Lighting

Made from heavy duty 1/8" thick stainless steel, these mounting brackets are specifically designed for mounting 2" LED auxiliary lamps to the front of your TW200. They position the lamps (not included) high & tight to the bike for optimal protection and light projection without interfering with the bike controls, body work, or fuel tank. Kit includes four longer mounting bolts for the lower triple clamp.

The image shows a GoPro camera on the TW's right side and an LED light on the left. You could certainly do something like that as well!

This auxiliary light bar is laser-cut from mild steel and powdercoated black for exceptional looks. The holes on each end of the bar are 3/8" and should not be made any larger for strength reasons.

The bar is very easy to install, just remove two plastic "pop" connectors and install the bar with two bolts with clips. All hardware and instructions are included.

For LED Auxiliary Lights

From our friends at JNS Engineering, a very nice mount for a set of auxiliary lights on the front of your XR650L. Laser cut from 0.190" 5052 aluminum it is CNC formed and then powdercoated black. (image shows bare aluminum, but yours will be black) One of the best benefits is that it will not interfere with even the largest aftermarket fuel tanks. Includes stainless steel mounting hardware.

When usefulness and quality matter the Cyclops Auxiliary light kit for the Yamaha T7 comes shining through and leaves the competition in its wake.

The usefulness of having lights that turn direction with the bars can be very beneficial, perfect for those evenings that might have gone a little long and you need to set up camp or pick your way through a tighter section of trail.

Usefulness from having the ability to run daytime running lights and have full control of low beam settings as well as a switch to disable the system leaving only DRLs on. (Dimmer with cutout switch)

Simplicity for those that don't want to add ANY switches to their bikes, you can choose to have the aux lights activated in a reduced power on low beam (50%) and high beam (100%) via the factory high beam switch by choosing the dimmer option with no switch. We don't like extra switches on our already cluttered bars, Do YOU?

Or have the lights on in high beam and off in low beam, with no switches. Option (I do not want dimming or any switch, Aux lights turn on with factory high beam switch)

If choosing the DRL version, DRLs will be on with the key. By choosing a switch you can disable the main auxiliary lights leaving only the DRL ring on during the daylight. Then at night, flip the switch and have full control of your main auxiliary lights activating in conjunction with your bikes high and low beam, this works very well with the ON with high beam OFF in low beam, No switch option.

With this Cyclops kit you can choose what works best for you. 

Benefits of a 100% plug and play setup utilizing all factory Yamaha connectors. If using diming, The high beam wire does use a positap, By far the best way to tap into a wire without causing damage, no tools required.

The basic kit uses our tried-and-true Aurora 2-inch diameter, 19 watt (38 for the set) light kit, All CNC machined, polycarbonate lenses and super lightweight. Each light is rated at 2000 lumens (4000 for the set) with a 15-degree optic throwing a light beam nearly 500 ft

You can choose the DRL or non DRL version.

If no dimmer option is chosen the kit will come with a switch to turn the lights on or off, If you chose the dimmer option you can install the lights with No switch, The auxiliary lights will work in conjunction with the factory headlight, Low beam is set at 50%

With the DRL option, you can also choose the cutout switch, this will disable the system, this works well with the DRL, allowing you the ability to turn the main aux lights off and run with only the DRL halo rings.

They offer mounts for the stock low fender or the Camel ADV high fender kit.

 Emark certified for your confidence when riding in countries that require this certification.

Look at these quality features!

• Solid Steel cradle mount. No broken or cracked mounts!
• CNC machined aluminum housings.
• Poly-carbonate lenses, Break-proof!
• 15-degree beam patterns, a great choice for distance and field of view.
• 19 watts each
• 2000 lumens a piece, 4000 lumens for the set.
• 5500K
• Input voltage 9-30VDC
• R113, R10 TUV and Emark certified.
• IP68 Rated
• Warranty....5-year Function warranty (crash damage excluded)

An aluminum Light Mount for your bike. Put whatever light you like up front for more light as well as great daytime visibility to other vehicles. Win-win situation. Choose the Single Mount or Double Mount.

The perfect solution for mounting those LED auxiliary lights. The base of the RAM mount is held by your mirror. This puts the light where you can easily adjust the angle for different riding situations. This mount fits VisionX Solstice lights or any other light with a 6mm or 1/4" hole in the mounting bracket.

This is for Mount Only. Sold individually.

10 Watt LED lights sold separately.

From our friends at JNS Engineering, a very nice mount for a set of auxiliary lights on the front of your KLR650. Laser cut from 0.190" 5052 aluminum it is CNC formed and then powdercoated black. One of the best benefits is that it will not interfere with even the largest aftermarket fuel tanks. All included mounting hardware is stainless steel.

JNS has come up with another great addition for the little XT250. Auxiliary light mounts that keep the lights up high for great projection, but still good and tight to the bike for protection. These heavy duty 1/8" stainless steel mounts put your lights out of harms way without interfering with controls, body work, or the fuel tank. Includes four longer upper triple clamp bolts. Everything but the lights themselves to light your way through the darkness.

