Controls

CNC machined from 6061 Aluminum by the crew at Warp 9. This upper triple clamp will help to get the bars out of your lap on the XR650L. It allows for six different bar positions (three mount positions and reversible offset mounts). Uses the stock key switch and works with the handlebar lock. Speedometer and indicators all use mounting positions as well.

This clamp comes with 1-1/8" handlebar mounts.

Introducing the Zeta solid bushings to replace your worn out rubber bushings. We have tested these bushings on our own bike and we love them. No more sloppy handle bars. Plus, they add a little bling factor to your bike! Simply unbolt your bar mounts and swap the rubber bushings with these anodized billet bushings for a more stable handlebar feel.

Features:

• Solid cones for rubber bar mounted stock triple top clamps
• Provides direct control and prevents bar twist when falling down
• Comes in a set of 4 solid cones
• Made of A7009-T6 aluminum

• 4.75" wide,
• Raises handlebars 2 inches and allows fore/aft position adjustment
• Provides dual pivot points for optimal bar positioning
• One piece design is made from solid aluminum for superior strength
• Available for 7/8" - 7/8" or 7/8" - 1 1/8" bars

Requires 7/8" factory bar clamps on bike

This unique design from Rox allows you to move your bars either closer (1" up and back) or further away (1" forward and 1-1/4" up) depending on rider preference. These risers have an oblong mounting hole so that they will fit virtually any triple clamp with 8mm bolts. A set of reducers lock into the risers ensuring no slippage whether you have a 7/8" or 1-1/8" bars.

Because these are offset there may be limited clearance between the gas tank and the risers when the bars are fully turned on some models, mainly when mounted to move the bars closer.

Handlebar mounts that replace your stock clamps.

These raise your handlebars 1 inch.

Available in 7/8" for standard handlebars allow installation of your choice of 7/8" off road handlebars.

Handlebar mounts that replace your stock clamps.

These raise your handlebars 1 inch.

Choose 7/8" for standard handlebars or 1-1/8" to allow installation of your choice of oversize/ tapered handlebars.

Mount these polished billet aluminum spacers under your handlebar clamps to raise your handlebars 1 inch. High quality longer bolts are included.

• Adapt 7/8" bar mounts to accept oversized 1-1/8" handlebars
• An economical alternative to replacing expensive top triple clamps
• Include mounting bolts.

• CNC-machined from aerospace quality 7075-T6 aluminum alloy
• Handlebar clamps included
• Adjustable bar clamp mounting position
• Easy to install; pre-pressed Pivot Works lower bearing included
• Developed in collaboration with top US MX/SX and MXGP teams
• Torque settings etched on the clamps
• Greater rigidity
• Anodized finish

• Fit models with a 1 1/8" stem clamp and a 1 1/8" handlebar
• Handlebar clamps can be pivoted to desired fore and aft location to achieve ideal riding position
• Engineered and tested for maximum strength and durability
• CNC-machined from billet 6061-T6 aluminum, then anodized for long-lasting good looks
• 2" center to center rise above stock position

These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.

These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.

Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).

CNC machined from 6061 Aluminum by the crew at Warp 9. This upper triple clamp will help to get the bars out of your lap on the XR650L. It allows for six different bar positions (three mount positions and reversible offset mounts). Uses the stock key switch and works with the handlebar lock. Speedometer and indicators all use stock mounting positions as well.

This clamp comes with 1-1/8" bar mounts that work perfectly with the tapered handlebars included. Then there is a new set of ProGrip 714 Rally Grips.

This bar kit will raise your hands 5.5" up from the factory riding position. If you are over 6 feet tall, this is the kit for you! It allows for a more natural riding position, no more bent neck and being hunched over the bars. You will be able to ride comfortably and more aggressively by installing this kit.

The ProTaper bars are taller and tapered from 1 1/8" to 7/8" and the braided stainless steel brake line will be a serious improvement to your braking ability. Braking becomes more responsive and firmer while adding a stylish look to your TW200.

Everything you need is in this kit to properly raise your bars:

• ProTaper ADV High handlebar
• PowerMadd 2" bar riser
• Harness extensions
• Longer braided steel brake line
• Longer clutch cable

Here is a complete kit to install oversized tapered 1-1/8" handlebars on your DR650. Warp9 handlebar clamps bolt to your stock triple clamp adding an additional 1" to the height.

Alloy oversize bars offer more durability and eliminate the crossbar which opens up your dash area for more goodies. Black in color.

