T7 Ténéré 700

Flats never occur next to a green grassy field with daisy’s … it always happens way out in the bush and in the dirt and weeds. Change your flat on a clean surface protecting your hubs and bearings from picking up unnecessary dirt and debris with the OBR ADV Gear Flat Mat. Our 24” x 24” Flat Mat provides you a clean area to set your wheel onto while also having convenient slip pockets to stash those easy to loose bits and parts that you removed during the flat repair.

Features

• Heavy duty industrial material construction
• Slip pockets to keep those loose parts and tools close by
• Reinforced center panel to set your hub onto
• Folds flat for easy storage within your luggage

In the shop or on a trip, these are the Tire Irons to have.

Sold Each

• Constructed of strong, heat-treated vanadium steel
• Spoon design decreases the chance of tube pinch
• 10" long tire iron with coated rubber handle

Replace your motorcycle’s windscreen with PUIG’s touring windscreen. Manufactured in acrylic of 3-4 mm according to the motorcycle model to guarantee maximum protection from the wind, improving the aerodynamics of the piece and possible debris that may impact you during your ride.

In addition, it comes with a variable visor that will redirect the wind even more while achieving a great sense of comfort on board your machine. This visor is fixed to the touring windscreen by screws, since the screen comes with the holes already made to facilitate assembly.

The windshield has a rounded contour of> = 2mm, complying with the TÜV regulations.

This part is only available in smoked finish.

For assembly, PUIG provides instructions with mounting tips, so you can quickly enjoy the touring windscreen on your motorcycle.

This product has been designed to fit the Yamaha T7 Ténéré

This kit will give you 80mm of adjustment over the stock screen.

In the raised position, the difference in ride comfort is remarkable. Wind noise reduction is very noticeable and airflow underneath your screen reduced the vacuum effect, creating smoother airflow and reducing turbulence.

In the lowered position, the screen sits at the same height as stock.

To adjust the screen, loosen the thumb nuts, slide into position and re-tighten the thumb nuts, no tools required.

Windscreen attaches to your bike's handlebars. Fully adjustable mounting brackets. Includes 7/8' handlebar clamps. 14" tall & 10" wide.

Will not fit 1 1/8" oversize handlebars.

Transform your ride
MadStad's patented mounting system allows riders to adjust the height and angle of their motorcycle windshield resulting in much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide.

What's included in the kit
Our complete drop-in system is custom-made for your bike and includes everything needed to mount and position the shield. Your bike will not require any modification.

• A set of MadStad adjustable brackets
• The acrylic windshield

Installation is super simple. Our bracket system attaches where the stock shield normally goes and our shield then attaches to the brackets. With the shield separated from the front of the bike you can pull lots of air underneath it which is critical for smooth comfortable wind protection. You still have a fairly compact shield but now the wind pressure on your head and face are gone, and you are still looking comfortably over the shield.

All MadStad windshields are made from 3/16" (4.5 mm) thick cast acrylic.

Puig Visor Clip-On

• Suitable for screens with thickness between 3-5mm
• Multi-adjustable visor adaptable to Puig and OEM windscreens
• Visor is mounted by clip-ons and does not need to be drilled to the windscreen
• Visor sizes available include 90x230mm, 100x277mm and 102x325mm

Universal design. Vents in the back improve airflow to motor. Smaller front reduces 'wind steer' and improves high speed stability.

Universal off-road front fender. Must be drilled to fit your mounting bolt pattern.

This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.

Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.

Adhesive heat shield for your new side panel plastics to protect it from the heat of your muffler.

Depending on your application and preferences, more than one heat shield may be useful.

Dimensions: 2"x3'

The One-Piece Comfort seat is 11” wide and designed to improve weight distribution and support when seated while still allowing the rider to move freely when standing. Built to withstand the rigors of adventure riding, the T7 One-Piece Comfort seats are designed with the rider in mind.

Available in multiple cover options and three different heights: low, standard, and tall. Whether you have a 26” or 36” inseam, Seat Concepts has you covered.

 Available as a complete seat only, including seat base. 

Engineered with precision and hand crafted with premium materials including Seat Concepts’ proprietary foam formula, the 8” wide One-Piece Rally Hard Adventure 2.0 seat is designed to provide you with an open cockpit for increased mobility during technical riding and traction ribs to help keep you planted.

Available as a complete seat only including seat base. 

Engineered with precision and hand crafted with premium materials including Seat Concepts’ proprietary foam formula, the 8” wide One-Piece Rally seat is designed to provide you with an open cockpit for increased mobility during technical riding. 

Available as a complete seat only, including seat base. 

