Search Products

Genuine Honda Factory Service Manual specifically for your CRF250L

The Side Bag Hauler Kit has been designed to work with or without the GCAG Uprising Soft Rack. These straps allow you to use standard dry bags for side luggage. When installed properly you will be able to thrash about offroad and your luggage will stay put! With this setup it is very important to strap your bag in tightly and double check your exhaust clearance.

Bags can be rigged horizontally or vertically.

Hard luggage can increase your risk of injury, especially on offroad terrain. With this system you can reduce your potential of injury and have adaptable, waterproof luggage.

Kit Includes:

• 4 Heavy Duty Cam Buckle Tension Loops
• 4 Four Foot Runner Loops

The Bag Snake kit works great for rear bags and side bags. When rigged with a side bag the second ring on the ring tensioner creates a secondary buckle so you can loosen the top for access and your bag doesn't fall away from the bike.

When rigged for a rear bag the diagonal section of the strap prevents any slippage over the ends of the bag. For this reason, the Bag Snake is great for smaller rear bags.

Kit Includes:

• 1 Heavy Duty Cam Tension Loop
• 1 Heavy Duty Metal Ring Tension Loop
• 1 Six Foot Runner Loop
• 1 Heavy Duty Metal Ring Loop

These flat tie down 'stretch' straps are designed specifically for motorcycles, ATVs and snowmobiles. Carry anything on your motorcycle securely and without scratches with these flat - no hook - tie down straps.

ROK Straps are a two-piece strap with a quick-release buckle in the middle and loops on each end. One end of the strap is a heavy duty nylon, the other has a strong stretchable section. Instead of hooks that can slip or come undone, ROK Straps have a loop sewn in each end. you pass the buckle around your frame, rack or other secure point and then back through the loop in the end making for a very secure mount. With each end secured, connect the buckle in the middle and simply tug the slack end of the strap until your load is firmly held in place.

With 3.5-liters of packable volume, the super-rugged, universal roll-top Possibles Pouch™ provides enough capacity to carry a set of tire irons, spare tube, compressor, tools, and other small offroad essentials. The bag also allows one to add external pockets to Giant Loop’s MoJavi Saddlebag, Coyote Saddlebag, Great Basin Saddlebag, and MotoTrekk Panniers.

The Possibles Pouch gear pocket is 100% waterproof, dustproof, and mudproof. It can be anchored to engine guards, crash bars, tail racks, or any other secure attachment point on virtually any motorcycle make or model. Add Giant Loop’s bolt-on Tail Rack for an instant trail riding solution that gets the weight off your body and onto the bike for improved performance and less fatigue.

• VOLUME: 3.5 liters (214 cubic inches)
• DIMENSIONS: 10.5” L x 5.5” W x 3.0” H (27 cm L x 14 cm W x 8 cm H).
• MATERIALS: Rugged Bomb Shell™ 500D PVC tarpaulin body.

Secure storage of a spare tube, tire irons, or random miscellaneous items is a must for any trail ride or adventure. The OBR ADV Gear Fender Bag is constructed from a heavy duty industrial grade ballistic fabric that secures tightly to any fender via oversized heavy duty gutter hooks. The OBR ADV Gear Fender Bag also utilizes an optional double button snap system that when used eliminates any potential for shifting of the fender bag when riding off road or over rough terrain.

Features

• Heavy Duty industrial grade material construction with high strength UV resistant nylon webbing
• Heavy duty dust resistant #10 coil zipper with cover flap 
• Secure attachment with oversized heavy duty gutter hooks
• Optional secondary button snap retainment system
• Sized to fit most HD 18” or 21” tubes

Features:

• Rear rack comes with grab bars, designed for specific models
• Flat surface with many fitting holes for cargo box and its box base installation
• Comes with loading hooks for secure luggage holding
• Can be used as grab bars for passenger
• Can be used with GIVI universal box bases
• Maximum loading capacity is 5 kg / 11 LB

• Smartly designed to accommodate, but not limited to: 1 gal. - 1.75 gal. Rotopax fuel/water packs, Wolfman Luggage - Wolf Tail bag (M303), and Givi Monokey top cases (separate mounting kit required)
• Large 14.5"(Width) X 13"(Length) luggage platform
• CNC laser cut from 1/4" 5052 Aluminum - weighing only 2lbs. 10oz.
• Each rack is sand-blasted and sprayed with a premium DuPont semi-gloss mini-tex powder-coat finish
• Stainless hardware kit and installation instructions included
• All materials and craftsmanship are sourced 100% in the USA
• Carrying capacity is 20lbs.

PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash. 

Sold as a pair.  Easy to Install

• Complete with all necessary mounting hardware
• Fabricated with 1/2 inch steel tubing, MIG welded
• Finished with a semi gloss black industrial grade powder coat
• Comes with left and right side racks, each side weighs 2 lbs
• The TW200 side racks are intended to work hand in hand with our ENDURO Series rear rack.

