Set your bike apart with a custom exhaust look. Withstands direct heat up to 2000°F.
The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.
This gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers do not require a joint gasket but the all other aftermarket mufflers as well as the stock muffler require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.
Bradley performance bomb header for TW200.
By positioning this “Bomb” at a key point in the system, increased performance and flow is achieved through the expansion and contraction of exhaust sonics through the system. The result is a flow increase of nearly 10%.
The outer chamber in the Powerbomb allows the air to expand, cool and ramp back up at a higher velocity.
Fits all years of TW200 and works with all other brands of mufflers. Stainless steel and nickel plated. A clamp-on shield can be added, sold separately.
A quality replacement speedometer cable from Motion Pro.
A quality set of replacement throttle cables from Motion Pro
The Trail Mirror is a simple solution for any dirtbike or mountain bike. Gives you hindsight when you need it, but you forget it's there otherwise.
Zip ties directly to the bar- no hardware required.
Sold individually
A stock replacement brake pedal for the DR650. Nothing fancy but sure gets the job done. Just order it up and get back on the trail. See our Brake Pedal Adjuster Bracket that allows you to adjust the position of your brake pedal to perfection.
Sold Individually
A set of polished aluminum replacement brake and clutch levers.
For the frame drain on your XR650L ,extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!
Has your TM40 carburetor been sitting for too long and now needs to be rebuilt? Then what you need is this TM40 Rebuild Kit that contains Genuine Mikuni replacement parts.
This kit includes:
Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air- the number 1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow
Unsurpassed in airflow, dirt stopping and overall performance. Adding a pre-filter to your intake system gives you extra protection from damaging contaminants.
Is the cylinder head intake boot on your DR650 cracked or weathered, is it missing parts of the lip to seal around the carburetor, have you recently pulled the intake boot off only to realize the O-ring behind it is hard & brittle? This kit is your solution to solving some of those mystery problems and make your bike like new again. There can be a great deal of heat that can radiate behind the cylinder head on a DR650 as it is an air cooled engine. With that comes long term maintenance items that will need to be replaced due to them being made of materials that cannot withstand those constant heat cycles indefinitely.
Our kit includes O.E. parts from Suzuki to include:
Kit includes:
Everything you need to dial in your FCR/DR650 conversion. Enough jetting to cover most modifications or altitudes.
Not for the stock carburetor Fits FCR-MX conversions Only
The Chilly Exhaust Heat Shield is the most effective heat shield on the market. The innovative three piece design consists of a top shield attached to 2 rails with rivets and spacers. This reduces the contact area and slows down heat transfer. They have incorporated a patented, insulated reflective blanket on the underside of the shield to reduce radiant heat transfer. The included stainless steel clamp makes it simple to install.
We highly recommend a heat shield if you run soft luggage without hard racks.
FEATURES:
DIMENSIONS:
If you already have a Quad Lock Case, you can Twist Lock and Go with any of these secure mounts.
Or Choose the Universal Adaptor to use your current phone case.
The Quad Lock® Handlebar Mount is the ultimate smartphone mount for motorcycles, compatible with all Quad Lock® Cases including the Quad Lock® Universal Adaptor for other Android phone devices.
The Quad Lock® Handlebar Mount gives you the flexibility to mount your phone in a convenient and visible location using a rotating head and includes an extension arm if extra clearance is required. With your phone securely mounted to your motorcycle, you can use navigation apps to guide you to your location with ease and always stay connected.
Standard:
NOTE: Case not included
Motorcycle Vibration Dampener is recommended for use with this product.
If you already have a Quad Lock Case, or Universal Adapter and Mount you can add these accessories to Twist Lock and Go on another level.
The level of vibration from some motorcycles can affect the image stabilisation on new smartphones. The Quad Lock Vibration Dampener ensures you can confidently mount your smartphone to any motorcycle.
FURTHER PROTECT YOUR SMARTPHONE
Compatible with all Quad Lock Motorcycle Mounts and Quad Lock Motorcycle Accessories, the Quad Lock Vibration Dampener reduces over 90% of high frequency vibrations produced by motorcycles.
