Search Products

Shinko's REFLECTOR side wall technology to the popular E804/E805 Adventure Trail tires. Almost completely unnoticeable until light hits the reflective material on the sidewall and then boom ...the sidewall of the Reflector tire lights up. Be Safe. Be Seen.

• Same outstanding performance as the standard E804/E805 with added safety in mind
• Reflective material is built into the sidewall of the tire
• The only ADV tire on the market with a reflective sidewall
• Designed as a 40% On-Road 60% Off-Road tire
• DOT approved
• M+S = Mud and Snow Rated

Tires listed are all standard Bias Ply tires unless noted with an -R after the size.

Note:Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.

Made for the true adventure rider, the K784 has everything you need to get you anywhere on or Off-Road.

• Tread pattern providing high traction on a variety of terrain
• Large tread blocks for improved tread wear and high speed handling
• High impact, Bias ply, casing structure providing a high level of puncture resistance
• Bias belted casing for improved handling & stability
• Rubber compound designed specifically for wet-slick & dry-hard packed terrain
• Picture provided for purpose of viewing treads.

Ride in warm temperatures a lot? Worried about your motor oil just getting too hot? The Trail Tech Universal Fan Kit mounts up to the backside of the DR's oil cooler to draw cool air across it and keep those oil temps down. An electronic temperature sensor mounts to the fan, no need to cut any fluid lines, and automatically turns the fan on when needed to keep the temperature in the optimum range.

The activation sensor can be set wherever you like to keep the temperature right where you want it. Backlit for easy viewing anytime it also includes a volt meter.

Kit Contents

• 4 inch SPAL fan
• TTV Temp Meter
• Temperature Sensor
• Complete Wire Harness

High Quality chain. Will need to be cut to fit your sprocket combination.

These quality sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

This kit will replace your stock sprocket bolts and nuts with new hardware.

Factory Honda replacements in a convenient kit.

Premium quality EBC Rear brake shoes.

• EBC brake shoes are radius ground, and edge trimmed
• Lead out chamfers at lining ends

• Front pads: Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Rear shoes: Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand.

Includes pads for both front and rear.

Small Wheel models have a 17" Front Wheel and 14" Rear Wheel.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand.

Includes pads for front and rear

Big Wheel models have a 19" Front Wheel and 16" Rear Wheel.

Sintered Pads from EBC are the best pads we have found for the KLR, they provide good performance in all conditions yet still give you long pad life.

These sets include front and rear brake pads.

All the parts you need to freshen up your rear brake caliper. New piston seals, slide pin and boots. Fix that sticky or limp rear brake.

• Kits contain all parts needed to re-seal leaking master cylinders
• Includes cup seals, copper washers, o-rings and replacement screws where applicable

It may not surprise you that they are covered with HippoSkin™, their waterproof outer shell, and insulated with a generous layer of HippoFat™, a warm, flexible, closed cell foam insulation—both are designed to keep inclement weather away from your hands.

Sold in pairs.

Hand/brush guards are required for proper fitment and for safety reasons.

Hippo Hands go on and off in seconds and never require tools or hardware.

These handguards come with mounts that will work on both standard and and oversize bars. The aluminum wrap-around bar is the biggest on the market with two large plastic shields that are also some of the largest available. The X-Factor hand guards offer great protection from the elements, especially during those colder months when you're trying to stretch out your riding season.

Works with 7/8" or 1-1/8" bars.

X-Factor guards may require you to cut your lever ends down, or use short levers.

Safeguard your Yamaha XT250 with T-Rex Racing's premium engine guard crash cages designed for serious off-road protection. These heavy-duty steel crash bars create a protective barrier around your engine and frame, preventing costly damage from drops, crashes, and trail obstacles. 

Custom-engineered for XT250 models, these bolt-on engine guards feature powder-coated finish for corrosion resistance and maintain ground clearance for optimal performance. 

Includes all mounting hardware. Essential protection for adventure riders, trail enthusiasts, and dual-sport motorcyclists who demand reliable crash protection for their Yamaha bike.

PSR has a new shark fin rear rotor protector for the big XR and XRL. CNC machined from forged aluminum and then anodized gun metal in color. This unit bolts to the stock caliper bracket.

Bradley performance bomb header for TW200. 

By positioning this “Bomb” at a key point in the system, increased performance and flow is achieved through the expansion and contraction of exhaust sonics through the system. The result is a flow increase of nearly 10%. 

