Lighting

This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.

The stock tail light, blinker and license plate bracket is rather large and cumbersome, to put it politely. The B&B Off Road Engineering unit is simple and tidy and gives you a LED tail and brake light unit, a LED license plate light and turn signal mounts as well.

Installation is easy - remove the stock unit and bolt the new unit in the same location. Off with the old and on with the new in minutes. All necessary hardware included.

Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.

Also works with Edge-2 Circuit Board Upgrade.

The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail/stop light function. 3 white LED's are used for license plate illumination.

Included is a set of turn signal brackets that bolt to the mount, but these are designed for a smaller LED type signal with a mounting stud of just 8mm. If you think this might be a problem, look at the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!

NOTE: LED's must be installed on a 12 V DC system!

There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.

You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.

• Plug and Play
• 7 Different Programmable Turn Signal Patterns
• Safety Brake pulsing built in (Can Enable or Disable)
• Superbright LED's; For excellent brightness, even in direct sunlight
• License Plate Light built in
• License Plate Bracket fits the common USA license plates, sloted for maximum plate compatibility.
• Includes Mounting Hardware
• Saves about 2 lbs over the factory tail light setup
• Made In the USA

We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.

This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.

• Adds 3 light modes to your tail light
  • Brake light modes: Strobe Alert, Intermittent Pulsar, and Pulsar
• Plug and play wire harness eliminates the need for wire cutting, splicing, or soldering
• Removable capsule cap enables easy selection of your desired light mode
• Provides a valuable safety feature that demands attention while you are slowing down or coming to a stop
• Simple and easy installation
• Handles up to four amperes of current
• Built-in fail safe pass through for enhanced safety

This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.

Features:

• Independently programmable flash speed, flash duration, and pre-delay
• Works for LED or Standard Bulb Tail Lights
• All Solid State design
• Meets or exceeds OEM load rating specifications
• Over 1000 possible flash pattern combinations
• Simple programming setup with your brake lever
• Extremely compact unit size; 20mm x 20mm x 12mm

Fits Honda CRF450L Motorcycles (Front Turn Signals)

OEM Fit Left Front and Right Front turn signal connectors with wires pre-attached.

This kit is specifically for attaching After-Market turn signals to the front of the CRF250L / Rally or CRF450L.

The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.

You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.

Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.

There are many options and configurations using this electronic tool.

No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.

This relay will fix your flash rate problem caused by aftermarket signal lights and/or integrated tail light. If your signal lights flash too fast or do not flash, this part is your solution! Plug and play - easy installation.

Only ONE relay is needed per motorcycle regardless of front and rear signal set-up.

• Slows signaling flash rate back to the normal rate when your bike goes into hyperflash state (or your signals stay on constantly)
• Adjustable functionality to speed up or slow down flash rate to your preference
• Plug and play installation: simply replaces the relay already on your bike
• Fits like OEM
• Relay housing is flexible so that you can access the adjustment dial inside the unit

This component works with the following signal configurations:

1. All stock
2. Stock taillight, aftermarket signals
3. Integrated taillight, stock signals
4. Integrated taillight, aftermarket signals.

The relay comes preset to 85 cycles per minute. You can alter the flash rate to make it faster or slower. If you slip off the grey cover you can access an adjuster that will enable you to change the flash rate to your liking.

Please make sure your bike uses a 2-pin relay for the signaling system. If your bike has hazard lights it may need the 4-pin relay. Please also note the pin configuration and make sure it matches what is on your bike. It is very important to verify fitment before making your purchase.