PRECISION ENGINEERED
Featuring a dual chassis suspension system with precision engineered silicone grommets, the Vibration Dampener absorbs vibrations to protect your smartphone’s camera.
EASY TO INSTALL
The Quad Lock Vibration Dampener comes with everything you need to integrate with your existing Quad Lock Motorcycle Mount and can be installed in minutes.
Includes new Suzuki side panels, heat shield, headlight cover, rear fender and your choice of aftermarket off-road or supermoto front fender.
Choice of off-road or supermoto (SM) front fender.
Blue kits come with white side panels.
Quality windscreen made from Lucite aircraft acrylic making it more rigid and optically clearer than OEM windscreens
These models are 2"-4" shorter or 2"-4" taller than stock to meet your particular riding preference.
Rear Fender comes with built in tabs designed to be used with Maier USA Side Panels.
Quality replacement rear fender from Maier.
Quality MX style rear fender from Maier.
Quality replacement headlight fairing for Gen 1 KLR650.
Available in 4 colors.
Front fender from ProCycle Plastics (formerly DSA) is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does. Vacuum molded, these are a design improvement over stock. These are fully compatible in any combination with the original factory plastic.
This is an extended version of the stock DR650 clutch release arm that is manufactured by Suzuki.
Upgrading to a longer clutch release arm will lighten the pull of the clutch lever through means of increased leverage. This means less fatigue, quicker clutch engagement, easier clutch modulation and longer rides.
The extended clutch arm will not offer a drastic change in clutch pull. If you're looking for a major change in clutch pull at the lever, we recommend getting a Magura hydraulic clutch kit.
Stock and typical after market drain plugs can protrude past some skid plates. This steel low profile drain plug stays inside the skid plate so it can't be snagged by passing objects.
Comes with 4 crush washers.
Providing unbeatable performance and exceptional value, Hi-Flo Filter is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
Grab our 5-pack and save both time and money!
The PSR Oil Filler Caps are CNC machined from high quality aluminum and come with an E-clip that is already safety wired to a mounting tab. The wire is covered with silicone tubing that will not melt or discolor. Available in silver, black and gun metal.
PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash.
Sold as a pair. Easy to Install
Precision Motorcycle Racks strongly recommends these side racks be used with their Top Rack because the racks use each other to mount properly. They were never intended to be used by themselves without the rear rack.
If you are going to mount these side racks without the use of their top rack please select the extra hardware kit option that includes 2 brackets, 2 steel spacers, and an extra hardware kit that is required for proper installation.
These side racks will not play nice with any other brand rear rack, and installation without their top rack will prove to be quite difficult.
The B&B Off Road Engineering rear carry rack is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible. Our carry racks are Tig welded with a polished finish and are sturdy enough to use as a grab handle.
DIMENSIONS
Width Flat Surface Approx 18cm
Length Approx 33cm – Total Length Approx 45cm
Please Note- To fit rack, two holes need to be drilled into the rear guard. The position of holes are already marked on genuine Yamaha guard so no template is required.
These are high-quality straps made by Givi. They have a nylon belt with an anti-slip metal safety buckle. The long strap is 67" long by 1" wide with a 100 kg maximum traction load. The short straps are 39" long by 3/4" wide with a 75 kg maximum traction load.
Size: 25mm-1700mm
You can add the double D ring loop to any 1" flat webbing system. This simple piece adds a lot of flexibility to any luggage system you are using. Instantly and easily create a mount point or adjustment point on almost anything. Double D Rings can be used as a secondary buckle and works the same way as a helmet strap. However, the double D rings should NOT be used as a primary means of securing luggage.
Available in 6 colors.
CONSTRUCTION FEATURES
2 high-quality bushings per set. They recommend changing bushings every 40 hours or at least once a year to get the best performance out of a set. If you are on an Adventure Bike and are doing a lot of road miles they recommend swapping out bushings once a year to ensure that you get the most vibration dampening of the bushings.
Every new set of pegs comes with a 90A bushing installed. This is a medium flex rating.