Silver in color

Upgrade your bike with a tapered 1-1/8" bar. Constructed of Aircraft grade 7065 T-6 aluminum that tapers to a standard 7/8" to accept stock controls.

• Lighter and stronger than regular bars
• No-crossbrace allows flex to reduce shock and rider fatigue
• Etched alignment marks for fast and accurate positioning
• Flex Series pad included

Comfortable Oversize (or Fat Bar) Handlebars.

• Black in color. 
• Made from 5mm, proprietary, 2000 series T6 aluminum alloy for superior tensile and yield strength.
• Lighter and stronger than regular bars
• No-crossbrace allows flex to reduce shock and rider fatigue
• Oversize 1-1/8" diameter base reduces to 7/8" to allow standard-size controls/grips
• Etched alignment marks for fast and accurate positioning
• Bar pad included
• Works with stock controls and cables.

For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8  adapter (sold separate).

This kit is for those of you looking for a bit more arm room and a better platform for your feet in the TW cockpit. Included are ProCycle Wide Foot Pegs and our oversize bars with 30mm risers.

• ProCycle Wide Pegs are wider MX style pegs that are much more comfortable when standing.
• These are not only taller bars, but 1-1/8" at the clamp area for additional strength. They taper down to 7/8" on the ends so all the stock controls fit. Black in color.
• 30mm Moose risers that raise the handlebar 30mm.

Kit does not include new throttle tube. If you have 2001 or newer TW200 and would like a new billet aluminum throttle tube, please select the addon box to receive one with your order.

This kit is for those of you looking for a bit more leg and arm room in the DR cockpit. Included are ProCycle Low Foot Pegs and our oversize bars.

• ProCycle Low Pegs will drop your pegs by 1-3/4" and include wider MX style pegs that are much more comfortable when standing.
• These are not only taller bars, but 1-1/8" at the clamp area for additional strength. They taper down to 7/8" on the ends so all the stock controls fit. Black in color.
• 1 1/8" Warp 9 clamps that raise the handlebar 1".
• A new billet aluminum throttle tube is included.

Direct replacement cables for your T-Dub. OEM or high-quality replacements will keep you on the road or trail. Pay attention to the model year for correct fitment, then select the cable type: Throttle, Clutch or Speedo, they're all here.

Factory Yamaha replacement clutch cable.

A quality replacement speedometer cable

A quality set of replacement throttle cables from Motion Pro.

A high quality replacement clutch cable.

Throttle cable routing on the XR650L gives you very little extra slack for raising the bars or adjusting them towards the rider. We now offer throttle cables that are 3" longer than stock allowing you to customize the bar position to your riding style.

These quality cables are made by Motion Pro.

OEM throttle cable set for the CRF250L

*generic image, actual cables may look different.

Throttle, Clutch or Speedo cables.

Designed to seal completely around the cable housing and stop all those messy leaks. With the unit closed and sealed around the cable, your cable gets better lubrication and you waste less lubricant.

• Works on most cables with a 4mm - 8mm O.D. housing.

Keep your cables lubed up and working freely, with Motion Pro's Cable Luber. This tool is used to inject lubricant into any cable housing. Clamps over housing and cable allowing an aerosol can with nozzle to be connected. Once the lubrication solution runs out the far end, the cable is lubricated.

Genuine Yamaha replacement throttle cables.

A quality replacement speedometer cable.

A quality set of replacement throttle cables from Motion Pro.

OEM throttle cable.

Genuine OEM replacement choke cable.

A quality replacement speedometer cable from Motion Pro.

• Black vinyl coil-wound housing
• Meets or exceeds OEM quality
• Inner nylon sleeve for longer life and smooth operation

Spare replacement throttle cables for your TM40 carburetor conversion. Fits the stock throttle housing.

These are premium low-friction cables. 

A quality set of replacement throttle cables.

A quality OEM replacement clutch cable.

High quality replacement cables from Motion Pro.

A quality set of replacement throttle cables from Motion Pro

Custom made push/pull cable set for the Honda XR650L.

These are for use with the stock throttle assembly, when mounting a Mikuni push/pull pumper carb, or Keihin FCR series carburetor.

Available as +3" and +6" over stock length, with stock style throttle side fittings.

Sold in a set as shown.

• Manufactured to exact measurements to meet or exceed oem specification
• Tempered steel wire housing with an inner nylon sleeve for long life & smooth operation

• Handy, compact kit for on-the-go emergency throttle, clutch and brake cable repairs
• Includes 2 different diameter 6.5 long inner cables and an assortment of cable ends

• Manufactured to exact measurements to meet or exceed oem specification
• Tempered steel wire housing with an inner nylon sleeve for long life & smooth operation
• Cables are individually packed in a poly sleeve with color coded header cards

Quality replacement clutch cable.

