Spring time is in full swing here at ProCycle. With these busy days please be sure to let us know if your order is time sensitive. We try to do as much as we can to accommodate your upcoming trip.
This tool helps ease the pain of accessing the neutral safety switch. This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub.
Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut a breeze, and minimizes the likelihood of damaging the clutch hub.
Replacement retaining pin for the brake caliper. Includes 1 stock style brake pin.
(Front caliper only for DR350 and DR650)
Be sure to use some anti-seize on the threads when you install it.
Contains genuine KEIHIN parts to rebuild your FCR41 pumper. Fresh o-rings and float needle insure you don't end up with a crank case full of fuel.
Not for the stock carburetor. Fits FCR41 conversions only.
Pro Moto Billet Cargo Racks are brutishly strong, functional, and they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum. Available in silver only.
Note: Placement of this top rack does require removal of the stock tool bag.
Genuine Honda replacement exhaust gaskets.
CNC machined from 6061 Aluminum by the crew at Warp 9. This upper triple clamp will help to get the bars out of your lap on the XR650L. It allows for six different bar positions (three mount positions and reversible offset mounts). Uses the stock key switch and works with the handlebar lock. Speedometer and indicators all use mounting positions as well.
This clamp comes with 1-1/8" handlebar mounts.
High quality aftermarket paper gasket.
Plenty of fuel capacity for those long rides. This top quality Acerbis fuel tank will get you there and back again.
Sintered Pads are best for regular riding. Long life, and good performance in all conditions
Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
Race Sintered are designed for racing use
Includes front and rear brake pads
Throttle cable routing on the XR650L gives you very little extra slack for raising the bars or adjusting them towards the rider. We now offer throttle cables that are 3" longer than stock allowing you to customize the bar position to your riding style.
These quality cables are made by Motion Pro.
Quality replacement rear fender from Maier.
DG Performance exhausts help your engine breathe better, resulting in increased throttle response, power and torque.
The V2 Series Slip-On muffler features:
Standard sound level is approximately 98 db and quiet core inserts are available separately.
This Lightweight Slip-On weighs approximately 5.5 lbs and bolts directly to the stock headpipe.
It is equipped with a US Forest Service-approved spark arrestor.
Double the size of your side stand footprint and half the chances of your XR650L tipping over when parked on soft terrain. This laser cut, TIG welded 0.190" thick slice of aluminum bolts to your machine with just the addition of a hole in the stock side stand pad. Just takes minutes to mount! All hardware provided.
We start with Excel or Sun rims, OEM hubs, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.
Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
The Trail Tech Vapor Speedometer/Tachometer units are custom designed for an exact fit. They feature a bright white backlit LCD display, waterproof connections, and all parts needed for a complete installation. These units accept AC and DC power input, and automatically switch to internal power if external power is removed. Power connectors are included. Permanent solid-state memory guarantees that data is never lost, even without power. Units are available in black.
Trail Tech provides a one year warranty and unlimited free phone and email support.
Unit functions:
A 10-pack of drain plug sealing crush washers. Replace your sealing washer at every oil change to prevent a leak.
Fork brace precision machined from aluminum barstock. Drilled and tapped for optional lower fender attachment.
Hard anodized black for corrosion protection. Fits OEM forks. Split design allows for installing in minutes without having to remove the forks.
Providing unbeatable performance and exceptional value, Hi-Flo is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide.
Get better range from your XR650L by adding a Clarke 4.7 gallon fuel tank. Cannot use stock shrouds.
Available in Natural, White, Black, and Red. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap, uses stock petcock.
50mm step width provides better grip and control
This DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.
This kit is highly recommend over the non-DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!
Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.
Race Tech has developed these straight rate springs specifically for the heaviest loads.
PSR has a new shark fin rear rotor protector for the big XR and XRL. CNC machined from forged aluminum and then anodized gun metal in color. This unit bolts to the stock caliper bracket.
If you need a replacement cap for your Acerbis tank, why not go bling? These caps have a carbon fiber pattern molded into them that is extremely realistic. Looks like the real thing. Topping off the cap is a CNC Machined metal vent cap. This eliminates the need for a lengthy vent tube that gets in the way. The vent cap allows air to vent into the tank but does not allow fuel to splash out during normal use or during a tip over.
These caps fit Acerbis tanks only.
Now available in the original version or the Ultra version. The original uses the front two emitters for low beam and then switches to the rear two emitters for high beam. The Ultra uses the front two emitters for low beam and then runs all 4 emitters on high beam at a reduced wattage. Wattage is 38 watts on low and 38 watts on high.