Canyon Dual Sport saddle is designed specifically to provide long range comfort for your Tenere 700. We also offer a Bench style saddle that provides more freedom of movement for riders that lean towards off-road riding.

Their high density Comfort Cell foam allows a sleek profile while providing a firm supportive ride that lasts. Rider seating is ergonomically shaped to fit the curve of your body and provide better weight distribution. This also helps to eliminate the centralized pressure felt from the stock seat. In the nose area, they sculpt the saddle narrow to allow for good ground reach. Canyon Dual Sport has a seat height between the Yamaha Rally seat and Yamaha Low seat.

Passenger seating area is designed with a neutralized platform to curb sliding forward in the saddle. Dished shaping provides an excellent contact patch while maintaining a clean look. For the best combination of looks and support, add the Ovalbac backrest shown. This backrest provides a generous, contact patch for excellent support. Angle adjustment is simple and can be performed without removing the saddle or backrest from the bike.

For an added luxurious touch, this saddle is available with the option of electric seat heaters. With the flip of a conveniently located switch built into the left side of the saddle, both the rider and passenger seating platforms will heat up and maintain temperature automatically. Simple to install with just a pigtail wiring to your bike's fusebox. All other components are built into the saddle and come preinstalled.

The design shown above includes Black Carbon-Fiber leather seating with Matte Black vinyl contrasting sides and a tasteful color coordinated Smoke Gray welt.

The default cover choices are black 'carbon fiber' on top and 'asphalt' on the sides, 'no welts', black logo. You can view all of the available materials and colors through the link below. If you would like your seat built with something other than the standard choices please state specifics in the comments during check out.

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

With this seat having so little foam to be able to make it a low, there is a sacrifice in comfort. The T700 comfort low seat provides you with 7/8" of drop compared to the OEM seat for increased reach to the ground.

Height: 7/8" Lower than stock.

Width: 10.5"  - OEM width 7"

Available as a Foam & Cover Kit and an option for an OEM Rear Cover, replacement cover to match the Kit.

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!

Height: OEM

Width: 13"  - OEM width 7"

Details:
The T700 comfort sport-touring seat provides you with an increased level of comfort and support to aid with those long days on the bike.

Note:
Available as a Foam & Cover Kit. Also, available with rear comfort foam & cover kit.

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!

Height: 1.25" Taller than stock.

Width: 10.25"  - OEM width 7"

Details:
The T700 Comfort Tall seat provides you with 1.25" of height compared to the OEM seat for increased reach to the ground.

Note:
Available as a Foam & Cover Kit and an option for an OEM Rear Cover replacement cover to match the Kit.

This is the secret for being able to put in those 500 mile days. Even a good touring seat can feel a bit firm after a couple hundred miles. Sheepskin gives that little bit of 'cush' and provides superior air circulation. Velcro straps allow easy removal when you don't need it. Measures 14" wide by 19" long.

• Air filled AirHawk 12"x18" cushion custom fits your shape and redistributes pressure that causes numbness and discomfort when you ride
• Seat cushion cover is constructed of a breathable, stretchable Nylon/Lycra blend with a non skid Urethane base
• Open mesh side panels allow heat to escape
• Easily inflates by mouth with no pump needed
• Mounting straps and Repair patch kit included

9" by 9" carbon fiber seat warmer that goes between your seat cover and the foam to keep your backside happy on those really cold days. This improved design produces 25% more heat than most other warmers using just 30 watts.

Kit includes the warming unit, with connector, 24" extension cable, rocker-type on/off switch and stub to splice into your wiring along with complete detailed instructions.

CRF450L '19 - '24 CRF450X '19 - '24

This seat is black 'carbon fiber' on top and 'asphalt' on the sides, with red welts, exactly as shown. Slight discrepancies with cover under seat, and slightly off center foam thickness, indicated in pictures. As is, no warranty.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat.

• Simple and quick to mount with plastic insert and two additional screws
• Flexible Heavy-Duty Polypropylene will not effect chassis ability to flex, will not effect handling
• New style developed after extensive research with factory race teams
• New vents keeps engine from overheating
• Offers maximum protection for chassis and engine
• Works great in sand and mud
• Weight 0.75 lb

T700 TENERE Bash plate was designed to withstand the harshest Aussie conditions. Bash plate is made from 5mm structural thick alloy plate and designed for maximum protection with minimum bulk.

Easy to mount and remove. Also includes a replaceable polyethylene linkage guard.

