Search Products

Need to remove your clutch assembly to get at that dreaded neutral safety switch? This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub. Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut easy. All of that and no worries about doing any damage to your expensive clutch hub.

Bottom line, if you have to hold your clutch hub to remove it, there is no better way to do it.

• Allows precise valve lash adjustment without disturbing the setting when the lock nut is fastened
• Knurled knob on adjuster drivers ensure a precise and secure grip
• Integrated repositionable wrench handle holds the lock nut while the drivers are used to loosen or tighten the valve adjustment screw

Set includes:

• (1) 10mm steel socket wrench
• (1) 3mm square tappet adjuster

This high quality socket from Motion Pro, is specifically designed to reach into the very small, deep space where the spark plug of the XR hides.

Normal sockets simply won't work in this case.

Replace those worn out brake pads with quality EBC replacements.

• Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability. These Aramid fibers have a high strength-to-weight, thermal stability and abrasion resistance to provide advantages over steel fiber-based products. They provide excellent stopping power without noise and rotor galling but still provide fingertip control and strong, predictable brake response.
• Double-H sintered metal brake pads feature the HH friction rating, the highest in the industry. These pads provide maximum brake effect and last twice as long as organic pads.
• Semi-sintered pads have an all new recipe containing 30% copper by weight with an organic matrix. This design combines the long life of a sintered pad with the great feel and lack of rotor damage common with full-sintered pads. These can be used to replace Kevlar or sintered metal compound pads.

High performance EBC brake pads.

• The "HH" friction rating is the highest in the industry
• Provide maximum brake effect
• Lasts twice as long as organic pads

This is a complete kit that replaces both front and rear brake pads.

Quality components at a great price.

• Standard Kit: Includes SS braided lines and EBC sintered brake pads.
• Standard Plus Kit: Includes SS braided lines, EBC sintered pads and an EBC Carbon Steel front rotor.
• Super Plus Kit: Includes SS braided lines, EBC sintered pads and EBC carbon steel front and rear rotors.
• Deluxe Kit: Includes SS braided lines, EBC sintered pads and an EBC Premium 320mm SM front rotor kit.
• Super Deluxe Kit: Includes SS braided lines, EBC sintered pads, an EBC Premium 320mm SM front rotor kit and EBC rear rotor.

SMX Carbon Look Rotor

• Rotor material has higher friction than plain stainless steel for added stopping power
• Rotors measure 320mm
• Come with caliper relocation bracket
• Designed to fit standard hubs

Warp 9 320mm Supermoto front brake rotor kit. Newly updated and stronger.

Adds serious stopping power to the DR. Included is a new rotor floating on a central mounting carrier along with a caliper relocation bracket.

Available add on options include a Galfer braided stainless steel brake line, and 12oz bottle of Bel-Ray DOT4 brake fluid.

Includes a fresh set of brake rotor bolts.

New from Warp 9, a full floating 320mm Supermoto disc with caliper relocation bracket! These rotors have an additional hole for placement of a magnet for an electronic type speedo like the Vapor.

Includes a fresh set of brake rotor bolts.

Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

These hand-crafted bash plates from B&B Eng. are constructed from 4mm 5083 aluminium plate. Strong and lightweight, this material has been selected because of its extreme suitability for welding, abrasion and impact resistance. All the necessary stainless clamps and bolts are included. Plate has a polished finish with foam or rubber where required.

Enjoy maximum protection and durability with an SW-MOTECH skid plate. Fully welded aluminum construction is engineered in Germany to provide proper protection from impacts, abrasions and projectile debris. Multiple ventilation slots on the front, sides and bottom of the skid plate permit maximum air-flow to keep your motor cool. Drilling, cutting, welding or any other permanent modifications are not required.

Features:

• Debris and collision protection for the engine 
• Fully welded 4mm thick aluminum plate / black side made of 2.5mm thick aluminum
• Efficient underbody protection of stone-chipping and collision
• Provides protection for the vulnerable oil pan & lower engine cases
• 100% bolt-on, no drilling, cutting, or any other permanent modifications needed
• Ventilated design maximizes air-flow to prevent overheating
• Silver
• Designed & engineered in Germany

What's in the box:

• SW-MOTECH skid plate engine guard
• Mounting hardware 
• Installation instructions

To fit straight 22mm (7/8″) handlebar.

