Gasket for the engine case cover over the clutch. Doing any clutch work, you probably want to replace this gasket so you don't have any leaks when you are all done with the project.
A high quality top end gasket set for the XR650L
K&L® shims exceed the maximum of the Apparent Rockwell Hardness "C" scale. Shims average 47.0 compared to the 46.0 maximum.
This kit fits KLR650 87-18 as well as other brands and models , please verify correct size for your model before purchase.
29mm diameter - Includes two valve shims of each size 2.30, 2.40, 2.50, 2.55, 2.60, 2.70, 2.80, 2.90, 3.00 and 3.10. In a shim box.
20 shims in total. From K&L.
BMW / KAWASAKI / YAMAHA
Billet plugs for your left side case.
Includes both the timing mark plug and the crankshaft access plug.
Keep your motor running right with fresh spark plugs!
NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.
Higher pressure in the cooling system, raises the coolant boiling point and increases protection from coolant loss due to overheating.
23 PSI - 1.6 Bar.
The complete Thermo Control package - Our in-house designed Thermostat Bypass kit, a set of Custom Silicone Hoses and a Hi-Pressure Radiator Cap. All combined to help your KLR cooling system be at the top of its game. The Thermostat Bypass kit includes a thermostat with a higher temperature rating that will keep the motor more in its happy spot.
The Silicone hoses are stronger than the stock rubber units and will better resist cracking and leaking.
The idler gear is one of the few plastic components in the DR650 that can significantly impact engine performance if it fails or breaks.
This gear is crucial for driving the oil pump, which ensures proper oil circulation throughout the engine. In the absence of this component, complete engine failure may occur. While the idler gear is not frequently cited as a common failure point in the DR650 engine, failures have been reported, typically manifesting as either a fractured gear or stripped teeth.
During inspection, it is essential to check for any cracks, chipped areas, or missing teeth on the idler gear. Replacing the gear is a straightforward procedure, and it is advisable to do so while the clutch side case cover is already removed for other maintenance tasks, such as NSU screw replacements or clutch hub bushing replacements.
This component is a Genuine Suzuki part.
Stage 1 - Excellent mid-range and top-end power increase.
Uses stock valve springs and rockers.
Does not incorporate compression release.
Mika Metals Hybrid Series handlebars are truly a marvel of engineering. It is the first oversize handlebar in the world that fits on 7/8" clamps.
The patent pending design is the most unique idea to shake up the handlebar industry in quite some time. They retain all the flex properties of the pro series handlebars and allow you to run oversize bars without the oversize clamps.
Constructed from the highest quality aerospace 7075 aluminum for maximum strength. CR High Bend, includes injection molded bar pad.
Bars only fit 7/8" clamps
ProTaper's ADV handlebars give you a bar taller than most with extra space on the control portion of the bar. These bars provide an additional 20mm of space next to where your levers and throttle are located for your GPS, phone cradle, auxiliary switches, etc . They come in Adventure (which is taller than stock) and Adventure High (which is even taller).
These are oversize bars, which means they are are 1 1/8", not the smaller 7/8" diameter. Therefore some bikes will require a adapter and there are several available to select from.
Using the same manufacturing techniques and materials as ProTaper’s industry-changing 1⅛" motocross handlebar, the EVO Adventure is specifically designed to provide adventure/touring riders with the increased comfort and control they need. With over 8" of straight section in the control areas, mounting vital components is made easier than ever. With its premium 7000 series aluminum alloy construction and computer-profiled four millimeter-thick wall design, the EVO Adventure Handlebar is up to 25% lighter and 45% stronger than competing handlebars.
This bar kit will raise your hands 5.5" up from the factory riding position. If you are over 6 feet tall, this is the kit for you! It allows for a more natural riding position, no more bent neck and being hunched over the bars. You will be able to ride comfortably and more aggressively by installing this kit.
The ProTaper bars are taller and tapered from 1 1/8" to 7/8" and the braided stainless steel brake line will be a serious improvement to your braking ability. Braking becomes more responsive and firmer while adding a stylish look to your TW200.