Nomadic Rack for the TW200. CNC laser cut from 3/16" 5052 aluminum with a large 12 x 10-7/8 mounting surface area. Sand blasted and then powder coated black to give it a shot peened look. This rack is an easy installation with a 4 point mounting system with no modifications required. There are multiple strap slots for securing gear bags and cargo. Doubles as a grab handle or tow bar. Is compatible with RotoPax mount. All hardware and instructions included.

You may purchase just the rack or you can order the Rack with the RotoPax Mount. If you really want it all, you can order the Rack, Mount and a Fuel or Water Container.

The B & B Eng. DRZ400 Bash Plate is made from 4mm thick 5083 aluminium plate. Strong and great looking, this is the top of the line protection plate for the DRZ. Supplied with all the necessary stainless steel clamps and bolts required. Available in polished or with the heavy-duty black polymer coating. Like all he other B&B Bash Plates, these plates have foam or rubber where required to keep things a bit more quiet. This plate fits the E, S, SM & kick start models.

• Next generation skid plate made with high strength plastic
• Designed to protect the shock absorber linkage from impacts, mud and sand. It allows you to slide easily on natural obstacles ensuring a smooth ride. 
• Impact resistant material effectively protects against stones, earth and mud
• Flexible and lightweight plastic reduces vibration and surface damage to chassis and engine
• The air intakes are designed to give more lightness, aeration and facilitate the washing operations under the engine, reducing the entrance of gravel, earth and mud
• Using the original fasteners of the bike the assembly/disassembly is intuitive to facilitate the normal maintenance and washing of the engine
• Extended protection areas on the side housings, on the water pump and in the chassis areas

Features:

• Provides protection for vulnerable engine components
• Safeguards the exhaust headers, oil filter & oil pan
• For protection from collisions, stones & debris
• Sturdy aluminum construction (4mm sides, 2.5mm base)
• Powder coated black sides with laser cut ventilation holes
• Designed & engineered in Germany

• Protect vital engine parts and cases from rocks and debris
• Clear anodized for corrosion protection and good looks
• Skid plates made from 3/16" 5052 H-32 aluminum
• Smooth underside won't snag when crossing logs
• Oil drain hole
• Heat-treated chromoly steel clamps keep plates mounted securely
• All mounting hardware included

• Protect vital engine parts and cases from rocks and debris
• Clear anodized for corrosion protection and good looks
• Skid plates made from 3/16" 5052 H-32 aluminum
• Smooth underside won't snag when crossing logs
• Oil drain hole on all required models
• Heat-treated chromoly steel clamps keep plates mounted securely
• All mounting hardware included

The 2023-2024 Honda XR150L skid plate protects your bike no matter the terrain. The XR150L skid plates are made from high quality aluminum and offer full coverage. It comes with unique, proprietary hardware that requires no drilling and tapping into your dirt bike. Comes standard with a clear anodize for extra protection. Buy your skid from the industry's longest-running skid plate manufacturer. Ensure your Honda stays safeguarded in style—made durable in the USA.

• Skid plate fits 2023 and up XR150L models
• High quality hardware included - custom made to never fail
• No drill and tapping required
• Extremely easy and fast to install
• Made in USA

Features:

• Additional protection against rocks and contact with the ground for the engine: the high-quality, aluminium alloy engine guard shows what it's capable of off the street, but provides extra safety and an individualized look on the streets, too. State-of-the-art production gives these bike-specific protectors a secure fit. The installation on frame mounting points lends additional stability and allows for easy installation.
• Underbody protection against stone chips and collisions
• Offers more protection through secure and stable attachment points
• Reliable and easy installation on original attachment points, modifications to the motorcycle are not required
• Bike-specific development for perfect fit
• Mounting material included in delivery
• Durable design made of high quality aluminum alloy

bash plate is made from 4mm aluminium 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.

All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

Crash bars by SW-MOTECH provide the necessary extra safety for tank, fairing and components. Designed specifically for these types of bikes, these accessories fit seamlessly with the lines of the vehicle and offer optimal cornering clearance. Bike-specific mounting systems enable reliable, easy installation onto original attachment points.

• Constructed of robust steel with a 27 mm pipe diameter.
• Weather- and corrosion-resistant powder coating in black
• Reliable protection for important components
• Highly stable construction appropriate for the peg length of the motorcycle
• Model-specific development guarantees precise fit and reliable frame linkage
• Optimized lean angle guaranteed
• Simple mounting by screwing on factory-made mounting points on the frame

Adventure bike heaven is off-road headed down a dirt road or a trail. If that is your dream, then as you know, you are going to fall. Sometime, someplace, it will happen, so be prepared! Save your bike before it happens.

SW-Motech makes some of the finest protection equipment available. 

Please Note that these Crash Bars are also compatible with the SW-Motech Skid Plate and the SW-Motech Centerstand.

Made to match the Honda XL750 Transalp, these crash bars are equipped with a weather- and corrosion-resistant powder coating in black. 

Crash bars by SW-MOTECH provide the necessary extra safety for tank, fairing and components. Designed specifically for these types of bikes, these accessories fit seamlessly with the lines of the vehicle and offer optimal cornering clearance. Bike-specific mounting systems enable reliable, easy installation onto original attachment points.