• Fully tig welded
• Comes in polished or black PPA coating.
• All hardware for mounting is included.
• 4 Flush fitting mounts, 2 M8 and 2 M6
• Weighs 3.8kg
• Fits with Genuine Centerstand

Fits EURO 4 only

• Made from high-density polyethylene construction
• 8 mm thick HDPE offers more protection than the standard Pro Skid Plate
• Full linkage protection
• 40% lighter than aluminum and no rattling
• Mounting hardware and installation instructions included

Enjoy maximum protection and durability with an SW-MOTECH skid plate. Fully welded aluminum construction is engineered in Germany to provide proper protection from impacts, abrasions and projectile debris. Multiple ventilation slots on the front, sides and bottom of the skid plate permit maximum air-flow to keep your motor cool. Drilling, cutting, welding or any other permanent modifications are not required.

Features:

• Debris and collision protection for the engine 
• Fully welded 4mm thick aluminum plate / black side made of 2.5mm thick aluminum
• Efficient underbody protection of stone-chipping and collision
• Provides protection for the vulnerable oil pan & lower engine cases
• 100% bolt-on, no drilling, cutting, or any other permanent modifications needed
• Ventilated design maximizes air-flow to prevent overheating
• Silver
• Designed & engineered in Germany

What's in the box:

• SW-MOTECH skid plate engine guard
• Mounting hardware 
• Installation instructions

FUNCTION:

• Highly resistant protection of the engine covers against stone strikes and damage from falls or impacts when handling the bike.
• Impact-absorbing rubber inserts positioned to cushion the contact between part and engine cover
• Perfect shape to perfectly fit your T7.
• Small gap between standard cover and protection
• Rubber inserts allow a more even force distribution
• High-quality hardware
• Rubber inserts are resistant to high temperatures

TECHNOLOGY:

• Highly resistant plastic polymer to protect against falls and impacts
• Over-injected metal part strategically positioned to enhance protection in the event of a crash
• High-quality precision manufacture with over-injected impact-absorbing rubber inserts and over-injected stainless-steel insert

OTHER FEATURES:

• Mounting kit included
• Fast and easy installation and removal
• Engraved metallic part with Polisport logo
• Texturized surface for a premium look
• Minimal design to blend into motorcycle look
• Developed and made in Europe

PACKAGING & PARTS INCLUDED:

• Packed in recycled carton box
• Includes one Clutch and Alternator Cover Protector
• Includes all material needed for an easy installation

Protect the most vulnerable components of your bike with this pair of R&G Engine Case Covers, now available in kit form. Engineered with 4mm polypropylene for superior strength, longevity and sleek aesthetics, these protective guards complement all other R&G crash gear perfectly.

Features:

• Crafted from 4mm polypropylene
• Bolt on installation atop existing engine case cover
• Low profile for maximum ground clearance
• Ultra lightweight with matte black finish
• Meets or exceeds AMA racing specifications
• AMA approved for use in any regulated event

Adventure bike heaven is off-road headed down a dirt road or a trail. If that is your dream, then as you know, you are going to fall. Sometime, someplace, it will happen, so be prepared! Save your bike before it happens.

SW-Motech makes some of the finest protection equipment available. The set-up for the Twin is available in a standard black powder coating or a semi-polished Stainless-Steel tubing. Both sets will protect the vital components of your motorcycle as well as you from damage incurred during a fall, slide or crash. They will preserve the frame, radiator, bodywork and other critical components from touching down with robust tubular steel. The black kit uses 27/21 mm tubing while the Stainless uses straight 22 mm tubing throughout.

Both configurations have a tight fit for great ground clearance and are designed to work seamlessly with other SW-Motech products like their Skid Plate/Engine Guard and SW-Motech Hawk light mounts. Three secure mounting points per side provide the necessary support that make these so strong. There is no drilling, cutting, welding or any other modifications required for mounting but still allows access to the oil filler, tool box and battery. Kit includes all necessary hardware and instructions and an aluminum cover to replace the OEM plastic cover at the lower mounting point on the left side.

Please Note that these Crash Bars are also compatible with the SW-Motech Skid Plate and the SW-Motech Centerstand.

The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike. Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.

Features:

• Protects the frame in the maximum friction area
• Use of rubber to increase grip and therefore control of the motorcycle
• Easy assembly and dismantling with expander and plastic bands

The SW-MOTECH Rear Brake Master Cylinder Guard is designed to fit the Yamaha Tenere 700. This guard protects the rear master cylinder from impact and prevents the foot from contact. A laser-cut and precision bent aluminum strengthening process makes the construction tough and durable and capable of withstanding heavier blows.

Features:

• Prevents contact between boot and foot brake cylinder and provides additional protection
• Lasered and bended from high-strenght aluminum.
• Brushed silver finish
• Easy Installation

• Provides flat surface on both sides of the frame for better bike holdings.
• Made of 2mm thickness 5000 grade aluminum for durability.
• Hairline processing surface finish.
• Comes in a pair, bolt on design, and no modification required for installation.