• Nylon-lined housings and precise OEM component dimensions

• Black PVC outer jacket for maximum flexibility and durability
• Steel inner casing is tightly coiled for low compression ratios
• A pre-lubricated nylon inner sleeve guarantees smooth operation and long life
• All wire ends are bird-caged prior to terminal casting for superior pull-out resistance
• EPDM molded rubber components for high UV resistance and long life
• Injected-molded components are manufactured from high-strength POM material

This listing is for either one throttle cable or one clutch cable, not both.

The plastic fitting that secures the stock choke cable to the carburetor is delicate and easily broken. A broken fitting can cause hard to solve idling and running problems.

CNC machined from billet aluminum and anodized black or blue. If you want to retain your handlebar mounted choke this may be the solution.

  These no longer fit the new version of the ProCycle Remote Choke Cable. Will not work with the long or short reach choke knobs.

This is the evolution of taking the proven GPRV1 steering damper and locating it under the handlebars. Mounting the damper unit under the bars allows for addition room on the top cross-bar or bar mounts.

This GPR setup is a good choice for the weekend warrior to the race professional that would like to raise the handlebar height. Perfect for desert and off-road GPs.

The GPR V5 stabilizer is designed to be "tucked" away under the bars and is still easily adjustable without raising the handle bars too high.

• Kit includes damper, bolt on post mount, below the bar mounting system, and complete instructions.
• Only raises bars about 1/2".

• Will only work with Fat Bar style (1 1/8" clamp area) handlebars and stock triple clamp.

Ease the pressure on your wrist during those long highway trips.

ProCycle has developed this unique kit to work with your OEM bars and controls. Just flip the thumb lever down to apply enough friction to hold the throttle in place.

Customize the power characteristics of your bike by simply adding an altered ration cam. The Control cam allows smoother more controlled throttle while the Quick cam lets you put the power to the ground quickly.

Throttle Lock Kit Includes:

• Billet aluminum throttle tube with standard cam
• Vista Cruise Throttle Lock
• All mounting hardware
• Tension adjustment tool

The Apollo Heated Grips are designed with an integrated adjustable thumb switch, which allows them to easily fit on any kind of motorcycles on the market. The integrated thumb switch gives control to the rider to adjust the temperature level while keeping hands on the bar for a safer ride.

Its wide temperature setting range will keep the rider comfortable under the cold riding conditions.

The 5 color LED display will enhance the visual look of the heated grips and will allow the rider to quickly know at which heat level the grips are set.

This system will also detect if the battery voltage is too low and will automatically shut down the heated grips in order to make sure the rider have enough power to start the engine or use the motorcycle.

Specifications:

• Integrated thumb switch designed for easy installation and control.
• “Plug & Play” wiring connections to shorten the installation time.
• Wide temperature settings for various weather conditions.
• Low Battery Warning protection to ensure the motorcycle has enough power to start.
• 5 color LED Indicators for the rider to quickly know in which heat level the grips are set.

• Machined and knurled 6061 billet aluminum. Actual color may vary
• Removable end cap for easy handguard installation
• Works with standard housing

These new heated devices are for the user that does not want to commit to changing their grips but still wants to maintain the comfort of heated grips. The fitment is intended to fit all sorts of handlebar sizes. They can be installed and removed in a matter of seconds and kept in any sport bag when not in use.

Features:

• Universal fit to be clipped on any handlebar sizes
• Rubber material that is resistant to outdoor conditions and high temperatures
• Thin and flexible silicone wires make them easy to install

Protect your thumbs from blisters caused by riding on the inside of your grips.

Sold in Pairs.

• Machined and knurled 6061 billet aluminum. Actual color may vary
• Removable end cap for easy hand guard installation
• Works with standard housing

Ease the pressure on your wrist during those long highway drones out to where the fun begins. ProCycle has developed this kit that includes a Vista-Cruise throttle lock, a specially modified alloy throttle tube and an anchor plate that attaches to your throttle housing. Just flip the thumb lever down to apply enough friction to hold the throttle in place. Use the supplied longer screw to attach the anchor plate to your lower throttle housing bolt hole. Also included is a tension adjustment tool that you can keep on your key ring. Keep the applied tension lightly adjusted so it's easy to roll the throttle off.

Fits bikes with dual cable throttle housings.