• Barbusters strongest handguard EVER!
• Designed for Enduro and Trail bikes.
• Two mounting points secure the full wrap around aluminum design.
• Compact curved profile to protect hands and levers during intense trail and tight bush riding.
• Heat treated aluminum backbone for maximum strength.
• Replaceable, high impact resistant EGO plastic guards included.
• Large range of colors matched to popular motorcycle brands.
• Deflectors available for increased protection (sold separate).
• Easy installation.
• NOTE: Not ideal for bikes with long clutch and brake levers.

• Protect your investment with the Works Connection rear brake caliper guard that is simple to install and does not break the bank.
• Works Connection built the rear brake caliper guard from CNC'd aircraft grade 5052 aluminum for lightweight durability.
• No need to modify anything with this rear brake caliper guard because Works Connection includes all the hardware to easily bolt on.
• Works Connection designed and built the rear brake caliper guard in the USA.

Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty. Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever!

• Wider, lighter, stronger design
• Widest (mm) and lightest pivoting pegs on the market
• Upgraded heavy duty, long life springs
• Unique multi-directional grip pattern
• Outstanding build quality
• Lifetime Warranty*

New from Warp 9, top of the line Adventure Pegs. a full 5" long and 2.5" wide will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a single track trail.

• Ceracote coated Chromoly steel pivot for the ultimate in strength
• Replaceable 7075 T6 Aluminum Platform
• Permanent Stainless Teeth provide the ultimate in non-slip traction
• Built-in bottle opener in the bottom!

  NOTE: These pegs DO NOT fit the '18 model!

Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools. Tough black powder coated finish.

For riders who wish to run the centerstand and the lowered footpegs we recommend installing a Warp 9 brake pedal. The Warp 9 pedal is arched to give the necessary clearance under the pedal.

Did you snap a headpipe bolt on your XRL or are your headpipe bolts looking a bit dingy and rusty?

These replacement header exhaust stud bolts are made of super corrosion resistant 316 stainless steel.  They provide excellent resistance to chemicals and saltwater to give your exhaust system a hassle free service life.  

If you've got an older XR650L, you know the struggle of removing the O.E. nuts from the studs.  They either snap, remove the stud or come off as they should.  At some point you're likely to snap on or come across a seized nut to stud.  These bolts are a superior upgrade to the O.E. nut and stud.

Kit includes: 4 Stainless Steel bolts

This is a new gasket for the cylinder head - head pipe junction. Installing a new one with your new header will ensure a good seal and no exhaust leak.

The V2 Slip-On features new aluminum end caps. A USFS Spark Arrestor. DG offers 4 different Quiet Core Inserts to reduce exhaust sound. Lightweight at approximately 5.5 lb.s

A fresh set of brake rotor bolts. 

Genuine Yamaha OEM bolts work with factory and aftermarket rotors.

Comes in a pack of 6.

CycleRacks are made out of Schedule 40 11/16 black steel pipe, bent in a press, and welded together in a jig. All of their racks have the same platform, 18" wide by 12" deep. Includes lower mount hardware.

All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.

DRZ400 rack is available in both a Utility and Sport version. The Sport version is 9" x 9" and the Utility is a full 2" longer for added storage space. Both of the S/SM racks have tabs so you can bolt the stock tool bag on.

Please select the rack for your specific model as the differences are significant

• Fully welded construction from 16 gauge mild steel
• Powder-coated black textured finish
• Rigid 4 point mounting system (except off-road model rack)
• Hardware and detailed instructions included

Increase your fuel and/or water carrying capacity. This mounting plate attaches to the OEM Suzuki rear rack and accepts the standard RotoPax mounting pedestal. The use of pressed-in threaded mounting hardware allows for quick and easy installation of the plate and pedestal. When not needed the RotoPax pedestal can be quickly removed and the tidy JNS mounting plate left in place.

