Search Products

A quality replacement speedometer cable

CNC machined from 6061 Aluminum by the crew at Warp 9. This upper triple clamp will help to get the bars out of your lap on the XR650L. It allows for six different bar positions (three mount positions and reversible offset mounts). Uses the stock key switch and works with the handlebar lock. Speedometer and indicators all use mounting positions as well.

This clamp comes with 1-1/8" handlebar mounts.

OEM throttle cable set for the CRF250L

*generic image, actual cables may look different.

Replacement shift lever from IMS with folding tip.

Genuine OEM replacement choke cable.

Spare replacement throttle cables for your TM40 carburetor conversion. Fits the stock throttle housing.

These are new premium low-friction cables. They will also work with the OEM Suzuki BST40.

Original Suzuki factory replacement levers for your DRZ400S/SM/E

Suzuki makes it almost impossible to replace your stock grips. It's much easier with a new throttle tube. Removable end cap for bikes with hand guards.

First there was the Warp 9 "4-Finger" Lever, now there is the Warp 9 "3-Finger" Lever Exclusive to ProCycle. Yep, the original shorty (next item below) is a full 4-finger type lever. These are a full half inch shorter. You asked for 3-finger levers, and we had Warp 9 make them for us. Brake lever includes a nice billet clamp with nylon sleeve to allow the assembly to rotate on impact. Will not fit with the stock OEM wind deflectors.

Will not engage the clutch switch on 2010 and later models

A set of replacement brake and clutch levers. Standard length. Sold as a set.

Please notice that there is a difference in sets from '90-'09 and from '10-current!

Late model levers currently unavailable

Mount these polished billet aluminum spacers under your handlebar clamps to raise your handlebars 1 inch. High quality longer bolts are included.

Forged aluminum, black anodized arm and Knurled CNC aluminum shift tip.

A quality set of replacement throttle cables from Motion Pro

A set of polished aluminum replacement brake and clutch levers.

This is the evolution of taking the proven GPRV1 steering damper and locating it under the handlebars. Mounting the damper unit under the bars allows for addition room on the top cross-bar or bar mounts.

This GPR setup is a good choice for the weekend warrior to the race professional that would like to raise the handlebar height. Perfect for desert and off-road GPs.

The MAGURA HYMEC hydraulic clutch system gives you an ease and smoothness of pull that cannot be equaled by a cable unit. No need to lube the cable, no more broken cables. The HYMEC is simply a fantastic hydraulic retrofit clutch system. You will be able to get away with applying a lot less pressure than with a standard cable clutch. Depending on riding style, this can make for huge benefits in terms of riding comfort and control. The master cylinder control naturally has reach adjustment.

The advantages of the MAGURA hydraulic clutch are many:

• Forged lever with improved lever ergonomics
• Filled and delivered ready to install
• Easy to install, detailed instructions included
• Less energy required
• Fine response
• Finely tuned metering capability
• No fluctuation in the pressure point
• Maintenance free
• First class workmanship-"Made in Germany"

MAGURA favors use of their 'MAGURA Blood' for its clutch systems. Mineral oil is non-toxic and not hygroscopic. Regular changes of the clutch fluid are not required.

Here is the little switch that mounts inside your brake or clutch lever perch and controls the brake light or clutch safety circuit. This switch often gets damaged in an unplanned dismount (aka: crash) or the plastic simply cracks from age. When this happens, you can find yourself chasing a short circuit that keeps blowing your fuse every time the brakes are applied. If this has happened to your TW, here's the fix!

Forged aluminum, black anodized arm and Knurled CNC aluminum shift tip.

Order up your new levers here! If you keep breaking levers, you might want to think about a set of handguards to protect them in case of a fall.

• Machined and knurled 6061 billet aluminum
• Removable end cap for easy handguard installation
• Works with standard housing

Did you fall and break your shift lever on your TW200? Replace it with a quality Moose shift lever.

Warp 9 Flex 3-Finger Levers are machined Billet, anodized and hinged levers with CNC machined master cylinder interfaces.

Adjustable reach allows customization to the rider's hand size.

Double hinge design allows lever to flex out of the way in most impact situations.

Pushrod or Bearing contact styles for smooth modulation.