• Construction made of sturdy steel
• Weather- and corrosion-resistant powder coating in black
• Reliable protection for important components
• Highly stable construction appropriate for the peg length of the motorcycle
• Model-specific development guarantees precise fit and reliable frame linkage
• Optimized lean angle guaranteed
• Simple mounting by screwing on factory-made mounting points on the frame

The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike.

Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.

Available in 2 colors

The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike. Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.

Features:

• Protects the frame in the maximum friction area
• Use of rubber to increase grip and therefore control of the motorcycle
• Easy assembly and dismantling with expander and plastic bands

Available in 2 colors

Mount Barkbusters standard aluminum bar handguards to 1-1/8" motorcycle handlebars with the Barkbusters Tapered handlebar saddle clamp set.

What's in the box:

• 4 peice saddle clamp set
• 2 complete saddles

These are all you need to mount your current Barkbusters Handguards when you upgrade to a tapered oversized 1 1/8" handlebar.

To fit tapered 28.5mm (1 1/8") handlebar.

• Barkbusters strongest handguard EVER!
• Designed for Enduro and Trail bikes.
• Two mounting points secure the full wrap around aluminum design.
• Compact curved profile to protect hands and levers during intense trail and tight bush riding.
• Heat treated aluminum backbone for maximum strength.
• Replaceable, high impact resistant EGO plastic guards included.
• Large range of colors matched to popular motorcycle brands.
• Deflectors available for increased protection (sold separate).
• Easy installation.
• Note: Not ideal for bikes with long clutch and brake levers.

NOTE: will not fit Renthal Twin Wall or Barkbusters VSBar.

SW-MOTECH has specially built this centerstand for the Honda CB500X.

The indestructible, yet lightweight steel tube construction offers the best angle and ground clearance, makes it easy to jack up and provides stability - whether it's during maintenance or on the road. In most cases, you will no longer need to buy an additional swing arm stand. During long downtimes in the winter months, the centerstand helps take the load off your tires.

• High quality materials and workmanship
• Stands securely when traveling with lots of luggage and during maintenance
• Bike-specific design for easy mounting and high cornering clearance
• Easy to lift up the motorcycle
• Outrigger for optimal leverage
• Best corrosion resistance due to sand blasting and powder coating of the surface
• Made of robust steel

Made from 1/8" thick stainless steel with dual folded edges for additional strength, these brackets will relocate your passenger pegs down 4" and move them back 1.5". This will give your passenger additional legroom making two-up riding much more comfortable.

All hardware is included for a quick and easy installation.

• Tech-X footpegs provide outstanding performance and control by minimizing vibrations and adapting perfectly to the rider's foot movements
• Innovative rubber bearing between the tread surface and the joint
• Basic vibrations are absorbed and shocks on uneven terrain are mitigated
• Notches dynamically adapt to the corresponding weight shift, by being able to move forwards or backwards - accompanied by an intelligent damping system
• Increased safety and driving experience
• Unique serrated structure ensures reliable slip protection and allows unrestricted concentration on the road
• Parts are pre-assembled, making assembly easy
• Includes specific catch joint

• Each footpeg is cast, heat treated, and hardened from 17-4 stainless steel, given a solution annealing treatment, and age hardened for superior strength
• Width (57 mm) and length (90 mm); slightly convex platform for better boot positioning and grip when leaning forward or back
• Dual plane teeth provides traction without the "stuck" feeling
• Made in the U.S.A.

• Each footpeg is cast, heat treated, and hardened from 17-4 stainless steel, given a solution annealing treatment, and age hardened for superior strength
• Width (57 mm) and length (90 mm); slightly convex platform for better boot positioning and grip when leaning forward or back
• Dual plane teeth provides traction without the "stuck" feeling
• Made in the U.S.A.

• Tech-X footpegs provide outstanding performance and control by minimizing vibrations and adapting perfectly to the rider's foot movements
• Innovative rubber bearing between the tread surface and the joint
• Basic vibrations are absorbed and shocks on uneven terrain are mitigated
• Notches dynamically adapt to the corresponding weight shift, by being able to move forwards or backwards - accompanied by an intelligent damping system
• Increased safety and driving experience
• Unique serrated structure ensures reliable slip protection and allows unrestricted concentration on the road
• Parts are pre-assembled, making assembly easy
• Includes specific catch joint

• Light enduro footpeg with enhanced grip
• Mounted with popular RGK2 peg joints
• Tread on footpegs offer a secure hold even with heavy boots
• Includes two footpegs and two bike specific turning joints
• Notches dynamically adapt to the weight shift by being able to move forwards or backwards with an intelligent dampening system
• Unique serrated structure ensures reliable slip protection and allows unrestricted concentration on the road
• Innovative rubber bearing between the tread and the joint means basic vibrations are absorbed and shocks on uneven terrain are mitigated
• Dynamic adaptation to foot movements
• Enhanced safety and riding enjoyment

• Tech-X footpegs provide outstanding performance and control by minimizing vibrations and adapting perfectly to the rider's foot movements
• Innovative rubber bearing between the tread surface and the joint
• Basic vibrations are absorbed and shocks on uneven terrain are mitigated
• Notches dynamically adapt to the corresponding weight shift, by being able to move forwards or backwards - accompanied by an intelligent damping system
• Increased safety and driving experience
• Unique serrated structure ensures reliable slip protection and allows unrestricted concentration on the road
• Parts are pre-assembled, making assembly easy
• Includes specific catch joint

Low peg mounts from JNS Engineering. You can use your stock pegs or aftermarket pegs with these T7 mounts.

