Kit includes front and rear brake pads.
EBC brake pad set.
Includes front and rear brake pads
Replace those worn out brake pads with quality EBC replacements.
SMX Carbon Look Rotor
Quality components at a great price.
All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.
Made by Nissin, an OEM supplier in Japan
A six step maintenance system designed to recharge any K&N air filter.
Evans Waterless Coolant (EWC) can be used for all water cooled motorcycles to eliminate overheating. With a boiling point in excess of 375° F, it will not vaporize, thus eliminating overheating, boil-over and after-boil. At the other end of the spectrum, EWC freezes below -40° F.
EWC also delivers more power by eliminating pre-ignition and detonation caused by overheating, thus improving combustion efficiency. It also generates very low vapor pressures which reduces strain on cooling system components. EWC comes in 1/2 gal. containers.
Installation requires specific procedures. Please refer to the instructions.
RT Ultra Slick Grease provides maximum lubrication and minimum friction for seals and bushings. Great for engine seals too.
For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.
Quality replacement parts for servicing your shock.
Kouba lowering link will lower the rear suspension 1.75". Comes with bearings and seals installed for a quick and easy installation.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Precision tolerances – The tightest in the industry. Ultra-lightweight, for reduced unsprung mass. Straight rate springs will give better control.
Sold in pairs.
The complete fork upgrade kit - Race Tech springs and emulators. Also includes a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
Precision tolerances – The tightest in the industry. Ultra-lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.
Fork brace precision machined from aluminum barstock. Drilled and tapped for optional lower fender attachment.
Hard anodized black for corrosion protection. Fits OEM forks. Split design allows for installing in minutes without having to remove the forks.
Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.
OEM spring rate is 6.7kg/mm. We offer stiffer spring rates for riders who wish to carry luggage or just prefer firmer suspension.
Race Tech shock springs require adapter collars which are included with your spring. *Spring color may vary due to specification requirement and availability.
| Shock Spring | Qty 1 |
| Spring Adapter Collar | Qty 2 |
| Spring Adapter Collar 2 | Qty 1 |
8.0 kg/mm is 24% stiffer than stock
Complete high quality kit to replace the bearing and seals in the DRZ400 shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Seal | 8 |
| Needle Bearing Shaft | 4 |
| Needle Bearing | 7 |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
The Complete Seats come assembled with an aftermarket pan and ready to ride.
"Will not fit the Rally model"
| Width: | 10 3/4" (273mm) |
| Height: | Same as OEM |
This Comfort XL seat design is roughly 3" wider overall than their standard comfort seat. This means more surface area, better weight distribution, and added comfort for those not worried about seat width.
Available as Complete Seat only. The Complete Seats come assembled with an aftermarket pan and ready to ride.
| Width: | 11" (279mm) |
| Height: | Same as OEM |
Seat Concepts new wider seat to helps keep you comfortable on those long commutes or Dual-Sport rides. The added width and foam density will help keep the seat from being the item to stop you from going on that ride or enjoying the bike.
The new updated 2.0 version has a sleeker shape and a better fit in the tank area.
Complete Seats come assembled on an high quality aftermarket pan and ready to ride.
| Width: | 8" (203mm) |
| Height: | Same as OEM |
New wider seat to help keep comfortable on that long commute or dual sport ride. The added width and foam density will help keep the seat from being an item to stop you from going on that ride or enjoying the bike.
The new updated 2.0 version has a sleeker shape and a better fit in the tank area.
Complete Seats come assembled on an aftermarket pan and ready to ride.
| Width: | 9 1/8" (232mm) |
| Height: | 1" (25mm) Lower than stock |
Provide protection for your motorcycle’s front brake and clutch levers with Barkbusters aluminum bar lever protection handguards. Designed specifically for the Royal Enfield Himalayan, these guards feature heat treated full wrap aluminum backbones that mount at two points on each side for strength. Prevent costly damage to your motorcycle with Barkbusters aluminum bar lever protection handguards.
Features:
NOTE: Not compatible with Royal Enfield braced handlebar.
Add Plastic Handguards for a complete kit.
Maximize your wind protection with Barkbusters' largest handguard plastic! For use with single sided Storm mount and all Barkbusters backbone handguards
Provide protection for your motorcycle’s front brake and clutch levers with Barkbusters aluminum bar lever protection handguards. Designed specifically for the Tenere 700, these guards feature heat treated full wrap aluminum backbones that mount at two points on each side for strength. Prevent costly damage to your motorcycle with Barkbusters aluminum bar lever protection handguards.
Features:
Add Plastic Handguards for a complete kit.
