Lighting

A nice place to mount auxiliary lights on your KLX where they will be high and easy to reach for adjustment but still tight to the cowlings. They will not interfere with controls, body work or the fuel tank.

Constructed of 1/8" stainless steel they are intended for LED lamps in the 2" range, but with a slight slotting of the mounting holes, will work great with 3" lights as well. Includes longer bolts to for the upper triple clamp mounts.

Now available in the original version or the Ultra version. The original uses the front two emitters for low beam and then switches to the rear two emitters for high beam. The Ultra uses the front two emitters for low beam and then runs all 4 emitters on high beam at a reduced wattage. Wattage is 38 watts on low and 38 watts on high.

This bulb uses 4 Cree XHP 50 emitters, capable of more than 2500 lumens each. At 5000 lumens on each function, this is the brightest Cyclops H4 bulb.

• All metal construction for bases and collars
• Better thermal efficiency 
• Better beam pattern distinction between high and low beams
• 5600k
• 38 watts 
• Removable metal base plate for easy install.
• Screw on connectors at driver
• Standard H4 connector
• High/Low Beams

*UNIVERSAL PART, PLEASE CHECK YOUR APPLICATION FOR FITMENT

This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.

The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail / stop light function. 3 white LED's are used for license plate illumination.

Included is a set of turn signal brackets that bolt to the mount. These are designed for a smaller LED type signal with a 8mm mounting stud. Or consider the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!

Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.

Make the installation as easy as possible with this Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight Circuit Board Upgrade making the connection simple. Stock plug will go right into this unit and off you go. You will need a crimp tool or set of needle nose pliers to crimp connectors on.

Standard 1157 bulb holder socket for dual filament bulbs.

• Clear bulb
• 6 Ultra Bright, LED chips for maximum illumination
• Low heat. Won't melt lens
• 12V
• Low voltage draw
• High shock and vibration resistance

There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.

You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.

• Plug and Play
• 7 Different Programmable Turn Signal Patterns
• Safety Brake pulsing built in (Can Enable or Disable)
• Superbright LED's; For excellent brightness, even in direct sunlight
• License Plate Light built in
• License Plate Bracket fits the common USA license plates, sloted for maximum plate compatibility.
• Includes Mounting Hardware
• Saves about 2 lbs over the factory tail light setup
• Made In the USA

We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.

This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.

Does not fit 2024-2025 Models.

This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.

Features:

• Independently programmable flash speed, flash duration, and pre-delay
• Works for LED or Standard Bulb Tail Lights
• All Solid State design
• Meets or exceeds OEM load rating specifications
• Over 1000 possible flash pattern combinations
• Simple programming setup with your brake lever
• Extremely compact unit size; 20mm x 20mm x 12mm

The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.

You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.

Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.

There are many options and configurations using this electronic tool.

No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.