This rotating shift tip provides 6 different positions, offer more sensitive shift position adjustment. Shift arm is made of A2014 forged aluminum for durability and is black anodized. Foldable shift tip is made of CNC aluminum with knurled finish for better shift grip. Replacement shift tips and tip mounts are available.

The GPR v5 is the fifth generation steering damper.  Its compact and slim design allows for the damper to be mounted below the handlebars, out of harm's way, without raising the bars more than an inch.

V5-D Fat Bar kit – A Sub mount kit, mounts below the handlebars. Uses the low-profile GPR V5d dirt bike stabilizer in a cradle-style handlebar mount and bolts to the stock triple clamp. Will raise bar height about 1".

These kits include the GPR V5d dirt bike damper, handlebar mount, frame bracket and all mounting hardware.

Givi Smart bar for attachment of electronics.

Bike specific mounting hardware (sold separately) required.

• Fit models with a 1 1/8" stem clamp and a 1 1/8" handlebar
• Handlebar clamps can be pivoted to desired fore and aft location to achieve ideal riding position
• Engineered and tested for maximum strength and durability
• CNC-machined from billet 6061-T6 aluminum, then anodized for long-lasting good looks
• 2" center to center rise above stock position

• Lightweight levers are CNC-machined from aluminum
• Reach to the lever is adjustable to six positions

• Lightweight levers are CNC-machined from aluminum
• Reach to the lever is adjustable to six positions

• Knurled folding tip reduces crash damage and helps prevent snags
• Fit like OEM

• Alloy levers allow two-finger control of the brake and clutch
• Set includes brake and clutch short power levers
• Each lever set is poly bagged and labeled for easy identification
• Levers only; perch not included

- Pivot CP clutch and brake lever set for Trail models.
- Lever folds outward to prevent breakage in the event of a crash.
- Lever adapter is ultra precise CNC machined out of high grade aluminum for super light weight design.

• 6-way adjustable
• Available in short and long versions
• Large radius lever surface
• Improved ergonomics and rider comfort
• Laser engraved Vortex logo

• 6-way adjustable
• Available in short and long versions
• Large radius lever surface
• Improved ergonomics and rider comfort
• Laser engraved Vortex logo

• The new 3rd generation Motion Pro Revolver variable rate throttle system is here!
• Innovative reel changing system lets you tailor the throttle rate to your preference and riding conditions
• 5 different reels provide perfect throttle response for any condition. Use smaller reels for slower throttle rate and larger reels for faster throttle rate. Included cam reel provides progressive throttle response preferred by some riders
• Slim REV3™ throttle housing allows more room for lever clearance and adjustment to throttle housing position
• Improved throttle stop provides greater strength and durability
• Snap together elbows makes it even easier to install and change reels
• Cable boot keeps dirt and dust out for reliable and smooth operation
• REV3™ off-road kits are compatible with the new Motion Pro DirtControl™ V2 Lock-On grips and ODI Lock-On grips
• Billet aluminum inline cable adjusters ease installation and adjustment
• Lower section of cables use 5 mm housing with PTFE liner for reduced friction, increased routing flexibility and lighter weight
• Upper section of cables use 6 mm housing to provide solid support of adjusters
• Simple to install and maintain
• Patented

Kit includes:

• REV3™ throttle assembly with throttle tube (REV3™ off-road kits include the unbreakable Titan Throttle Tube™)
• Motion Pro REV3™ black vinyl cables specifically designed for your bike
• REV3™ sportbike kits include Motion Pro RoadControl™ grips
• Four interchangeable round reels: 35 mm, 40 mm, 45 mm, 50 mm
• Progressive cam reel - Sportbike kits include road race profile cam reel (orange)

A set of replacement brake and clutch levers. Polished alloy.

• Tool-less cable adjuster
• Machined billet aluminum with a durable anodized finish
• M8 x 1.25 thread

• CNC-machined from aerospace quality 7075-T6 aluminum alloy
• Handlebar clamps included
• Adjustable bar clamp mounting position
• Easy to install; pre-pressed Pivot Works lower bearing included
• Developed in collaboration with top US MX/SX and MXGP teams
• Torque settings etched on the clamps
• Greater rigidity
• Anodized finish

• Manufactured to exact measurements to meet or exceed oem specification
• Tempered steel wire housing with an inner nylon sleeve for long life & smooth operation

• Handy, compact kit for on-the-go emergency throttle, clutch and brake cable repairs
• Includes 2 different diameter 6.5 long inner cables and an assortment of cable ends

Replacement steel shift lever with folding tip

Quality replacement clutch cable.