Don't cut the ball ends off of your levers! These billet spacers move your hand guards outward to allow clearance for the full length of the stock levers. Designed to fit steel or aluminum bars. Includes longer stainless steel mounting bolts.

Developed for the DR650 but may work on other models with long levers. (May require additional adjustment or modification on some models.) 

  Not compatible with Acerbis and Emgo hand guards

Provide protection for your motorcycle’s front brake and clutch levers with Barkbusters aluminum bar lever protection handguards. Designed specifically for the Tenere 700, these guards feature heat treated full wrap aluminum backbones that mount at two points on each side for strength. Prevent costly damage to your motorcycle with Barkbusters aluminum bar lever protection handguards.

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Easy installation
• Compatible with all Barkbusters deflector guards (not included)

Add Plastic Handguards for a complete kit.

Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.

Images show a set of these hand guards installed on a set of CR High Gunmetal Fly Handlebars with large black deflectors. The far right image shows the need to flip the brackets that attach to the bar on the clutch and front brake side. On the front brake side the clamp must go over the front brake line while on the clutch side it goes under the cable.

Note: This kit includes the handguards only. Deflectors sold separate, can be added by selecting color from drop down menu.

For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.) 

• High-impact, composite injection-molded outer guard around an anodized aluminum inner guard
• Includes an indexed steel bar-end insert that mounts solidly and prevents Rally Pro handguards from slipping – even under the most demanding conditions
• Small integral spoiler incorporated into design
• X-Strong universal silver mount kit that fits 7/8” (22mm), Pro Taper 1 1/8"(28mm), Magura and Twin Wall aluminum handlebars included.

Some models with adjustable windscreens may need the windscreen rotated forward, such as the Royal Enfield Himalayan, to avoid contact at full lock. These are not compatible on Honda CB500X's and Honda Africa Twins.

These handguards come with mounts that will work on both standard and and oversize bars. The aluminum wrap-around bar is the biggest on the market with two large plastic shields that are also some of the largest available. The X-Factor hand guards offer great protection from the elements, especially during those colder months when you're trying to stretch out your riding season.

Works with 7/8" or 1-1/8" bars.

X-Factor guards may require you to cut your lever ends down, or use short levers.

Replacement handguards for your Acerbis set up. Tough Polypropylene shields with a larger 6" outer diameter, built for extreme riding conditions.

The X-Factory Handguards from Acerbis feature a steel bar wrapped with an injection molded Nylon composite. A replaceable dual injected polypropylene shield mounts to the bar offering insurmountable protection from roost, debris, and extreme conditions.

A universal mount kit is included that allows for mounting on either 7/8" or 1 1/8" handlebars.

Will not fit XT250 with stock handlebars (oversize bars ok). Recommend Acerbis Rally Pro X-Strong to clear master cylinder.

• Designed to minimize handlebar vibration for Barkbuster Handguards that can’t accomodate OEM handlebar weights.
• Sleek aerodynamic look.
• Forged Steel with powder coat finish.
• Fit in conjunction with most Barkbusters backbones (except EGO).
• Fits externally to the VPS backbone.
• Available in black.
• Sold as a pair

Weight:
360 grams/pair or
180 grams/each

Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Easy installation
• Tough and weather shielding Storm handguards
• Aluminum backbones are compatible with all Barkbusters deflector guards

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right Storm plastic handguard deflectors
• Installation instructions

Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.

NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar

Maximize your wind protection with the Barkbusters largest handguard plastic! For use with single sided Storm mount and all Barkbusters backbone handguards

Keep your hands and controls protected from the wind and impact with Barkbusters VPS lever and wind protection handguards. Heat treated aluminum backbones with two mounting points of these handguards provide the strength needed to prevent a tip-over from ending your motorcycle ride. Impact resistant deflectors, available in multiple colors, provide protection for your hands from the wind and brush. Ride longer, more comfortably with Barkbusters VPS lever and wind protection handguards

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Includes VPS left and right plastic deflectors
• Easy installation

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right VPS plastic deflectors
• VPS deflector fastening hardware
• Left and right adjustable position wind extension deflectors
• Installation instructions

Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.

NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar

Replace the deflectors on your aluminum bar backbones with Barkbusters VPS wind protection replacement handguards.

• VPS Skid Plate (set of 2).
• Fit in conjunction with VPS plastic guards on a Barkbusters backbone.
• Protects the outer edge of the aluminum backbone.
• Adds a stylish finish to the handguard.
• Available in Black only.

Construction of these handguards feature heavy duty aluminum guards with colored plastic deflector shields. They offer great protection from those trees that jump out at you on the trail and the cold wind and rain you encounter on the street. They feature a deep bend on the outer bar end for maximum freedom of hand placement and high quality bar mounts on the inside.

