Lighting

This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.

There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.

You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.

• Plug and Play
• 7 Different Programmable Turn Signal Patterns
• Safety Brake pulsing built in (Can Enable or Disable)
• Superbright LED's; For excellent brightness, even in direct sunlight
• License Plate Light built in
• License Plate Bracket fits the common USA license plates, sloted for maximum plate compatibility.
• Includes Mounting Hardware
• Saves about 2 lbs over the factory tail light setup
• Made In the USA

We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.

This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.

Does not fit 2024-2025 Models.

Standard 1157 bulb holder socket for dual filament bulbs.

• Clear bulb
• 6 Ultra Bright, LED chips for maximum illumination
• Low heat. Won't melt lens
• 12V
• Low voltage draw
• High shock and vibration resistance

This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.

Features:

• Independently programmable flash speed, flash duration, and pre-delay
• Works for LED or Standard Bulb Tail Lights
• All Solid State design
• Meets or exceeds OEM load rating specifications
• Over 1000 possible flash pattern combinations
• Simple programming setup with your brake lever
• Extremely compact unit size; 20mm x 20mm x 12mm

Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.

White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.

Dazzling bright Amber blinker functions. 

All in a spring-loaded stock to prevent damage from a tip over, crash or impact with brush, trees etc. They will bend 360 degrees, but are stiff, durable and nearly unbreakable.

Kawasaki KLR650 Gen 3 / KLX300 Specific plug and play kit using factory connectors, flasher and block off plates.

This relay will fix your flash rate problem caused by aftermarket signal lights and/or integrated tail light. If your signal lights flash too fast or do not flash, this part is your solution! Plug and play - easy installation.

Only ONE relay is needed per motorcycle regardless of front and rear signal set-up.

• Slows signaling flash rate back to the normal rate when your bike goes into hyperflash state (or your signals stay on constantly)
• Adjustable functionality to speed up or slow down flash rate to your preference
• Plug and play installation: simply replaces the relay already on your bike
• Fits like OEM
• Relay housing is flexible so that you can access the adjustment dial inside the unit

This component works with the following signal configurations:

1. All stock
2. Stock taillight, aftermarket signals
3. Integrated taillight, stock signals
4. Integrated taillight, aftermarket signals.

The relay comes preset to 85 cycles per minute. You can alter the flash rate to make it faster or slower. If you slip off the grey cover you can access an adjuster that will enable you to change the flash rate to your liking.

Please make sure your bike uses a 2-pin relay for the signaling system. If your bike has hazard lights it may need the 4-pin relay. Please also note the pin configuration and make sure it matches what is on your bike. It is very important to verify fitment before making your purchase.