The Kawasaki KLR650 is a 651 cc single, liquid-cooled, 4-stroke, DOHC, 4-valves, dual-sport motorcycle intended for both on-road and off-road riding. It was a long-standing model in Kawasaki's lineup, having been introduced in 1987 and remaining almost unchanged through the 2007 model. The 2008 model was the first significant redesign of the KLR650 since its inception.
| Chain Size: | Front Sprocket: | Rear Sprocket: | Front Tire: | Rear Tire: | Spark Plug: |
520x106 | 15T | 43T | 90/90-21 | 130/80-17 | DPR8EA-9 |
Allows LED type turn signals (and low wattage flush mounts) to flash using a standard flasher unit. Connectors included. One kit works with 4 signals.
The Barkbusters 10 OHM Resistor Set for LED Indicator Lights will correct the flash rate of your auxiliary signal lights. Ready to plug in connectors make installation a breeze. These resistors are intended for Barkbusters LED Indicator Lights.
Features:
This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.
Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.
This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.
Fits Most Models
These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.
These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.
Replacement Halogen bulbs for mini style turn signals. Sold in a pack of 5 bulbs.
Roll-up pouch ideal for tucking away your lights when out on the trail.
Taillight and brake light Attaches to the top of the rear fender. Dimensions: 3 1/2" wide x 2" long x 3/4" tall. D.O.T. approved.
LED powered taillight, brake light, license plate light & license plate mount. Attaches to the underside of MX style rear fenders.
Taillight, brake light, & license plate holder (no plate light). Attaches to the underside of MX style rear fenders. Small and good looking!
Taillight, brake light, & license plate light. Attaches to the top side of enduro style (XR, KDX, etc) rear fenders. Dimensions: 2 3/4" x 4 3/4" x 2 1/2" tall. Wiring instructions included.
Taillight, brakelight, turnsignals, license plate light & license plate mount. Taillight is DOT approved, turn signals are not. Attaches to the underside of MX Style rear fenders. Turnsignals are embedded in the taillight housing. Wiring instructions included.
*Flushmount signals may require resistors to flash correctly
Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on 12-24 volt DC circuits.
Has both high and low beams. Attaches to the upper fork tubes with rubber straps. DOT and CE approved.
The indestructible, yet lightweight steel tube construction offers the best angle and ground clearance, makes it easy to jack up and provides stability - whether it's during maintenance or on the road. In most cases, you will no longer need to buy an additional swing arm stand. During long downtimes in the winter months, the centerstand helps take the load off your tires.
A billet aluminum side-stand from PSR. This is the side-stand you want when you are using lowering-links.
Has many height settings from stock to 2" lower, a must have when lowering your bike. Available in anodized black.
Double the size of your side stand footprint and half the chances of your KLR tipping over when parked on soft terrain. This laser cut, TIG welded 0.190" thick slice of aluminum bolts to your machine with just the addition of a hole in the stock side stand pad. Just takes minutes to mount.
These low peg mounts will drop your footpegs 1.5" and move them to the rear 1" for a much more comfortable riding position, especially for taller riders. Unlike relocation plates, these mounts do not hang dangerously below the frame. You can mount stock or aftermarket pegs and they are compatible with all skid plates, crash bars, and center stands.
New 10.9 high strength mounting bolts are included. Once installed the foot controls will need adjustment and the brake switch spring will need to be slightly modified.
Replacement Cleats for use with Fastway Pegs.
Inexpensive way of getting the factory look. Adds 1/2" of width to any standard foot peg. These will give you a much more stable platform when standing on the pegs.
Sold in pairs.
Not your average rubber insert! These rubber covers go over the top of your MK3 or MK4 Pivot Pegz so that the aggressive teeth are only exposed when you need them in muddy conditions.
Important to verify which style Pivot Pegz you have before ordering.
2 high-quality bushings per set. They recommend changing bushings every 40 hours or at least once a year to get the best performance out of a set. If you are on an Adventure Bike and are doing a lot of road miles they recommend swapping out bushings once a year to ensure that you get the most vibration dampening of the bushings.