A game changer in auxiliary lights. High output, compact and lightweight!

The New Cyclops Aurora 2 inch lights rated at 4000 lumens combined. Using an authentic top binned Cree XHP50 emitter these lights pack a punch!

Available with or without the daytime Running light option (DRL) which can also be a front blinker. (you may need an LED flasher to do that)

Like all Cyclops lights we only use the Best Real Cree emitters. R113, R10 TUV and Emark certified IP68 rated.

Includes a full relayed wire harness designed for a Motorcycle. No need to use a switch if running the DRL version, also no need for a switch if using the skene dimmer or want the lights on in high beam and off in low beam. The factory switch will work for these applications. Unless you have a LED factory headlight in a R1200gs, 850Gs, or KTM1290 these bikes will require our Raider canbus controller.

Look at these quality features!

• Solid Steel cradle mount. No broken or cracked mounts!
• CNC machined aluminum housings
• Polycarbonate lenses, Break-proof!
• 15 degree beam patterns, a great choice for distance and field of view.
• 19 watts each
• 2000 lumens a piece, 4000 lumens for the set.
• Includes a relayed wire harness
• Input voltage 9-30VDC
• R113, R10 TUV and Emark certified
• IP68 Rated

Now a lifetime warrantied LED light set at a budget friendly price.

The new Cyclops Pegasus led light set comes complete with a high quality relayed wire harness and a potent combo light beam pattern.

We are able to offer this fantastic light at a great price due to a one piece optic and sealed beam construction, eliminating extra parts and creating a very durable and high performance light.

These lights in white feature 7 watt emitters (28 watts per light) with two 10 degree and two 25 degree optics, Good for 500 plus ft of lighting (white).

The amber version is a Cree 3 watt emitters (12 watts per light).

This combo beam pattern offers good forward lighting and extremely good conspicuity.

The light set is available in white 5600K or a extremely bright Amber, perfect to allow those autos to see you. Lightweight and robust at 2.75 inches with a single stud mounting, they fit just about anywhere you would like to mount your lights.

Specs:

• Canbus compatible, full relayed wire harness included
• 5000 plus lumens for the set
• 28 watt draw per white light, 12 watt draw per amber light
• ISO 67... waterproof
• 5600K (white 33% brighter than Amber)
• Life time warrantied
• Sold as a pair

Use these brackets to mount your light weight auxillary lights or turn signals. They will bolt directly on to the DR650 lower triple clamp bolts. This makes for a clean 'tucked in' installation. Sold in pairs.

The Mojave Series LED Racing Lights have been designed to survive and operate in extreme conditions. Lights feature a heavy duty housing that can withstand hard impacts and a lens that is twice as thick as traditional lights. The light includes three different replaceable lens (Flood, Spot, and Combo).

Features:

• Heavy Duty Design​
• IP69K Rating​
• Flood, Spot / Flood, & Spot Lens Included
• Stainless Steel Bracket & Hardware​
• 5,000k Light Color – Natural Daylight
• Heavy duty black steel left & right mounting brackets to bolt directly to your lower triple clamp.
• Harness with Switch

This kit will work with the 6.6 Gallon Acerbis fuel tank for the DR650. You must run the light brackets inwards in order for there to be proper clearance with the 6.6. Gallon tank.

This kit includes 2 auxiliary light mount brackets. These brackets are designed to mount to most lower triple clamps. New longer bolts are supplied to accommodate the thickness of the bracket. These brackets are powder coated black for a sleek and long lasting finish. The brackets can be used to put the addition of new lights to the outside of your forks or swap the brackets and the lights can be mounted inward to give more clearance for bigger shrouds or fuel tanks.

These heavy-duty aluminum brackets are laser cut from 0.190" 5052 Aluminum then powdercoated black. Designed specifically for mounting auxiliary lights to the front of your DR650, the mount goes between the fender and the lower triple clamp. Longer fender bolts are included in each kit. installs in 10 minutes.

Three options are available: two different dual mounts that place the lights outside the fender and a single, center type mount. The 2" mount is for smaller type lights and is 8-5/8" between the mounting holes while the 3" is 10-3/8" between the mounting holes. If you are going to use larger style lights, the 3" mount is for you.

Note! The Dual 2" and 3" mounts do not work with the Acerbis 6.6 gallon tank! They make contact prior to full lock. Mounts are fine with other oversize tanks.

A nice place to mount auxiliary lights on your KLX where they will be high and easy to reach for adjustment but still tight to the cowlings. They will not interfere with controls, body work or the fuel tank.

Constructed of 1/8" stainless steel they are intended for LED lamps in the 2" range, but with a slight slotting of the mounting holes, will work great with 3" lights as well. Includes longer bolts to for the upper triple clamp mounts.

This is a plug & play low profile LED light bar kit which includes laser cut stainless steel mounting brackets and high quality wire taps.

IMPORTANT: Must be used in conjunction with LED headlight or bulb that consumes no more than 35W.

  Please note that this product is not compatible with the 1987 TW200.