This bulb uses 4 Cree XHP 50 emitters, capable of more than 2500 lumens each. At 5000 lumens on each function, this is the brightest Cyclops H4 bulb.
*UNIVERSAL PART, PLEASE CHECK YOUR APPLICATION FOR FITMENT
Kit includes all the fork bushings, o-rings, snap rings and washers this kit comes with what it needs to completely rebuild your front fork bushings
All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.
Made by Nissin, an OEM supplier in Japan
This optically clear headlight guard is CNC cut for a perfect fit. It is made of durable aircraft grade 3/16" thick cast acrylic which resists harsh rock impacts, trail scuffs, and incidental scratches. Velcro fasteners hold the guard firmly in place and allow for easy on & off should it need an occasional cleaning. Installation is a quick five minute job, positioning template included.
This is a high-quality seat cover done by Moose for the XR650L. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam.
For LED Auxiliary Lights
From our friends at JNS Engineering, a very nice mount for a set of auxiliary lights on the front of your XR650L. Laser cut from 0.190" 5052 aluminum it is CNC formed and then powdercoated black. (image shows bare aluminum, but yours will be black) One of the best benefits is that it will not interfere with even the largest aftermarket fuel tanks. Includes stainless steel mounting hardware.
Progressive Suspension springs offer a soft initial spring rate for a plush ride. Progressively wound design provides increased resistance to bottoming as spring compresses. These springs are significantly stiffer than the wimpy stock springs. Spring rate spans the .45-.62 kg/mm range.
Sold in pairs
This carry rack is solid and durable made from 5052 aluminum and with its sleek design it will not catch on your clothes or nature. It is an easy install and will allow you to strap your cooler, lunch box, tools, extra gas can, or whatever on the back of your bike. Comes complete with all hardware and easy install instructions.
Top suspension performance requires firm bottoming resistance with plushness at the same time. Even the best suspension tuners can only make the stock valving design work so well. The Gold Valve Shock Suspension System is a proven bolt-on shock valving system that improves control, traction, performance and bottoming resistance.
High grade aluminum alloy front disk guard is the ultimate in front disc protection!
This is the brace needed to stabilize the big front fender on the XR650L. This simple bolt-on brace reduces wind buffeting at highway speeds. It also helps carry the weight of a fender mounted tool bag.
Made from laser cut 5052 aluminum, then CNC formed and beautified with a shiny black powder coat. Easily mounts in a few minutes using the included hardware.
Fresh O-rings to ensure your XRL stays oil-tight and leak free. The Oil Change O-Ring kit includes a filter cover O-ring and a filler plug O-ring.
A high quality top end gasket set for the XR650L
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of the big Acerbis or Clarke tank? The 4.0 gallon tank from IMS might be just right. Includes cap, uses stock petcock.
Protect that vulnerable rear master cylinder with this thick aluminum guard from JNS Engineering. CNC laser cut then formed and given a clean black powder coat finish. Includes new button head screws and aluminum spacers.
FunnelWeb ProLine Filter Highlights:
Like all FunnelWeb filters, the ProLine Filter features profile cut, single layer, single density foam that doubles the external surface area of the filter without increasing the original filter size. The ProLine Filter traps dirt, dust, sand and mud over a larger area on its outer surface, ensuring optimal air flow is maintained for maximized engine performance and reliability.
The single layer, single density polyurethane foam has the added advantage of being easy to clean and the ability to maintain its original shape after numerous washes. Overall, compared with conventional foam filters, FunnelWeb offers more protection from dirt ingestion, has longer service intervals and maintains high airflow rates when dirty.
Now you can have minimum output shaft wear, minimum chain drive wear with the FRITZCO DRIVELINE sprocket. The design of their sprockets provide correct chain alignment, allows for full spline contact with the XR650L's output shaft, fit the counter shaft either way, and straight up no hassle installation with the OEM two bolt retainer and fasteners (except 13 tooth that comes with it's own quick change retainer). Their sprockets are machined from alloy steel that is comparable in every way to OEM Honda and the best offered by other manufactures. The sprockets are then given a heat treatment that provides a compatible sprocket for the Honda output shaft and longest wear life possible.
A way to double the sprockets life would be to have a sprocket that fits on the shaft either way so both sides of the teeth can be used. Bear in mind you can't wear one side of the teeth all the way through, then flip the sprocket, and expect double life. You must reverse when a normal wear pattern develops.