80A is the softest and 95A lock-out is the stiffest and has the least amount of flex.
The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference.
The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.
For use on Motion Factory Foot Pegs Only
50mm step width provides better grip and control
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm.
Our complete foot peg assemblies. 1-3/4" lower than stock. No extra brackets that hang down below the frame. Easier on the knees. Wider platform Yamaha YZ style footpegs are stronger and give you firmer footing. Mount solid to the frame. No more 'droopy' feeling when standing on the stock pegs. Lowering your footpegs makes it easier to stand and less of a reach down to the bars when standing.
Now you can get our Low Pegs with MK4 Pivot Pegz or black Fastway ADV pegs (both Yamaha YZ pegs) installed!
The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option.
Wider foot pegs for sure-footed comfort.
17-4 cast stainless steel.
| Width | 1.97" |
| Length | 3.18" |
Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.
Thin wall bi-hex sockets designed to access narrow spark plug holes.
The genuine factory shop service and repair manual. This is the reference manual Yamaha dealers use in their service departments. It has all the necessary info to do any maintenance or repairs to your WR250R or X.
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of the big Acerbis or Clarke tank? The 4.0 gallon tank from IMS might be just right. Includes cap, uses stock petcock.
You’d be amazed at the dirt and debris that can work its way into your gas can – and from there, your fuel tank. Twin Air’s monofilament screen pocket inserts in your tank to catch particles as small as 40 microns (.00165”) while allowing the gas to flow freely.
The flange is custom-sized for each modern 4-stroke model to ensure a leak-proof seal. Just remove the filter periodically, turn it inside-out, and clean out the debris that could have been in your engine.
Will not work with factory locking gas caps.
Inside tank inlet diameter must be approximately 43.5mm (1.71") to fit.
Includes all necessary o-rings and diaphragms
For reference, the stock gearing for the WR250R is 13/43 while the X model runs with a 13/42 stock configuration because of the SM wheels/tires. Both use a 108 link chain with the stock gearing.
The JT rear sprockets listed are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Limited availability on Aluminum from PBI. Manufactured from aircraft 7075 T651 Plate Aluminum.
If you want the additional low-end grunt that the 46, 48 or 50 tooth rear sprocket will give you, you will need longer chain as well.
New Rear Sprockets require new Sprocket Bolts because of a difference in the holes vs. the stock bolts.
There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.
You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.
We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.
This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.
There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.
You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.
We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.
This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.
This kit includes a DOT LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
How does this headlight compare to our original TW200 kit? First and foremost, this kit has SAE/DOT markings and a much wider/brighter high beam pattern. The low beam is very similar to our original kit: wide, flat, and bright but with more punch. The DOT headlight assembly has also proven to be more durable than the original headlight.
Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Approved
CE, RoHS, ISO9002, IP67
No cutting, drilling, or wiring modifications! Installation takes 5 minutes.
Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.
Please note that this product is not compatible with the 1987 TW200.
This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.
Not compatible with any DRZ400
The Barkbusters 10 OHM Resistor Set for LED Indicator Lights will correct the flash rate of your auxiliary signal lights. Ready to plug in connectors make installation a breeze. These resistors are intended for Barkbusters LED Indicator Lights.
Features:
The Mojave Series LED Racing Lights have been designed to survive and operate in extreme conditions. Lights feature a heavy duty housing that can withstand hard impacts and a lens that is twice as thick as traditional lights. The light includes three different replaceable lens (Flood, Spot, and Combo).
Features:
This kit will work with the 6.6 Gallon Acerbis fuel tank for the DR650. You must run the light brackets inwards in order for there to be proper clearance with the 6.6. Gallon tank.
Kit includes:
Use this tool to check for air leaks in two-stroke engines. It includes air pressure gauge, pump-up bulb and most fittings and adapters for single and twin-cylinder two-stroke motorcycle engines. Packed in a convenient carrying case with instructions.
Made from precision-drawn, chrome-vanadium tool steel, the BikeMaster® 9-Piece Ball End Hex Wrench Set and Holder features a bead-blasted surface for a better grip and a corrosion-resistant coating. They have a ball end, allowing an angled reach and access to obscured bolts. It comes with a durable holder and manufacturer's lifetime warranty.