Opens your throttle 15% faster. No more 'double handfuls' to get it wide open. Removable end cap for bikes with hand guards.

This little jewel reduces hand fatigue and cramping on long rides or daily commutes. The Crampbuster is not a throttle locking unit but, rather a simple clip-on device which allows you to relax your grip while riding.

The Go Cruise cruise control mounts over the throttle grip and rests on the brake lever to hold your throttle open, allowing you to stretch and rest your hand on long rides. Installs and removes in seconds with no tools. You can roll off the throttle manually to disengage the Go Cruise.

• Replace OEM throttle sleeves
• Heavier duty and exceed the quality and durability of OEM sleeves
• Will not scar bars like aluminum sleeves
• Nylon fabric composite material
• Molded ridges to help secure grips
• One-piece tube and reel design
• Actual color may vary

ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology.  Try the grip with the technical advantage of three dedicated rubber compounds.

The difference between the original Pillow Top and the Pillow Top Lite is the overall diameter of the grip surface. The Lite offers a smaller diameter so the grips don't feel as large reducing fatigue in your hands while riding.

• Vibrasonix pillow top reduces vibration and cushions impact. 
• Inner core compound perfects the bonding interface with bars. 
• Anti-Rip Tip™ uses denser compound to increase life of grip. 
• Designed to self-clean and shed mud away from outer surface. 
• Tacky gel-like surface compound is perfect for the trail and MX.

Highly efficient design delivers warmth faster than traditional heated grips.

Choose from the standard five level push button temperature controller, or the LCD display controller which shows the selected heat level and available battery voltage.

These grips feature a thicker design that dampens vibration. The soft shoulder allows ease of movement. Three wire-tie grooves are molded into the grip to make securing them a breeze. We think they are great!

Suzuki makes it almost impossible to replace your stock grips. It's much easier with a new throttle tube. 

• Machined and knurled 6061 billet aluminum.  Actual color may vary.
• Removable end cap allows handguard installation without the hacksaw
• Lightweight, removable cams are compatible with G2 throttle systems

ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology.  Try the grip with the technical advantage of three dedicated rubber compounds.

• Vibrasonix pillow top reduces vibration and cushions impact. 
• Inner core compound perfects the bonding interface with bars. 
• Anti-Rip Tip™ uses denser compound to increase life of grip. 
• Designed to self-clean and shed mud away from outer surface. 
• Tacky gel-like surface compound is perfect for the trail and MX.

Each pattern is available in three advanced synthetic rubber compounds. This means you can have the optimum combination of strength, tackiness and shock absorption to suit every riding condition and individual style. Soft grip is extremely soft, giving you a very comfortable ride, great feel and reduces the chance of blisters; however, because the grip is so soft, it wears quickly. Medium is a compromise between firm and soft. Firm grip has the same feel as a stock grip, it is very strong and has very good resistance to tearing and abrasion. Half Waffle has waffle pattern in finger area for traction and diamond pattern on palm side to reduce blisters. Full Waffle: designed after the CR Honda® grip.

• Feature the classic Vans waffle sole pattern with a subtle domed center section for improved ergonomics and vibration dampening
• 125mm in length
• Fit 7/8" bars
• Sold in pairs

These heated grips from Koso have been tested by us and we can say they will keep your hands warm and give you the grip you need in off road conditions, thanks to the full diamond grip design.

• Clamp-on grips do not need adhesive
• External temperature controller with 5 heat levels
• For use with twist throttle; includes interchangeable throttle cams
• Requires 35W and draws 2.5 amps per pair; low voltage shut off

• Ergonomically designed
• Medium-density Thermoplastic Rubber (TPR) compound provides excellent feedback and control, without sacrificing durability
• Full diamond pattern for an unparalleled feel in both wet and dry conditions
• Inner diameter optimized to keep grips secure in any conditions
• 115mm overall length; fit 7/8" bars and throttle sleeves

• The new 3rd generation Motion Pro Revolver variable rate throttle system is here!
• Innovative reel changing system lets you tailor the throttle rate to your preference and riding conditions
• 5 different reels provide perfect throttle response for any condition. Use smaller reels for slower throttle rate and larger reels for faster throttle rate. Included cam reel provides progressive throttle response preferred by some riders
• Slim REV3™ throttle housing allows more room for lever clearance and adjustment to throttle housing position
• Improved throttle stop provides greater strength and durability
• Snap together elbows makes it even easier to install and change reels
• Cable boot keeps dirt and dust out for reliable and smooth operation
• REV3™ off-road kits are compatible with the new Motion Pro DirtControl™ V2 Lock-On grips and ODI Lock-On grips
• Billet aluminum inline cable adjusters ease installation and adjustment
• Lower section of cables use 5 mm housing with PTFE liner for reduced friction, increased routing flexibility and lighter weight
• Upper section of cables use 6 mm housing to provide solid support of adjusters
• Simple to install and maintain
• Patented