Select your desired color. 

Must add the corresponding size mounts to fit your handlebar.

For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.) 

Please Note: These handguards do not fit the Yamaha T7

You can keep your Cycra handguards even if you upgrade your handlebars to a different width.  

Replacement mounts that keep your Cycra handguards fresh and tight.

CNC-machined from billet aluminum for the best fit and strength.

Please Note: These handguards do not fit the Yamaha T7

Replacement handguards for your Cycra set up. Injection-molded high-impact plastic replacements. Includes all hardware needed for mounting.

Fits Moose and other aluminum hand guards

• Aerodynamic and stylish design
• Protect hands from brush, water and cold wind
• Simple installation
• Sold in pairs

FUZION guard feature the ultimate in hand protection with a unique design and flexible yet durable material. 

The expanded coverage area sweeps back toward your hand significantly increasing coverage making it perfect for cold, muddy or wet conditions. 

The FUZION features a unique two position mount and is constructed of molded light-weight closed-cell AEPE foam, which is crush-proof, water proof and extremely durable. 

The FUZION will work great for road of offroad riding, where wind deflection is important, and or bouncing off trees is a common occurrence. 

Kit includes mounts. Optional replacement mounts available.

Today's newest motorcycles are more likely to have flat-panel instrument displays than conventional mechanical gauges. And, like your cell phone, it's worth the effort to protect the often fragile and scratch-prone screen face with the new R&G Second Skin Dashboard Protection kit. Made from high quality, anti-scratch material, the R&G screen protector kit has been designed to preserve the clarity of your motorcycle's dashboard screen.

Features:

• High-quality protective plastic
• Excellent optics

Includes:

• (2) dashboard protectors
• Mini spray bottle
• Suede polishing cloth
• Wet & dry wipe
• Squeegee & dust-removal strip

Extend your comfortable riding season with Barkbusters BBZ cold weather protection handguards. Designed to fit with or without existing Barkbusters backbones or handlebar weights, these guards offer superb wind protection without limiting access to your grips or controls. Simple to install, they can be mounted or removed within ten minutes without permanent modifications. Ride with less bulky gloves in colder weather with the Barkbusters BBZ cold weather protection handguards.

Features:

• Fits most motorcycle handlebars
• Maximum cold weather protection
• Compatable with or without Barkbusters backbones
• Lined with waterproof membrane
• Windproof
• Full wrap design
• Allows full access of controls
• Does not block view of handlebar thumb controls
• Simple to install and remove

Whats in the box:

• Two BBZ cold weather handguards
• Mounting hardware
• Instructions

The OBR ADV Gear Enduro ¾ Grip Mitt is your answer to cold fingers! Our ¾ open design terminates right at the wrist, but still offers full coverage of the hand while blocking the swirling air flow that freezes finger tips. Their ¾ open design does not cover important controls such as Hi/Lo Beam, Turn Indicator, or Kill Switches making this Grip Mitt perfect for both Off Road, Enduro, ADV, and ATV applications with full wrap hand guards.

Features

• High strength and water resistant 1680d Ballistic Nylon construction 
• Universal easy on/off Velcro snap strap attachment system
• Reflective Front Strip for High Visibility
• ¾ Open design provides full coverage of the hand while not impeding controls
• Works with OEM and Full Shield (Cycra/Trackside) style hand guards (Hand guard system required for attachment)

Droppin’ into the weather? Combine Bushwackers Hand Guards with rigid hand guards/deflectors and heated grips for the ultimate protection against the elements. Ride safer and longer with warm, dry and clean hands and controls. Essential gear for motorcycles, snow bikes and snowmobiles.

• Cold/wet weather comfort
• Brush, mud and trail protection
• Strap on/off in seconds
• Multiple mounting configurations to fit most motorcycle makes/models equipped with rigid hand guards and/or deflectors
• Tough stretch polyurethane strap (can be used separately)
• Custom wind foil shapes
• No stitching or pieces to fail
• When not using Bushwackers Hand Guards, straps have a thousand other uses: Lash water bottles, fuel, gear to tail rack. Hold flashlight in place while working in dark. And many others!
• Made in USA

REQUIRED EQUIPMENT: Motorcycle must be equipped with rigid hand guards or deflectors to support Bushwackers while riding.

Materials: Corona (UV) Treated, Matte Finish, .055 Gauge Polyethylene Plastic
Dimensions (flat): 13.5″ (length from end closest to bar clamp to end closest to bar end) x 16″ (widest part at end of bars) x 6″ (narrowest part nearest center of bar)

It may not surprise you that they are covered with HippoSkin™, their waterproof outer shell, and insulated with a generous layer of HippoFat™, a warm, flexible, closed cell foam insulation—both are designed to keep inclement weather away from your hands.