The outer chamber in the Powerbomb allows the air to expand, cool and ramp back up at a higher velocity. 

Fits all years of TW200 and works with all other brands of mufflers. Stainless steel and nickel plated. A clamp-on shield can be added, sold separately.

This is a new gasket for the cylinder head - head pipe junction. Installing a new one with your new header will ensure a good seal and no exhaust leak.

The EVO R series draws on our rich heritage of making power. Offered for various off road MX and sport ATV models, the EVO R is a tried-and-true series that will save weight, add noticeable performance gains and sound tremendously better than stock.

• Hard anodized oval shaped aluminum muffler
• TIG welded reinforced muffler bracket(s)
• 304 stainless steel mid pipe / head pipe
• Red powder coated stainless steel end tip
• Lighter than stock exhaust system
• Huge horsepower and torque gains
• Sleek muffler design allows for maximum clearance
• Removable screen-type spark arrestor included
• Handmade in the USA
• 1 Year Limited Manufacturer’s Warranty

TW200 billet oil drain cap plug. 

Nice billet aluminum replacement for the old cast oil drain cap.

This is all you need to not only change your oil, but protect your motor as well. We include a billet oil drain plug cap, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

• Billet Oil Drain Plug Cap
• O-Ring Kit
• 5-Pack of Oil Filters

Replace your worn out clutch with a high quality Clutch Kit. This kit includes new friction discs for your clutch pack.

Please note: kit includes friction discs only, steel plates and springs not included.

Kit includes hardened steel bushing, an upgraded seal, an O-ring and lock washer.

A head gasket and base gasket to fit the Big Bore cylinder.

• Direct bolt-on, ready-to-install cylinder; requires no replating and looks virtually identical to the OEM
• Nickel Silicon Carbide plated for long life
• Honed to exact size for easy piston installation
• Big bore cylinders do not require any machine work
• Come complete with gaskets, cylinder, 94mm piston, rings, pin and clips

Designed to enhance mid-range and top-end power. Manufactured using the highest quality standards. No core required.

Note: This camshaft has been designed to work with the OEM Yamaha piston, or the BBR big bore kit piston, with OEM sized valves. Any other combination of parts will require that you manually check valve to piston clearance.

The ultimate Adventure peg, from the folks at Fastway - Pro Moto Billet. This peg is big enough to stand on all day with no fatigue, it measures 2.25" front to back and is 4.75" wide.

In addition to the big size, you can also adjust the camber with their patented FKMS Kamber bolt. ´Tilt´ your pegs to increase comfort, or to give better squeeze on your bike. You can further customize them with 3 styles of patented adjustable threaded cleats. Take your traction from comfortable to gnarly. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long.

These Adventure pegs are offered in several colors, but some colors may require extra time, call for availability.

Mounting these pegs to your KLR takes just a bit of work.

Please see link to the instructions below. These apply to the ADV and Evolution AIR Peg as well as the Evolution II pegs referred to in the instructions.

Finally, the ultimate Adventure peg, from the folks at Fastway - Pro Moto Billet. This peg is big enough to stand on all day with no fatigue, it measures 2.25" front to back and is 4.75" wide.

In addition to the big size, you can also adjust the camber with their patented FKMS Kamber bolt. ´Tilt´ your pegs to increase comfort, or to give better squeeze on your bike. You can further customize them with 3 styles of patented adjustable threaded cleats. Take your traction from comfortable to gnarly. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long. You can also order serrated (F5 - bottom left image) or spiked (F6 - bottom right image) cleats separately.

These Adventure pegs are offered in several colors, but some colors may require extra time, call for availability.

Fastway offers a large ADV peg that is 4.75" long and 2.25" wide. With these pegs you can adjust the camber with their patented FKMS Kamber bolt. ´Tilt´ your pegs to increase comfort, or to give better squeeze on your bike. These pegs come with two sets of F3 cleats (one standard, one long). You can order serrated or spiked cleats separately.

These Adventure pegs are offered in several colors, but some colors may require extra time, call for availability.

These low peg mounts will drop your footpegs 1.5" and move them to the rear 1" for a much more comfortable riding position, especially for taller riders. Unlike relocation plates, these mounts do not hang dangerously below the frame. You can mount stock or aftermarket pegs and they are compatible with all skid plates, crash bars, and center stands.

New 10.9 high strength mounting bolts are included. Once installed the foot controls will need adjustment and the brake switch spring will need to be slightly modified.