Comes with sizes 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm and 10mm
Closed handguard with aluminum bar and bracelets.
Ultra-durable closed handguard designed for those seeking greater protection while competing or riding in enduro, hard-enduro and cross-country racing.
Equipped with a 35 mm "C" section anticorodal bar. Provides 5 times more resistance than the classic handguard with an aluminum bar.
The cuffs, oversized with a thickness of 19 mm, guarantee greater strength and increased torsional capacity.
Expanders made entirely of steel.
Cover is impact resistant; wide area protects the pilot's hands more, while flexible lower area absorbs any accidental contact with the knee.
Mounting kit included. Mounts to all off-road competition bikes (motocross and enduro) with inner size from 13.5-16 mm and outer size from 22-28 mm. Works with 7/8" or 1-1/8" bars.
Co-molded logo.
For straight 7/8" handlebar
Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.
Features:
What's in the box:
Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.
Maximize your wind protection with Barkbusters' largest handguard plastic! For use with single sided Storm mount and all Barkbusters backbone handguards
For Tapered 1 1/8" Handlebar
Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.
Features:
What's in the box:
Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.
NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar
High quality aluminum caliper guards from Works Connection protects your brake caliper and looks great too.
Protect that vulnerable rear master cylinder with this thick aluminum guard from JNS Engineering. CNC laser cut then formed and given a clean black powder coat finish. Includes new button head screws and aluminum spacers.
This is the ultimate radiator guard for the CRF250L. Protects your radiator from both front and side impacts.
A rear mounting bracket provides that extra support. Constructed from 1/8" aluminum, the kit includes all necessary mounting hardware for a very simple installation.
Givi makes a great set of Crash Bars available for the Africa Twin. If your intentions include off-road riding of any kind, you really should not go without protection. Not only for you, but for your bike too. Even a slow-speed tip-over can cause damage that would make riding away impossible.
For the upper set, you just need to select the matching color to the lowers you have ordered. Install them all at once, or the lowers alone for a while, then the uppers. You cannot order the uppers without the lowers though as they will no mount correctly. The upper crash bars protect important radiators and bodywork. Essential in the event of any kind of crash. These also make excellent mounts for auxiliary lights for added visibility.
Included with each piece you receive a complete set of instructions and all mounting hardware required, in typical Givi fashion.
NOTE: The upper units REQUIRE the lower crash guards for proper mounting and are not a stand alone item!
Please Note that these Crash Bars are also compatible with the Givi Skid Plate.
Repair kit for your rear disc brake master cylinder.
This kit includes a 320mm Wave rotor, caliper relocation bracket and new Galfer semi-metallic brake pads.
You can add a Stainless Steel brake line, and DOT4 fluid to your package.
Lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.
Stock spring rate 0.60 kg/mm
Race Tech Recommends 5w oil, 2 qts to reach 110 mm oil level.
In stock form, the forks, featuring a single spring design are under sprung for any rider over 100 pounds. With limited travel, adding a stiffer spring in the right leg only per the stock design was not a viable option.
Race Tech instead offers a High Performance Spring Kit that adds a stiffer spring to the other fork. (The overall spring rate in the forks is the average spring rate between both legs.) This upgrade will make a drastic improvement in handling for most riders.
0.50KG/MM KIT
Included in this kit are .42 kg/mm fork springs, Cogent DDC (Drop in Damper Cartridge) performance cartridges and two bottles of 5w fork oil.
Developed by the KLR suspenison experts at Cogent, this set of springs will stiffen up that wimpy KLR front end. Choose between .64 kg/mm springs (60% stiffer than stock) or .70 kg/mm units (75% stiffer than stock).
Will not work for 2014-Cur 'Mid-Year' New Edition Model
These springs are custom wound specifically for the XT225. Stiffer than the .36 kg/mm stock springs, these will make your front perform significantly better. Combine them with the Cogent DDC's and you will be very happy with the results. Sold as pairs.