Protect your motorcycle's levers from damage during an impact with the solid protection offered by Barkbusters aluminum bar lever protection handguards. Constructed with solid, heat treated aluminum backbones, these hand protectors use a two point mounting system that provides strength to withstand plenty of force. Motorcycle handguards by Barkbusters with their full wrap design, will help keep your levers operational and your ride from coming to a premature end in the event of a drop or other mishap.
Features:
Add Plastic Handguards for a complete kit.
Protect your motorcycle's levers from damage during an impact with the solid protection offered by Barkbusters aluminum bar lever protection handguards. Constructed with solid, heat treated aluminum backbones, these hand protectors use a two point mounting system that provides strength to withstand plenty of force. Motorcycle handguards by Barkbusters with their full wrap design, will help keep your levers operational and your ride from coming to a premature end in the event of a drop or other mishap.
Features:
Add Plastic Handguards for a complete kit.
Provide protection for your motorcycle’s front brake and clutch levers with Barkbusters aluminum bar lever protection handguards. Model Specific, these guards feature heat treated full wrap aluminum backbones that mount at two points on each side for strength. Prevent costly damage to your motorcycle with Barkbusters aluminum bar lever protection handguards.
Features:
Add Plastic Handguards for a complete kit.
Provide protection for your motorcycle’s front brake and clutch levers with Barkbusters aluminum bar lever protection handguards. Model Specific, these guards feature heat treated full wrap aluminum backbones that mount at two points on each side for strength. Prevent costly damage to your motorcycle with Barkbusters aluminum bar lever protection handguards.
Features:
Add Plastic Handguards for a complete kit.
Provide protection for your motorcycle’s front brake and clutch levers with Barkbusters aluminum bar lever protection handguards. Model Specific, these guards feature heat treated full wrap aluminum backbones that mount at two points on each side for strength. Prevent costly damage to your motorcycle with Barkbusters aluminum bar lever protection handguards.
Features:
Add Plastic Handguards for a complete kit.
To be fitted to the top of the Barkbuster EGO handguard.
Weight:
360 grams/pair or
180 grams/each
Fitment Notes: If you have a hardware kit listed below see special fitting notes as additional parts may be required
BHG-010 Requires two additional M6x40mm countersunk bolts
BHG-032 R1200GS/A requires two additional M8x55mm countersunk bolts
BHG-045 G650GS requires two additional M6x65mm countersunk bolts
BHG-050 Will not fit
BHG-051 Requires two additional M6x50mm countersunk bolts
BHG-059 Tiger XC, XCA & XCX (all ’15 on) use M6x45mm bolt from BHG-059 kit
BHG-075 Will not fit
BHG-079 Will not fit
Extend your comfortable riding season with Barkbusters BBZ cold weather protection handguards. Designed to fit with or without existing Barkbusters backbones or handlebar weights, these guards offer superb wind protection without limiting access to your grips or controls. Simple to install, they can be mounted or removed within ten minutes without permanent modifications. Ride with less bulky gloves in colder weather with the Barkbusters BBZ cold weather protection handguards.
Features:
Whats in the box:
Mount Barkbusters standard aluminum bar handguards to 1-1/8" motorcycle handlebars with the Barkbusters Tapered handlebar saddle clamp set.
What's in the box:
These are all you need to mount your current Barkbusters Handguards when you upgrade to a tapered oversized 1 1/8" handlebar.
For Tapered 1 1/8" Handlebar
Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.
Features:
What's in the box:
Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.
NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar
For straight 7/8" handlebar
Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.
Features:
What's in the box:
Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.
The X-Factory Handguards from Acerbis are designed with a steel bar encased in an injection-molded Nylon composite. A replaceable dual-injected polypropylene shield attaches to the bar, providing excellent protection against debris and harsh conditions.
Included with the handguards is a universal mount kit, enabling installation on either 7/8" or 1 1/8" handlebars.
Will not fit XT250 with stock handlebars (oversize bars ok). Recommend Acerbis Rally Pro X-Strong to clear master cylinder.
New design gives you more protection and uses OEM mounting points for easy installation.
The Honda CRF1000L Twin Dakar Bash plate. Our all new engine protection system is designed to provide all the benefits of a lower crash bar and bash plate in one. It is constructed from 4mm & 5mm 5083 structural plate combined with 20mm heavy wall alloy tubing to form the outer profile. It is mounted in seven locations to make it the most rigid bash plate on the market. It has a narrower profile and fewer snag points than the conventional crash bars. Available in polished or black powder coat.
Fitment notes:
Their best selling product to protect your bike, Flatland Racing skid plates are made from 5052 3/16" aluminum plate.