A 16 TOOTH SPROCKET IS THE BIGGEST FRONT SPROCKET THAT WILL RUN WITH THE STANDARD 110 LINK CHAIN AND 45 TOOTH REAR SPROCKET ON A XR650L* THE OEM COVER WILL REQUIRE MODIFYING TO USE THE 16 TOOTH SPROCKET ON YOUR XR650L.
Has your TM40 carburetor been sitting for too long and now needs to be rebuilt? Then what you need is this TM40 Rebuild Kit that contains Genuine Mikuni replacement parts.
This kit includes:
The DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 89db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.
You may want to consider a new exhaust gasket that goes between the header and the muffler.
Wider foot pegs for sure-footed comfort. Cast stainless steel.
Our own jet kit for the Mikuni TM40 carburetor.
Includes new main jets, pilot jets and a new needle with e-clip.
Comes with a printed Mikuni tuning manual and a jetting suggestion chart.
Not for the stock carburetor Fits TM40 conversions Only
Kouba lowering link will lower the rear suspension 1.75". Comes with bearings and seals installed for a quick and easy installation.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
CNC machined from 6061 Aluminum by the crew at Warp 9. This upper triple clamp will help to get the bars out of your lap on the XR650L. It allows for six different bar positions (three mount positions and reversible offset mounts). Uses the stock key switch and works with the handlebar lock. Speedometer and indicators all use stock mounting positions as well.
This clamp comes with 1-1/8" bar mounts that work perfectly with the tapered handlebars included. Then there is a new set of ProGrip 714 Rally Grips.
Replacement Acerbis left-hand side fuel tank petcock.
For Acerbis tanks only.
This anodized billet piece, brings a touch of color to your bike. Available in red or blue, it replaces the stamped steel clevis that connects your brake pedal to the master cylinder.
Iridium spark plugs are made with premium quality materials.
Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.
Sold individually, unless otherwise stated.
Patented fork seal features a balanced 3 lip design that evenly distributes the pressure reducing operating temperature, wear and friction
Custom Elastomer Fork Seals have been tested to outlast OEM fork seals. Extends typical seal life by 3 to 5 times over OEM seals
Stiction (friction) measures from 1/3 to 1/2 less than OEM seals for smoother fork action
Lower Stiction, Longer Life! It doesn’t get any better than this!
Plus, the only complete line of dust wipers! Wipers should be replaced with the fork seals to assure peak performance.
Kit includes Fork Seals and dust wipers.
Did you snap a headpipe bolt on your XRL or are your headpipe bolts looking a bit dingy and rusty?
These replacement header exhaust stud bolts are made of super corrosion resistant 316 stainless steel. They provide excellent resistance to chemicals and saltwater to give your exhaust system a hassle free service life.
If you've got an older XR650L, you know the struggle of removing the O.E. nuts from the studs. They either snap, remove the stud or come off as they should. At some point you're likely to snap on or come across a seized nut to stud. These bolts are a superior upgrade to the O.E. nut and stud.
Kit includes: 4 Stainless Steel bolts
Geared for the do-it-yourselfer that already has a TM40 or HS40. This kit supplies everything you need to convert it for use on your bike.
Kit includes intake and air boot adapters, throttle cables, choke knob, accelerator pump nozzle, a wide selection of main and pilot jets plus a TM40 tuning manual.
A replacement Clarke Gas Cap that fits most Clarke Gas tanks. Comes with rubber gasket.
A high quality replacement clutch cable.
Full braking power for your XR650L supermoto conversion. Floating EBC 320mm brake rotor with gold anodized alloy carrier. Includes caliper relocation bracket.
Stage 1 - Excellent mid-range and top-end power increase.
Uses stock valve springs and rockers.
Does not incorporate compression release.
Silver in color
Upgrade your bike with a tapered 1-1/8" bar. Constructed of Aircraft grade 7065 T-6 aluminum that tapers to a standard 7/8" to accept stock controls.
These hand-crafted bash plates from B&B Eng. are constructed from 4mm 5083 aluminium plate. Strong and lightweight, this material has been selected because of its extreme suitability for welding, abrasion and impact resistance. All the necessary stainless clamps and bolts are included. Plate has a polished finish with foam or rubber where required.
All the advantages of a flatslide pumper carburetor at a much friendlier price than a Keihin FCR.