The Pro-Series is an excellent replacement for the stock shock. With both compression and rebound adjustable as well as preload adjustable, you can tailor the performance to match your riding style. Compact and rigid design with piggyback type reservoir specifically engineered for your WR250R. Fully serviceable shock is designed for the long haul.
Select the spring you want installed based on the load you plan to carry. Choose the 'standard' 8.15kg/mm spring for rider/ luggage up to 220lbs. Weigh more than 220 lbs, or are loaded to the max, think about the 10.19kg/mm 'heavy' spring.
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.
This spring is 8.0kg/mm
OEM spring rates are 5.7-7.6kg/mm progressive style.
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. No disassembly of your forks, no drilling of damper rods. Just change the oil to 5w and install the DDCs under the springs and hit the trails.
Stiffer fork springs are required to realize the full benefits of the DDCs. .42 kg/mm springs are the springs recommended for just about anybody out there. Please call if you have any further questions.
The DDCs are not recommended for use with progressive springs.
The DDC Install/Removal Tool which makes installation that much easier.
Adjustable lowering links by PSR. Adjusts the rear suspension from stock height to 4 inches lower.
Stock suspension suffers from poor compression damping and limp rebound damping. The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.
Seat Concepts dual-sport/adventure seat-kits incorporate a wider seating area for the rider, which results in more even weight distribution, while reducing pressure points. Each individual seat model has been specially designed to increase comfort without compromising ride-ability. The more aggressive the bike, the more aggressive the seat-kit.
Each kit contains detailed instructions for easy "Do It Yourself" installation. This provides the highest level of quality & comfort at an affordable price.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
| Width: | 9 1/4" (235mm) |
| Height: | Same as OEM |
Note:
This seat is based on the off-road version of this bike. The street version is 1 inch lower than this seat.
Will NOT fit DRZ 250
New wider seat to help keep comfortable on that long commute or dual sport ride. The added width and foam density will help keep the seat from being an item to stop you from going on that ride or enjoying the bike.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
| Width: | 10.5" (267mm) |
| Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is higher quality than OEM seat foam. Their proprietary formula is plush, while still offering the necessary amount of support.
Their unique comfort and shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!
The Complete Seats come assembled with an high quality aftermarket pan and are ready to ride.
| Width: | 9 7/8" (251mm) |
| Height: | Same as OEM |
This Comfort XL seat design is roughly 3" wider overall than their standard comfort seat. This means more surface area, better weight distribution, and added comfort for those not worried about seat width.
Available as Complete Seat only. The Complete Seats come assembled with an aftermarket pan and ready to ride.
| Width: | 11" (279mm) |
| Height: | Same as OEM |
Maxima light viscosity 3w 75-390 shock oil, 1 US Quart.
Designed to enhance the appearance of your TW200, yet provide greater riding distance per tankful. This larger fuel tank has double the capacity of the stock tank at 3.6 Gallons, yet very slim and sleek. This tank has a custom design that will allow the use of OEM & Maier side covers. These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.
Comes with New Screw Cap.
Requires OEM/Stock petcock and oval rubber grommets for install.
If you do not have the grommets or if your O.E. grommets are in poor condition you can add these to your tank order.
A new high output stator for the XR650L. 25% more output than the stock unit. Approximately 50 additional watts. Now you can have enough power to run those driving lights and/or heated riding gear!
Antigravity Batteries introduce the ground-breaking "RE-START (RS)" line of batteries. These are the first batteries with built-in jump starting! They intelligently monitor their status, and just before going completely dead, puts itself to sleep with just enough energy to get your vehicle started again. Simply press the RE-START button located on the battery, then start your bike and ride away!
These are an extremely lightweight (2.3 lbs.) and high-powered Lithium-Ion replacement battery for motorcycles. These batteries offer the first Battery Management System (BMS) found on a powersport battery and includes low-voltage cut-off, over discharge, over-charge, and thermal protections with real time lithium-ion cell balancing. Highly recommend using a lithium charger to maintain the life of the battery.