Every new set of pegs comes with a 90A bushing installed. This is a medium flex rating.
80A is the softest and 95A lock-out is the stiffest and has the least amount of flex.
The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference.
The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.
For use on Motion Factory Foot Pegs Only
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".
The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option.
Wider foot pegs for sure-footed comfort.
17-4 cast stainless steel.
| Width | 1.97" |
| Length | 3.18" |
Services two Pivot Pegz and fits MK2, MK3 and MK4 Pivot Pegz
Kit Contents:
The ultimate Adventure peg, from the folks at Fastway - Pro Moto Billet. This peg is big enough to stand on all day with no fatigue, it measures 2.25" front to back and is 4.75" wide.
In addition to the big size, you can also adjust the camber with their patented FKMS Kamber bolt. ´Tilt´ your pegs to increase comfort, or to give better squeeze on your bike. You can further customize them with 3 styles of patented adjustable threaded cleats. Take your traction from comfortable to gnarly. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long.
These Adventure pegs are offered in several colors, but some colors may require extra time, call for availability.
Mounting these pegs to your KLR takes just a bit of work.
Please see link to the instructions below. These apply to the ADV and Evolution AIR Peg as well as the Evolution II pegs referred to in the instructions.
Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way. Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.
These AIR pegs are offered in several colors, but some colors may require extra time, call for availability.
Mounting these pegs to your KLR takes just a bit of work. Please see link to instructions below to see what you will need to do. These instructions apply to the ADV and Evolution AIR Peg as well as the Evolution II pegs listed on the instructions.
Motion Factory Racing patented Flex-Mount Footpeg System provides superior grip and allows your foot to flex forward and back with the movement or your motorcycle.
One of the key features of Flex-Mount Footpegs is their unique flex-mount design. This design allows the footpegs to absorb shocks and vibrations, reducing fatigue and improving overall comfort during long rides. Additionally, the adjustable height and angle options ensure a personalized fit, allowing you to find the perfect riding position for maximum control and stability.
The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference.
They put an a90 bushing on all new mount setups so people can get a good feel for their mid range option. The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.
Complete mount system includes:
They designed their hardware to bend rather than break in a significant impact. A wrench or adjustable wrench will quickly and easily bend the bolt back straight. Please avoid using a hammer. A little leverage from a long-handled wrench or pipe will do the job. The whole system is rebuild-able and serviceable.
They Fit Kawasaki KLX110 and Yamaha TW200 however some of these bikes may need a little modification by yourself, Please check the size carefully before you buy. If you make mods to the footpegs for fitments it will void all warranties and return policies.
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever!
Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.
This set of high quality replacement steering stem bearings includes:
A very popular modification. Eliminates the weaker 2 bolt setup in favor of one bolt all the way through for the upper subframe attach point. No more worry about keeping the bolts tight, or the original bolts breaking. If you have the SW Motech or Tusk crash guards you want this kit for sure.
This universal will give you both upper bolts, the upper spacer for the standard kit, and both lengths of lower bolts in case you have bars that use that point to attach.
Quality steel sprockets and EK SRO6 O-ring chain. We put them together to make a complete, affordable kit. Chain comes with clip type master link.
High Quality chain. Will need to be cut to fit your sprocket combination.
All of these chains come with a clip type master link.
Always carry a spare master link when out on the trail.
Master links are not interchangeable. Be sure to check the manufacturer and series on your chain.
These do not fit the TW200 or XT250. Only for 520 or 525 chains, Please verify chain size.
Individual 14T, 15T or 16T front sprockets.
JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.
Individual 14T, 15T or 16T front sprockets.
JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.
Quality rear steel sprockets.
A pack of 10 Fuji style lock nuts to put on the sprocket of your KLR650. These are an 8 mm, flanged type nut that will keep your sprocket snug and tight.
Polyurethane drive cushions for the KLR650. Polyurethane has a higher abrasion, cut, and tear resistance than rubber as well as much better resistance to chemical breakdown. This will offer longer life and better damping when compared to the rubber counterpart.
The KLR650 is rather hard on the cush drive rubbers. Replace these any time you feel excessive play in the sprocket hub. Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.