Everything you need is in this kit to properly raise your bars:
Requires 7/8" factory bar clamps on bike
These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.
These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.
Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).
Warp 9 has created a beautiful brake pedal machined from billet aluminum to an 8mm thick work of art. A stainless steel pin eliminates wear in the frame. This pedal has the ability to move the spring loaded brake tip 10mm either way from the center position. The arm is arched to provide clearance for riders who have the lowpeg + centerstand combination.
Replacement shift lever from IMS with folding tip.
A stock replacement brake pedal for the DR650. Nothing fancy but sure gets the job done. Just order it up and get back on the trail. See our Brake Pedal Adjuster Bracket that allows you to adjust the position of your brake pedal to perfection.
- Pivot CP clutch and brake lever set for Trail models.
- Lever folds outward to prevent breakage in the event of a crash.
- Lever adapter is ultra precise CNC machined out of high grade aluminum for super light weight design.
A set of replacement brake and clutch levers. Standard length.
A high quality replacement clutch cable.
For M8 handlebar bolts, the RAM-B-367U motorcycle handlebar base will replace the existing bolt with a 1" B size ball. This rubber ball base provides shock and vibration damping, and is compatible with a wide variety of B size RAM® double socket arms and device holders. The RAM-B-367U motorcycle handlebar base will work with any motorcycle that features an 8mm bolt or smaller on its structure. A smaller bolt can be used, though the load capacity decreases with the bolt size.
Not compatible with handlebars that have a cross bar.
This an OEM replacement nut for your front sprocket.
Reduce the friction dragging down your drivetrain. This chain roller is made from Delrin®, it's self-lubricating and a significant improvement over stock.
Does not use a bearing but rides directly on the frame boss. There is no mounting hardware included.
Chain guides experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.
Chain slippers undergo degradation over time due to friction associated with the chain's movement. To maintain optimal operational performance, it is advised to replace worn components with authentic Honda parts.
Quality steel front sprockets. Choose 13T through 15T. The stock size for the XRL is 15T. Go down in tooth count for faster acceleration.
Individual 14T, 15T or 16T front sprockets.
JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.
For reference, the stock gearing for the WR250R is 13/43 while the X model runs with a 13/42 stock configuration because of the SM wheels/tires. Both use a 108 link chain with the stock gearing.
The JT rear sprockets listed are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Limited availability on Aluminum from PBI. Manufactured from aircraft 7075 T651 Plate Aluminum.
If you want the additional low-end grunt that the 46, 48 or 50 tooth rear sprocket will give you, you will need longer chain as well.
New Rear Sprockets require new Sprocket Bolts because of a difference in the holes vs. the stock bolts.
Quality steel rear sprockets.
Color may vary based on manufacturer availability, quality will not be compromised.
Clip style master link for the EK 428 O-Ring chain. Keep one in your tool kit for trail side repairs.
High Quality chain. Will need to be cut to fit your sprocket combination.
All of these chains come with a clip type master link.
This kit includes 2 Needles that have been developed by JD Jetting and manufactured for them to their exacting specifications. These two needles allow a wide range of tuning possibilities and provide correct fuel delivery at any throttle position.
4 allen type screws for the float bowl are also enclosed should you strip out the stock screws during your tuning process. Complete instructions with photos, jetting suggestions for different set-ups and situations, 5 Main Jets and a drill bit complete the package.
Rebuild your crusty carburetor with parts from the same manufacturer the OEM companies use. Included in the kit are all necessary gaskets, O-rings, float valve and jets you need to rebuild your carburetor to like new condition.
This is an O.E. replacement diaphragm for your BST40 carburetor.
Included in this kit are the parts needed to repair a second generation TK carburetor. You get a new float bowl gasket, needle valve with O-ring, needle, mixture screw, and stock jets for the '01-'21 models kits.
Replacement rubber boot for choke knob assembly.
Heidenau tires are made in Germany and they are high quality motorcycle tires for street, off road and adventure riding.