Our complete genuine Mikuni TM40 pumper carburetor kit comes with alloy adapter rings bonded to the carburetor body for a firm reliable fit in the stock air boots. We also include new 3" longer than stock throttle cables, a remote mounted choke knob, complete instructions along with a wide range of main jets and pilot jets for fine tuning or to accommodate bikes with extensive modifications.
Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty. Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever!
The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels.
Optional Heat Shield Strip will protect your airbox from the close proximity of the hot head pipe.
Quality replacement front fender from Maier.
Each kit includes all necessary rubber components and brake pins.
Softer return spring for your TM40 carburetor.
This replaces the stock return spring that comes with the TM40 carburetor creating a 25% lighter throttle feel.
Quality steel front sprockets. Choose 13T through 15T. The stock size for the XRL is 15T. Go down in tooth count for faster acceleration.
Pegs that are designed for real adventure, providing a level of comfort not seen with other pegs. 2.25" by 3.5" makes for a platform that you can stand on for long periods with no worries. All necessary parts included for a direct bolt-on application.
Available in a beautiful anodized black or clear aluminum for durability and protection from the elements.
Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat.
Comfort Cell Foam retains resiliency and doesn't crush down like the stock foam so they can build a lower seating platform. This gives you better ground reach and a lower center of gravity. For the off-road enthusiast they were sure to leave enough nose to allow you to slide up the tank and get through the corners faster. Or slide back to skim the front end over the whoops.
As you're seated, the bones in your posterior that take most of your body weight are roughly seven inches apart. Your stock seat at its widest point is 8". This actually makes the foam of the stock seat crush in and applies pressure to the center of your body. The Corbin model is a full 11" and is built with denser, sculpted foam that supports your body weight over a greater area and equalizes pressure. If you consider actual seating surface, the Corbin model gives you over 200% more body contact! Long story short, greater riding comfort!
On the top, they cover it with only the highest grade of weather resistant materials for durability and long life. To add a bit of flair, they offer an embossed material in a variety of colors that gives the look of Carbon Fiber (they do not recommend using leather in these saddle models). Shown here with Black Carbon-Fiber seating, Asphalt sides and Tomato Red welts.
Saddle mounts similar to stock with two bolts into the chassis. In order to provide a closer fit to the bodywork and tank, it is necessary to mount the supplied seat bracket to the bike first, then mount the seat to the bracket. Illustrated instructions can be found here.
The default vinyl choices are black 'carbon fiber' on top and 'asphalt' on the sides, 'no welts', black logo. You can view all of the available materials and colors through the link below. If you would like your seat built with something other than the standard choices please state specifics in the comments during check out.
These Mikuni carburetors are correctly sized and easily fitted to your Honda XR600 and XR650L stock motor mounting flange after removing the locator tags and also match the air box when using the silver anodized air-box adapter. This adapter is fitted prior to delivery when purchasing complete kits. For this Mikuni carburetor to operate correctly the motorcycles air box must be opened up to allow more air flow in. Using a hole saw, a 45mm diameter hole will be sufficient for a Suzuki DR650 but some Honda’s require way more. The best process is to keep opening up the air-box until no more improvement is noticed and you will be surprised at the difference. The kit also comes with throttle cables and a 1/4 turn quick action throttle which must be lubed before fitment. The carb comes with a couple of Honda specific adjustments made and pre jetted for your engine. A specially made size 30 pump nozzle is fitted as the accelerator pump circuit on TM42 carbs will not work properly on Honda’s or Kawasaki’s without it.
Climate, altitude and fuel density from different octane fuels all have varying effects on final fine tuning as does cam, exhaust and cylinder head porting etc. For this reason, we have included what we have found to be a range of jets to allow you to tune to most variables.
This carb fits with most aftermarket large capacity tanks. Some larger capacity tanks do not allow the fitment of this carb without modification. A competent person can easily heat and depress the contact area around the throttle mechanism allowing for clearance on problem tanks. Polyethylene tanks start their life as lump of poly that when melted evenly spreads itself around a rotating mold, to later carefully heat with a heat gun any section of a tank and change the shape has no effect on the integrity of the poly itself unless pushed too far, thinning it. We recommend having this professionally done for the reason some people may neglect to properly remove all the fuel from an existing tank or if not competent may make a mess of it.
Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.
The RS-2 is a potent and versatile design that evolved from our original TRC, engineered to provide increased power and power delivery. With a different pyramidal shape that features increased volume, the RS-2 is a quieter system with a larger core - and it offers the added bonus of outstanding performance in a value-priced package.
