your bike uses a 2-pin relay for the signaling system. If your bike has hazard lights it may need the 4-pin relay. Please also note the pin configuration and make sure it matches what is on your bike. It is very important to verify fitment before making your purchase.
This relay will fix your flash rate problem caused by aftermarket signal lights and/or integrated tail light. If your signal lights flash too fast or do not flash, this part is your solution! Plug and play - easy installation.
Only ONE relay is needed per motorcycle regardless of front and rear signal set-up.
This component works with the following signal configurations:
The relay comes preset to 85 cycles per minute. You can alter the flash rate to make it faster or slower. If you slip off the grey cover you can access an adjuster that will enable you to change the flash rate to your liking.
Please make sure your bike uses a 2-pin relay for the signaling system. If your bike has hazard lights it may need the 4-pin relay. Please also note the pin configuration and make sure it matches what is on your bike. It is very important to verify fitment before making your purchase.
Ensure your Honda XR150L doesn't malfunction with "quad-flash" when upgrading your signal lighting to LED units. This easy to install LED diode module is completely plug and play, meaning you don't have to cut, splice, or solder any wires during the installation process.
When upgrading your Honda XR150L with LED turn signals, it's necessary to install a diode module to prevent all of the signals from blinking at once regardless of left or right signal activation. Some riders choose to splice and solder their own solution, but we like things plug and play. That means all you have to do is plug in our kit and you're done! There's no need to cut or splice your stock wiring harness or break out the soldering iron and electrical tape.
You may have noticed after installing aftermarket LED turn signals that your blink rate has significantly increased. OEM flashers are designed for standard bulbs which draw a few watts each, much more than typical aftermarket bulbs or LED signals. This device is an effective alternative to using load resistors because it consumes considerably less watts, consumes less space, and does not generate excessive heat.
The plug is exactly the same as the OEM unit making swap outs a cinch. No wiring changes, cutting and adding connectors. Just plug it in and you will have a steady flash at the DOT OEM flash rate when aftermarket LED turn signals are installed. It is an all solid state design and will blink correctly with loads all the way down to 0.1W / 0.01A.
Not for any DRZ400 or Royal Enfield Himalayan
Not for use with stock bulbs.
We have worked closely with Magura to come up with a kit that fits properly.
Want an easier pull on your DR clutch? No cable to break? Then say hello to the Magura Hymec Hydraulic Clutch. Simply remove the stock perch, lever and cable in bolt this in its place. This system replaces the stock cable with a small lightweight hydraulic system for improved clutch control, easier operating pressure, a constant pressure point and smoother actuation.
Developed over many years and tested under the toughest conditions possible in the off-road motorcycle world. World champions to novices all agree on the benefits of the Hymec Hydraulic Clutch system. Due to demand, Magura is now making this available for many dual-sport motorcycles, and now the DR650!
Never hurts to have a bit of the Margura specific Blood Red hydraulic fluid sitting on your shop bench. 4 oz. bottle available as an option.
Replacement shift lever with folding tip for use with OEM footpegs.
Billet levers that are short enough to provide clearance for your hand guards. Warp 9 Flex Brake Levers are machined billet, anodized and hinged with a CNC machined master cylinder interface. Adjustable reach allows customization to the rider's hand size. Double hinge design allows lever to flex out of the way in most impact situations. These high quality levers are approximately 1/2" shorter than stock. Brake lever includes a nice billet clamp with nylon sleeve to allow the assembly to rotate on impact. These levers work with the stock brake light and clutch safety switches. Will not fit with the stock OEM wind deflectors.
Will not engage the clutch switch on 2010 and later models
In stock with limited availability in Clutch Lever only, discontinued item. "3-Finger" levers still available.
The elegant, open-end design makes these heated grips both stylish and functional. Highly efficient design, delivering warmth faster than traditional heated grips. Five-level temperature controller adjusts the grips accurately to avoid overheating. Specially selected rubber material resists the outdoor environment and provides a secure and comfortable grip. Even at high-temperatures, the grip remains resistant to damage.
Choose from the standard five level push button temperature controller, or the LCD display controller which shows the selected heat level and available battery voltage.
High quality replacement cables from Motion Pro.
The Phillips type screws used in Japanese motorcycles are actually Japanese Industrial Standard (JIS) screws are very easy to strip if you are using a regular Phillips screwdriver.
All the advantages of a flatslide pumper carburetor at a much friendlier price than a Keihin FCR.
Our complete genuine Mikuni TM40 pumper carburetor kit comes with alloy adapter rings bonded to the carburetor body for a firm reliable fit in the stock air boots. We also include new 3" longer than stock throttle cables, a remote mounted choke knob, complete instructions along with a wide range of main jets and pilot jets for fine tuning or to accommodate bikes with extensive modifications.
Geared for the do-it-yourselfer that already has a TM40 or HS40. This kit supplies everything you need to convert it for use on your bike.
Kit includes intake and air boot adapters, throttle cables, choke knob, accelerator pump nozzle, a wide selection of main and pilot jets plus a TM40 tuning manual.
Comes with everything you need to freshen up your carburetor.