• 0.125" 5052 Aluminum, Laser cut / CNC formed
• Powder coated black
• Includes stainless mounting hardware

Order alone or with RotoPax Mount and Water or Fuel container. Get everything you need at one time.

• Made with Industry leading UltraMax® fabric
• Maximum UV protection against fading
• Heavy duty webbing and buckles for easy and secure mounting
• Fully expandable (Dual Sport/Enduro & Adventure only) with reflective piping
• Rigid construction allows the bag to hold its shape when empty
• Water resistant lockable zippers help keep out dust and dirt
• Inner self-fastening straps to better secure contents
• MOLLE panel on lid allows other items to be strapped down
• Rubberized carry handle for easy transport

Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 3 strong powder coated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approximately 13" long.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

Does not fit if your bike is equipped with the new emissions system. The charcoal canister prevents the tool tube from being mounted properly.

The universal E-series adapter plate is designed to add a Givi Monokey topcase to most existing flat rear luggage racks. All necessary mounting hardware and installation diagram for attachment to generic tubular-steel flat rear luggage racks is included. This is a universal plate so making it work on your tail rack might need a little self engineering.

Typically installs quickly using simple hand tools. Mounts standard Givi Monokey topcases (ie E45 Elegant, E460 Delux, E52 Maxia), or the flat, stable surface can be used as a solid toprack when the topcase is not needed. Not for use with GIVI Monolock topcases. Made of durable molded nylon with a rugged black finish.

What's in the Box:

• GIVI E251 Adapter Plate
• (4) W-style Adapter Hooks
• Mounting hardware
• Installation instructions

Fly Racing small tank bag has a 7.5 liter capacity, with touch screen compatible top map/device pocket that holds most GPS and cell phones.

Combined strap and magnet mounting system, reflective piping and logos, and convenient carry handle.

Micro fleece lined exterior pocket, and includes rain cover. Measures: 13"L x 10"W x 5"H

This is the ultimate headlight upgrade for your XT250! It’s a plug & play kit which includes the newly released Morimoto round headlight with preassembled aim adjustable mounting bracket set. Installation takes five minutes and the light output is phenomenal.

Low Beam: 2,400 Lumens, 20 Watts
High Beam: 4,300 Lumens, 35 Watts
Color Temperature: 5,000K
Warranty: 5 Years

This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 1996-2020 DR650SE. No wiring, soldering, resistors, drilling, or fabrication required however due to the size of the headlight minor trimming on the backside of factory plastic headlight fairing is needed in non-visible areas.

• Low Beam: 25W, 3,600 Lumens
• High Beam: 40W, 4,500 Lumens
• Color Temperature: 6,500k
• CREE LED Chips
• DOT & SAE Approved
• CE, RoHS, ISO9002, IP67

This kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.

The headlight features two primary sets of LED projectors, a wide low-beam pattern with distinct upper cutoff and a center spotlight high-beam for long range visibility.

The low-beam consumes 20W and remains powered when the 15W high-beam is fired. There is also a daytime running light feature which can be powered for additional glow. The LEDs are rated for 50,000 hours and operate at a 6000K color temperature.

No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.

Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.

Non-DOT

This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a one beer, plug & play installation.

This is the best performing and highest quality headlight they currently offer.

The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive, ie USA).

The high beam is amazingly bright eliminating the need for auxiliary lighting.

The materials, construction, and aesthetics are all top notch. You won’t be disappointed!

Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive. (USA)

This kit includes the all new Morimoto 4×6 LED headlight and a pre-assembled JNS Engineering adjustable mounting bracket set. Like the rest of the JNS headlight kits, installation is a simple 5 minute plug-and-play procedure.

This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform/controlled, and features a proper upper cut-off. The high beam is amazingly bright, eliminating the need for auxiliary lighting (money saved!). Plus the 5,000K color temperature is extremely easy on the eyes. The materials, construction, and aesthetics are all top notch.

It’s a next level headlight, you won’t be disappointed.

Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive

Does not fit '87 TW200 because that year has a unique AC powered headlight circuit.

Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.

White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.

Dazzling bright Amber blinker functions. 

Everything comes in a spring-loaded stock designed to keep it safe from those unexpected tip-overs, crashes, or encounters with brush and trees. They’re flexible enough to bend 360 degrees, yet tough, durable, and almost impossible to break!

If you have a single indicator light for the blinkers that is not built into the display and is not LED you will need the diode kit (AKA DR650) If it is built into the speedo display it should not require the diode kit.

Available in a generic kit with Bullet connectors supplied. Great for your DR or almost any other bike with a single post blinker setup. These will work well on bikes that use a flasher, but you might have to add the female side of the connectors that are included in the kit.

Not for Yamaha T7, see model specific listing

Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.

White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.

Dazzling bright Amber blinker functions. 

All in a spring-loaded stock to prevent damage from a tip over, crash or impact with brush, trees etc. They will bend 360 degrees, but are stiff, durable and nearly unbreakable.

Kawasaki KLR650 Gen 3 / KLX300 Specific plug and play kit using factory connectors, flasher and block off plates.

Reproductions of the original DR650 factory turn signals. Save a bundle compared to the $70+ each cost of the OEM signals. The wire pigtails plug directly into the factory harness. No cutting or splicing necessary. Choose original style amber lens or clear lens with amber bulb.

• Keep your EFI tuner secure with the Power Vision handlebar mount kit
• Vital ECU information can be within view, or use the imbedded datalog feature of the PV3 to log data and review later in Power Core software
• This universal kit will fit multiple handlebar sizes by using reducer bushings
• Works on handlebars up to 1-1/4”
• Made in the U.S.A. 

Please note that the Power Vision 3 Handlebar Mount is used in conjunction with POD-300 Digital Display

The perfect complement to our Power Commander V or AutoTune modules, the POD-300 gives you an accurate real-time reading of your vehicle’s vital fuel, engine and air information. 

Featuring a robust array of options, you can toggle the display, so the data most important to you is front-and-center. The POD-300 can log channels to internal memory, then access them when you’re done riding through our Power Core software (only available for Windows computers). This display module connects to your Power Commander V/6 or Wideband 2 device network through a CAN cable (included). 

The POD-300 is weather-resistant, so it can be used in any environment. The high-contrast display is easily viewable in direct sunlight. It includes a velcro backing for easy installation and removal, or you can purchase a handlebar mount separately. 

Please note that the POD-300 is a display module only, which is used in conjunction with Power Commander V, Power Commander 6, AutoTune or Wideband 2.

• Clear, high-visibility display module
• Allows for real-time fuel adjustments
• Weather-resistant
• Connects to Power Commander V/6 or AutoTune via CAN cable (included)
• Log channels to internal memory, analyze with Power Core Software

The EJK evolved out of the need to address the ever-increasing complexity of factory fuel injection. For the newcomer to the market or professionals wanting an easier method for tuning fuel injection, the EJK is a customizable solution for the rider that wants to take control of their tuning needs.

This unit is a piggy-back EFI controller because it does not replace the stock ECU, but rather monitors the signals to the injectors and makes fuel adjustments based on the mode settings. The GEN 3 has a push button interface allowing access up to 6 different modes to allow for quick fine tuning by the end user without needing a computer.

Key Features:

• No computer or dyno needed!
• Plug and play, simple to install, base settings preset
• Unique load based technology
• Full range tunability available
• Does NOT interfere with stock ECU operation
• Simple push button adjustment interface
• Water-resistant 
• 2-Year warranty
• Compact size - 2.2" H x 3.4" W x 0.5" D

• Dual-bonded foam design filters out even the smallest dirt particles, while allowing more airflow than two separate layer filters (flow bench proven)
• Twin Air filters are slightly smaller than stock to make them easier to change and to increase dead air space around the filter for better performance
• Flat foam sealing ring securely seats against the airbox, even in the worst riding conditions

• Increased air flow over the stock air filter
• Designed to increase horsepower and throttle response
• Designed to fit inside the factory air box
• Larger surface area over foam filters which offers longer service intervals in dusty conditions
• Four layers of premium cotton gauze provides outstanding filtration
• Washable & re-usable, never wears out
• One filter will last the lifetime of your bike

If you are converting a Keihin FCR-MX 39 to fit on your DR, you need to start here. This 6061 T6 aluminum adapter bonds to the airbox side of the carb so it will easily fit the DR.