Designed for use with stock engines using either stock or aftermarket exhaust and air filters.
The ultimate factory activated lead-acid battery upgrade from stock.
40% more amp-hour capacity and 70% more cold cranking amps (230) than the stock battery. This is a genuine YUASA battery. Lasts longer and has increased vibration resistance. Ships pre-filled, sealed, and ready for use.
Note: This battery is taller than stock. The factory battery strap cannot be used to secure it. Factory-activated batteries should be charged once a month when not in service.
Dimensions: 6" x 3-7/16" x 4-3/8"
Weight: 8.5lb
12V/11.2AH 230cca
Positive terminal location: Left Front
E3 Resistor Spark Plugs
A stiffer shock spring will help you get through the whoops or just help handle that extra baggage on the rear.
Stock spring rate is 10.5 KG/mm
*Spring color may vary due to specification requirement and availability.
We start with an Excel rim, OEM hub, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike. Optional upgrades include SUN rims available in 3 colors.
Our pro shop then laces and trues your wheel to perfection, giving you the highest quality custom wheel available.
Add a tire to your wheel order and we will throw in a tube and mount and balance it at no additional charge.
All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.
Made by Nissin, an OEM supplier in Japan
Extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!
Two feeler gauges on a single tool. Angled to make checking the clearances easier.
Stock valve clearances are .004" intake and .005" exhaust (.10mm int. and .13mm exh.)
Mount Barkbusters standard aluminum bar handguards to 1-1/8" motorcycle handlebars with the Barkbusters 1-1/8 inch (28.5mm) handlebar saddle clamp set.
What's in the box:
Want an amazing increase in throttle response? More power over a much wider range? The Keihin 41mm, FCR style carburetor does all of that plus runs smoother at lower RPMs and pulls taller gearing with ease.
This kit is available with a choke circuit and a version without a choke circuit.
Both kits include everything needed for a simple bolt on installation - a genuine Keihin FCR41 pre-jetted flat slide carburetor, Motion Pro push/pull throttle cables and airbox adapter. Bolts right up to your OEM airbox fitting and intake manifold.
You cannot add a choke knob to the non-choke version!
An excellent replacement for the stock fork boots. These are great for protection from dirt, rocks and other contaminants. These boots utilize the latest advances in material technology to adapt to fork and styling demands. These high quality fork boots are 1/4 the price of the OEM factory replacements.
Choose black, blue or yellow.
Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position.
The Firepower features increased cranking amps over lead acid batteries and has a very fast recharge cycle, and can be brought up to a 90% charge within 6 minutes. It also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.
165 CCA 12V/36WH
Package Dimensions: 6.20 x 3.70 x 4.45
Moose Racing seat for us XR650L riders. This is a complete seat already installed on a new seat pan. Take your old one off and put the new one on and get back to riding!
Custom made push/pull cable set for the Honda XR650L.
These are for use with the stock throttle assembly, when mounting a Mikuni push/pull pumper carb, or Keihin FCR series carburetor.
Available as +3" and +6" over stock length, with stock style throttle side fittings.
Sold in a set as shown.
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
Steel braided lines have a Teflon tube as a core wrapped with a stainless steel wire braided exterior which doesn't allow the brake lines to stretch under pressure like stock rubber lines do.
The benefit is a firmer brake lever with better feel because the energy that was going into stretching the stock lines now goes straight to the brakes.
The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.
You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.
Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.
There are many options and configurations using this electronic tool.
No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
The Complete Seat comes with an aftermarket pan with the foam and cover kit assembled, ready to ride.
| Width: | 11 1/8" (283mm) |
| Height: | Same as OEM |
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
12mm Thread, 17mm Head.
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
10MM Thread for frame drain.
Simple, lightweight rack made from rugged 1/8" 5052 Aluminum, with a rigid 5-point mounting system.
Low profile allows for easy seat removal.
Features:
Note: Placement of this top rack does require removal of the stock tool bag.
An OEM type replacement for the mighty XRL from the folks at Fuel Star. Single inlet that threads directly onto the stock fuel tank. Also works on the adapters that come on some aftermarket large capacity plastic tanks (like IMS).
Kit comes with a new Petcock, O-Ring, Fuel Line and Fuel Line Clamps! Everything you need for a complete fuel connection replacement.
Genuine KEIHIN replacement parts for your FCR41 pumper carb. Ensure your beast is getting fed when it needs it!
Not for the stock carburetor. Fits FCR41 conversions only.