• Nylon-lined housings and precise OEM component dimensions

Quality replacement levers. Standard length.

These heated grips from Koso have been tested by us and we can say they will keep your hands warm and give you the grip you need in off road conditions, thanks to the full diamond grip design.

• Clamp-on grips do not need adhesive
• External temperature controller with 5 heat levels
• For use with twist throttle; includes interchangeable throttle cams
• Requires 35W and draws 2.5 amps per pair; low voltage shut off

These new heated devices are for the user that does not want to commit to changing their grips but still wants to maintain the comfort of heated grips. The fitment is intended to fit all sorts of handlebar sizes. They can be installed and removed in a matter of seconds and kept in any sport bag when not in use.

Features:

• Universal fit to be clipped on any handlebar sizes
• Rubber material that is resistant to outdoor conditions and high temperatures
• Thin and flexible silicone wires make them easy to install

MAGURA HYMEC – AN EASY TO INSTALL ALTERNATIVE TO A MECHANICAL CLUTCH.

This system replaces the clutch lever and cable – with a small lightweight hydraulic system for improved clutch control. The Hymec ensures an easier operating pressure, a constant pressure point, no more cable adjustment and smooth clutch actuation to ensure the perfect take-off every time. Hymec significantly improves vehicle performance – it allows the user to feel the point where the clutch releases and actuates. This product has been developed over many years and been tested under the toughest conditions possible in the world of motorcycle off-road sport. It has been used by world champion riders who all agree as to the benefits but it is just as useful to the complete novice who stalls at the traffic lights.

• This system replaces the clutch lever and cable – with a small lightweight hydraulic system for improved clutch control
• Up to 20% less clutch pull
• No maintenance and self-adjusting
• Smooth hydraulic feel with clear and consistent pressure point
• Operates on mineral oil which doesn't draw moisture and won't harm paint or finish
• Forged break-away lever blade with reach adjust is ready to mount
• Clutch safety switch included

Replacement folding shift lever, stock length made by IMS.

• Lightweight levers are CNC-machined from aluminum
• Stock length; reach to the lever is adjustable to six positions

Sold Individually

Order up your new levers here! If you keep breaking levers, you might want to think about a set of hand guards to protect them in case of a fall.

• Meets or exceeds OEM specifications
• Made from aircraft A-360 die cast aluminum

• Ergonomically designed
• Medium-density Thermoplastic Rubber (TPR) compound provides excellent feedback and control, without sacrificing durability
• Full diamond pattern for an unparalleled feel in both wet and dry conditions
• Inner diameter optimized to keep grips secure in any conditions
• 115mm overall length; fit 7/8" bars and throttle sleeves

  Competition levers by Moose Racing incorporate a cast aluminum lever with silicone grip inserts and anti-friction bronze bushings

• Levers are approximately 1" shorter than stock
• Sold as a set

  These levers will only fit the DIRT ONLY model! If you have a license plate, DO NOT ORDER!

Factory Yamaha replacement clutch cable.

With the split back, you don't need to remove your grip or throttle tube, just put it on and tighten 'er down. Put the mirror in and hit the road. Clean and simple.

One folding mirror. Includes handlebar mount. Can be used on left or right side.

Sold individually.

This new mirror can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price.

Fits either left or right side and includes handlebar mount.

Sold individually

OEM throttle cable.

Matte black 118mm x 85mm mirrors. Similar to stock size.

• 8mm thread

Sold In Pairs

Simple, clean looking matte black mirrors have an extra long stem. Great visibility for taller riders.

• Diameter: 4-5/16"
• Housing Depth: 1-1/4"
• Stem Length: 7-1/2"
• 8mm universal fit

Sold in Pairs

Handlebar mounts that replace your stock clamps.

These raise your handlebars 1 inch.

Choose 7/8" for standard handlebars or 1-1/8" to allow installation of your choice of oversize/ tapered handlebars.