They are all hand tig welded together with side engine guards. Installation is easy with our clamps that grip tight.
Their skid plates offer clean out slots and oil plug hole, making oil changes simple. These are more durable than carbon fiber and plastic.
Mounting hardware and instructions included.
Note: Will not fit the CRF300L Rally
Their best selling product to protect your bike, Flatland Racing skid plates are made from 5052 3/16" aluminum plate.
They are all hand tig welded together with side engine guards. Installation is easy with our clamps that grip tight.
Their skid plates offer clean out slots and oil plug hole, making oil changes simple. These are more durable than carbon fiber and plastic.
Mounting hardware and instructions included.
For CA models, Flatland can modify your skid plate UPON REQUEST to fit around the canister. Please allow 3 extra days for shipping if not in stock.
Enjoy maximum protection and durability with an SW-MOTECH skid plate. Fully welded aluminum construction is engineered in Germany to provide proper protection from impacts, abrasions and projectile debris. Multiple ventilation slots on the front, sides and bottom of the skid plate permit maximum air-flow to keep your motor cool. Drilling, cutting, welding or any other permanent modifications are not required.
Features:
What's in the box:
This kit provides some much needed protection for both you and your big DR. Handguards and deflectors protect your hands while the skid plate and Case Armor will cover your baby's soft externals.
Protect your frame/paint from scuffs and scratches with frame guards. The DR 250 & DR 350 frame guards are made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.
The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike.
Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.
Available in 2 colors
Protect your brake rotor and fork lowers from mud and debris. Choose between black or white.
It seems that while packing for every adventure … we always end up with a few items that were either neglected to be packed, were last minute gear additions, or just needed to be packed in a readily accessible location…. The OBR Adv Gear Tool Pouch is the perfect solution for these miscellaneous items. Once packed the tool pouch can be slipped into any bag or attached externally using integrated webbing loops that are built into the pouch.
Features
* Tools not included
Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.
This set of high quality replacement steering stem bearings includes:
Double the size of your side stand footprint and half the chances of your XR650L tipping over when parked on soft terrain. This laser cut, TIG welded 0.190" thick slice of aluminum bolts to your machine with just the addition of a hole in the stock side stand pad. Just takes minutes to mount! All hardware provided.
2 high-quality bushings per set. They recommend changing bushings every 40 hours or at least once a year to get the best performance out of a set. If you are on an Adventure Bike and are doing a lot of road miles they recommend swapping out bushings once a year to ensure that you get the most vibration dampening of the bushings.
Every new set of pegs comes with a 90A bushing installed. This is a medium flex rating.
80A is the softest and 95A lock-out is the stiffest and has the least amount of flex.
The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference.
The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.
For use on Motion Factory Foot Pegs Only
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
Our complete foot peg assemblies. 1-3/4" lower than stock. No extra brackets that hang down below the frame. Easier on the knees. Wider platform Yamaha YZ style footpegs are stronger and give you firmer footing. Mount solid to the frame. No more 'droopy' feeling when standing on the stock pegs. Lowering your footpegs makes it easier to stand and less of a reach down to the bars when standing.
Now you can get our Low Pegs with MK4 Pivot Pegz or black Fastway ADV pegs (both Yamaha YZ pegs) installed!
An Old School design that works great on today's Dual Sport bikes.
The rubber compound is engineered for high grip and long-lasting tread wear.
DOT approved, tube type, and might be the best value in a DOT knobbie.
The Barkbuster LED Indicator Lights for Jet, Storm & VPS Plastic Handguards to increase your visibility and safety using 15 high intensity LEDs that mount directly to the plastic handguard shells. Super bright auxiliary signals will make your directional intentions clear to upcoming traffic. The LED indicators are very low draw and E marked for road use.
Features:
What's in the box:
Please Note: Not compatible with the electrical system on the Honda Africa Twin CRF1000L
The Barkbusters 10 OHM Resistor Set for LED Indicator Lights will correct the flash rate of your auxiliary signal lights. Ready to plug in connectors make installation a breeze. These resistors are intended for Barkbusters LED Indicator Lights.
Features:
This new and improved DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware. No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.
We highly recommend this kit over the non-DOT and original DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!
Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.
Low Beam: 20W, 2,800 Lumens
High Beam: 35W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Compliant
CE, RoHS, ISO9002, IP67
Please note: Fits '87-'07 (Gen 1) only
This DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.
This kit is highly recommend over the non-DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!
Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.
This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a plug and play installation however a small amount of trimming on the backside of the plastic headlight shroud is required.
This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive). The high beam is amazingly bright eliminating the need for auxiliary lighting.