A tire worthy of standing side by side with the legendary K60 Scout. The K60 Ranger is designed and developed to be the off-road cousin in the K60 family. This is not a Scout with different tread. Heidenau started from scratch with entirely new carcass and compound to maximize off-road performance and reliability.
“Rated by Heidenau as a 30% street / 70% off-road tire, the new K60 Ranger sits next to the K60 Scout in Heidenau’s lineup, offering a more off-road biased design to help adventure riders explore further into the backwoods with more confidence to tackle difficult terrain. Like the Scout, the K60 Ranger also gets a reinforced carcass with high puncture resistance. Where it differs is a more-open, knobby tread pattern that utilizes large gaps between center blocks, instead of a continuous center strip, giving it the ability to dig into loose terrain more effectively. What’s more, the Ranger utilizes a softer rubber compound that helps increase grip both off-road and on the street. Plus alternating side lugs, tied together with crossbars, enhance the tires ability to climb out of ruts and improve cornering stability.” – Rob Dabney - ADV Pulse
Tread design:
The K60 Ranger’s new tread design has dirt and big bikes in mind. While the open block design should keep the tread from loading-up in muddy conditions, the compound and carcass should keep the ride stable when you’re back on the street. With features intended to give integrity to the side blocks, the K60 Ranger should be at home on single track or cruising down the highway.
Tubeless tires (TL) can be used with spoke wheels, but Tube Type (TT) tires cannot be used with TL wheels.
This is a great Dual-Sport tire from Dunlop. Designed for the true 50/50 rider. An Adventure product for the price-conscious customer. Full tread depth pattern designed for rigorous off-road use yields excellent traction on everything from hard-packed fire roads to soft single-track trails. Versatile tire performance allows riders to travel on the street and venture off-road. A tire equipped to go anywhere, the D605 is a value option for the all-around rider. DOT approved.
Motoz Tractionator Desert H/T series of tires are renowned for great traction and long wear life. These tires are designed to handle hard terrain, fast and rocky trails as well as gravel roads and desert hard pack. Tricky off-cambers, ruts and hard braking at extreme lean angles are no problem for this DOT approved tire.
Note: Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.
Features:
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of the big Acerbis or Clarke tank? The 4.0 gallon tank from IMS might be just right. Includes cap, uses stock petcock.
More range at a great price.
The 3.6 gallon tank is for the off-road DRZ400 and DRZ400E.
The 3.9 gallon tank for the dual-sport DRZ400S. The 3.9 gal tank also fits the ES and SM models.
Both tanks are available in a selection of colors.
NOTE: Clarke tanks do not come with a vent hose or vent cap.
Does your stock vacuum operated petcock not shut off when your bike is parked? Replace your stock vacuum operated petcock with this manual one. Must be shut off any time the bike is parked for more than a few hours. Fits stock or aftermarket tanks. Plastic tanks may need the hole 'ovalized' to fit the dual standpipes.
Does not fit OEM XR650L metal tank
Includes all necessary o-rings and diaphragms
EBC Double H Sintered pads feature the HH friction rating - the highest in the industry.
Provides maximum brake effect and lasts twice as long as organic pads.
DOUBLE-H SINTERED METAL PADS
Provide maximum brake effect and last twice as long as organic pads
Feature the HH friction rating – the highest in the industry
Sintered Pads from EBC are the best pads we have found for the KLR, they provide good performance in all conditions yet still give you long pad life.
These sets include front and rear brake pads.
Sport Carbon pads:
Sintered Pads:
Race Sintered:
Includes front and rear brake pads
Includes front and rear brake pads.
Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability. These Aramid fibers have a high strength-to-weight, thermal stability and abrasion resistance to provide advantages over steel fiber-based products. They provide excellent stopping power without noise and rotor galling but still provide fingertip control and strong, predictable brake response.
Double-H sintered metal brake pads feature the HH friction rating, the highest in the industry. These pads provide maximum brake effect and last twice as long as organic pads.
Semi-sintered pads have an all new recipe containing 30% copper by weight with an organic matrix. This design combines the long life of a sintered pad with the great feel and lack of rotor damage common with full-sintered pads. These can be used to replace Kevlar or sintered metal compound pads.