Each 10 watt Solstice Solo produces 900 lumens, which is roughly equal to a 50 watt halogen bulb. These are one of the brightest LED off road lamps on the market. The rugged and compact 2” x 2” square die-cast aluminum housing makes mounting easy. The Solstice Solo also features a 4 sided channel design that allows you to interlink it on all four sides with other Solstice Solo pods. Includes stainless steel mounting bracket and waterproof connection. Choose narrow, medium, wide or elliptical light beam pattern. Our favorite is the Elliptical pattern which is wide and flat, putting most of the light where you need it the most.

Sold each.

Available in two wattage configurations: 30 watts and 42 watts, which produce luminous outputs of 5000 lumens and 7000 lumens, respectively. If your motorcycle's electrical system cannot accommodate these wattages, the light can be operated in low beam mode, resulting in a 50% reduction in power consumption. When additional illumination is required, users can easily switch to high beam mode.

Despite its compact size, this LED light is designed to deliver substantial luminous output. Its performance surpasses that of other mini LED lights in the market.

The light is equipped with a durable push-button switch, metal handlebar mounts, and adaptable options that allow for compatibility with various motorcycle configurations. It features components such as switches, cords, strain reliefs, and optics that are engineered for enhanced water resistance, robustness, and overall performance.

Tailored specifically for snowbike applications, this light boasts a compact design with significant output capabilities. Enhanced heat is directed to the lens, facilitating snow melting and enabling continuous riding.

This light is ideal for users seeking a lightweight solution to comply with legal requirements for headlights while also being sufficiently powerful for racing and trail riding.

Installation is straightforward, with the light mounting easily to a number plate; however, the use of the recommended stainless steel platform mount is advised for improved convenience. The light operates using the motorcycle's battery power.

The Explorer light bar is equipped with a GoPro-compatible mount and an aluminum platform, allowing for versatile mounting options. A handlebar mount is provided for central positioning on the handlebars. (Fits all stock 7/8 and 1 1/8 bars. Not for flexbars) Notably, there are no plastic components in the light head assembly.

Included with the product is a rubber-covered switch that can be mounted on the handlebars, offering three power settings: off, 50%, and full brightness.

The light features a combo beam pattern, integrating spot, driving, and wide beam configurations into a single unit.

This auxiliary light harness is specifically built for the DR650 using the highest quality materials and components. Wire lengths, component locations, and end terminals are all predetermined and assembled for you. No electrical expertise needed! The relay is wired directly to the battery and Posi-Tap connectors are used to tap in to the existing headlight high beam circuit.

This eliminates the need for a separate switch to operate your auxiliary lights. When your high beam is on, your auxiliary lights will be too. Back to low beam and those high-powered beams will be off so you don't bother oncoming vehicles. There's also an in-line fuse holder for safety and peace of mind. A simple one page instruction sheet is included.

Now available in the original version or the Ultra version. The original uses the front two emitters for low beam and then switches to the rear two emitters for high beam. The Ultra uses the front two emitters for low beam and then runs all 4 emitters on high beam at a reduced wattage. Wattage is 38 watts on low and 38 watts on high.

This bulb uses 4 Cree XHP 50 emitters, capable of more than 2500 lumens each. At 5000 lumens on each function, this is the brightest Cyclops H4 bulb.

• All metal construction for bases and collars
• Better thermal efficiency 
• Better beam pattern distinction between high and low beams
• 5600k
• 38 watts 
• Removable metal base plate for easy install.
• Screw on connectors at driver
• Standard H4 connector
• High/Low Beams

*UNIVERSAL PART, PLEASE CHECK YOUR APPLICATION FOR FITMENT

This powerful LED headlight upgrade kit allows your bike to be seen better by other motorists during the day and also gives a much improved headlight for night time riding. 

Includes two 4000 lumen Phillips-chipped LED Headlight bulbs and proper spacers that take the place of factory adaptors

- Anti-glare Tips
- 8000 Lumens
- IP68 Rated
- 5800K

- One Year Warranty

Please note: This kit may require the headlight retainer springs to be manipulated.

This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.

Replacement Halogen bulbs for mini style turn signals. Sold in a pack of 5 bulbs.

This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, no drilling, no wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.

This kit is available with either a chrome or black chrome reflector in the headlight.

Does not fit '87 TW200 because that year has a unique AC powered headlight circuit.

This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, drilling, or wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.

This kit is available with either a chrome or black chrome reflector in the headlight.

Check out the images for stock vs. LED patterns and brightness. (Images are of a DR/DRZ unit, but the light unit is the same as that on the XRL.)

Has both high and low beams. Attaches to the upper fork tubes with rubber straps. DOT and CE approved.

Years in development, Yenkro Adventure Rally Fairings have been designed from the ground up to withstand even the most unforgiving terrain and now the gen 2 kit takes it to the next level. Battle-tested in conditions that only the Australian outback can muster, this fairing is a must for adventure riders from all corners of the globe.

Side Panels are Optional and Sold Separate, they work with Acerbis 6.6 gallon (25L) tank only. Available in either black or white.