Genuine Kawasaki replacement chain guide. This guide mounts to the lower swing arm.
The chain slider protects the swingarm from contact with the chain. Replace yours before it wears through to the swingarm.
Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.
Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.
The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!
Can break or rivet chains from #35 to #530 like a pro.
kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.
kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.
NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.
Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.
Introducing Oinker®, the revolutionary chain lube attachment for dirt bikes, street bikes, and ATVs. Say goodbye to messy lubrication. Oinker® attaches to any chain lube or wax, ensuring a precise and even application to both sides of your chain. This means minimal overspray, keeping your swing arm, rear tire, and brakes clean.
*For cans with an attached smart straw, you will need to replace it with the included nozzle
What's Included:
Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.
This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).
Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.
Maximum master link width 24.8mm.
Will not damage master links, hardened steel pins for reliable use.
Light weight billet aluminum construction.
A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.
Fits 520, 525, and 530 pitch chain.
ULTIMATE SPROCKET WRENCH KIT
The ABUS SmartX 8078 3D Alarm Disc Lock offers advanced Level 18 security, combining cutting-edge technology with exceptional protection for your bike.
Featuring a 13.5mm double-locking sliding bolt made from specially tempered hardened steel, it delivers superior resistance to tampering.
The 3D motion-sensing alarm emits a powerful 100dB sound to deter unauthorized movement, while the SmartX Bluetooth keyless lock system provides ultimate convenience. It seamlessly connects to the ABUS SmartX App, allowing you to monitor lock, alarm and battery status in real-time.
The USB-C rechargeable battery ensures long-lasting performance and multi-color LED lights with audible signals keep you informed. The lock also features location memory from the last pairing, providing added peace of mind.
New from Warp 9, a full floating stock size rotor. These rotors have an additional hole for placement of a magnet for an electronic type speedo like the Vapor.
Includes a fresh set of brake rotor bolts.
Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.
Galfer's solid-mount Rear Wave rotors provide all the advantages of the front rotors when coupled with the floating rear calipers found on most motorcycles. Combining the best materials and manufacturing process, these rotors will handle everything you throw at them. Patented inner and outer Wave design minimizes heat transfer, equalizes dissipation and evens out pad wear.
Add bling and performance to your bike with a fresh new Warp 9 rear rotor!
Includes a fresh set of brake rotor bolts.
Galfer's Standard Wave rotors are engineered to provide the best performance in the market. Every aspect of our design, from the materials and manufacturing processes to the extensive testing, have been carefully chosen to produce the best quality stainless steel rotor available.
Kit includes:
New from Warp 9, a full floating 320mm Supermoto disc with caliper relocation bracket! These rotors have an additional hole for placement of a magnet for an electronic type speedo like the Vapor.
Includes a fresh set of brake rotor bolts.
Full braking power for your KLR650 supermoto conversion. 320mm oversized disc has a lightweight forged alloy center-hub and tough billet steel, 4mm thick brake rotor for maximum stopping power. Rotor rings include OD cooling groove and extra weight-reducing scraper holes and are riveted together with a nine-button sturdy rivet system.
DOUBLE-H SINTERED METAL PADS
Provide maximum brake effect and last twice as long as organic pads
Feature the HH friction rating – the highest in the industry
DOUBLE-H SINTERED METAL PADS
Provide maximum brake effect and last twice as long as organic pads
Feature the HH friction rating – the highest in the industry
Sintered Pads from EBC are the best pads we have found for the KLR, they provide good performance in all conditions yet still give you long pad life.
These sets include front and rear brake pads.
Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!
Set includes front and rear brake pads.
Semi-Metallic Compound
OEM replacement upgrade. Great feel, long lasting, and very little rotor wear with this durable compound. Compound applications for almost every need, including off road, street, touring, enduro, dual sport and more. Precision made in our Galfer factory in Spain.
Best Use: Our most popular compound! This compound is the work horse of the Galfer family and is a great OEM upgrade for the everyday rider.
Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!
Set includes front and rear brake pads.