The materials, construction, and aesthetics are all top notch. You won’t be disappointed.
Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive
From our friends at JNS Engineering, a very nice mount for a set of auxiliary lights on the front of your KLR650. Laser cut from 0.190" 5052 aluminum it is CNC formed and then powdercoated black. One of the best benefits is that it will not interfere with even the largest aftermarket fuel tanks. All included mounting hardware is stainless steel.
Made from heavy duty 1/8" thick stainless steel, these mounting brackets are specifically designed for mounting 2" LED auxiliary lamps to the front of your TW200. They position the lamps (not included) high & tight to the bike for optimal protection and light projection without interfering with the bike controls, body work, or fuel tank. Kit includes four longer mounting bolts for the lower triple clamp.
The image shows a GoPro camera on the TW's right side and an LED light on the left. You could certainly do something like that as well!
This guard is designed to protect your TW200 headlight from rocks, branches, and any road/trail debris kicked up by the vehicle in front of you. It’s a one piece laser cut steel component with a sleek black powder coat finish. Mounting hardware is included.
Note: installation requires drilling two 1/4” holes in your plastic headlight fairing.
A new high output stator for the XR650L. 25% more output than the stock unit. Approximately 50 additional watts. Now you can have enough power to run those driving lights and/or heated riding gear!
Installs on any bike. Key operated power & kill switch. Turns on power (Lights, etc) when key is turned to 'ON'. Disables ignition system and turns off power when key is turned to 'OFF'. Two separate pairs of wires for kill switch and bike power. Includes stainless steel mounting bracket perfect for handlebar clamp.
PSR dual sport mirrors come with a slightly convex mirror for a wider field of vision behind you. The round mirror is 4.25" in diameter while the oval is 3.75" x 3". These mirrors are easily adjustable and fold out of the way quickly with the 1" RAM mounts.
The RAM Ball Stud Base used for both mirrors will go into any standard 10x1.25 threaded mirror base.
Sold individually.
All Yamaha's will need a mirror adapter if you have the stock perch.
The Warp 9 shift lever is black anodized and the Warp 9 logo is laser etched into the finish. Comes with a black anodized knurled aluminum tip that folds and returns via a stainless-steel return spring. Includes the pinch bolt as well.
A set of replacement brake and clutch levers. Standard length.
Please be sure and order the correct levers for your model year KLR.
Note: Gen 1 levers are black
Gen 2 levers are Silver
OE style clutch lever.
This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars.
Because these are offset there may be limited clearance between the gas tank and the risers when the bars are fully turned on some models, mainly when mounted to move the bars closer.
Included with the Tank:
The simplest piece they make, in a 3, 4, 6, 9, 12 or 15 foot length. This is the runner they use on the bag snake and the side bag haulers.
This piece can be added into any luggage hauling scheme you can dream up.
SPECIFICATIONS:
Construction is a simple piece of 1" Nylon webbing with a loop sewn into one end.
They use the 4 foot length in the side bag hauler kits and the 6 foot length in the bag snake kits.
PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash.
Sold as a pair. Easy to Install
The CRF300L side racks are intended to work hand in hand with their ENDURO Series rear rack.
If you plan on installing the side racks without their rear rack, you will need the spacer kit to fill in the empty space, which we will send to you at no extra cost. Please select the option when you place this in your cart.
Please note that you will need to remove the left side rack to access your lockable factory storage hatch.
The Honda Maxi Luggage Rack and extension is made from 5mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible.
DIMENSIONS
Maxi Plate:
Will not fit adventure sports model. Please see other listing.
The Nomadic Rack for the early generation KLR650. CNC laser cut from 3/16" 5052 aluminum with a large 12" x 18" mounting surface area. Sand blasted and then powder coated black to give it a shot peened look. This rack is an easy installation with no modifications required. There are multiple strap slots for securing gear bags and cargo. Rack is compatible with RotoPax mount. All hardware and instructions included.
Packages available include Rack with the RotoPax Mount or if you really want it all, you can order the Rack, Mount and a Fuel or Water Container.
This product has been designed to fit the Yamaha T7 Ténéré
This kit will give you 80mm of adjustment over the stock screen.
In the raised position, the difference in ride comfort is remarkable. Wind noise reduction is very noticeable and airflow underneath your screen reduced the vacuum effect, creating smoother airflow and reducing turbulence.
In the lowered position, the screen sits at the same height as stock.
To adjust the screen, loosen the thumb nuts, slide into position and re-tighten the thumb nuts, no tools required.
The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.