Can be purchased with or without side panels.

Standard kit includes:

• The main tower assembly with all the mounting brackets to suit your bike
• Speedo bracket which also holds the stock wiring loom.
• 1 Short screen
• 1 Tall screen
• Hella halogen lights (upgrade to led by adding the upgrade option to your cart)
• Qc3 usb charge socket
• Plug and play wiring for lights and usb.

This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a one beer, plug & play installation.

This is the best performing and highest quality headlight they currently offer.

The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive, ie USA).

The high beam is amazingly bright eliminating the need for auxiliary lighting.

The materials, construction, and aesthetics are all top notch. You won’t be disappointed!

Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive. (USA)

This is the ultimate headlight upgrade for your XT250! It’s a plug & play kit which includes the newly released Morimoto round headlight with preassembled aim adjustable mounting bracket set. Installation takes five minutes and the light output is phenomenal.

Low Beam: 2,400 Lumens, 20 Watts
High Beam: 4,300 Lumens, 35 Watts
Color Temperature: 5,000K
Warranty: 5 Years

This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, no drilling, no wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.

Now available with a black chrome reflector!

Check out the images below for stock vs. LED patterns and brightness images.

  Fits '87-'07 only

This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 2008-2018 Yamaha XT250. The new design for the black headlight produces more light and has much more uniform beam pattern when compared to the previous version. New design currently only available in black, chrome may be available in the near future. No wiring, soldering, resistors, trimming, drilling, or fabrication required.

• Low Beam: 20W, 3,600 Lumens
• High Beam: 40W, 4,500 Lumens
• Color Temperature: 6,500k
• CREE LED Chips
• DOT & SAE Approved
• CE, RoHS, ISO9002, IP67

Modern LED technology with a classic look!

This plug & play kit is built around the all new Holley RetroBright LED headlight which comes in three different colors.  

Choose from Classic White (3,000K), Modern White (5,700K), and Euro Yellow.  The RetroBright also features a replaceable bulb.
 

Low Beam: 25W, 2,000 Lumens
High Beam: 30W, 3,000 Lumens
Color Temperature: 3,000k or 5,700k
DOT Compliant
Beam Pattern: Left Hand Drive (USA)

Modern LED technology with a classic look!

This plug & play kit is built around the all new Holley RetroBright LED headlight which comes in three different colors.  

Choose from Classic White (3,000K), Modern White (5,700K), and Euro Yellow. The RetroBright also features a replaceable bulb.
 

Low Beam: 25W, 2,000 Lumens
High Beam: 30W, 3,000 Lumens
Color Temperature: 3,000k or 5,700k
DOT Compliant
Beam Pattern: Left Hand Drive (USA)

Does not fit '87 TW200 because that year has a unique AC powered headlight circuit.

So you say you want more light for your dual sport? Give this 7"DOT legal Rally light a try and light it up like a freight train! HIGH/LOW operation and SAE/DOT/E4 approved. 
 This light does not have the large Cyclops logos shown on one of the images.

• Race Inspired Design
• Hella reflector, made in Germany  stamped SAE/E4
• Lightweight Aluminum Frame
• Plug and Play for Bikes with H4 Bulbs.
• Available with optional mounting plate for computer or GPS
• Easily converted to HID if desired, uses an H4 bulb
• For bikes that are not H4 (XR650R), a simple H4 plug available at any auto parts store will allow you to use this light.
• Now the panel on top of the light for mounting speedos/gps's etc is included, (This is a platform, not actual GPS mount.)

Optional 10.0 Lumen LED High/Low Upgrade  and now the Phoenix LED complete headlight for the ultimate DOT headlight
The stock lamp that comes with this rally light is great, but you can get  well over double the brightness  with the LED upgrade at a substantially lower power draw. Note if your bike is ac powered at the headlight you will need the rectifier for the LED option.. AKA carbureted KTM's CRFX and XR400/650.. others may apply.

This kit includes the all new Morimoto 4×6 LED headlight and a pre-assembled JNS Engineering adjustable mounting bracket set. Like the rest of the JNS headlight kits, installation is a simple 5 minute plug-and-play procedure.

This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform/controlled, and features a proper upper cut-off. The high beam is amazingly bright, eliminating the need for auxiliary lighting (money saved!). Plus the 5,000K color temperature is extremely easy on the eyes. The materials, construction, and aesthetics are all top notch.

It’s a next level headlight, you won’t be disappointed.

Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive

Does not fit '87 TW200 because that year has a unique AC powered headlight circuit.

This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a plug and play installation however a small amount of trimming on the backside of the plastic headlight shroud is required.

This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive). The high beam is amazingly bright eliminating the need for auxiliary lighting.

The materials, construction, and aesthetics are all top notch. You won’t be disappointed.

Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive

These thumb-screws replace the stock headlight adjustment screws. These adjusters make it much easier to keep your headlight aimed properly. This is even more important if you are running the HID headlight as it is very easy to dazzle oncoming traffic if your headlight isn't aimed correctly.

• Sold in pairs.
   