Sold in pairs.

Hand/brush guards are required for proper fitment and for safety reasons.

Hippo Hands go on and off in seconds and never require tools or hardware.

Extra protection in bad weather to help keep your hands warm and dry. These nearly double the protection from most plastic type deflectors.

The outer shell is made from heavy-duty 500-denier nylon with 1/2" closed cell foam to keep the wind, cold and rain off of your hands.

Ready to go tool kits. Just toss it in your bag and hit the road... or the trail.

A portable device that can jump-start your motorcycle or car. It can also charge your cell phone, GPS unit, laptop or other electronic devices via USB cable.

• XP-1 is 6" x 2 7/8" x1" 14oz.
• XP-3 is 5" x 2 7/8" x 1" 12oz.
• Holds a charge for up to 1 year.

GET JumpStarter Mini, the second-generation, multifunctional jump starter. Now lighter and smaller, it's ready to help you restart any motorcycle or scooter when the battery is low. You can also use the powerful built-in LED flashlight or charge your use it as a power bank to charge your electronic devices. JumpStarter Mini comes together with a hard, water-resistant case perfect for carrying it anywhere and protecting it on your journeys.

• Light and compact multifunctional mini starter
• Allows restart of motorcycles and scooters when they are out of battery
• Can also be used as a Power Bank for electric devices thanks to the USB output port
• USB 5V2.4A output allows connection to tablets, smartphones, MP3 etc.
• Has built-in LED flashlight
• Easy to use; provides special protection against overvoltage and inversion of power supply polarity
• Start current: 200A, peak current: 400A, operating temperature range of -20°C to 60°C
• Includes JumpStarter, Smart Cable, 3-in1 USB cable and user instructions
• Measures 155 mm x 79 mm x 16 mm

• Designed to quickly and precisely remove outer bearing race from the steering head without the use of a hammer and punch
• Puller design ensures bearing is pulled perfectly straight to eliminate possible damage to frame
• Works on all tapered bearing races from 47 mm to 55 mm OD
• Precision machined anodized aluminum cup will not damage seal surface
• Brass bearing washers for easy use and long life
• Hardened steel jaws engage securely on inner bearing lip
• Lifetime limited warranty

Here is a set of 'trail size' tire irons. At 8-1/2 inches long they are small enough to fit in a fender bag with your spare tube.

Motion Pro T-6 Combo Lever has a hex box wrench for your axle nut on one side and a perfectly contoured tire spoon on the other. Manaufactured from lightweight forged T-6 aluminum with a hard anodized finish. These beauties are just under 10 inches long and weigh only 3.5 oz. Available in a 12/13 combo unit and a 22, 24, 27 and 32mm hex ends.

A kit that includes an Axle Wrench combo for your bike with a 19mm for the front, and a 24mm for the rear. Just 7 1/2" long, it is long on leverage, but short enough to fit in even the smallest tool kit.

Also includes a pair of 'trail size' small tire irons.

These Rider's Wrenches by Fredette are combination wrenches that have three wrenches in one! A 2-stroke size spark plug wrench - a front axle and a rear axle wrench. Yep, all three in one unit.

Available in the combinations shown that will fit virtually all current dual-sport machines.

Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.

Thin wall bi-hex sockets designed to access narrow spark plug holes.

Fits 3/8" square drive and hex drive, 14mm, 16mm, 18mm, 21mm.

Our portable 12v compressor is perfect for any tool kit. This unit weighs only 14 oz and measures just 4"x2"x6".

Features a built in LED light and 0-120 psi gauge

• Comes with everything shown

The Mini-Morph is actually a bicycle pump, but it is the best manual compact pump for adventure / dual-sport riding. It has a fold-out foot and handle and a 4 inch hose so you can set it on the ground to pump!

This thing is small enough to stow away in just about any bag and go unnoticed until you need it to fix a flat or add air after a long arduous ride.

It seems that while packing for every adventure … we always end up with a few items that were either neglected to be packed, were last minute gear additions, or just needed to be packed in a readily accessible location…. The OBR Adv Gear Tool Pouch is the perfect solution for these miscellaneous items. Once packed the tool pouch can be slipped into any bag or attached externally using integrated webbing loops that are built into the pouch.

Features

• Heavy duty industrial material construction with high strength UV resistant nylon webbing
• Heavy duty #10 coil zipper that won’t jam up in the dust
• External reflective webbing with Molle loops
• Pouch dimensions 5” x 13”

* Tools not included

Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.

The three forces of suspension, testing procedures, even the black arts of chassis geometry: Thede explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.

