Our offices will be closed on Tuesday, December 24 and Wednesday, December 25 for Christmas. We will be back on Thursday, December 26. Happy Holidays!
The Honda CRF250L is powered by a liquid cooled single cylinder 249cc four stroke engine mated to a 6-speed transmission. The CRF250L weighs 321lbs and has a ground clearance of 10 inches with a seat height of 34.4 inches. The fuel tank has a capacity of 2.1 gallons.
|
Chain Size: |
Front Sprocket: | Rear Sprocket: | Front Tire: | Rear Tire: | Spark Plug: |
|---|---|---|---|---|---|
| 520x106 | 14T | 40T | 3.00-21 | 120/80-18 | SIMR8A9 |
Higher pressure in the cooling system, raises the coolant boiling point and increases protection from coolant loss due to overheating.
23 PSI - 1.6 Bar.
Driven Engine Block-off Plates will stop the annoying and possibly damaging backfires from occurring while allowing you to remove a few pounds in associated valves and hoses from your bike. On late model EFI bikes with O2 sensors, ESPECIALLY when using Dynojet's Power Commander 6 with the Autotune feature, the air injection system MUST be blocked as it will introduce additional oxygen into the system which will skew your O2 sensor's values and make it impossible to get a correct tune.
Our kit includes 5 EBC friction plates which eliminates the judder spring assembly by replacing it with a 5th friction plate.
Heavy duty clutch springs by Barnett are included it this kit which will significantly decrease wear under high stress conditions.
Includes genuine Honda friction plates, drive plates, and clutch springs.
Barnett clutch springs are made from the finest materials available.
Heavy Duty Barnett clutch springs are pre-set, shot-peened, and heat treated for performance and durability.
High quality stator cover gasket.
Includes all necessary top quality gaskets for top end rebuilds.
Genuine Honda replacement oil filter cover gasket.
Providing unbeatable performance and exceptional value, Hi-Flo is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide.
Grab our 5-pack and save both time and money!
Providing unbeatable performance and exceptional value, Hi-Flo is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide.
Grab our 5-pack and save both time and money!
Extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
12mm Thread, 17mm Head.
A 10-pack of drain plug sealing crush washers. Replace your sealing washer at every oil change to prevent a leak.
Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.
Thin wall bi-hex sockets designed to access narrow spark plug holes.
Fits 3/8" square drive and hex drive, 14mm, 16mm, 18mm, 21mm.
Iridium spark plugs are made with premium quality materials.
Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.
Sold individually, unless otherwise stated.
Laser Iridium
With the smallest tip diameter available, OE Iridium spark plugs provide superior ignitability and long service life. The iridium/platinum surfaces ensure a slow wear rate, providing stable idle and superior anti-fouling.
Genuine Honda Factory Service Manual specifically for your CRF250L
Made from medium carbon steel with hardened jaws. It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. Made by Motion Pro.
This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.
Includes all necessary top quality gaskets, and seals for engine rebuilds.
For easy removal of recessed oil filters.
Conical point screws pierces and grabs the metal end cap of the filter.
reduces potential damage to the engine cases.
NOT for use on re-usable oil filters.
A 3-pack of easy to apply strips measure the temperature of engine, suspension, and radiator components. Temperature range 149° to 248°
Thread Chasers are designed to clean and re-cut damaged aluminum threads.
This kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.
Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.
Uses 8mm or 10mm hex sockets, a Must for all tool kits.