This LED headlight from JNS Engineering is DOT approved and an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and mostly plug and play. The DOT kit does not have a daytime running light (parking light) and may require minor trimming on the backside of the fairing. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb. The primary advantage of this kit over the original is the DOT/SAE markings and a wider high beam pattern.

Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Compliant
CE, RoHS, ISO9002, IP67

This new and improved DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware. No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.

We highly recommend this kit over the non-DOT and original DOT kit.  The low beam has extra punch and a proper beam pattern cut-off.  The high beam throws light far and wide.  It’s already a crowd favorite!

Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.

Low Beam: 20W, 2,800 Lumens
High Beam: 35W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Compliant
CE, RoHS, ISO9002, IP67

Please note: Fits '87-'07 (Gen 1) only

Good News: There’s finally a plug & play LED headlight conversion kit for your 2008-2020 WR250R and WR250X!

This kit includes a sealed LED headlight assembly with plug & play electrical connection, adjustable powder coated steel mounting bracket set, and mounting hardware. 

Installation is a five minute, one beer exercise. If you can change a residential light bulb you will have no problem installing this conversion kit. We promise.

Please note that you will need to reuse your OEM upper headlight mounting grommet and two aim adjustment springs.  Or add new ones to freshen up your whole headlight unit.

Low Beam: 2,100 Lumens, 20 Watts
High Beam: 2,800 Lumens, 30 Watts
Operating Voltage: 10V-30V DC
Color Temp: 6,000K
Lifespan: >50,000 hours

This kit includes a DOT LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.

How does this headlight compare to our original TW200 kit? First and foremost, this kit has SAE/DOT markings and a much wider/brighter high beam pattern. The low beam is very similar to our original kit: wide, flat, and bright but with more punch. The DOT headlight assembly has also proven to be more durable than the original headlight.

Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Approved
CE, RoHS, ISO9002, IP67

No cutting, drilling, or wiring modifications! Installation takes 5 minutes.

Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.

  Please note that this product is not compatible with the 1987 TW200.

This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 1996-2020 DR650SE. No wiring, soldering, resistors, drilling, or fabrication required however due to the size of the headlight minor trimming on the backside of factory plastic headlight fairing is needed in non-visible areas.

• Low Beam: 25W, 3,600 Lumens
• High Beam: 40W, 4,500 Lumens
• Color Temperature: 6,500k
• CREE LED Chips
• DOT & SAE Approved
• CE, RoHS, ISO9002, IP67

This DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.

No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.

This kit is highly recommend over the non-DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!

Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.

• Low Beam: 20W, 2,800 Lumens
• High Beam: 35W, 3,600 Lumens
• Color Temperature: 6,000k
• DOT & SAE Compliant
• CE, RoHS, ISO9002, IP67

This kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.

The headlight features two primary sets of LED projectors, a wide low-beam pattern with distinct upper cutoff and a center spotlight high-beam for long range visibility.

The low-beam consumes 20W and remains powered when the 15W high-beam is fired. There is also a daytime running light feature which can be powered for additional glow. The LEDs are rated for 50,000 hours and operate at a 6000K color temperature.

No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.

Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.

Non-DOT

Headlight is DOT approved. Has both high and low beams. Attaches to the upper fork tubes with rubber straps. Turn signals are embedded in the headlight housing.

  Integrated turn signals may require resistors to flash correctly.

• Waterproof, long-lasting marker light bar uses less power
• Features 180° visibility
• White LED color
• Can be used in any position; refraction of light depends on position
• Measures 38mm x 9.8mm x 18mm
• Not for use where DOT lighting is required.

License plate bolt with bright white LED light. The simple way to light up your plate.

License plate holder has been designed to replace the bulky standard assembly with a sturdy, neat unit. The Tail tidy accepts the standard Yamaha blinkers and is supplied with a LED number plate light.

• 3 piece CNC machined from high-quality alloy
• Designed to bolt straight into position with no modification to the bike
• Available in polished or black ppa coated

This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.

Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.

License plate light with 5 LEDs. Compact and easy to mount. Meets plate illumination requirements with super white light.

This is for the LED license plate light ONLY.

The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail / stop light function. 3 white LED's are used for license plate illumination.

Included is a set of turn signal brackets that bolt to the mount, but these are designed for a smaller LED type signal with a mounting stud of just 8mm. Or consider the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!

NOTE: LED's must be installed on a 12 V DC system!

Clean up the backside of your TW200 and upgrade to a brighter, safer LED taillight in one go!

The Tidy Taillight Kit includes a durable, high-quality steel mounting bracket that mounts under your rear fending using the existing bolts. The bracket also has slots to mount your license plate.

The included LED taillight helps make your TW more noticeable to other drivers at night, and the super-bright LED brake lights activate more quickly than stock incandescent bulbs when you get on the brakes, giving drivers behind you more reaction time. The taillight unit also features white LEDs on the underside to light up your license plate and keep you legal.

Eliminates the big clunky rear sub-fender. Makes your XT250 look clean and sporty.

The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail/stop light function. 3 white LED's are used for license plate illumination.