These offer a 24mm drop & 24mm rearward offset.

Note: Not compatible with any center stand.

Double the size of your side stand footprint and half the chances of your KLR tipping over when parked on soft terrain. This laser cut, TIG welded 0.190" thick slice of aluminum bolts to your machine with just the addition of a hole in the stock side stand pad. Just takes minutes to mount.

Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.

This set of high quality replacement steering stem bearings includes:

• Upper and lower tapered bearings
• Upper and lower bearing races
• Upper and lower seals

This is a high-quality seat cover offered by Moose for the DR650. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam. Strong marine-grade vinyl that's made to last. UV protected from sunlight for extended use and has double stitching for extra strength.

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

This is a high-quality seat cover done by Moose for the TTR. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam. Strong marine-grade vinyl that's made to last. UV protected from sunlight for extended use and has double stitching for extra strength.

Seat Concepts seats are constructed using a foam material that is a higher quality than OEM seat foam. Their proprietary formula is a plush ride, while still offering the necessary amount of support. Their unique comfort and shape maintains a similar contour to stock seat at the front, so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!

The Complete Seats come assembled to a high quality with an aftermarket pan and is ready to ride.

"Will not fit standard L model"

• High sound level 105-118 db
• 80mm diameter and only 7.5 oz
• Wire extension included
• Universal for street and off road use

The Trail Tech Vapor Speedometer/Tachometer units are custom designed for an exact fit. They feature a bright white backlit LCD display, waterproof connections, and all parts needed for a complete installation. These units accept AC and DC power input, and automatically switch to internal power if external power is removed. Power connectors are included. Permanent solid-state memory guarantees that data is never lost, even without power. Units are available in black.

Trail Tech provides a one year warranty and unlimited free phone and email support.

Unit functions:

• Speedometer
  • Current Speed
  • Maximum Speed
  • Selectable MPH/KMH Display
• Tachometer
  • Real-Time RPM Bar Graph
  • Numeric RPM Readout
  • Dual Programmable Shift Lights
  • Up to 20,000 RPM
• Temperature
  • Ambient Temperature
  • Engine Temperature (liquid cooled only, optional air cooled sensors available)
  • Dual Programmable Temp Lights 
• Distance
  • Adjustable Distance
  • Permanent Odometer
  • Selectable Mile/Kilometer Display
• Clock
  • Hour Meter, Stop Watch, Ride Time
  • Accumulated Ride Time
  • Permanent Hour Meter

These are the first batteries with built-in jump starting. They intelligently monitor their status, and just before going completely dead, puts itself to sleep with just enough energy to get your vehicle started again. Simply press the RE-START button located on the battery, start your bike and ride away.

These are an extremely lightweight (2.5 lbs.) high-powered Lithium-Ion replacement battery for motorcycles. These batteries offer the first Battery Management System (BMS) found on a powersport battery and includes low-voltage cut-off, over discharge, over-charge, and thermal protections with real time lithium-ion cell balancing. Use of a lithium specific charger to maintain the life of the battery is highly recommended.

Product Size is 8.4"L x 5"W x 2.2"H. If you need spacers, select the optional Foam Kit to pad the battery in the battery box.

This heavy duty DRZ400 chain guard is made of laser cut 1/8” aluminum and finished in textured black powder coating.  The formed flange helps keep chain grime off the rear tire.  

Mounting hardware included. 

*Rear fender with various superficial scratches on the top of the fender. Sold as is. Includes all pieces for complete rear fender kit.

ProCycle Plastics (formerly DSA) Rear Fenders include LED tail/brake light and license plate holder. Vacuum molded, these parts are a design improvement over stock.

*Black front fender with various superficial scratches on the top of the fender. Sold as is.

Front fender from DSA Concepts Plastics is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does. Vacuum molded, these are a design improvement over stock. These are fully compatible in any combination with the original factory plastic.

All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.

Made by Nissin, an OEM supplier in Japan

Premium quality EBC Rear brake shoes.

• EBC brake shoes are radius ground, and edge trimmed
• Lead out chamfers at lining ends

We've been asking for a bigger tank for years and it's finally happened. This is the big brother to the very popular 5.3 gallon Acerbis tank with some modifications to add another gallon and a half of capacity. It's the same width between the knees but extends wider and further forward in front of the knee pockets. This high capacity fuel tank incorporates modern lines and high quality construction that can't be beat. Includes gas cap, petcock and all mounting hardware.