Kit includes:

• REV3™ throttle assembly with throttle tube (REV3™ off-road kits include the unbreakable Titan Throttle Tube™)
• Motion Pro REV3™ black vinyl cables specifically designed for your bike
• REV3™ sportbike kits include Motion Pro RoadControl™ grips
• Four interchangeable round reels: 35 mm, 40 mm, 45 mm, 50 mm
• Progressive cam reel - Sportbike kits include road race profile cam reel (orange)

These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!

ProTaper's ADV handlebars give you a bar taller than most with extra space on the control portion of the bar. These bars provide an additional 20mm of space next to where your levers and throttle are located for your GPS, phone cradle, auxiliary switches, etc . They come in Adventure (which is taller than stock) and Adventure High (which is even taller).

These  are oversize bars, which means they are are 1 1/8", not the smaller 7/8" diameter. Therefore some bikes will require a adapter and there are several available to select from.

Using the same manufacturing techniques and materials as ProTaper’s industry-changing 1⅛" motocross handlebar, the EVO Adventure is specifically designed to provide adventure/touring riders with the increased comfort and control they need. With over 8" of straight section in the control areas, mounting vital components is made easier than ever. With its premium 7000 series aluminum alloy construction and computer-profiled four millimeter-thick wall design, the EVO Adventure Handlebar is up to 25% lighter and 45% stronger than competing handlebars.

• 1⅛" tubing at the clamping area
• Exclusive 4 mm-thick 7000 series aluminum alloy for superior tensile and yield strengths
• Optimum balance between fatigue life, impact strength, and impact-absorbing flex
• High-tech shot peened, stress-relieved, and anodized finish for unmatched durability
• Independent lab tests show that the EVO Handlebar leads the market in fatigue life
• Epoxy inner coating resists corrosion
• Chemically applied cut lines and alignment grid are scratch- and peel-resistant
• Plastic bar end plugs keep the elements out and provide a stronger base for grip ends
• Weighs only 1.55-1.7 lbs. (720-780 grams), depending on bend

The GPR v5 is the fifth generation steering damper.  Its compact and slim design allows for the damper to be mounted below the handlebars, out of harm's way, without raising the bars more than an inch.

V5-D Fat Bar kit – A Sub mount kit, mounts below the handlebars. Uses the low-profile GPR V5d dirt bike stabilizer in a cradle-style handlebar mount and bolts to the stock triple clamp. Will raise bar height about 1".

These kits include the GPR V5d dirt bike damper, handlebar mount, frame bracket and all mounting hardware.

Here is the little switch that mounts inside your brake or clutch lever perch and controls the brake light or clutch safety circuit. This switch often gets damaged in an unplanned dismount (aka: crash) or the plastic simply cracks from age. When this happens, you can find yourself chasing a short circuit that keeps blowing your fuse every time the brakes are applied. If this has happened to your TW, here's the fix!

  Competition levers by Moose Racing incorporate a cast aluminum lever with silicone grip inserts and anti-friction bronze bushings

• Levers are approximately 1" shorter than stock
• Sold as a set

  These levers will only fit the DIRT ONLY model! If you have a license plate, DO NOT ORDER!

Replacement shift lever with folding tip for use with OEM footpegs.

A set of replacement brake and clutch levers. Standard length.

These tips are for the Warp 9 Shift Levers only. 

These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours.

You can also order just a new pin hardware kit which comes with new pin and clip.

The Warp 9 shift lever is black anodized and the Warp 9 logo is laser etched into the finish. Comes with a black anodized knurled aluminum tip that folds and returns via a stainless-steel return spring. Includes the pinch bolt as well.

This bracket mounts between the frame and your right footpeg bracket (works with both stock and low mounts) and allows you to adjust the slop out of the stock system. Puts the pedal in the ultimate location for immediate brake activation and eliminates unwanted pedal motion. Kit includes plate, adjuster bolt and lock nut and instructions.

A stock replacement brake pedal for the DR650. Nothing fancy but sure gets the job done. Just order it up and get back on the trail. See our Brake Pedal Adjuster Bracket that allows you to adjust the position of your brake pedal to perfection.