Get better range from your XR650L by adding a Clarke 4.7 gallon fuel tank. Cannot use stock shrouds.

Available in Natural, White, Black, and Red. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap, uses stock petcock.

Acerbis 3.9 gal tank adds function and great looks to your DRZ. This high capacity fuel tank incorporates modern lines and high quality construction that can't be beat. Includes gas cap, petcock and all mounting hardware.

The new 4.1 gallon fuel tank from Clarke. Carries almost 2 more gallons than the stock tank. Available in Blue, Black, Silver, White or Natural

More range at a great price.

The 3.6 gallon tank is for the off-road DRZ400 and DRZ400E.

The 3.9 gallon tank for the dual-sport DRZ400S. The 3.9 gal tank also fits the ES and SM models.

Both tanks are available in a selection of colors.

NOTE: Clarke tanks do not come with a vent hose or vent cap.

You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of a big tank? The 3.7 gallon tank from Clarke might be just right. It's almost 5 lbs lighter and holds close to 1/2 gallon more fuel than stock to increase your range by about 20 miles. Fits with your stock petcock, Pingel or Raptor petcock.

We worked with TechSpec to have them make custom tank grip pads that look great on the IMS TW tank. These pads not only cover those ugly scuffs, but give great knee grip to the slippery plastic.

Designed to fit IMS 3.6 gallon tank only.

Clear lens, amber LED type lights. Short flexible stems. Very small, only 2 7/8" long. Requires a LED turn signal flasher to flash properly. 4 Pack

These signals have short rubberized flexible stems and bright mini halogen bulbs.

• Ministalk Marker Light V-Shape - Black/Amber
• Size:  2-5/8"
• Single-filament bulbs
• Sold in pairs

This relay will fix your flash rate problem caused by aftermarket signal lights and/or integrated tail light. If your signal lights flash too fast or do not flash, this part is your solution! Plug and play - easy installation.

Only ONE relay is needed per motorcycle regardless of front and rear signal set-up.

• Slows signaling flash rate back to the normal rate when your bike goes into hyperflash state (or your signals stay on constantly)
• Adjustable functionality to speed up or slow down flash rate to your preference
• Plug and play installation: simply replaces the relay already on your bike
• Fits like OEM
• Relay housing is flexible so that you can access the adjustment dial inside the unit

This component works with the following signal configurations:

1. All stock
2. Stock taillight, aftermarket signals
3. Integrated taillight, stock signals
4. Integrated taillight, aftermarket signals.

The relay comes preset to 85 cycles per minute. You can alter the flash rate to make it faster or slower. If you slip off the grey cover you can access an adjuster that will enable you to change the flash rate to your liking.

Please make sure your bike uses a 2-pin relay for the signaling system. If your bike has hazard lights it may need the 4-pin relay. Please also note the pin configuration and make sure it matches what is on your bike. It is very important to verify fitment before making your purchase.

Reproductions of the original DR650 factory turn signals. Save a bundle compared to the $70+ each cost of the OEM signals. The wire pigtails plug directly into the factory harness. No cutting or splicing necessary. Choose original style amber lens or clear lens with amber bulb.

The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.

You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.

Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.

There are many options and configurations using this electronic tool.

No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.

This heavy duty aluminum bracket is specifically designed for mounting auxiliary LED lights to the front of your XR650L without interfering with your large aftermarket fuel tank.  If your bike needs improved lighting this mount is the best place to start!

– 0.190″ 5052 Aluminum
– Laser cut
– CNC formed
– Powder coated black
– Includes stainless mounting hardware and JNS stickers.

LED auxiliary lights are sold separate.

This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a plug and play installation however a small amount of trimming on the backside of the plastic headlight shroud is required.

This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive). The high beam is amazingly bright eliminating the need for auxiliary lighting.

The materials, construction, and aesthetics are all top notch. You won’t be disappointed.

Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive

This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.

Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.

The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary har

Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets and that will be no problem. See bottom image.

Note: Placement of this top rack does require removal of the stock tool bag.

CycleRacks are made out of steel tubing, bent in a press, and welded together in a jig. All of their racks have the same platform, 18" wide by 12" deep. Includes lower mount hardware.

All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.

The Front Rack gives a lot of options for functionality.

CycleRacks are made out of Schedule 40 11/16 black steel pipe, bent in a press, and welded together in a jig.

All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.