  Installation of the Acerbis tank requires relocation of the front turn signals, otherwise the stock signals will contact the tank at full lock. Our Turn Signal Relocation Brackets move the front turn signals up and forward to clear the bigger tank.

More range at a great price. Choose  the 2.7 gallon tank for the KLX250S in Black, Green, Natural or White.

  This tank will NOT fit the 2009-2015 models.

All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.

The Optimate Cable O-20 is a SAE weatherproof bulkhead/panel mount power source. Main body fits a 1" dia. hole. Overall length of the unit is 12" from top of bulkhead to end of connector. Both connectors are industry standard 2-pin SAE connectors. We also offer an optional stainless steel bracket that you can bolt on wherever you like. This makes a clean installation and you won't have a charging cable hanging loose.

Cable max. rating is 10 Amps. Includes an in-line rubber seal at the connector end and a protective cover at the bulkhead for when you don't have something plugged in. Unit has a 3-year limited warranty.

Don't have an SAE plug attached to your battery? Choose the add on below.

Plug-In connector kit for your CRF. This kit fits Rally and Non-Rally Versions of the Motorcycle. Wires and terminals will come pre-attached with subharness.  

Plugs into the Aux Power connector. 
Harness length is 32" (2.66ft)

Our casual t-shirt with a classic ProCycle Logo on the front and a topo map of our favorite local riding spot on the back. High quality soft t-shirt perfect for everyday wear.

T-Shirt Specs:

• Retail fit
• Tear-away label
• Side seamed
• Shoulder taping
• Black Heather: 4.2-ounce, 90/10 Airlume combed and ring spun cotton/poly, 32 singles
• Heather Dust: 52/48 Airlume combed and ring spun cotton/poly

The 244 Series Dual Sport street and trail tires were designed to be equally at home on dirt or pavement. Great value.

• DOT approved, tube type
• 4-ply rating
• All sizes designed for front or rear fitment

The Shinko 244 is a very popular tube-type upgrade for the front tire on the TW200 or the VanVan. DOT approval coupled with excellent performance both on and off-road make this tire a winner!

The 244 Series dual purpose street and trail tire is designed to be equally at home on dirt or pavement.

• Adventure Trail
• Dual purpose street and trail design
• Designed to be equally at home on dirt and pavement
• DOT approved

Available in 5.10-18 (69P load / speed rating) and 4.60-18 (69S load / speed rating).

From Barnett, the number one name in motorcycle clutches since 1948, we now offer a complete high performance clutch set. This includes Kevlar friction plates, steel drive plates and stronger springs.

The Rekluse EXP employs the same EXP assembly as their premier product; the difference is that it fits into your stock clutch assembly, saving you money! Now you can enjoy the benefits of Rekluse auto-clutch technology on your KLR.

An auto-clutch automatically feeds out the engagement of the clutch using centrifugal force. This allows you to start and stop without touching the clutch lever. The automatic feed is fully adjustable to suit the rider's needs while retaining full manual override with the clutch lever. This automatic feed delivers easier on/off throttle transitions, improved traction, better control, and more confidence.

Complete set of friction plates, HD springs and steel separator plates prevent premature driven plate wear, oil muddying and loss of stack height. Built with swaged aluminum carriers that spread the load on the clutch basket and prevent clutch basket "dogging". Anti-swell, alloy impregnated heavy-duty facings for smooth clutch action. Allows modulation, unlike paper clutches which tend to snatch. Don't forget to add a fresh gasket.

DRC is one of the leading manufacturers of silicone hose kits for motorcycles.

• Durable silicone radiator hose for dirt bikes
• Available for MX, ED racers and street dirt bikes
• Smooth inner diameter allows for increased coolant flow
• Printed white DRC logo. Available in red or blue colors

Made from laser cut, medical grade, 304 stainless steel micronic filter cloth. This filter provides 200% more filter area than most other filters. Most high quality filters will pass particles in the 90 to 95 micron range, and some tested, as much as 300 microns. Sand is about 125 microns and a white blood cell approximately 25 microns. Scott's stainless filter catches items down to 35 microns "absolute". The pleat seam is welded, not glued like paper filters, increasing temperature resistance to 600 degrees F.

Includes forged JE 89mm piston 10.5:1 piston, Rings, Clips, Pin, big bore sleeve and top end gasket set. You will have to have the big bore sleeve installed in your cylinder and bored to fit the larger piston.

Generator cover gasket to seal up the cover once you have your new Doohickey in place. New OEM gasket. What else can we say? If in doubt, put in a new one.

A high quality top end gasket set for the XR650L

Iridium spark plugs are made with premium quality materials.

Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.

• The ultimate in the evolution of spark plug technology and performance from an industry leader
• The iridium electrode is 25% smaller than a platinum electrode, and it's just 1/4 the size of a conventional nickel electrode
• Ultra-small diameter center electrode reduces voltage requirement and extends ignition system life
• Metal shell plating has enhanced anti corrosion qualities

Sold individually, unless otherwise stated.