Set includes pads for both front calipers.
Replace those worn out brake pads with quality EBC replacements.
Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.
Motocross brake rotor featuring ultra lightweight radically profiled contours for great looks, great self cleaning and brake performance. Made with tough and durable heat treated stainless steel. Heat treated to perfection and then diamond ground to micron accurate surface finish and parallelism and will deliver great brakes that perform well and last.
SMX Carbon Look Rotor
Quality components at a great price.
Ever had to turn back on the trail because of downed limbs? Or have you ever been moto camping and needed some wood for a fire?
This is the tool for you then! We have tried this manual chainsaw and it makes quick work of hard woods like Oak.
The chain itself is 25 inches long with 8 inch nylon straps at each end. All together this saw weighs 1/4 of a pound. This will tuck away nicely into any tool pouch or saddle bag as it roll up into a tight round.
The Moose Tire Bead Tool holds your tire in place as you work you way around the tire
Made of aluminum with a nylon screw so it will not scratch the rim
Sold in pairs
These flat tie down 'stretch' straps are designed specifically for motorcycles, ATVs and snowmobiles. Carry anything on your motorcycle securely and without scratches with these flat - no hook - tie down straps.
ROK Straps are a two-piece strap with a quick-release buckle in the middle and loops on each end. One end of the strap is a heavy duty nylon, the other has a strong stretchable section. Instead of hooks that can slip or come undone, ROK Straps have a loop sewn in each end. you pass the buckle around your frame, rack or other secure point and then back through the loop in the end making for a very secure mount. With each end secured, connect the buckle in the middle and simply tug the slack end of the strap until your load is firmly held in place.
The Motorcycle Adjustable Strap is 1 inch wide and adjusts in length from 18 to 60 inches.
Rated to carry 100 lb (200 lb burst strength)
Designed specifically for motorcycle and ATV use.
Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.
The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary har
Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets and that will be no problem. See bottom image.
Note: Placement of this top rack does require removal of the stock tool bag.
This kit fits all Nomadic tubular type racks. (All flat stock racks are already RotoPax compatible)
The second image shows the kit, which includes all the hardware and instructions required. The lower image is just an example of what the eXpander looks like mounted to one of their racks.
Hand built aluminum luggage rack from the B&B Off Road Engineering folks down under. This unit really is a beauty to look at and extremely rugged, made from 4mm 5083 aluminum plate! Tie down whatever you need with confidence. Whether it's your books to get to school or a bag to get across the country, no worries mate. Available in either bare polished aluminum or with a black polymer coating.
While plenty rugged to use as grab handles, you can keep your stock handles if you so desire. All necessary stainless clamps and bolts are provided.
If you want a wider platform for support, consider adding the luggage plate to this rack.
Bike must have the DR250 Taillight installed to work with this rack.It will not work with the stock USA taillight.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready!
This is the ENDURO Series DR650 rear rack which measures 10 inches wide and 12 inches long.
The Bajaworx Dakar Clear windshield for the KLR650 is designed to direct the wind over even the tallest of riders without compromising visibility. Decreased wind noise, reduced buffeting and more control in strong crosswinds make this a fantastic addition to your newer KLR.
Transform your ride. MadStad's patented mounting system allows riders to adjust the height and angle of their motorcycle windshield resulting in much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide. Better still, this dual-sport version pivots the shield down and forward to get it out of your way for off-road riding!
What's included in the kit:
Their complete bolt-on system is custom-made for your bike and includes everything needed to mount and position the shield. Your bike will not require any modification.
The MadStad brackets bolt to the top of your fork clamps and are completely free of the handlebars. You can adjust the shield for the optimum height, angle and airflow for comfortable street and highway riding. When going off-road you can leave your comfort adjustment as-is and pivot the entire system down and forward in front of the headlight so you can get it out of your face completely. When it comes time to hit the pavement again, simply pivot it back up and you are back in street riding comfort mode.