Included is a set of turn signal brackets that bolt to the mount, but these are designed for a smaller LED type signal with a mounting stud of just 8mm. If you think this might be a problem, look at the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!

NOTE: LED's must be installed on a 12 V DC system!

The stock tail light, blinker and license plate bracket is rather large and cumbersome, to put it politely. The B&B Off Road Engineering unit is simple and tidy and gives you a LED tail and brake light unit, a LED license plate light and turn signal mounts as well.

Installation is easy - remove the stock unit and bolt the new unit in the same location. Off with the old and on with the new in minutes. All necessary hardware included.

The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail / stop light function. 3 white LED's are used for license plate illumination.

Included is a set of turn signal brackets that bolt to the mount. These are designed for a smaller LED type signal with a 8mm mounting stud. Or consider the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!

Sharpen Your Yamaha WR250R’s Look with B&B Off Road’s Tail Tidy

Give your Yamaha WR250R (2008-2021) a shot of attitude with B&B Off Road’s premium tail tidy! This innovative replacement ditches the bulky stock fender for a sleek and stylish design that elevates your bike’s aesthetics without compromising functionality.

Clean Lines, Easy Installation:

This tail tidy boasts a streamlined design that sheds unnecessary weight and bulk, instantly transforming your WR250R’s rear end. The straightforward installation utilizes existing mounting points for a hassle-free experience – get ready to hit the road (or trail) in no time.

Choose Your Finish:

Personalise your tail tidy to match your WR250R’s personality. Opt for a gleaming polished finish for a bold statement, or choose the classic black PPA-Gloss for a refined look. The brand new, low-lustre textured black powder coat (PC) offers a stealthy aesthetic for a more aggressive stance.

Unleash Your WR250R’s Potential:

This tail tidy doesn’t just enhance your bike’s visuals. The reduced weight contributes to improved performance, letting your WR250R handle even better. With a cleaner and more streamlined rear end, your adventure awaits in style.

Upgrade your Yamaha WR250R today! Order your B&B Off Road Tail Tidy and experience the perfect blend of functionality and sharp design.

Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.

Also works with Edge-2 Circuit Board Upgrade.

The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail/stop light function. 3 white LED's are used for license plate illumination.

Included is a set of turn signal brackets that bolt to the mount. These are designed for a small signal with a 8mm mounting stud. Or consider the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!

Lose that ugly stock taillight and license plate bracket and install this tidy one from ProCycle. We designed this unit and have it manufactured here in Oregon. Kit includes a LED taillight / brake light unit as well as compact turn signals. We also include splice connectors and split tubing, everything you need for this installation.

There is also an option to include matching front turn signals with side mount brackets that allow you to replace the clunky front signals with the same style as the rear in this kit.

Remove the bulky stock number plate holder with our slim design- comes with LED number plate light.

• Quick and easy install
• Mounting hardware supplied
• Comes with clear LED tail, brake & number plate light
• No mods required for installation
• Available in polished or black PPA coating.
• Pre drilled to suit Australian licence plate

*Please Note:  Brake light does not come with necessary/factory connectors. Some cutting, crimping, soldering of wires may be required for connection.

Yoshimura has always been synonymous with quality craftsmanship, precision fitment, and impeccable quality. The Fender Eliminator Kits are no exception, and they are sure to give your motorcycle the sleek race look that every rider craves

Features:

• Precision laser-cut stainless steel bracket tucks discreetly under the tail section of the motorcycle
• Black anodized CNC machined light housing with laser-etched Yoshimura logo
• Light housing contains four bright LED lights
• Black anodized aluminum license plate frame with silk screened Yoshimura logo
• Stainless steel hardware included
• Compatible with aftermarket turn signals when combined with YOSHIMURA TURN SIGNAL BRACKET (turn signals not included)

Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.

Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.

Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.

There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.
Hybrid - You can setup the kit to use your factory signals if you don't want to use the integrated turn signals.
You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.

• Plug and Play
• 7 Different Programmable Turn Signal Patterns (for demo video click here)
• Safety Brake pulsing built in (Can Enable or Disable)
• Integrated Turn Signals or you can keep your Stock Turn Signals installed.
• Super bright LED's; For excellent brightness, even in direct sunlight
• License Plate Light built in
• Includes removable License Plate Bracket (fits the common USA license plates, slotted for maximum plate compatibility)
• Includes Mounting Hardware
• Block-off plates for blocking off rear factory turn signal mount holes are included.
• Saves about 2 lbs over the factory tail light setup
• Built in the USA

We recommend the Fixed Rate Flasher unit with this kit. When you install aftermarket signals it changes the load on a factory signal system, when the load changes the stock flasher relay will "hyper flash" or blink at about twice the rate it normally does, this occurs even on a factory LED system such as the CRF450L.

OEM Fit for CRF450L rear tail light + turn signal connectors.

Pins pre-installed and pre-crimped with wire for easy install.

Set Includes: Connectors for left and right turn signal and tail light.

This kit is specifically for attaching After-Market tail light and turn signals.