The current ProCycle logo on front, with the design on the back showing our favorite 'Pavement Ends' sign with the DR rider continuing up the road on the pegs, ready for an adventure!

High quality soft blend t-shirt perfect for everyday wear (90/10 Airlume combed and ring spun cotton/poly).

A super compact shovel with several bonus features!

• Lifetime Warranty
• Compact and Portable Design
• Integrated Survival Features
• Durable and Versatile Cosntruction
• Hidden Tools Threaded in the Handles

This gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh set now avoid having an exhaust leak when you install your new exhaust. This is for a set of two gaskets.

X3 EVO represents the off-road evolution: LeoVince has combined all its experience in the off-road world with cutting-edge materials and Italian design, enhancing freedom in its purest form.

The X3 EVO body is made of AISI 304 stainless steel with TIG welds handcrafted by specialized operators, to guarantee long-lasting performance. X3 EVO will allow you to face the most extreme environments and conditions because it does not fear water or mud, nor wear over time.

The LV logo is their tribute to a motorcycle culture that we have loved for 70 years and is laser etched on the body of the exhaust: it is as endless as their passion.

They manufacture the end cap in 100% real carbon, with their special 2x2 twill carbon fiber, specifically designed to resist high temperatures and make the X3 EVO even lighter.

The matte clear coating, in addition to enhancing the carbon texture, protects the end cap from wear and UV rays, keeping the X3 EVO always in a perfect shape.

The sound of X3 EVO is already unmistakable at low revs. X3 EVO has a direct interior, specially conceived to channel the exhaust gas in an optimal way, to unleash a deep sound, giving a new voice to your bike.

The X3 EVO's Spark arrester has been tested and approved by the United States Forest Service and is essential for off-road riding in compliance with regulations, with more peace of mind, more respect for the environment and more fun.

Since Kawasaki brought back the popular little KLX250 with updated fuel injection, Yoshimura brought back an updated RS-2 slip-on that now incorporates an o2 sensor that accommodates the new fuel injection technology on the KLX. All of that with added power, torque and that distinct Yoshimura exhaust note.

Entire unit is proudly made in the good old US of A to boot!

• Diamond-shaped sleeve
• Large core and increased muffler packing volume means quieter operation
• Stainless steel cone end-cap
• Stainless steel tail-pipe
• 2.8 lbs. lighter over stock unit.
• Comes with USFS Approved Spark Arrestor

The product that you are purchasing is designed and intended for closed course competition use only and is labeled as such, i.e. Yoshimura "RACE SERIES." Yoshimura RACE SERIES products are neither designed nor intended for use on PUBLIC ROADS or LAND. Such use is prohibited by Federal and State regulations.

Looking for motorcycle road trip ideas? How about the best dirt roads by state? Each of the Adventure Series maps highlight the best dirt roads, taking you off-road through some of the most spectacular scenery in the United States.

• Highlights The Best Dirt Roads  |  Features off-highway specific information such as terrain iconography and riding permit requirements
• Waterproof / Tear Resistant  |  The road can be tough on your gear. Our maps are designed to withstand abuse.
• Packs Easily  |  This map folds to 4.25” x 9”.
• Detailed Information  |  Includes written descriptions, points of interest, terrain icons, and elevation profiles of the best dirt roads.

A complete kit to mount your phone (or other electronic device) to your motorcycle. The universal cradle expands from 2.25" to 3.25" wide and 4.75" to 6.25" tall. The width is adjustable but fixed while the upper portion of the cradle is spring loaded to keep your device secured in the roughest conditions.

Select the mount option that works best for you. The mirror mount is shown in the photo at left and is a flat plate with an 11mm hole on one side and a RAM ball on the other. Simply remove your mirror, place the plate between your mirror and the perch and tighten it down.

The handlebar mount kit allows you to mount to either a 7/8" or 1-1/8" bar. Also includes hardware to mount to the back of a lever perch. See image at bottom middle for kit pieces.

The X-Grip with handlebar mount is best suited for larger phones up to 4.5" wide. The spring loaded X-Grip cradle expands and contracts, allowing for a perfect custom fit. Kit also includes a device tether recommended for outdoor applications.

A game changer in auxiliary lights. High output, compact and lightweight!

The New Cyclops Aurora 2 inch lights rated at 4000 lumens combined. Using an authentic top binned Cree XHP50 emitter these lights pack a punch!

Available with or without the daytime Running light option (DRL) which can also be a front blinker. (you may need an LED flasher to do that)

Like all Cyclops lights we only use the Best Real Cree emitters. R113, R10 TUV and Emark certified IP68 rated.

Includes a full relayed wire harness designed for a Motorcycle. No need to use a switch if running the DRL version, also no need for a switch if using the skene dimmer or want the lights on in high beam and off in low beam. The factory switch will work for these applications. 

Look at these quality features!