Order up your new levers here! If you keep breaking levers, you might want to think about a set of hand guards to protect them in case of a fall.

Replace your Bent or Broken Levers.

• Meets or exceeds OEM specifications
• Made from aircraft A-360 die cast aluminum

  TW200 fitment 1987-2000 year models with Drum Front Brake or 2001-2014 year models with Disc Front Brake.

Ease the pressure on your wrist during those long highway drones out to where the fun begins. ProCycle has developed this kit that includes a Vista-Cruise throttle lock, a specially modified alloy throttle tube and an anchor plate that attaches to your throttle housing. Just flip the thumb lever down to apply enough friction to hold the throttle in place. Use the supplied longer screw to attach the anchor plate to your lower throttle housing bolt hole. Also included is a tension adjustment tool that you can keep on your key ring. Keep the applied tension lightly adjusted so it's easy to roll the throttle off.

Fits bikes with dual cable throttle housings.

A set of replacement brake and clutch levers. Standard length.

Please be sure and order the correct levers for your model year KLR.

Note: Gen 1 levers are black
Gen 2 levers are Silver

The Magura Hymec Hydraulic Clutch system. Simply remove the stock perch, lever and cable and bolt this in its place. This system replaces the stock cable with a small lightweight hydraulic system for improved clutch control, easier operating pressure, a constant pressure point and smoother actuation. Developed over many years and tested under the toughest conditions possible in the off-road motorcycle world.

You will have to bypass your clutch safety switch to use this unit.

Never hurts to have a bit of the Margura specific Blood Red hydraulic fluid as well.

A quality replacement speedometer cable.

A quality set of replacement throttle cables from Motion Pro.

ProTaper's ADV handlebars give you a bar taller than most with extra space on the control portion of the bar. These bars provide an additional 20mm of space next to where your levers and throttle are located for your GPS, phone cradle, auxiliary switches, etc . They come in Adventure (which is taller than stock) and Adventure High (which is even taller).

These  are oversize bars, which means they are are 1 1/8", not the smaller 7/8" diameter. Therefore some bikes will require a adapter and there are several available to select from.

Using the same manufacturing techniques and materials as ProTaper’s industry-changing 1⅛" motocross handlebar, the EVO Adventure is specifically designed to provide adventure/touring riders with the increased comfort and control they need. With over 8" of straight section in the control areas, mounting vital components is made easier than ever. With its premium 7000 series aluminum alloy construction and computer-profiled four millimeter-thick wall design, the EVO Adventure Handlebar is up to 25% lighter and 45% stronger than competing handlebars.

• 1⅛" tubing at the clamping area
• Exclusive 4 mm-thick 7000 series aluminum alloy for superior tensile and yield strengths
• Optimum balance between fatigue life, impact strength, and impact-absorbing flex
• High-tech shot peened, stress-relieved, and anodized finish for unmatched durability
• Independent lab tests show that the EVO Handlebar leads the market in fatigue life
• Epoxy inner coating resists corrosion
• Chemically applied cut lines and alignment grid are scratch- and peel-resistant
• Plastic bar end plugs keep the elements out and provide a stronger base for grip ends
• Weighs only 1.55-1.7 lbs. (720-780 grams), depending on bend

Folding tip, forged aluminum shift lever from BBR Motorsports. Stronger and lighter than the stock shift lever.

• Strong forged aluminum construction
• Steel knurled folding tip (chrome plated)
• Anodized titanium finish
• 1/2" longer than stock

Folding tip, forged aluminum shift lever from BBR Motorsports. Stronger and lighter than the stock shift lever.

• Bolts directly to the shift shaft, eliminating the need for the stock linkage which can get sticky and is prone to collecting mud
• Strong forged aluminum construction
• Steel knurled folding tip (chrome plated)
• Anodized titanium finish
• 1" longer than stock

Folding tip, forged aluminum shift lever from BBR Motorsports. Stronger and lighter than the stock shift lever.