  Not for the stock carburetor Fits FCR-MX conversions only.

Designed for use with stock engines using either stock or aftermarket exhaust and air filters.

• Provides a simple and affordable solution to carburetor tuning problems
• Allows you to tune your bike for increased power and smoothness while retaining fuel economy
• Includes a guide booklet on how to install and use your jet kit to it's full potential

Kit includes:

• 155 Main Jet
• 40 pilot jet
• #35 leak jet
• EMP needle

Not for the stock carburetor Fits FCR-MX conversions Only.

Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes Fork Seals and dust wipers.

Save time and money with this complete OEM quality fork bushing kit.

• Kits include fork leg and slider bushings along with any needed snap rings, o-rings and copper washers

Lowers the rear suspension. Precision machined from billet aluminum and anodized.

Reinforced for added strength/durability when adding weight.

*Important when lowering the rear suspension you want to raise the fork tubes in the clamps an equal amount of inches that the rear is being lowered. That way your bike will sit level when done.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

Kouba lowering link will lower the rear suspension 1.75". Comes with bearings and seals installed for a quick and easy installation.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

Billet aluminum lowering links. Lowers the rear suspension approximately 1 to 2 inches depending on application.

*Important when lowering the rear suspension you want to raise the fork tubes in the clamps an equal amount of inches that the rear is being lowered. That way your bike will sit level when done.

Note: We only recommend the 2" lowering links for lighter non-aggressive riders as they allow the tire to rub when near bottoming.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.

Stiffer fork springs are recommended to get the full potential of the DDCs.

Fork brace precision machined from aluminum barstock. Drilled and tapped for optional lower fender attachment.

Hard anodized black for corrosion protection. Fits OEM forks. Split design allows for installing in minutes without having to remove the forks.

Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.

• Increased tank 14L / 3.6 Gallons.
• Impact and abrasion-resistant.
• Ideal for both competition and long and short-distance tourism.
• Designed to maintain a narrow profile to ensure excellent driveability.
• Possibility of fitting cap with Acerbis key.

Included with the Tank:

• Acerbis cap
• Assembly kit

Acerbis fuel tanks were designed to provide additional fuel capacity without sacrificing ergonomics, and are the perfect choice for the rider trying to increase the range of their machine. Constructed of impact and abrasion resistant Polyurethane, Acerbis fuel tanks are durable, stylish, and will provide years of service.

• Complete set of friction plates, steel plates, and springs
• Heavy-duty springs help prevent clutch slip
• Restores proper stack height, fixes clutch slip caused by wear and tear

Replace your worn clutch plates and springs to reduce fade and slip.

• Complete set of friction plates, steel plates, and springs
• Heavy-duty springs help prevent clutch slip
• Restores proper stack height, fixes clutch slip caused by wear and tear

GoldPlug is the gold standard in engine protection.

Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.

10MM Thread

Complete Gasket Set includes all the gaskets necessary to rebuild the entire engine and transmission, including valve seals.

The idler gear is one of the few plastic components in the DR650 that can significantly impact engine performance if it fails or breaks.

This gear is crucial for driving the oil pump, which ensures proper oil circulation throughout the engine. In the absence of this component, complete engine failure may occur. While the idler gear is not frequently cited as a common failure point in the DR650 engine, failures have been reported, typically manifesting as either a fractured gear or stripped teeth.

During inspection, it is essential to check for any cracks, chipped areas, or missing teeth on the idler gear. Replacing the gear is a straightforward procedure, and it is advisable to do so while the clutch side case cover is already removed for other maintenance tasks, such as NSU screw replacements or clutch hub bushing replacements.

This component is a Genuine Suzuki part.

The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.