This Trekker Top Case is manufactured from glass fiber reinforce polymers ensures high structural rigidity. An anodized aluminum cover is then placed over that to resist weathering. 52 liters in size, there is enough room for 2 helmets. Attaches to your favorite rack with a Monokey fixing system. Available in Aluminum or Matte Black.

• Dimensions: 23.6"L x 18.1"W x 12.4"H
• Volume: 52 Liter
• Max Load: 22 lbs.
• Helmet Capacity: 2
• Weight: 11.44 lbs.
• Color: Brushed Aluminum / Matte Black
• Material: Polypropylene / Aluminum

The Bag Snake kit works great for rear bags and side bags. When rigged with a side bag the second ring on the ring tensioner creates a secondary buckle so you can loosen the top for access and your bag doesn't fall away from the bike.

When rigged for a rear bag the diagonal section of the strap prevents any slippage over the ends of the bag. For this reason, the Bag Snake is great for smaller rear bags.

Kit Includes:

• 1 Heavy Duty Cam Tension Loop
• 1 Heavy Duty Metal Ring Tension Loop
• 1 Six Foot Runner Loop
• 1 Heavy Duty Metal Ring Loop

This optically clear headlight guard is CNC cut for a perfect fit on your XT250 headlight lens. 

It is made of durable aircraft grade 3/16" thick cast acrylic which resists harsh rock impacts, trail scuffs, and incidental scratches. 

Velcro fasteners hold the guard firmly in place and allow for easy on & off should it need an occasional cleaning. Installation is a quick five minute job, positioning template included.

• Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life
• Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material
• Triple-lip seal design
• Dyno-tested to last 3 to 4 times longer than OEM seals
• Directional ribs allow seal to be installed easily
• Kits include fork seals and dust wipers

Includes all components needed to rebuild you forks.

• Inner and outer bushings
• Oil and dust seals
• All necessary o-rings

Rebuild kit bearings are made using 52100 bearing steel

Included in this kit are fork springs, Cogent DDC (Drop in Damper Cartridge) performance cartridges and three bottles of 5w fork oil. Refresh those tired old forks and make them better than new. These DDCs from Cogent are easy to install. No taking the forks apart, no drilling of the damping rods, nothing. Just take them off, flip them over to drain the oil, add new 5w oil, drop in the DDCs and then add the springs and spacers and then install the caps. Preload spacer material is included with the .47 and .70 springs, additional spacers are not needed with the other kits.
This upgrade offers better control off-road as well as on. Less brake dive keeps the fork up in the middle of the stroke on-road and better control off-road whether it be rolling water bars or bouncing off the rocks.

• Rider and Gear up to 160lb. = 0.47 springs → 24% stiffer than stock
• Rider and Gear 160-225 lb. = 0.52 springs → 39% stiffer than stock
• Rider and Gear 225-275 lb. = 0.58 springs → 56% stiffer than stock
• Rider and Gear 275-325 lb. = 0.63 springs → 66% stiffer than stock
• Rider and Gear 325 lb.-UP = 0.70 springs → 84% stiffer than stock

This complete fork upgrade kit includes stiffer fork springs and Race Tech cartridge emulators, as well as a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.

You can select from various straight rate springs to customize the package to your needs.

• Rider and Gear up to 160lb. = 0.47 springs → 24% stiffer than stock
• Rider and Gear 160-225 lb. = 0.52 springs → 39% stiffer than stock
• Rider and Gear 255-275 lb. = 0.58 springs → 56% stiffer than stock
• Rider and Gear 275-325 lb. = 0.63 springs → 66% stiffer than stock
• Rider and Gear 325 lb.-UP = 0.70 springs → 84% stiffer than stock

Lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.

• Rider and Gear up to 145 lb. = 0.47 springs → 24% stiffer than stock
• Rider and Gear 145-185 lb. = 0.52 springs → 39% stiffer than stock
• Rider and Gear 185-235 lb. = 0.58 springs → 56% stiffer than stock
• Rider and Gear 235-285 lb. = 0.63 springs → 66% stiffer than stock
• Rider and Gear 290 lb.-UP = 0.70 springs → 84% stiffer than stock

The complete fork upgrade kit - your choice of springs and Race Tech Gold Valves. Also includes a set of top quality fork seals and 5W fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.

You can select from various straight rate springs to customize the package to your needs.

Stock Spring Rate for XR650L: 0.44 kg/mm

Race Tech Hi-Performance Fork Spring have the highest stiffness-to-mass ratio in the industry. This means they are lightweight for their particular rate. These spring designs have taken years of manufacturing experience. They require the finest materials and processes.