3 Year warranty
Product Size is just 5.9"L x 3.5"W x 3.74"H. If you need spacers, select the optional Foam Kit to pad the battery in the battery box.
The Shorai LFM Standard Recommendation is the best overall pick for most applications, and has been selected to give strong cranking performance and long lifespan.
Measures 4.45" x 3.5" x 2.28"
Weight (lbs): 1.52 lbs
Weight (kg): 0.69 kg
Cold Cranking Amps: 210
Polarity: [+ -]
Each Shorai battery includes self-adhesive foam panels to achieve a snug fit in your battery box.
Stock chain guard crack and crumble on you? Won't happen to this unit CNC machined from 2.5mm marine grade aluminum. Polished to a beautiful sheen that will give your DR that little twinkle as well as better protection.
Replace these any time you feel excessive play in the sprocket hub.
Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.
Sold as a full set.
Choose 17" Supermoto, 19" Adventure or stock 21" front wheel. All work with the stock DR650 speedometer and cable on either the stock or Warp 9 hub.
Warp 9 Supermoto wheels are built with billet hubs, 7000 series aluminum rims and laced and trued with stainless steel spokes and nipples.
The 3.5" x 17" front wheel includes a 320mm brake rotor and caliper relocation bracket.
The 4.25" x 17" rear wheel also comes with a rear brake rotor already mounted.
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
Rear wheel Includes Sprocket Carrier with 525 40T Sprocket installed that matches selected hub color.
A six step maintenance system designed to recharge any K&N air filter.
Changing tubes or tires without the right tools can be a real chore. Don't fight your snug beads any longer, use this 27" long tool that opens to 7-3/4" to provide the leverage you need to easily break your tire bead. Constructed from heavy-duty steel with comfortable no-slip grips, this tool makes the job a snap.
A compact and lightweight solution to eliminate the SNAP for a safer tow. If you have ever towed a motorcycle you are familiar with the snap that comes with a traditional tow strap. GCAG made the Dynatow with a section that gives 32 inches of stretch so both riders have an easier tow.
The 26 foot total length gives you enough room to maneuver around obstacles and allows the freedom to choose better lines if you are towing in the gnar.
You can also use this as a recovery strap. You can girth hitch the loop end to the bike and throw the other end to a friend to pull. The dynamic properties of the Dynatow will help assist the pull. All of this functionality fits in a flat pouch about the size of sandwich and only weighs 12.8 oz. Throw it in your bag and be prepared.
Specifications:
Please consider the following before use: Practice before you need to use this product. Always inspect your Dynatow strap before use and NEVER use a worn strap. They recommend a proper training class to learn safe methods for towing a motorcycle.
The Giant Loop Tow Strap is a multi-functional tool that helps get you or your riding friends out of sticky situations.
This Cordura® Ballistic tow strap, designed with sewn loops on each end, can be girth hitched around a tree, bumper, rock, etc.; or used with footpeg-to-footpeg or other motorcycle (and snowmobile, ATV, snow bike) towing techniques. Constructed in the USA from ultra-durable custom woven Cordura® Ballistic webbing, which folds up into a compact integrated cover made with 22 oz. vinyl-coated polyester, or what they like to call “truckers tarp.”
Doubles as a quick deploying, super-strong ridge line for pitching a shelter tarp.
Color may vary based on manufacturer availability, quality will not be compromised.
3.5MM X 20FT
Made from Tough but lightweight 12 Strand SPECTRA / UHMWPE
2200LBS Break Strength
Double Looped Ends
Each Looped end is Covered in a Kevlar Sheath to protect the rope from abrasion
The GCAG handles are comfortable to pull so whoever is helping will pull harder, and they are soft against your fender so you won't have any annoying bouncing, noise, or graphics damage.
GCAG dirt bike lift strap handles are constructed of 1" thin nylon webbing with flat stainless steel tri-glides for attachment. The grip section is built with 1" climb-spec tubular nylon webbing and a comfort grip handle.
Features:
Similar to our Adventure Shirts, this super soft hoodie features our logo on the front and our Topo design on the back. Perfect for those cool evenings or brisk days.