Mounting is accomplished by drilling two holes on each side of your headlight cowl using the provided template. The shield is 14 inches tall, 11.5 inches wide at the bottom narrowing to 8.5 inches at the top. Made from military aircraft grade cast acrylic.
This unit will not fit properly on '90 to '01 DR650 headlight cowls.
The touring windshield from Parabellum has been designed, developed and tested using all the knowledge and experience of the KLR riders in their own shop. Using the stock mounting points as well as the cowling mounts increases the rigidity of the shield.
All new fasteners are included. This new design allows you to move your handlebar to different positions and will not interfere with a stand-up position for off-road use.
This shield is constructed of 3/16" military grade cast acrylic that is 17 inches wide at the bottom tapering to 16 inches at the top.
New replacement side panels specifically made for TW200.
Sold in pairs, designed to be used with Maier USA Rear Fender.
This 3rd gear set is made for us by Nova Racing Transmissions in England to replace the fragile stock third gear set. These folks build complete transmissions for World Superbike teams among others, so we believe them to be highly qualified to build this set of replacement gears.
These gears are made from a high quality special alloy steel and then heat treated and superfinished. The mainshaft drive gear and the countershaft driven gear are sold only as a set.
Includes all wheel bearings, new dust seals. The rear kit includes the bearing and seal for the cush drive hub (sprocket carrier). All bearings are sealed on both sides.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 3 |
| Seal | 2 |
High quality sprockets
Counter shaft sprocket replacement requires the removal of the left side case cover. A new gasket may be required. This is also a great time to replace that leaking oil seal!
Complete kit to rebuild OEM carburetors.
Included in this kit are the parts needed to repair a second generation TK carburetor. You get a new float bowl gasket, needle valve with O-ring, needle, mixture screw, and stock jets for the '01-'21 models kits.
FunnelWeb ProLine Filter Highlights:
Like all FunnelWeb filters, the ProLine Filter features profile cut, single layer, single density foam that doubles the external surface area of the filter without increasing the original filter size. The ProLine Filter traps dirt, dust, sand and mud over a larger area on its outer surface, ensuring optimal air flow is maintained for maximized engine performance and reliability.
The single layer, single density polyurethane foam has the added advantage of being easy to clean and the ability to maintain its original shape after numerous washes. Overall, compared with conventional foam filters, FunnelWeb offers more protection from dirt ingestion, has longer service intervals and maintains high airflow rates when dirty.
This filter replaces the stock air filter, fitting inside the air box.
This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 2008-2018 Yamaha XT250. The new design for the black headlight produces more light and has much more uniform beam pattern when compared to the previous version. New design currently only available in black, chrome may be available in the near future. No wiring, soldering, resistors, trimming, drilling, or fabrication required.
This optically clear headlight guard is CNC cut for a perfect fit. It is made of durable aircraft grade 3/16" thick cast acrylic which resists harsh rock impacts, trail scuffs, and incidental scratches. Velcro fasteners hold the guard firmly in place and allow for easy on & off should it need an occasional cleaning. Installation is a quick five minute job, positioning template included.
Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.
Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.
Planning a motorcycle trip can be hard work. Butler G1 Maps highlight the best paved motorcycle rides in the country so you don’t have to guess which roads are good. Their dedicated team rides and rates every road you see on the water-proof maps, hundreds of thousands of miles so far. Their easy to read rating system clearly indicates the most dramatic and scenic stretches and are accompanied by detailed inset boxes, written descriptions, elevation profiles and whole bunch of useful information to help you plan your journey.
Looking for motorcycle road trip ideas? How about the best dirt roads by state? Each of the Adventure Series maps highlight the best dirt roads, taking you off-road through some of the most spectacular scenery in the United States.
Each pattern is available in three advanced synthetic rubber compounds. This means you can have the optimum combination of strength, tackiness and shock absorption to suit every riding condition and individual style. Soft grip is extremely soft, giving you a very comfortable ride, great feel and reduces the chance of blisters; however, because the grip is so soft, it wears quickly. Medium is a compromise between firm and soft. Firm grip has the same feel as a stock grip, it is very strong and has very good resistance to tearing and abrasion. Half Waffle has waffle pattern in finger area for traction and diamond pattern on palm side to reduce blisters. Full Waffle: designed after the CR Honda® grip.
Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.
Thin wall bi-hex sockets designed to access narrow spark plug holes.
Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.
With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way.
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.
The Swiftkicker is 100% manufactured in the USA from the highest quality components.
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.
Measured from the center of the pivot to the bottom of the foot.
Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.
With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way.
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.
The Swiftkicker is 100% manufactured in the USA from the highest quality components.
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.
Measured from the center of the pivot to the bottom of the foot.