Race Tech Hi-Performance Springs have extremely accurate rates. They are heat-treated, shot-peened and preset so they cannot sack out.

OEM spring rate is 0.42kg/mm. 

The progressive factory springs are well known to be way to soft for most riders. Cogent Dynamics straight rate springs will give better control in the rough stuff and when loaded up.

Sold in pairs.

0.72kg/mm riders up to 260lbs

0.80kg/mm riders 260lbs and up

The 0.72 springs are 28% stiffer than stock and will be a great choice for most riders

Not compatible with Adventure Sport ES

Don't want to buy a new shock? This rebuild makes the stock shock about 10 times better. Cogent Dynamics takes a stock DR650 shock, tears it down, cleans it up, adds a hard ceramic coating, then rebuilds it with a completely new Shock Shaft Assembly with rebound damping adjustment.

Any aftermarket spring for your stock shock will fit on this shock. If you are currently using the original spring, you will want to order a stiffer spring to go with your new shock. 

Our 7.5 kg/mm rear spring is 16% stiffer than the stock one and is perfect for the majority of riders. If you are a larger rider, or carry a lot of gear or a passenger (total weight exceeding 250 pounds) you will probably want the 8.3 kg/mm rear spring which is 28% stiffer than stock.

This shock includes the Bling Ring preload adjusting ring AND the Thrust Bearing! This replaces the two stock preload/lock rings. This ring is CNC machined aluminum with the additional thickness to provide superior support on the shock body.

Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.

Cogent Dynamics takes a stock DR650 shock, tears it down, cleans it up, adds a hard ceramic coating, then rebuilds it with a completely new custom shim stack that gives you excellent rear wheel control. 
This custom Cogent valve stack makes this shock behave much like the Cogent Shock Shaft without the rebound adjustment capability.  Providing a greatly improved suspension feel over stock at an affordable price.

Spring not included, sold separate. 
Recommended spring rates:

• Rider & gear up to 150 lb = Stock 6.5 spring
• Rider & gear up to 200 lb = 7.5 spring
• Rider & gear 200-275 lb = 8.3 spring
• Rider & gear 275-350 lb = 8.6 spring
• Rider & gear 350 lb & up = 9.6 spring

This shock includes the Bling Ring preload adjusting ring AND the Thrust Bearing! This replaces the two stock preload/lock rings. This ring is CNC machined aluminum with the additional thickness to provide superior support on the shock body.

The Moab shock from Cogent Dynamics will change how you feel about your KLR. You may like it now, maybe even like it a lot, but you will absolutely fall in love with it once you mount up a Moab shock.

Spring duties are handled by a custom spring available in either Standard or Heavy-Duty weights. The Standard spring will be fine if you are under 250 pounds and don't ride with luggage or passengers often. Ride heavily loaded or with a passenger regularly and you will probably want the Heavy-Duty spring.

For a true comfort and performance package, we highly recommend upgrading your front suspension at the same time.

Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids. Fits stock shock.

• 30% stiffer than stock
• Preset and stress relieved for long life
• Custom wound from aircraft quality spring steel
• Powder coated finish

Aluminum alloy lowering link. Lowers the rear suspension approximately 1 inch.

Bearings included.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

A premium billet sprocket carrier from Warp 9 Racing that houses 2 bearings to help protect against the sideways twisting load that is commonly known to prematurely wear out the bearing and cush rubbers. This wear can cause extreme failure possibly damaging the hub.

Anodized, Includes spacers already installed.
Stock sprocket bolt pattern to fit any stock compatible sprocket.

These are designed to work with Warp 9 hubs.

Rear wheel bearing kit. Includes a new dust seal and the bearing and seal for the cush drive hub. All bearings are sealed on both sides.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology.  Try the grip with the technical advantage of three dedicated rubber compounds.

• Vibrasonix pillow top reduces vibration and cushions impact. 
• Inner core compound perfects the bonding interface with bars. 
• Anti-Rip Tip™ uses denser compound to increase life of grip. 
• Designed to self-clean and shed mud away from outer surface. 
• Tacky gel-like surface compound is perfect for the trail and MX.

• Contains degree wheel, standard unit indicator, adjustable magnetic stand, and three positive stops (10 mm, 12 mm and 14 mm threads)
• Can be used to install and adjust timing of any cam
• Wooden carrying case

Convenient tool to hold the clutch basket when servicing your clutch

Repair manual for XR250R '86-'04 / XR250L '91-'96 / XR400R '96-'04.