Here's a UNI dual layer foam air filter element for the KLX230. Needs to be treated with air filter oil like any other foam filter.
Cycle Racks Bag Supports can used for many different Cycle Racks and can be used on either the front or rear rack.
When they developed these, they wanted a functional, yet "Easy On- Easy Off application. The pig tail hook goes up, over and underneath the bar of the rack, they can also be used upside down on the rear rack as side boards. To install them, wing them out, slide them in place and then wing them back down. Simply reverse the process to remove them.
Rok-Straps are supplied to secure them in place. They are pre-drilled to accept the pattern of the Roto-Pax Pack Mount (sold separately) so you can carry fuel or attach them to your own bags.
They are sold together in a set of one right support and one left support.
COLOR: Black
Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.
The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary har
Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets and that will be no problem. See bottom image.
Note: Placement of this top rack does require removal of the stock tool bag.
Designed to make your compact rack even more versatile for riders who need a larger luggage platform.
CNC machined from 5mm aluminum 5083 plate with lots of slots to attach your Rok Straps (or other straps). This gives a considerably wider deck than the standard B&B Rack. Attaches directly to the B&B rack with four screws that are included. Available in either polished aluminum or a black polymer coating.
These plates are pre-drilled and countersunk from the bottom making installation of a RotoPax mount quick and easy.
Some older carry racks will not have predrilled holes in them to mount luggage plate in which it will require you to drill yourself (select pre2018 version)
This is for the add -on Top Plate only.
Fits B&B Luggage Rack purchased AFTER 2018
The Bag Snake kit works great for rear bags and side bags. When rigged with a side bag the second ring on the ring tensioner creates a secondary buckle so you can loosen the top for access and your bag doesn't fall away from the bike.
When rigged for a rear bag the diagonal section of the strap prevents any slippage over the ends of the bag. For this reason, the Bag Snake is great for smaller rear bags.
Kit Includes:
Every backcountry adventure-seeker needs a handful of these multi-purpose straps with virtually unbreakable fasteners. Each pair of stretch polyurethane Pronghorn Straps™ feature stamped aluminum buckles sheathed for scratch protection with arrows that line up for easy fastening. Each buckle prong holds the strap in place for pre-fitting and easy chaining of straps together.
Available in color-coded 18-, 25- and 32-inch lengths and marked by size, you’ll find a million uses for Pronghorn Straps—motorcycle, sled, snow bike, 4×4, ATV, UTV/SXS—and so much more!
The DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 84db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.
If your aftermarket exhaust is missing heat shield mounting points, this is the easy fix you’ve been waiting for.
Includes one stainless steel mounting bracket with M6 threaded nut, and one stainless steel hose clamp.
Fits exhaust approximately 1.1inch-2inch diameter. Trimming may be required for smaller diameter exhausts.
This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 2008-2018 Yamaha XT250. The new design for the black headlight produces more light and has much more uniform beam pattern when compared to the previous version. New design currently only available in black, chrome may be available in the near future. No wiring, soldering, resistors, trimming, drilling, or fabrication required.
A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.
Fits 520, 525, and 530 pitch chain.
These wider seat kits from Seat Concepts keep you comfortable on those long commutes or dual sport rides. The added width and improved foam density will help keep your seat from being the item to stop you from going on those big rides or enjoying the bike.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
| Width: | 9.5" (241mm) |
| Height: | Same as OEM |
These wider seats from Seat Concepts help keep you comfortable on those long commutes or dual sport rides. The added width and improved foam density help keep your seat from being the item to stop you from going on those big rides or enjoying the bike.
The Complete Seats come fully assembled on an aftermarket seat pan, and are ready to install and ride.
| Width: | 9.5" (241mm) |
| Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!
The Complete Seats come assembled with an aftermarket pan and ready to ride.
The Commuter shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but is much more dished out towards the mid-point to distribute rider weight over a greater area. The passenger platform has been built up to help prevent the passenger from sliding into the rider.
The Commuter seat is the best choice for extended pavement riding and mellow offroad. The unique shape and added width will provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
| Width: | 13" (330mm) |
| Height: | Same as OEM |
Machined from impact and wear resistant chromoly steel. Heat treated, then finished with a nickel coating for corrosion resistance.
Quality steel front sprockets. Choose 13T through 15T. The stock size for the XRL is 15T. Go down in tooth count for faster acceleration.
High quality steel rear sprockets from 39 to 53 teeth.
Sprocket color may differ depending on size.
These quality sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
JT steel rear sprockets are manufactured using only the finest grade of C49 high carbon steel.
Two styles of rear sprocket were used on the DR350. The 90-95 'S' and 'SE' (street legal) models have a cush drive hub. The 96-99 'S' and 'SE' as well as all of the 'dirt only' models have a non-cush rear hub. Select your sprocket accordingly. If you are not sure, look at your bike. If the sprocket is bolted directly to the wheel hub you have a non-cush model. If your sprocket is bolted to a separate sprocket carrier you have a cush drive model.
This is a complete drivetrain package. All the parts you need to freshen up the most important part of your motorcycle.
Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.
Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.
Available in 9.5" aluminum (ideal for travel) and 16" forged steel (useful in a home shop/garage)
Introducing the Armadillo Bag®—your new best friend for on-the-go adventures! These flexible, collapsible, and lightweight utility bladders are perfect for safely transporting and storing liquid hydrocarbon products, as well as other powersports and automotive fluids. Choose from a variety of sizes: 1, 2, 3, and 5 gallons. Plus, each bag comes with a handy pour spout for easy use.
Features:
Armadillo Bags are not portable fuel containers as described by ASTM, EPA, ARB or other state and federal agencies. Armadillo Bags are NOT intended for fuel storage or transport in the USA.
| Rolled Empty diameter | 2.5 inches (6.35 cm) |
| Weighs | 0.75 pounds (12 oz) |
| Flat Filled dimensions | L x W x H: 16.5" x 10" x 3" (41.91cm x 25.4cm x 7.62cm) |
Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position.
The Firepower features increased cranking amps over lead acid batteries and has a very fast recharge cycle, and can be brought up to a 90% charge within 6 minutes. It also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.
165 CCA 12V/36WH
Package Dimensions: 6.20 x 3.70 x 4.45
The Battery Tender® Junior Selectable is much more than a trickle charger. It has a brain. It's lightweight, compact, and fully automatic; very easy to use, especially in small spaces. It will keep your Lead Acid, AGM or Lithium battery fully charged so that it is ready to go when you are
RotoPax holder made to mount a single Fuel and/or Water container.
This unique design adds strength and provides extra tightening power.
Use with included base plate or remove plate to attach mount direct by bolting up through the bottom or down through the top.
Always a good idea to put in a new set of Oil Change O-Rings at the first sign of any leakage. This package gives you the three most important: oil filter cap and the one behind the filter as well as the one on the filler cap. All are new OEM Suzuki O-Rings.
Big bore kit for the 2003-2005 CRF150F. A simple bore in bore kit that includes BBR's high performance camshaft and valve springs for added performance. This cam features higher lift and duration than stock. Complete kit includes piston, rings, pin, clips, BBR MX cam, valve springs and gaskets. This is the quickest way to add the most power to your bike. Great when combined with our exhaust system, Rev-Box, and Free-Flow airfilter. Requires machining of stock cylinder for installation.
CNC machined oil filler cap with locking clip to keep it in place in the roughest conditions. The cap is pre-drilled and the locking clip is safety wired to the mounting tap with a section of silicon tubing, that will not melt or discolor, over the wire. First class all the way. Available in Silver, Black, Blue or Red.
Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
Grab our 5-pack and save both time and money!
Fresh o-rings ensure a tight seal and no oil leaks.
Oil Change Kit includes O-rings for: Filler Cap, Filter Cover, Strainer Cap and Filter Seal.
Valve Inspection Kit includes O-rings for: Valve Inspection Caps, Timing Inspection Cap and Timing Plug Cap.
Here is the little switch that mounts inside your brake or clutch lever perch and controls the brake light or clutch safety circuit. This switch often gets damaged in an unplanned dismount (aka: crash) or the plastic simply cracks from age. When this happens, you can find yourself chasing a short circuit that keeps blowing your fuse every time the brakes are applied. If this has happened to your TW, here's the fix!
This advanced filter oil & cleaner kit by No Toil is alcohol free, completely biodegradable and compatible with all foam filters.
Protect your thumbs from blisters caused by riding on the inside of your grips.
Sold in Pairs.
The GCAG Mount Point is a sturdy piece of hardware to make it easy to attach soft luggage and straps to your motorcycle or any vehicle. Made of stainless steel, it will never rust and its strong enough to hold any luggage you care to throw at it.
Sold individually.
SUGGESTED USES:
FEATURES:
DIMENSIONS:
Made for the true adventure rider, the K784 has everything you need to get you anywhere on or Off-Road.
Kenda's Dual-Sport tire designed for the 80% on-road, 20% off-road crowd.
The Shinko 244 is a very popular tube-type upgrade for the front tire on the TW200 or the VanVan. DOT approval coupled with excellent performance both on and off-road make this tire a winner!
The 244 Series dual purpose street and trail tire is designed to be equally at home on dirt or pavement.
Available in 5.10-18 (69P load / speed rating) and 4.60-18 (69S load / speed rating).
The 244 Series Dual Sport street and trail tires were designed to be equally at home on dirt or pavement. Great value.
A fresh set of brake rotor bolts. These bolts already have thread lock compound applied to the threads.
Stock OEM bolts work with factory rotors.
For aftermarket rotors like Warp 9 or EBC, use aftermarket bolts.
Front comes in pack of 6
Rear comes in pack of 4.
State-of-the-art replacement seats, Sargent seats are built on a percision-molded lightweight Polytec seat pan. Sargent's proprietary seat foam (Super Cell Atomic Foam) is their own unique blend of resilience, firmness, and vibration-absorption qualities, making it well suited for long distance comfort and support. Sargent seats are covered in a marine-grade, UV-stablized mildew resistant CarbonFX vinyl.