Semi-Metallic Compound
OEM replacement upgrade. Great feel, long lasting, and very little rotor wear with this durable compound. Compound applications for almost every need, including off road, street, touring, enduro, dual sport and more. Precision made in our Galfer factory in Spain.
Best Use: Our most popular compound! This compound is the work horse of the Galfer family and is a great OEM upgrade for the everyday rider.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Repair kit for your front disc brake caliper.
Each kit includes all necessary rubber components and brake pins.
Each kit includes all necessary rubber components and brake pins.
Each kit includes all necessary rubber components and brake pins.
All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.
Made by Nissin, an OEM supplier in Japan
All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.
Made by Nissin, an OEM supplier in Japan
Replacement retaining pins for the brake caliper. Includes 2 stock style brake pins.
Be sure to use some anti-seize on the threads when you install them.
Rear caliper only for DR350 and DR650.
This anodized billet piece, brings a touch of color to your bike. Available in red or blue, it replaces the stamped steel clevis that connects your brake pedal to the master cylinder.
This brake bleeder makes bleeding your brakes a one man job.
The unique check valve allows fluid and air to escape while preventing air from re-entering the system.
Combines wrench and bleeder valve into one convenient and compact tool
A kit consisting of 15 (9 front - 6 rear) KLR650 rotor bolts, enough to do the front and rear.
Class 10.9 steel rotor bolts provide excellent sheer strength and include medium-strength threadlock patches to securely fasten your rotor
Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. Designed by Rick at Cogent Dynamics on his high-tech suspension dyno, then tested and endorsed by KLR owners all over, these units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the units under the springs and hit the trails.
If you weigh up to 250 pounds, select the .64 spring kit. If you are over 250 or carry lots of luggage, please select the .70 spring kit. Please call if you have any further questions.
All of these kits include DDCs, springs, fork oil and preload spacers.
The complete fork upgrade kit - Progressive Suspension springs and Race Tech emulators. Also includes a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
A dual-rate fork spring for the early KLR650. These springs start with a .40 kg/mm winding and after approximately 20% of the stroke, stiffen up to .60 kg/mm for the remainder of the travel. A very nice improvement over the stock springs which are .40 kg/mm for the entire travel.
Developed by the KLR suspenison experts at Cogent, this set of springs will stiffen up that wimpy KLR front end. Choose between .64 kg/mm springs (60% stiffer than stock) or .70 kg/mm units (75% stiffer than stock).
Will not work for 2014-Cur 'Mid-Year' New Edition Model
Progressive springs offer a soft initial spring rate for a plush ride. Progressively wound design provides increased resistance to bottoming as spring compresses. These springs are significantly stiffer than the wimpy stock springs.
They will make a big improvement in the front forks while still delivering a smooth ride. Sold in pairs.
Race Tech has developed these fork springs specifically for the heavier weight of the KLR650.
Sold in pairs.
These will not fit the Tengai model.
Race Tech has developed these fork springs specifically for the heavier weight of the KLR650.
Sold in pairs.
Not for 2014-2018 New Edition
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.
Stiffer fork springs are recommended to get the full potential of the DDCs.
You can adjust the preload on your KLR shock easily, why not on the forks as well? These caps give you the capability to adjust the spring preload in your forks to match your load.
Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.
Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward.
Simple to install and completely tunable for all conditions and rider preferences.
Both kits include all bushings, snap rings, and washers.
Gen 2 kit also includes the necessary O-rings.
Gen 1 kits are OEM bushings, snap rings and washers.
Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes 2 Fork Seals and 2 Dust Wipers.
An excellent replacement for the stock fork boots. These are great for protection from dirt, rocks and other contaminants. These boots utilize the latest advances in material technology to adapt to fork and styling demands. These high quality fork boots are 1/4 the price of the OEM factory replacements.
| Top Diameter | Bottom Diameter | Length |
| 42 mm | 45 mm | 60mm |
Fork brace precision machined from aluminum barstock. Drilled and tapped for optional lower fender attachment.
Hard anodized black for corrosion protection. Fits OEM forks. Split design allows for installing in minutes without having to remove the forks.