• Solid Steel cradle mount. No broken or cracked mounts!
• CNC machined aluminum housings
• Polycarbonate lenses, Break-proof!
• 15 degree beam patterns, a great choice for distance and field of view.
• 19 watts each
• 2000 lumens a piece, 4000 lumens for the set.
• Includes a relayed wire harness
• Input voltage 9-30VDC
• R113, R10 TUV and Emark certified
• IP68 Rated

This heavy duty aluminum bracket is specifically designed for mounting auxiliary LED lights to the front of your XR650L without interfering with your large aftermarket fuel tank.  If your bike needs improved lighting this mount is the best place to start!

– 0.190″ 5052 Aluminum
– Laser cut
– CNC formed
– Powder coated black
– Includes stainless mounting hardware and JNS stickers.

LED auxiliary lights are sold separate.

• Eliminates the need to cut and splice wiring when using aftermarket turn signals or marker lights
• Plug into the OEM turn signal plug and then use bullet style connectors used on aftermarket lights
• To verify proper fitment, compare connector photos to OEM connector
• Sold in pairs

When upgrading your Suzuki DR650 with LED turn signals, it's required to install a diode module to prevent all of the signals from blinking at once regardless of left or right signal activation. Some riders choose to splice and solder their own solution, but we like things plug and play. That means all you have to do is plug in the TST kit and you're done! There's no need to cut or splice your OEM wiring harness or break out the soldering iron and electrical tape.

• Plug and play installation - meaning no cutting, splicing, or soldering
• Eliminates issue of all signals blinking when activating only one side of turn signals
• Enables power to flow in single direction from LED turn signals to the dash indicator
• Does not fix hyperflash (LED turn signals flashing faster than OEM specified rate)
• (1) TST Plug and Play Diode Module
• 1 Year Warranty 

This relay will fix your flash rate problem caused by aftermarket signal lights and/or integrated tail light. If your signal lights flash too fast or do not flash, this part is your solution! Plug and play - easy installation.

Only ONE relay is needed per motorcycle.

Features

• Slows signaling flash rate back to the normal rate when your bike goes into hyperflash state (or your signals stay on constantly)
• Plug and play installation: simply replaces the relay already on your bike
• Fits like OEM

This component works with the following signal configurations:

1. All stock
2. Stock taillight, aftermarket signals
3. Integrated taillight, stock signals
4. Integrated taillight, aftermarket signals.

Lose that ugly stock taillight and license plate bracket and install this tidy one from ProCycle. We designed this unit and have it manufactured here in Oregon. Kit includes a LED taillight / brake light unit as well as compact turn signals. We also include splice connectors and split tubing, everything you need for this installation.

There is also an option to include matching front turn signals with side mount brackets that allow you to replace the clunky front signals with the same style as the rear in this kit.

Modern LED technology with a classic look!

This plug & play kit is built around the all new Holley RetroBright LED headlight which comes in three different colors.  

Choose from Classic White (3,000K), Modern White (5,700K), and Euro Yellow.  The RetroBright also features a replaceable bulb.
 

Low Beam: 25W, 2,000 Lumens
High Beam: 30W, 3,000 Lumens
Color Temperature: 3,000k or 5,700k
DOT Compliant
Beam Pattern: Left Hand Drive (USA)

This guard is designed to protect your TW200 headlight from rocks, branches, and any road/trail debris kicked up by the vehicle in front of you.  It’s a one piece laser cut steel component with a sleek black powder coat finish.  Mounting hardware is included. 

Note: installation requires drilling two 1/4” holes in your plastic headlight fairing.

DRZ400 E/S

A pair of Race Tech fork springs to dial in your front suspension to suit your weight.

Fits all DRZ400 models with conventional forks (not for SM)

Recommended spring rates:

Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.

Both kits include all bushings, snap rings, and washers.

Gen 2 kit also includes the necessary O-rings.

Gen 1 kits are OEM bushings, snap rings and washers.

Order up your new levers here! If you keep breaking levers, you might want to think about a set of hand guards to protect them in case of a fall.  

These are genuine factory Yamaha replacements.

Direct replacement cables for your T-Dub. OEM or high-quality replacements will keep you on the road or trail. Pay attention to the model year for correct fitment, then select the cable type: Throttle, Clutch or Speedo, they're all here.

Quality replacement clutch cable.

• Nylon-lined housings and precise OEM component dimensions

Genuine Yamaha OEM Replacement airfilter.  Designed to increase horsepower and acceleration while providing excellent filtration.

Twin Air's high quality materials and superior construction deliver unbeatable performance and protection. The hands-down choice of more World and National Champions than all other filters combined.

Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles without restricting airflow.

Comes with everything you need to freshen up your carburetor.

OEM Suzuki headlight cowling.

Formerly DSA, now ProCycle brand, is a plastics kit in three colors - Black, White, and Blue, as well as Blue fenders with White side panels and Black fenders with White side panels. (headlight cowl not included).

Vacuum molded, these parts are a design improvement over the stock pieces. The side panels have a crisper, more angular look than the stock parts while the front fender is shaped like the DRZ400SM OEM front fender. Big enough to be functional without wind-steering the bike like the stock fender does.

Kits include front and rear fenders, a new LED tail/brake light and license plate holder, and both side panels.

Add a fresh new side panel hardware kit and an adhesive heat shield for a fresh off the showroom floor look.