Replacement shift lever from IMS with folding tip.

The MAGURA HYMEC hydraulic clutch system gives you an ease and smoothness of pull that cannot be equaled by a cable unit. No need to lube the cable, no more broken cables. The HYMEC is simply a fantastic hydraulic retrofit clutch system. You will be able to get away with applying a lot less pressure than with a standard cable clutch. Depending on riding style, this can make for huge benefits in terms of riding comfort and control. The master cylinder control naturally has reach adjustment.

The advantages of the MAGURA hydraulic clutch are many:

• Forged lever with improved lever ergonomics
• Filled and delivered ready to install
• Easy to install, detailed instructions included
• Less energy required
• Fine response
• Finely tuned metering capability
• No fluctuation in the pressure point
• Maintenance free
• First class workmanship-"Made in Germany"

MAGURA favors use of their 'MAGURA Blood' for its clutch systems. Mineral oil is non-toxic and not hygroscopic. Regular changes of the clutch fluid are not required.

Forged aluminum, black anodized arm and Knurled CNC aluminum shift tip.

Order up your new levers here! If you keep breaking levers, you might want to think about a set of handguards to protect them in case of a fall.

• Warp 9 Flex Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces
• Adjustable reach allows customization to the rider’s hand size
• Double hinge design allows lever to flex out of the way in most impact situations
• Pushrod or Bearing contact styles for smooth brake modulation
• Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal

• Warp 9 Flex Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces
• Adjustable reach allows customization to the rider’s hand size
• Double hinge design allows lever to flex out of the way in most impact situations
• Pushrod or Bearing contact styles for smooth brake modulation
• Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal

Order up your new levers here! If you keep breaking levers, you might want to think about a set of hand guards to protect them in case of a fall.

Replace your Bent or Broken Levers.

• Meets or exceeds OEM specifications
• Made from aircraft A-360 die cast aluminum

  TW200 fitment 1987-2000 year models with Drum Front Brake or 2001-2014 year models with Disc Front Brake.

Replace the soft stock lever with sturdy forged aluminum.

Folding tip prevents snagging.

Hardened splines won't slip or rotate.

OE style clutch or brake lever.

• Quality Aircraft grade A-360 aluminum for strength & durability
• Designed to exceed OEM specifications, built to resist breakage
• Durable hard coating
• Designed to fit OEM perch

Attach this over your brake lever and hand grip, squeeze the brake lever, pull the locking bar in and lock the black portion down. This creates a locked front brake, making parking safe and secure with about 5 seconds of effort.

To unlock the BrakeFix, you just lift the back of the black hooking portion to release it. This takes about 2 seconds. Perfect for use with Snapjack type stands or just parking on an incline.

A set of replacement brake and clutch levers. Standard length.

Please be sure and order the correct levers for your model year KLR.

Note: Gen 1 levers are black
Gen 2 levers are Silver

The Magura Hymec Hydraulic Clutch system. Simply remove the stock perch, lever and cable and bolt this in its place. This system replaces the stock cable with a small lightweight hydraulic system for improved clutch control, easier operating pressure, a constant pressure point and smoother actuation. Developed over many years and tested under the toughest conditions possible in the off-road motorcycle world.

You will have to bypass your clutch safety switch to use this unit.

Never hurts to have a bit of the Margura specific Blood Red hydraulic fluid as well.

Warp 9 has created a beautiful brake pedal machined from billet aluminum to an 8mm thick work of art. A stainless steel pin eliminates wear in the frame. This pedal has the ability to move the spring loaded brake tip 10mm either way from the center position. The arm is arched to provide clearance for riders who have the lowpeg + centerstand combination.

New from Twin Air, a forged aluminum KLR650 folding shift lever with your choice of Black, Blue, or Green tip. These are 3/4" longer than the stock lever which makes for easier shifting while standing, as well as for those with a larger boot size.

Replacement shift lever with folding tip.

The Warp 9 shift lever is 7075T6 CNC arm, the Warp 9 logo is laser etched into the finish. 

Includes a black folding aluminum tip and stainless spring and pivot pin for years of rust free use.

1" longer than stock

Do you have lowered foot pegs and can’t get your brake pedal adjusted low enough? 

The tip of this heavy duty JNS rear brake lever is 1.0” lower than the factory component and will get you back in the proper range of adjustment.

ONLY FITS 2012-CURRENT KLR650

Order up your new levers here! If you keep breaking levers, you might want to think about a set of hand guards to protect them in case of a fall.

Replacement shift lever from IMS with folding tip.