Parabellum LTD. has continued the highly demanded Rally Shield line by fitting up the 1993-present Honda XR650L. This is an upright Dakar Rally inspired shield, designed to protect the rider without interfering with off-road riding. For on-road riding the Rally shield protects the rider’s chest from fatiguing air blasts while keeping the head in clean air. Duck behind it in the cold or the rain to keep from experiencing the brunt of the elements. During off-road riding the Rally windshield protects the rider from mud, dust, roots, rocks, or branches without becoming invasive. Whether standing on the pegs or ducking behind it, you will be impressed at the protection it offers. Their Rally shields have been tested in the toughest conditions including an entire SORCS hare scramble season.
*The Rally shield for the XR650L is 12.5 inches tall 12.5 inches wide at the bottom and 8.5 inches wide at the top and is made from military grade 1/8 inch cast acrylic.
The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.
Mounting is accomplished by drilling two holes on each side of your headlight cowl using the provided template. 13.5 inches tall, 11.5 inches wide at the bottom, and 8.5 inches wide at the top. Made from military aircraft grade cast acrylic.
The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.
This windscreen mounts securely to the three stock windshield holes as well as the two side cowling mounts. The shield is 14 inches tall, 13 inches wide at the bottom narrowing to 11 inches at the top. Made from 3/16" military aircraft grade cast acrylic.
This is an upright Dakar Rally inspired shield designed to protect the rider without interfering with off-road riding. For on-road riding the Rally shield protects the rider’s chest from fatiguing air blasts while keeping the head in clean air. Duck behind it in the cold or the rain to keep from experiencing the brunt of the elements. During off-road riding the Rally windshield protects the rider from any amount of mud, dust, roots, rocks, or branches without becoming invasive. The Rally shield for the XT250 is 13 inches tall
11 inches wide at the bottom and 8.5 inches wide at the top. Made from military grade 1/8 inch Cast Acrylic, available in clear or tint.
New replacement side panels specifically made for TW200.
Sold in pairs, designed to be used with Maier USA Rear Fender.
Quality replacement headlight fairing for Gen 1 KLR650.
Available in 4 colors.
This optically clear headlight guard is CNC cut for a perfect fit. It is made of durable aircraft grade 3/16" thick cast acrylic which resists harsh rock impacts, trail scuffs, and incidental scratches. Velcro fasteners hold the guard firmly in place and allow for easy on & off should it need an occasional cleaning. Installation is a quick five minute job, positioning template included.
Heavy Duty replacement Voltage Regulator. More robust, but lower cost than the factory unit.
The Shorai LFM Duration Recommendation is the best overall pick for most applications, and has been selected to give strong cranking performance and long lifespan.
Measures 4.45" x 3.5" x 2.28"
Weight (lbs): 1.52 lbs
Weight (kg): 0.69 kg
Cold Cranking Amps: 210
Polarity: [- +]
Each Shorai battery includes self-adhesive foam panels to achieve a snug fit in your battery box.
New wider seat to help keep comfortable on that long commute or dual sport ride. The added width and foam density will help keep the seat from being an item to stop you from going on that ride or enjoying the bike.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
| Width: | 10.5" (267mm) |
| Height: | Same as OEM |
State-of-the-art replacement seats, Sargent seats are built on a percision-molded lightweight Polytec seat pan. Sargent's proprietary seat foam (Super Cell Atomic Foam) is their own unique blend of resilience, firmness, and vibration-absorption qualities, making it well suited for long distance comfort and support. Sargent seats are covered in a marine-grade, UV-stablized mildew resistant CarbonFX vinyl. Available in standard height and 1" lower than stock. These seats will fit bikes with the stock, IMS, or any other aftermarket fuel tank.
| Width: | 11" (279mm) |
| Height: | Same as OEM |
This kit includes a DOT LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
How does this headlight compare to our original TW200 kit? First and foremost, this kit has SAE/DOT markings and a much wider/brighter high beam pattern. The low beam is very similar to our original kit: wide, flat, and bright but with more punch. The DOT headlight assembly has also proven to be more durable than the original headlight.
Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Approved
CE, RoHS, ISO9002, IP67
No cutting, drilling, or wiring modifications! Installation takes 5 minutes.
Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.
Please note that this product is not compatible with the 1987 TW200.
Pivot Pegz have set a new standard in foot peg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best foot pegs in the world and they really do perform as good as they look. There's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option.
Wider foot pegs for sure-footed comfort.
17-4 cast stainless steel.
| Width | 1.97" |
| Length | 3.18" |
Pivot Pegz have set a new standard in footpeg performance and quality, and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
See below for extenders for these pegs to make them true ADV pegs!
If you are replacing your side stand you will want to check the hardware. Over the years they can take a beating and the springs become lost or broken.
This is the full kit that includes #4, #5, #2, and #3 in the diagram.
Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.
This set of high quality replacement steering stem bearings includes:
Each pattern is available in three advanced synthetic rubber compounds. This means you can have the optimum combination of strength, tackiness and shock absorption to suit every riding condition and individual style. Soft grip is extremely soft, giving you a very comfortable ride, great feel and reduces the chance of blisters; however, because the grip is so soft, it wears quickly. Medium is a compromise between firm and soft. Firm grip has the same feel as a stock grip, it is very strong and has very good resistance to tearing and abrasion. Half Waffle has waffle pattern in finger area for traction and diamond pattern on palm side to reduce blisters. Full Waffle: designed after the CR Honda® grip.
The plastic fitting that secures the stock choke cable to the carburetor is delicate and easily broken. A broken fitting can cause hard to solve idling and running problems.
CNC machined from billet aluminum and anodized black or blue. If you want to retain your handlebar mounted choke this may be the solution.
These no longer fit the new version of the ProCycle Remote Choke Cable. Will not work with the long or short reach choke knobs.
Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes fork seals and dust wipers.
The complete fork upgrade kit - your choice of springs and Race Tech Gold Valves. Also includes a set of top quality fork seals and 5W fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
You can select from various straight rate springs to customize the package to your needs.
Stock Spring Rate for XR650L: 0.44 kg/mm
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 2 |
An upright Dakar Rally inspired shield designed to protect the rider without interfering with off-road riding. For on-road riding the Rally shield protects the rider’s core from fatiguing air blasts while keeping the head in clean air. Duck behind it in the cold or the rain to keep from experiencing the brunt of the elements. During off-road riding the Rally windshield protects the rider from any amount of mud, dust, roots, rocks, or branches without becoming invasive. Whether standing on the pegs or ducking behind it, you will be impressed at the protection it offers.
The Rally shield for the TW200 is 13 inches tall, 12.5 inches wide at the bottom, 9 inches wide at the top, and made from military grade 1/8 inch cast acrylic in either clear or tint.
Genuine Suzuki Factory Service Manual for the DR200.
Replace these any time you feel excessive play in the sprocket hub.
Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.
Sold as a full set.
The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike.
Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.
Available in 2 colors
Here is the little switch that mounts inside your brake or clutch lever perch and controls the brake light or clutch safety circuit. This switch often gets damaged in an unplanned dismount (aka: crash) or the plastic simply cracks from age. When this happens, you can find yourself chasing a short circuit that keeps blowing your fuse every time the brakes are applied. If this has happened to your TW, here's the fix!
Maxima light viscosity 3w 75-390 shock oil, 1 US Quart.
The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels.
Ride in warm temperatures a lot? Worried about your motor oil just getting too hot? The Trail Tech Universal Fan Kit mounts up to the backside of the DR's oil cooler to draw cool air across it and keep those oil temps down. An electronic temperature sensor mounts to the fan, no need to cut any fluid lines, and automatically turns the fan on when needed to keep the temperature in the optimum range.
The activation sensor can be set wherever you like to keep the temperature right where you want it. Backlit for easy viewing anytime it also includes a volt meter.
Kit Contents
A six step maintenance system designed to recharge any K&N air filter.
Quick release one-piece clamps that saves space. These are great for fuel lines, controlling wires, and can be used many times.
Comes with 4 each of 8mm, 9mm 10mm, and 12mm.
No special tools needed, from Helix Racing.