This is a weatherproof protectant for wiring and electrical connections. Goes on as a liquid and dries to a vinyl polymer that resists dirt, dust, chemicals and moisture, ensuring that connections stay intact. Brush-top applicator allows coverage without gaps and enables access to tight spaces that roll tape and shrink tubing can't get to.

A motorcycle rectifier-regulator is a crucial part of the charging system, acting as a charging control device to prevent damage to your battery and electrical system. These OEM-style units are direct replacements, providing the proper fit and the expected performance on your bike

• Includes all necessary parts to replace OEM-style fuel mixture screw with an extended screw for easy tuning
• Kit includes extended mixture screw, O-ring, spring and washer.
   

Zero Gravity windscreens feature the finest optics of any windscreen on the market. All Zero Gravity windscreens are fabricated using highly specialized "vacuum forming" techniques similar to those used to form aircraft canopies. The result is a virtually distortion free optical lens.

Made from the finest grade of acrylic plastic, Zero Gravity windscreens are stretched as they are formed, a process which results in superior strength and flexibility. This flexibility allows the windscreen to absorb road vibrations and resist cracking. All of our windscreens are factory pre-drilled and ready to install. The mounting holes and windscreen profile match the O.E.M. windscreen for a precision fit.

Zero Gravity currently offers three types of windscreens for the new version of the KLR.

SR is the Stock Replacement

DB is the Double Bubble screen

ST is the Sport Touring model.

The DB model is approximately 1.75 inches taller than stock and the ST is approximately 3.5 inches taller than the original. Each screen is available in Clear, Smoke or Dark Smoke colors as well.

Add long distance comfort to your street legal dual purpose Suzuki DRZ400S with a lightweight, easy bolt-on installation (4 bolts), custom tailored Parabellum windshield. NO drilling required. 

The smooth slender design gives quiet wind protection with good looks and 16% less aerodynamic drag for improved gas mileage and speed. 

This windshield measures 20 inches, 22 inches or 24 inches. Those measurements are from the top of the headlight to the top of the shield. 

The windshield is made of durable, optically clear .177 inch aircraft acrylic. It is offered in clear or tint . 

At Parabellum all windshields are guaranteed for one year.

The new Touring windshield for the 2008-on Kawasaki KLR650 has been completely redesigned to both improve protection as well as appearance.

Parabellum utilizes the stock windshield screw locations with our angled brackets to mount the newly designed shield. The windshield uses stand-off technology so the shield is more upright. This allows a smaller shield to give more protection. This also keeps the top edge of the shield away from the rider when standing on the pegs and using other off-road riding techniques.

The Parabellum Touring shield for the KLR is also significantly wider and taller than the factory windshield maximizing comfort and wind protection.

The windshield measures 14.5 inches wide and is available in two heights. We recommend this windshield for those seeking maximum protection. The shield is made of 1/8 inch cast acrylic and offered in clear or tint.

The long over-due rally shield for the 2008-on KLR650 is finally here!

Parabellum uses 4 steel brackets mounted to factory locations as well as our stand-off windshield design to ensure the customer doesn’t have to drill extra holes in the cowling but still achieves that iconic upright look of the real Dakar Rally bikes.

The Rally shield protects the rider’s torso/chest from air, cold, roost, branches and bushes while leaving the rider’s head/helmet in clean air. We recommend the Rally shield for riders seeking some protection, but prefer to be off-road.

The Rally shield is made from 1/8 inch cast acrylic and is 11.5 inches wide at the bottom and 17 inches tall.

Universal off-road front fender. Must be drilled to fit your mounting bolt pattern.

Replacement front fender by Maier that will fit great on your TW200.

• All Maier bodywork is made of tough, vacuum-formed high-gloss polypropylene
• Drilling is required
• Colors are OE color matched

Note: The proper way to install this front is to install the stock fender bracket to the under side of new Maier front fender using stock screws and nuts.

Genuine Honda Factory Service Manual specifically for your CRF300L

Say goodbye to the frustration of fidgety handguard expansion plugs with Warp 9's innovative Tapped Handlebars. 

These handlebars feature ends that are plugged and tapped with an M8x1.25 threaded insert, providing a secure and reliable mounting point for all aftermarket wrap-around handguards. 

No more worrying about plugs pulling out or spinning during crashes; their robust design ensures you're good to go, even when you encounter obstacles. 