Add a stock Suzuki headlight cowl if you are doing a complete color change to your DR (must select plastic kit with head light cowl option)

Transform your ride. MadStad's patented mounting system allows riders to adjust the height and angle of their motorcycle windshield resulting in much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide. Better still, this dual-sport version pivots the shield down and forward to get it out of your way for off-road riding!

What's included in the kit:
Their complete bolt-on system is custom-made for your bike and includes everything needed to mount and position the shield. Your bike will not require any modification.

• A set of MadStad adjustable dual-sport brackets
• 3/16" (4.5 mm) thick cast acrylic windshield.

The MadStad brackets bolt to the top of your fork clamps and are completely free of the handlebars. You can adjust the shield for the optimum height, angle and airflow for comfortable street and highway riding. When going off-road you can leave your comfort adjustment as-is and pivot the entire system down and forward in front of the headlight so you can get it out of your face completely. When it comes time to hit the pavement again, simply pivot it back up and you are back in street riding comfort mode.

This is the brace needed to stabilize the big front fender on the XR650L. This simple bolt-on brace reduces wind buffeting at highway speeds. It also helps carry the weight of a fender mounted tool bag.

Made from laser cut 5052 aluminum, then CNC formed and beautified with a shiny black powder coat. Easily mounts in a few minutes using the included hardware.

This is a genuine Suzuki part. We recommend installing a countershaft seal retainer to prevent the countershaft seal from popping out while riding.

Slime Tube Sealant is formulated and tested for use in all tube tires. Once installed, Slime remains liquid and will not harden or dry out. Slime is guaranteed for 2 years.

As the Slime treated tube rotates, centrifugal force pushes the sealant to the tread area creating a layer of protection, repairing punctures as they occur and treating existing punctures. Slime is not intended for use in tubes losing pressure from sidewall punctures, bead leaks, damaged rims or faulty valves. Slime for tube type tires is not recommended for use in tubeless tires.

• Prevents and repairs punctures up to 1/8"
• Remains liquid inside the tire, coating the tread area as the tire rotates
• Non-toxic, non-hazardous, non-flammable, non-aerosol and water soluble
• Tubes treated with Slime can be patched with a conventional vulcanized patch using a bit of patience and care

High quality sprockets

• Stock size is 14 tooth
• Add teeth for highway riding
• Subtract teeth for low end gearing

Counter shaft sprocket replacement requires the removal of the left side case cover. A new gasket may be required. This is also a great time to replace that leaking oil seal!

Now you can have minimum output shaft wear, minimum chain drive wear with the FRITZCO DRIVELINE sprocket. The design of their sprockets provide correct chain alignment, allows for full spline contact with the XR650L's output shaft, fit the counter shaft either way, and straight up no hassle installation with the OEM two bolt retainer and fasteners (except 13 tooth that comes with it's own quick change retainer). Their sprockets are machined from alloy steel that is comparable in every way to OEM Honda and the best offered by other manufactures. The sprockets are then given a heat treatment that provides a compatible sprocket for the Honda output shaft and longest wear life possible.

A way to double the sprockets life would be to have a sprocket that fits on the shaft either way so both sides of the teeth can be used. Bear in mind you can't wear one side of the teeth all the way through, then flip the sprocket, and expect double life. You must reverse when a normal wear pattern develops.

16 tooth sprocket is the biggest front sprocket that will run with the standard 110 link chain and 45 tooth rear sprocket on an XR650L
The OEM cover will require modifying to use the 16 tooth sprocket on your XR650L.

Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.

With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way. 
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.

The Swiftkicker is 100% manufactured in the USA from the highest quality components. 
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.

Measured from the center of the pivot to the bottom of the foot.

• Standard length travel range is 13.5"-19.5" (the middle of the travel is approximately the same length as the stock stand)

Ride in warm temperatures a lot? Worried about your motor oil just getting too hot? The Trail Tech Universal Fan Kit mounts up to the backside of the DR's oil cooler to draw cool air across it and keep those oil temps down. An electronic temperature sensor mounts to the fan, no need to cut any fluid lines, and automatically turns the fan on when needed to keep the temperature in the optimum range.

The activation sensor can be set wherever you like to keep the temperature right where you want it. Backlit for easy viewing anytime it also includes a volt meter.

Kit Contents

• 4 inch SPAL fan
• TTV Temp Meter
• Temperature Sensor
• Complete Wire Harness

In order to be prepared for all possible mechanical mishaps along the trail or on any adventure, we are required to carry a certain selection of tools. The OBR ADV Gear Tool Roll will help keep those tools together and stored in an organized fashion easy to be found should one of those mechanical mishaps occur.

Features

• Heavy duty ballistic nylon construction
• Heavy duty #8 coil zipper
• Individual Tool Slots for Tire Irons, Wrenches, Screw Drivers … along with a zippered pouch providing secure storage for those smaller items
• Detachable 10”x10” slip pocket cover flap that also doubles as a hub pad keeping your hub out of the dirt when changing a flat
• Open dimensions 11” x 17”