• Bolts directly to the shift shaft, eliminating the need for the stock linkage which can get sticky and is prone to collecting mud
• Strong forged aluminum construction
• Steel knurled folding tip (chrome plated)
• Anodized titanium finish
• 1" longer than stock

• Bolts directly to the shift shaft, eliminating the need for the stock linkage which can get sticky and is prone to collecting mud
• Hardened splines won’t slip or rotate
• Strong and grippy tip cover
• Folding tips prevent snagging on brush or rocks
• Steel levers withstand impacts and bends without breaking

Attach this over your brake lever and hand grip, squeeze the brake lever, pull the locking bar in and lock the black portion down. This creates a locked front brake, making parking safe and secure with about 5 seconds of effort.

To unlock the BrakeFix, you just lift the back of the black hooking portion to release it. This takes about 2 seconds. Perfect for use with Snapjack type stands or just parking on an incline.

Bar end mounted mirrors move the mirrors out past your elbows so you can actually see what is behind you. They can mount with or without hand guards.

Sold in Pairs

This new mirror screws into your stock mirror mount but can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price. Fits either left or right side.

Sold individually. If a set is needed, order two.

  All Yamaha's will need a mirror adapter if you have the stock perch.

Genuine Yamaha replacement throttle cables.

OE style clutch or brake lever.

• Quality Aircraft grade A-360 aluminum for strength & durability
• Designed to exceed OEM specifications, built to resist breakage
• Durable hard coating
• Designed to fit OEM perch

Opens your throttle 15% faster. No more 'double handfuls' to get it wide open. Removable end cap for bikes with hand guards.

Throttle, Clutch or Speedo cables.

Handlebar mounts that replace your stock clamps.

These raise your handlebars 1 inch.

Available in 7/8" for standard handlebars allow installation of your choice of 7/8" off road handlebars.

The Warp 9 shift lever is 7075T6 CNC arm, the Warp 9 logo is laser etched into the finish. 

Includes a black folding aluminum tip and stainless spring and pivot pin for years of rust free use.

1" longer than stock

• Warp 9 Flex Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces
• Adjustable reach allows customization to the rider’s hand size
• Double hinge design allows lever to flex out of the way in most impact situations
• Pushrod or Bearing contact styles for smooth brake modulation
• Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal

• Warp 9 Flex Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces
• Adjustable reach allows customization to the rider’s hand size
• Double hinge design allows lever to flex out of the way in most impact situations
• Pushrod or Bearing contact styles for smooth brake modulation
• Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal

This kit is for those of you looking for a bit more leg and arm room in the DR cockpit. Included are ProCycle Low Foot Pegs and our oversize bars.

• ProCycle Low Pegs will drop your pegs by 1-3/4" and include wider MX style pegs that are much more comfortable when standing.
• These are not only taller bars, but 1-1/8" at the clamp area for additional strength. They taper down to 7/8" on the ends so all the stock controls fit. Black in color.
• 1 1/8" Warp 9 clamps that raise the handlebar 1".
• A new billet aluminum throttle tube is included.

This kit is for those of you looking for a bit more arm room and a better platform for your feet in the TW cockpit. Included are ProCycle Wide Foot Pegs and our oversize bars with 30mm risers.

• ProCycle Wide Pegs are wider MX style pegs that are much more comfortable when standing.
• These are not only taller bars, but 1-1/8" at the clamp area for additional strength. They taper down to 7/8" on the ends so all the stock controls fit. Black in color.
• 30mm Moose risers that raise the handlebar 30mm.

Kit does not include new throttle tube. If you have 2001 or newer TW200 and would like a new billet aluminum throttle tube, please select the addon box to receive one with your order.

This bar kit will raise your hands 5.5" up from the factory riding position. If you are over 6 feet tall, this is the kit for you! It allows for a more natural riding position, no more bent neck and being hunched over the bars. You will be able to ride comfortably and more aggressively by installing this kit.

The ProTaper bars are taller and tapered from 1 1/8" to 7/8" and the braided stainless steel brake line will be a serious improvement to your braking ability. Braking becomes more responsive and firmer while adding a stylish look to your TW200.

Everything you need is in this kit to properly raise your bars:

• ProTaper ADV High handlebar
• PowerMadd 2" bar riser
• Harness extensions
• Longer braided steel brake line
• Longer clutch cable

Here is a complete kit to install oversized tapered 1-1/8" handlebars on your DR650. Warp9 handlebar clamps bolt to your stock triple clamp adding an additional 1" to the height.