The genuine factory shop service and repair manual. This is the reference manual Yamaha dealers use in their service departments. It has all the necessary info to do any maintenance or repairs to your T7.

• Resists extreme environments; won't melt up to 500°F; remains flexible to -60°F
• No adhesive; fuses only to itself
• Forms a water- and air-tight seal
• Tensile strength of 600 psi
• Insulates to 400 Volts/Mil
• Tight insulating tape is 1" W x 10' L and stretches to three times its length

Changing tubes or tires without the right tools can be a real chore. Don't fight your snug beads any longer, use this 27" long tool that opens to 7-3/4" to provide the leverage you need to easily break your tire bead. Constructed from heavy-duty steel with comfortable no-slip grips, this tool makes the job a snap.

No more fighting to keep the bead down while installing or repairing your off-road tires. The Bead Buddy holds the tire bead down in the drop center of the rim during tire changes making changes as easy as possible. Machined from tough 6000 series aluminum the Bead Buddy is light weight and compact enough for any tool pack. The Delrin securing thumb screw insures no scratches to your rims.

The Bead Buddy is NOT recommended for use with Bib Mousse tubes.

• Durable 6061 aluminum with blue anodized finish and laser engraved logo
• Used to push the tire bead down into the drop center of the rim on off-road wheels while using tire tools to change tires
• Hooks over spoke and pushes bead down on opposite side of tire from tire irons
• No more fighting to keep bead down while installing off-road tires

• A tool to keep open up the bead when replacing a tube.
• Works smoothly even with the toughest beads.

• Innovative multi-use tire tool set
• Breaks the bead on most street and off road motorcycle tires
• Integrated tire spoon for tire removal and installation
• Light weight and compact size is perfect for tool packs
• Ergonomic handles with crossguard to keep hand from riding forward
• Forged 7075-T6 aluminum construction for strength and durability
• Black anodized finish
• Patent pending

Available in 9.5" aluminum (ideal for travel) and 16" forged steel (useful in a home shop/garage)

• Large display, readings are shown to 0.1 psi
• Kpa and Kg-cm2 scales also provided
• Reads up to 99 psi
• Ergonomic shape fits nicely in your hand

The Pro Fill Air Chuck from the people at Motion Pro is perfect for those tough to reach valve stems with its pivoting angled head. The design gives users extra hand clearance to avoid hot brake rotors or dirty chains. Billet manufactured from aluminum gives it a precise fit and function combined with light weight. It is finished off with a beautiful blue anodizing and then the Motion Pro logo is laser etched on forever. 1/4" NPT female inlet allows use with common air hose couplings and fittings.

A great addition to any tool box!

The MotoPressor Puncture Repair Tool combines the four tools essential for tubeless tire repair into a single tool.

With the motorcyclist in mind, they've designed a "4 in 1 multi-tool" that uses pre-vulcanized repair strings and packs into a sheath measuring a mere 130 x 68 x 50mm, that's small enough to fit in your pocket. The tool contains a pair of pliers, a rasp, an insertion tool and a sharp knife, which is all you'll need to fix 99% of punctures. The repair strings are pre-vulcanized, so they've done away with the "little tube of glue". The repair plugs the hole AND leaves a "patch style" repair on the INSIDE of your tire.

If you'd like to see the tool in action go just click HERE, and watch the demo.

Warp 9 stem puller

 Here is a list of the features of their CNC machined tool.

• Stainless Steel tip, wont break like softer brass tip
• Ribbed head for easier core removal
• Core tip threads into handle to protect tip from damage
• Includes spare valve core in handle for easy trail side repairs
• Tapered handle ends to make tip removal easier with gloved hands and non square edge doesn’t damage tool bags

Use simple leverage to easily lift your dirt bike up on to a flat platform.

The platform angle adjusts easily so either wheel can be off the ground quickly and safely for work or cleaning. These adjustments can be made with the bike on the stand.

Folds up for easy storage and transport.

Adjustable legs for use on any terrain and allows for even lift height for any dirt bike.

*Closeout item, as is, no warranty.

This Super Siphon has  a (1/2 inch x 6 foot) long hose, which makes it quite easy to transfer fuel from one bike to another! Simply, shake the hose to prime it and get fuel moving. The hose is resistant to gasoline and any other hazardous chemicals. Roll it up, stuff it in your bag and you will be very happy whenever you need it.

Made from precision-drawn, chrome-vanadium tool steel, the BikeMaster® 9-Piece Ball End Hex Wrench Set and Holder features a bead-blasted surface for a better grip and a corrosion-resistant coating. They have a ball end, allowing an angled reach and access to obscured bolts. It comes with a durable holder and manufacturer's lifetime warranty.