Yoshimura has always been synonymous with quality craftsmanship, precision fitment, and impeccable quality. The Fender Eliminator Kits are no exception, and they are sure to give your motorcycle the sleek race look that every rider craves

Features:

• Precision laser-cut stainless steel bracket tucks discreetly under the tail section of the motorcycle
• Black anodized CNC machined light housing with laser-etched Yoshimura logo
• Light housing contains four bright LED lights
• Black anodized aluminum license plate frame with silk screened Yoshimura logo
• Stainless steel hardware included
• Compatible with aftermarket turn signals when combined with Universal turn signal bracket kit (sold separate)

Their is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.

You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.

• Plug and Play
• 7 Different Programmable Turn Signal Patterns (for demo video click here)
• Safety Brake pulsing built in (Can Enable or Disable)
• Superbright LED's; For excellent brightness, even in direct sunlight
• License Plate Light built in
• License Plate Bracket fits the common USA license plates, sloted for maximum plate compatibility.
• Includes Mounting Hardware
• Saves about 2 lbs over the factory tail light setup
• Made In the USA

We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.

This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.

This is a simple three piece kit you can install in minutes that cleans up the stock DR rear-end. We use the 250 taillight that fits perfectly into the pocket of the stock taillight on the DR650 fender. It is smaller, looks great and is out of harms way more than the stock unit. It is a total 'plug-n-play' as the wire pigtail plugs right into the DR650 harness just like stock. Then we use a small LED light to keep you legal and illuminate your license plate, which gets mounted to our custom stainless steel bracket, eliminating the stock ugly plastic mount.

Kit includes:

• Stainless Steel License Plate Bracket
• 250 Taillight/Brake Light Lens
• LED License Plate Light (shown below)

These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.

These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.

These turn signal relocation brackets from Yoshimura provide an easy way to move the stock turn signal lights or install aftermarket turn signals.

Combines with the Yoshimura fender elimination kit

• High Temperature UV Resistant Plastic
• 8mm Hole for Mounting Aftermarket Turn signals or Bolt with Block-off ability
• Stainless steel hardware included
• Sold in pairs (two mounting plates per set [for one left and one right side])
• You need to order TWO kits if doing the Front AND Rear of motorcycle

Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on 12-24 volt DC circuits.

Taillight & brake light. Attaches to the top side of enduro style (XR, KDX, etc) rear fenders. Dimensions: 2 3/8" x 4 3/4" x 1 3/4" tall. This light is a popular replacement for the gigantic stock XR650L taillight. Functions as taillight and brake light. Fits perfectly into the taillight pocket on the XR650L. Please note that this no longer has a window for a license plate light.

Taillight, brake light, & license plate light. Attaches to the top side of enduro style (XR, KDX, etc) rear fenders. Dimensions: 2 3/4" x 4 3/4" x 2 1/2" tall. Wiring instructions included.

This LED taillight replaces the factory taillight in Honda CRF450X and CRF250X rear fenders. Features a taillight and a brake light for a clean looking dual sport conversion. Wiring instructions included.

Taillight, brake light, & license plate holder (no plate light). Attaches to the underside of MX style rear fenders. Small and good looking!

Taillight and brake light Attaches to the top of the rear fender. Dimensions: 3 1/2" wide x 2" long x 3/4" tall. D.O.T. approved.

LED powered taillight, brake light, license plate light & license plate mount. Attaches to the underside of MX style rear fenders.

Make the Edge-2 Circuit Board installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. You will need a crimp tool or set of needle nose pliers to crimp connectors on.

If your taillight unit was damaged with your rear fender, we offer a brand new OEM unit.

Standard 1157 bulb holder socket for dual filament bulbs.

• Clear bulb
• 6 Ultra Bright, LED chips for maximum illumination
• Low heat. Won't melt lens
• 12V
• Low voltage draw
• High shock and vibration resistance

Make the installation as easy as possible with this Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight Circuit Board Upgrade making the connection simple. Stock plug will go right into this unit and off you go. You will need a crimp tool or set of needle nose pliers to crimp connectors on.

Make the Edge-2 Circuit Board installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. You will need a crimp tool or set of needle nose pliers to crimp connectors on.

The 250 taillight & brake light fits perfectly into the pocket from the stock DR650 taillight on the rear fender. Smaller and much better looking than the original.

Totally 'plug-n-play', includes a standard bulb installed or purchase an LED replacement, sold separate, for even brighter braking. The wire pigtail plugs directly into the DR650 harness just like stock.

  Does not fit with the ProCycle Fender

This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.

Features:

• Independently programmable flash speed, flash duration, and pre-delay
• Works for LED or Standard Bulb Tail Lights
• All Solid State design
• Meets or exceeds OEM load rating specifications
• Over 1000 possible flash pattern combinations
• Simple programming setup with your brake lever
• Extremely compact unit size; 20mm x 20mm x 12mm

This replacement lens has a clear panel on the bottom to illuminate your license plate. 

Allows you to bolt your license plate directly to the rear fender. 

Does not fit Australian DR650.