Alloy oversize bars offer more durability and eliminate the crossbar which opens up your dash area for more goodies. Black in color.

Comfortable Oversize (or Fat Bar) Handlebars.

• Black in color. 
• Made from 5mm, proprietary, 2000 series T6 aluminum alloy for superior tensile and yield strength.
• Lighter and stronger than regular bars
• No-crossbrace allows flex to reduce shock and rider fatigue
• Oversize 1-1/8" diameter base reduces to 7/8" to allow standard-size controls/grips
• Etched alignment marks for fast and accurate positioning
• Bar pad included
• Works with stock controls and cables.

For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8  adapter (sold separate).

CNC machined from 6061 Aluminum by the crew at Warp 9. This upper triple clamp will help to get the bars out of your lap on the XR650L. It allows for six different bar positions (three mount positions and reversible offset mounts). Uses the stock key switch and works with the handlebar lock. Speedometer and indicators all use stock mounting positions as well.

This clamp comes with 1-1/8" bar mounts that work perfectly with the tapered handlebars included. Then there is a new set of ProGrip 714 Rally Grips.

• 4.75" wide,
• Raises handlebars 2 inches and allows fore/aft position adjustment
• Provides dual pivot points for optimal bar positioning
• One piece design is made from solid aluminum for superior strength
• Available for 7/8" - 7/8" or 7/8" - 1 1/8" bars

Requires 7/8" factory bar clamps on bike

A quality replacement speedometer cable from Motion Pro.

• Black vinyl coil-wound housing
• Meets or exceeds OEM quality
• Inner nylon sleeve for longer life and smooth operation

Direct replacement cables for your T-Dub. OEM or high-quality replacements will keep you on the road or trail. Pay attention to the model year for correct fitment, then select the cable type: Throttle, Clutch or Speedo, they're all here.

The plastic fitting that secures the stock choke cable to the carburetor is delicate and easily broken. A broken fitting can cause hard to solve idling and running problems.

CNC machined from billet aluminum and anodized black or blue. If you want to retain your handlebar mounted choke this may be the solution.

  These no longer fit the new version of the ProCycle Remote Choke Cable. Will not work with the long or short reach choke knobs.

The Trail Mirror is a simple solution for any dirtbike or mountain bike. Gives you hindsight when you need it, but you forget it's there otherwise. 

• Made from super tough glass reinforced Zytel
• Reflector diameter: 2" (50mm)
• Bar space: 0.75" (19mm), Height 1.25" (32mm)
• Convex lens for wider field of view

Zip ties directly to the bar- no hardware required.

Sold individually

This adapter will give you more mirror choices.

Yamaha mirrors have reverse threads on the right (throttle) side of the handlebars. This adapter allows you to mount a mirror with standard 10mm threads on the right side of your handlebar. This opens up many options for your mirrors, choose any 10mm mirror for your Yamaha.

• Torque spec: 5 Nm

Order up your new levers here! If you keep breaking levers, you might want to think about a set of hand guards to protect them in case of a fall.

Replace the soft stock levers with sturdy forged aluminum.

Folding tip prevents snagging.

Hardened splines won't slip or rotate.

This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars.

Because these are offset there may be limited clearance between the gas tank and the risers when the bars are fully turned on some models, mainly when mounted to move the bars closer.

The GPR V5 stabilizer is designed to be "tucked" away under the bars and is still easily adjustable without raising the handle bars too high.

• Kit includes damper, bolt on post mount, below the bar mounting system, and complete instructions.
• Only raises bars about 1/2".

• Will only work with Fat Bar style (1 1/8" clamp area) handlebars and stock triple clamp.

These tips are for the Warp 9 Shift Levers only. 

These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours.

You can also order just a new pin hardware kit which comes with new pin and clip.

New from Twin Air, a forged aluminum KLR650 folding shift lever with your choice of Black, Blue, or Green tip. These are 3/4" longer than the stock lever which makes for easier shifting while standing, as well as for those with a larger boot size.

The Go Cruise cruise control mounts over the throttle grip and rests on the brake lever to hold your throttle open, allowing you to stretch and rest your hand on long rides. Installs and removes in seconds with no tools. You can roll off the throttle manually to disengage the Go Cruise.