Comes with sizes 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm and 10mm

This Motion Pro tool pulls bearing out of those blind holes in engine cases etc. Set includes 30, 25, 20, 17, 15, 12, 10 and 8mm collets. 2 pound slide hammer. Crossbar type shaft allows easy collet removal. Necessary tool for most transmission rebuilds. Can be used for wheel bearing removal.

This brake bleeder makes bleeding your brakes a one man job.

The unique check valve allows fluid and air to escape while preventing air from re-entering the system.

Combines wrench and bleeder valve into one convenient and compact tool

• Fits most 8 mm bleeder nipples
• Bleeds brake systems and hydraulic clutch systems
• Internal check valve for fast easy bleeding
• Anodized billet aluminum handle with chrome moly steel body
• Compact size for tight spaces
• High quality internal seal
• Multi position handle

Keep your cables lubed up and working freely, with Motion Pro's Cable Luber. This tool is used to inject lubricant into any cable housing. Clamps over housing and cable allowing an aerosol can with nozzle to be connected. Once the lubrication solution runs out the far end, the cable is lubricated.

Designed to seal completely around the cable housing and stop all those messy leaks. With the unit closed and sealed around the cable, your cable gets better lubrication and you waste less lubricant.

• Works on most cables with a 4mm - 8mm O.D. housing.

• Contains degree wheel, standard unit indicator, adjustable magnetic stand, and three positive stops (10 mm, 12 mm and 14 mm threads)
• Can be used to install and adjust timing of any cam
• Wooden carrying case

A handy pocket size slide calculator from Mikuni to help you calculate jetting changes due to temperature and elevation changes. Will work for single and multiple cylinder machines whether 2 or 4 stroke. Also includes a guide for determining rich or lean conditions.

96 page 5th Edition Sudco Mikuni Carburetor Manual featuring the complete line of Mikuni RM, VM, HSR, HS, TM, TMX and BN Carburetors and Fuel Pumps with Parts Breakdown Diagrams, available Tuning Components, Tuning and Setup information of all Mikuni Carburetors & Fuel Pumps for Dirt, Street and Personal Watercraft applications.

Great resource for the do it your self rider to get the most out your carburetor.

• Accurately and quickly measures chain slack
• Two scales measure both chain slack and chain to swingarm clearance
• Setting chain slack properly dramatically improves chain life
• Lightweight compact design fits easily in your tool box or road kit
• Works on most street and dirt bike applications up to 75mm chain slack
• Made from engineered nylon with aluminum measuring scale
• Anodized laser-etched precision measuring scale
• Refer to your owner's manual for proper chain slack and procedure
• Patent pending

Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.

Can break or rivet chains from #35 to #530 like a pro.

kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.

kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.

NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.

Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.

The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!

Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.

• Will not harm O-ring chains
• Easily adjustable for all chain sizes

• PBR = press, break, rivet
• Innovative design will press, break and rivet 520, 525 and 530 chains with one convenient tool (not for use on 428 chains)
• Versatile design will remove chain pins, press master-link plates and rivet hollow nose and soft nose (quad stake) master link pins on O-Ring and non O-Ring type chains
• Easy-to-use design allows you to change tool functions by simply moving the position of the anvil block
• Indexing letters on movable anvil and body ensures correct tool configuration; simply line up the letter on the anvil to the letter on the body to get the configuration you need
• All components conveniently store on tool when not in use
• All steel construction with heat-treated components for strength and durability
• May be supported in a vise or held with included handle
• Great for the professional technician or DIY mechanic
• Compact and light enough to carry in a tool bag for trail-side repairs
• Patent Pending

Features:

• Versatile, light and super compact chain tool for adventure touring and long distance trail riding
• 6061 billet aluminum body, complete tool weighs only 230 grams (8 oz)
• Will break 520, 525, and most 530 chains and master links (maximum link width of 20 mm)
• Included steel press plate for removing and installing clip style press-on master link plates
• Innovative dovetail closure provides ease of use and superior strength
• Hardened steel thread insert on body provides strength and durability
• Includes durable cloth pouch for easy transport on your adventure
• Requires use of a 12 mm and 14 mm wrenches (not included)
• Does not rivet master links.
• We recommend using the Motion Pro PBR Chain Tool if you have a rivet style master link

This bright and compact 6-LED flashlight plugs right into your SAE battery charging socket for hours of light. In addition, it has a charging system check that lets you know if your bike is charging properly. It features a 40 inch cord so you can see in those out of the way places when you need to.

Quick release one-piece clamps that saves space. These are great for fuel lines, controlling wires, and can be used many times.

Comes with 4 each of 8mm, 9mm 10mm, and 12mm.

No special tools needed, from Helix Racing.