This windscreen mounts securely to the three stock windshield holes as well as the two side cowling mounts. The shield is 14 inches tall, 13 inches wide at the bottom narrowing to 11 inches at the top. Made from 3/16" military aircraft grade cast acrylic.

The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.

Mounting is accomplished by drilling two holes on each side of your headlight cowl using the provided template. 13.5 inches tall, 11.5 inches wide at the bottom, and 8.5 inches wide at the top. Made from military aircraft grade cast acrylic.

The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.

This shield mounts simply to the stock headlight shroud using minimal hardware to keep weight down. The Rally Windshield measures 12.5 inches tall, 11.5 inches wide at the bottom, and 8.5 inches wide at the top. Made from 1/8 inch acrylic and offered in clear or tint.

Finally! Quality replacement body parts at a fraction (35%!) of the OEM parts. Polisport's parts have been developed with their exclusive technologies - IPD (In-mold Plastic Decals) and DGP (Durable Gloss Propylene). These processes make these parts even more resistant and durable than the stock units with a perfect fit and glossy finish. The Side Panels include heat protection film, washers and rubber grommets, just like the OEM parts.

You can purchase individual parts, or a discounted complete kit. If your taillight unit was damaged with your rear fender, we offer a brand new OEM unit as an optional add on.

• The distinctive look of Acerbis is everywhere
• OEM color-matched for direct replacement or works look
• Pre-drilled pieces mount easily to stock locations
• Radiator covers and side panels sold in pairs

ProTaper's ADV handlebars give you a bar taller than most with extra space on the control portion of the bar. These bars provide an additional 20mm of space next to where your levers and throttle are located for your GPS, phone cradle, auxiliary switches, etc . They come in Adventure (which is taller than stock) and Adventure High (which is even taller).

These are oversize bars, which means they are are 1 1/8", not the smaller 7/8" diameter. Therefore some bikes will require a adapter and there are several available to select from.

Using the same manufacturing techniques and materials as ProTaper’s industry-changing 1⅛" motocross handlebar, the EVO Adventure is specifically designed to provide adventure/touring riders with the increased comfort and control they need. With over 8" of straight section in the control areas, mounting vital components is made easier than ever. With its premium 7000 series aluminum alloy construction and computer-profiled four millimeter-thick wall design, the EVO Adventure Handlebar is up to 25% lighter and 45% stronger than competing handlebars.

• 1⅛" tubing at the clamping area
• Exclusive 4 mm-thick 7000 series aluminum alloy for superior tensile and yield strengths
• Optimum balance between fatigue life, impact strength, and impact-absorbing flex
• High-tech shot peened, stress-relieved, and anodized finish for unmatched durability
• Independent lab tests show that the EVO Handlebar leads the market in fatigue life
• Epoxy inner coating resists corrosion
• Chemically applied cut lines and alignment grid are scratch- and peel-resistant
• Plastic bar end plugs keep the elements out and provide a stronger base for grip ends
• Weighs only 1.55-1.7 lbs. (720-780 grams), depending on bend

Say goodbye to the frustration of fidgety handguard expansion plugs with Warp 9's innovative Tapped Handlebars. 

These handlebars feature ends that are plugged and tapped with an M8x1.25 threaded insert, providing a secure and reliable mounting point for all aftermarket wrap-around handguards. 

No more worrying about plugs pulling out or spinning during crashes; their robust design ensures you're good to go, even when you encounter obstacles. 

Not using handguards? No problem they've got you covered!Each set of handlebars comes with aluminum grip guards and stainless bolts, offering protection for your grips and delicate throttle tube in case of a get-off. 

Designed with an oversized 1-1/8 inch (28.6mm) clamping diameter that tapers down to 7/8 inch (22.2mm) to accommodate standard controls. Crafted from 7010 T6 aluminum tubing and featuring computer-extruded variable wall thickness, they effectively reduce vibration while enhancing overall performance and comfort. 

Note: Does not include pictured bar mounts.

Aero Tapered Aluminum (ATA) Oversize (or Fat Bar) Handlebar.