Taillight, brakelight, turnsignals, license plate light & license plate mount. Taillight is DOT approved, turn signals are not. Attaches to the underside of MX Style rear fenders. Turnsignals are embedded in the taillight housing. Wiring instructions included.
*Flushmount signals may require resistors to flash correctly

This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.

Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.

This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.

You may have noticed after adding aftermarket turn signals (especially LED units) that your blink rate has significantly increased. OEM flashers are designed for standard bulbs which draw a few watts each, much more than typical aftermarket bulbs or LED signals. This device is an effective alternative to using load resistors because it consumes considerably less watts, consumes less space, and does not generate excessive heat.

The plug is exactly the same as the OEM unit making swap outs a cinch. No wiring changes, cutting and adding connectors. Just plug it in and you will have a steady flash at the DOT OEM rate regardless of what signal bulbs you use. It is an all solid state design and will blink correctly with loads all the way down to 0.1W / 0.01A.

  Not for any DRZ400 or Royal Enfield Himalayan

Triangle/Teardrop style signals with LEDs. Mounts on any flat surface to keep out of the way of brush, branches, and your exhaust system. Requires LED flasher or LED turn signal resistors to flash properly. 

• Fits on the fender with screws for secure installation
• Rubber mount base fits even curved surfaces
• Terminals and bolts are included for installation
• Comes in pairs
• Works on 12V AC/DC

Works on AC and DC lighting systems

  Not compatible with any DRZ400

These Sequential Turn Signals are available in a 2 pack or 4 pack short stem with 7 LEDs.

Matte Black, plastic body with smoke lens and 8mm mount bolt.

Specifications

• E-marked.
• Short Stem: 75mm x 15mm

Eight ultra-bright amber LED lights in a sleek design. Flexible stem helps absorb the occasional hit. Available in 2 pack or 4 pack

Recommended to use resistor for proper turn signal flash rate.

Specifications

• Comes with mounting hardware.
• Measures 4" long with base and 1" wide at the lights.

When upgrading your Suzuki DR650 with LED turn signals, it's required to install a diode module to prevent all of the signals from blinking at once regardless of left or right signal activation. Some riders choose to splice and solder their own solution, but we like things plug and play. That means all you have to do is plug in the TST kit and you're done! There's no need to cut or splice your OEM wiring harness or break out the soldering iron and electrical tape.

• Plug and play installation - meaning no cutting, splicing, or soldering
• Eliminates issue of all signals blinking when activating only one side of turn signals
• Enables power to flow in single direction from LED turn signals to the dash indicator
• Does not fix hyperflash (LED turn signals flashing faster than OEM specified rate)
• (1) TST Plug and Play Diode Module
• 1 Year Warranty 

If you just installed aftermarket LED turn signals or an LED integrated tail light and your turn signals are flashing way too fast, or perhaps simply staying on completely, you're at the right place to find the solution! The TST Gen2-SK LED Flasher Relay fixes what we call "hyperflash". It slows the flash rate down to a pre-set 85 cycles per minute but can be sped up or slowed down using the adjustment dial located within the unit so you can get the exact speed you are looking for. The plug-and-play installation means that you don't need to splice in any load balancing resistors that generate unnecessary heat and require splicing into your stock wires. Simply remove the stock relay and install your new TST relay and your wiring job is done. It's that simple!

• Slows turn signal flash rate down to an adjustable 85 cycles per minute when turn signals are experiencing hyperflash or stay on continuously
• Adjustable turn signal flash rate enables you to speed up or slow down the flash rate to fit your preference
• Plug and play installation meaning no cutting, splicing, or soldering
• Replaces the stock relay and fits like OEM
• No need for cumbersome and heat-generating load balancing resistors
• Flexible relay housing enables easy access to the flash rate adjustment dial inside of the relay unit

Please make sure your bike uses a 2-pin relay for the signaling system. If your bike has hazard lights it may need the 4-pin relay. Please also note the pin configuration and make sure it matches what is on your bike. It is very important to verify fitment before making your purchase.

This relay will fix your flash rate problem caused by aftermarket signal lights and/or integrated tail light. If your signal lights flash too fast or do not flash, this part is your solution! Plug and play - easy installation.

Only ONE relay is needed per motorcycle.

Features

• Slows signaling flash rate back to the normal rate when your bike goes into hyperflash state (or your signals stay on constantly)
• Plug and play installation: simply replaces the relay already on your bike
• Fits like OEM

This component works with the following signal configurations:

1. All stock
2. Stock taillight, aftermarket signals
3. Integrated taillight, stock signals
4. Integrated taillight, aftermarket signals.

Mounts to existing signal brackets to move the front turn signals up and forward to clear the bigger 5.3 & 6.6 gallon Acerbis tanks.

Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.

White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.

Dazzling bright Amber blinker functions. 

All in a spring-loaded stock to prevent damage from a tip over, crash or impact with brush, trees etc. They will bend 360 degrees, but are stiff, durable and nearly unbreakable.

Yamaha T7 Specific plug and play kit using factory connectors, flasher and block off plates included.

2024 T7 setups coming soon