Not using handguards? No problem they've got you covered!Each set of handlebars comes with aluminum grip guards and stainless bolts, offering protection for your grips and delicate throttle tube in case of a get-off. 

Designed with an oversized 1-1/8 inch (28.6mm) clamping diameter that tapers down to 7/8 inch (22.2mm) to accommodate standard controls. Crafted from 7010 T6 aluminum tubing and featuring computer-extruded variable wall thickness, they effectively reduce vibration while enhancing overall performance and comfort. 

Note: Does not include pictured bar mounts.

These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!

The Apollo Heated Grips are designed with an integrated adjustable thumb switch, which allows them to easily fit on any kind of motorcycles on the market. The integrated thumb switch gives control to the rider to adjust the temperature level while keeping hands on the bar for a safer ride.

Its wide temperature setting range will keep the rider comfortable under the cold riding conditions.

The 5 color LED display will enhance the visual look of the heated grips and will allow the rider to quickly know at which heat level the grips are set.

This system will also detect if the battery voltage is too low and will automatically shut down the heated grips in order to make sure the rider have enough power to start the engine or use the motorcycle.

Specifications:

• Integrated thumb switch designed for easy installation and control.
• “Plug & Play” wiring connections to shorten the installation time.
• Wide temperature settings for various weather conditions.
• Low Battery Warning protection to ensure the motorcycle has enough power to start.
• 5 color LED Indicators for the rider to quickly know in which heat level the grips are set.

• The new 3rd generation Motion Pro Revolver variable rate throttle system is here!
• Innovative reel changing system lets you tailor the throttle rate to your preference and riding conditions
• 5 different reels provide perfect throttle response for any condition. Use smaller reels for slower throttle rate and larger reels for faster throttle rate. Included cam reel provides progressive throttle response preferred by some riders
• Slim REV3™ throttle housing allows more room for lever clearance and adjustment to throttle housing position
• Improved throttle stop provides greater strength and durability
• Snap together elbows makes it even easier to install and change reels
• Cable boot keeps dirt and dust out for reliable and smooth operation
• REV3™ off-road kits are compatible with the new Motion Pro DirtControl™ V2 Lock-On grips and ODI Lock-On grips
• Billet aluminum inline cable adjusters ease installation and adjustment
• Lower section of cables use 5 mm housing with PTFE liner for reduced friction, increased routing flexibility and lighter weight
• Upper section of cables use 6 mm housing to provide solid support of adjusters
• Simple to install and maintain
• Patented

Kit includes:

• REV3™ throttle assembly with throttle tube (REV3™ off-road kits include the unbreakable Titan Throttle Tube™)
• Motion Pro REV3™ black vinyl cables specifically designed for your bike
• REV3™ sportbike kits include Motion Pro RoadControl™ grips
• Four interchangeable round reels: 35 mm, 40 mm, 45 mm, 50 mm
• Progressive cam reel - Sportbike kits include road race profile cam reel (orange)

New Body Plastics available in Black, White, Carbon Fiber, Dark Blue, or Yellow.

Also, Currently Exclusive to ProCycle: Olive Green, and Desert Sand (complete kit only)

Includes Rear Fender, Side Panels, Headlight Cover, and Front Fender.

Choose a Kit with Maier Front Fender [pic1] or after market SuperMoto Fender (black or white only) [pic2].

• SuperMoto fender kit includes our High Mount Fender Bracket!

Quick release one-piece clamps that saves space. These are great for fuel lines, controlling wires, and can be used many times.

Comes with 4 each of 8mm, 9mm 10mm, and 12mm.

No special tools needed, from Helix Racing.

The MotoPressor is a compact pump unit that weighs only 1.3 pounds and fits in the palm of your hand! Measures 4"x3"x1.5"  This makes it smaller and easier to carry with you.

It includes a 8 inch long inflation hose, with a a low air loss chuck. You also get an SAE power cord that attaches to your battery and stays there, along with alligator clips with SAE connector. The Pocket Pump has an 6.5 foot power cord. All of this packs into a heavy duty neoprene pouch.

MotoPressor will inflate a 150/70/ R18 tire from 0-31psi in under 4 minutes, and is capable of pumping up to 130psi. It also features a built-in cooling fan to keep the pump at optimum operating temperature, and a check valve to check the psi by attaching your tire gauge to this valve.

The ProCycle seat was designed for both comfort and function. Our seat is built with an advanced Progressive Density Foam (Pd-F) for those long days in the saddle, and also giving you freedom to move while standing. 