• GP High Bend
• Black in Color
• Aerospace grade, heat treated 7075 T6 aluminum construction
• Shot-peened and anodized finish for maximum strength and durability
• Calibration marks for precise mounting
• Clutch-side knurling for maximum grip adhesion
• Stronger and lighter than conventional aluminum handlebars
• Controls the flex to dissipate shock and impact which reduces rider fatigue
• The molded bar pad provides superior impact protection and features and innovative mounting solution for easy installment and positioning
• 1 1/8" clamping diameter tapers to 7/8"at bar ends
• Handlebar is lighter than the competition; it weighs only 1.4lb
• Durable, laser engraved graphics
• 80mm bore depth to accommodate most handguards

For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8  adapter (sold separate).

Genuine Suzuki replacement brake and clutch levers. Standard length. 

Available as a set or individual.

Please notice that this set is for '10-current DR650.

• Manufactured to exact measurements to meet or exceed oem specification
• Tempered steel wire housing with an inner nylon sleeve for long life & smooth operation

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!

The Complete Seats come assembled with an aftermarket pan and ready to ride.

These wider seat kits from Seat Concepts keep you comfortable on those long commutes or dual sport rides. The added width and improved foam density will help keep your seat from being the item to stop you from going on those big rides or enjoying the bike. 

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.

Thread Chasers are designed to clean and re-cut damaged aluminum threads.

This kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.

Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.

Uses 8mm or 10mm hex sockets, a Must for all tool kits.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

This optically clear headlight guard is CNC cut for a perfect fit on your XT250. It is made of durable aircraft grade 3/16" thick cast acrylic which resists harsh rock impacts, trail scuffs, and incidental scratches. Velcro fasteners hold the guard firmly in place and allow for easy on & off should it need an occasional cleaning. Installation is a quick five minute job, positioning template included.

The 12oclock Labs EXUP Emulator is used in place of the stock exhaust servo motor when you replace the stock exhaust with an aftermarket exhaust system. The microprocessor controlled EXUP, emulates the exact characteristics of the stock exhaust servo motor and its motor delay sweeps, keeping the ECU from displaying the dreaded check engine light. Weight is less than 1/2 an ounce and it is a direct plug and play replacement.

A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.

Fits 520, 525, and 530 pitch chain.

The chain slider protects the swingarm from contact with the chain. Replace yours before it wears through to the swingarm.

A real Heavy-Duty Chain Guide manufactured from 5mm (3/16") thick 5052 Aluminum. This guide will take a pounding and continue to put that chain right on the sprocket. The rub block is machined from UHMW plastic and can be positioned to fit just about any sprocket available for the DR. These are powder coated black for a great look and additional protection.

A CNC machined chain guide for the DR. Stronger than the wimpy stock unit and can easily accommodate the stock 525 chain as well as a 46 tooth rear sprocket (by moving the lower rub block to the forward position). The rub blocks are also a higher grade, longer lasting material.

• Constructed of the highest quality 1045 high-carbon steel
• Exclusive heat treatment and quenching process for strength and durability
• Nearly all machines come equipped from the factory with this sprocket
• The strongest, longest lasting steel replacement sprocket available

• Long mileage, serious traction and smooth transition from pavement to gravel to dirt, the GPS does it all.
• Reversible rear to suit the rider’s needs – either 50/50 or Mostly Off-Road.
• In 50/50 direction the GPS is a well behaved street-able tire with smooth cornering transition from center to cranked all the way over.
• In Mostly Off-Road direction the aggressive straight line hook-up and cornering drive is engaged for better off-road traction.
• Stronger carcass construction than other 50/50 adventure tires provides world class performance with a high resistance to punctures
• Deeper tread than most adventure tires.
• Unique Hybrid compound with Silica for long mileage and optimum grip in mud and snow.

NOTE: Tubes can be run in Tubeless (TL) tires.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

• Stop your expensive helmet from falling and hitting the ground while you’re out riding
• The perfect solution to easily store your helmet with your bike.
• 7075 T6 machined aluminum
• Fits all 7/8 handle bars
• Includes 2 stainless screws
• Fits virtually all bikes and makes ( except Harley )

Ready to go tool kits. Just toss it in your bag and hit the road... or the trail.