The wide and sturdy seat makes long rides more comfortable. The vinyl weave helps keep you cool by letting air flow between you and the seat. The front of the seat is narrower, giving you space for your knees when you're standing, while the sides have grip so you can hold on with your knees while riding. 

We will build the seat for you in-house on a new seat pan so all you have to do is put it on and go ride. Choose the heated seat option and we will add a Seat Warmer during the build process.

• Top-quality, abrasion-resistant UltraMax™ polyester
• Hi-visibility interior to help locate small parts, such as nuts and washers
• Heavy-duty, self-fastening strap for secure closure
• Small zippered pocket to hold smaller tools, bolts or screws
• Pockets range in various sizes to fit wide range of tools
• Elastic loops to hold CO2 cartridges
• Measures 13.75" x 10.5"

For adjusting valve clearance on twin cam models. Holds valve spring collar down so adjusting pads can be removed. From Motion Pro, made from hardened alloy steel.

Use this installation tool from Cogent to be sure that your Cogent Drop-in Dynamic Cartridges are installed correctly. A strong magnet in the end holds the cartridge firmly while you lower it into your fork leg. Then slide the spring over the tool until it holds the DDC down, then gently remove the tool. That simple. Never again question if it is properly seated on the damper rod.

Works equally well for removal when you need to change your fork oil. Also works great with Race Tech Emulators.

• Restore the factory shine with a superior detailer specifically formulated for the powersports industry
• Cleans, polishes and conditions plastic, fiberglass and painted surfaces
• Also effective as a light lubricant for cables and levers
• Fresh, clean scent

The GPR v5 is the fifth generation steering damper designed for dirt bikes, adventure bikes but is also used on several of hybrid applications. Its compact and slim design allows for the damper to be mounted below the handlebars, out of harm's way, without raising the bars more than an inch. Frame mounts are machined steel or Cryogenic treated billet aluminum with stainless steel pin, and billet aluminum machined bar-mounts.

• Kit includes damper, bolt on post mount, below the bar mounting system, and complete instructions.
• Bolts onto the OEM triple clamp replacing the stock handlebar mount. Will raise the Bar height about 7/8th". Fixed position.

• Will only work with Fat Bar style (1 1/8" clamp area) handlebars and stock triple clamp.

Here is the little switch that mounts inside your brake or clutch lever perch and controls the brake light or clutch safety circuit. This switch often gets damaged in an unplanned dismount (aka: crash) or the plastic simply cracks from age. When this happens, you can find yourself chasing a short circuit that keeps blowing your fuse every time the brakes are applied. If this has happened to your TW, here's the fix!

Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.

Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.

This is the more economical alternative to eliminating the 990 Adventure airbox. Better breathing equals more power. The ITG filter kit makes air filter service a snap. It also simplifies other engine and intake maintenance chores. Our kit features a steel base plate which will not deform like plastic and does not conduct heat as much as aluminum. The white powder coating also helps reflect engine heat. To take advantage of the increased airflow, we recommend upgrading your fuel injection map with TuneEcu or a Power Commander.

• OPTION - Twin Air Breather Filter (replaces standard breather filter)

Giant Loop’s 8-liter Fandango Tank Bag provides easy access to fuel, room enough to pack gear for a day trip or a long-haul journey, and is loaded with rider-friendly features similar to its smaller counterpart, the 6-liter Diablo. With its larger capacity, the Fandango provides riders a convenient way to carry larger items such as a DSLR camera, rain gear, first-aid kit, and more.

The Fandango makes packing a breeze with its handy movable interior divider featuring elastic organizers and a spot for your tire pressure gauge. With a fully lined interior that's compatible with hook-and-loop fasteners and an exterior mesh pocket, you'll have plenty of options to keep everything neat and tidy. Plus, if the weather decides to take a turn for the worse, we include a waterproof Tank Bag Dry Pod™ to keep your sensitive gear safe from moisture!

• Harness Dimensions: 8.5″ wide X 12″ long
• Tank Bag Dimensions: rear 8″ tall, front 5″ tall, 8″ wide
• Volume: 8 liters
• 22 oz vinyl coated polyester Bomb Shell™ reinforced with foam
• Slip-Not and clear vinyl top
• Rubber electronics port
• Water resistant YKK zipper (bag)
• Beefy YKK coil zippers (harness)
• Nylike webbing
• Reflective accents for visibility