The Phillips type screws used in Japanese motorcycles are actually Japanese Industrial Standard (JIS) screws and are easy to strip if you are using a regular Phillips screwdriver.

Here is a little kit that will make removing and replacing JIS screws much easier. Includes 2 each of JIS No. 1, No. 2 and No. 3 bits.

These will work in other bit holders and have a mild magnetic tip.

Features:

• 2-ended design combines brush and pick with a curved spade to help vehicle clean off mud and debris
• Curved spade for the big stuff
• Brush head to clean controls and radiator
• Pointed tip for foot pegs and hard to reach places
• Includes a hanging hole for easy storage in the garage
• Ergonomic handle is made from durable ABS plastic
• Patented design

Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers

• Knurled anodized aluminum locking ring
• Perfectly weighted to drive seals
• Carbon steel body halves

Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers

• Knurled anodized aluminum locking ring
• Perfectly weighted to drive seals
• Carbon steel body halves

Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers

• Knurled anodized aluminum locking ring
• Perfectly weighted to drive seals
• Carbon steel body halves

Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers

• Knurled anodized aluminum locking ring
• Perfectly weighted to drive seals
• Carbon steel body halves

• This high quality SAE to USB-C and USB port adapter features a switched on/off digital voltage display, allowing you to power your devices with either USB or USB-C charger cables
• It comes with a cover for the USB and USB-C ports when not in use, and 2 zip tie slots (zip ties not included) on the back for securely attaching the adapter to your vehicle
• Its size of 3" x 1-1/4" x 3/4" and protective outdoor rating makes it the ideal solution for your vehicle to charge phones or devices producing 5V at 3.1a power
• Easy install to your SAE battery connector cable
• Crafted from durable ABS plastic
• Standard USB port
• Cables and adapters sold separately 

• Designed to quickly and precisely remove outer bearing race from the steering head without the use of a hammer and punch
• Puller design ensures bearing is pulled perfectly straight to eliminate possible damage to frame
• Works on all tapered bearing races from 47 mm to 55 mm OD
• Precision machined anodized aluminum cup will not damage seal surface
• Brass bearing washers for easy use and long life
• Hardened steel jaws engage securely on inner bearing lip
• Lifetime limited warranty

• Durable 6061 aluminum with blue anodized finish and laser engraved logo
• Used to push the tire bead down into the drop center of the rim on off-road wheels while using tire tools to change tires
• Hooks over spoke and pushes bead down on opposite side of tire from tire irons
• No more fighting to keep bead down while installing off-road tires

No more fighting to keep the bead down while installing or repairing your off-road tires. The Bead Buddy holds the tire bead down in the drop center of the rim during tire changes making changes as easy as possible. Machined from tough 6000 series aluminum the Bead Buddy is light weight and compact enough for any tool pack. The Delrin securing thumb screw insures no scratches to your rims.

The Bead Buddy is NOT recommended for use with Bib Mousse tubes.

Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides it's extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position. There is no hazardous acid or heavy metals and it is non-explosive and non-combustible.

The Firepower features Increased cranking amps over lead acid batteries and has a very fast recharge cycle and can be brought up to a 90% charge within 6 minutes and also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.

145 CCA 12V/28.8WH
Package Dimensions: 4.75" x 3.00" x 4.50

Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position. There is no hazardous acid or heavy metals, it is non-explosive and non-combustible.

The Firepower features Increased cranking amps over lead acid batteries and has a very fast recharge cycle and can be brought up to a 90% charge within 6 minutes and also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.

Rated at 250 CCA (Cold Cranking Amps)
Package Dimensions: 6.20 x 3.70 x 4.80

Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position.

The Firepower features increased cranking amps over lead acid batteries and has a very fast recharge cycle, and can be brought up to a 90% charge within 6 minutes. It also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.

220 CCA 12V/48WH
Package Dimensions: 6.20 x 3.70 x 5.25