Off-road only version of the DR350
Sold in the US 1990-1999
Chain Size: | Front Sprocket: | Rear Sprocket: | Front Tire: | Rear Tire: | Spark Plug: |
520x110 |
14T ('90-'93, '97) 15T ('94-'99) |
47T ('90-'93, '97) 44T ('94-'99) |
80/100-21 | 110/100-18 |
DPR9EA-9 ('90-'93, '97) CR9EK ('94-'99) |
Tires
Motion Pro T-6 Combo Lever has a hex box wrench for your axle nut on one side and a perfectly contoured tire spoon on the other. Manaufactured from lightweight forged T-6 aluminum with a hard anodized finish. These beauties are just under 10 inches long and weigh only 3.5 oz. Available in a 12/13 combo unit and a 22, 24, 27 and 32mm hex ends.
These Rider's Wrenches by Fredette are combination wrenches that have three wrenches in one! A 2-stroke size spark plug wrench - a front axle and a rear axle wrench. Yep, all three in one unit.
Available in the combinations shown that will fit virtually all current dual-sport machines.
The MotoPressor is a compact pump unit that weighs only 1.3 pounds and fits in the palm of your hand! Measures 4"x3"x1.5" This makes it smaller and easier to carry with you.
It includes a 8 inch long inflation hose, with a a low air loss chuck. You also get an SAE power cord that attaches to your battery and stays there, along with alligator clips with SAE connector. The Pocket Pump has an 6.5 foot power cord. All of this packs into a heavy duty neoprene pouch.
MotoPressor will inflate a 150/70/ R18 tire from 0-31psi in under 4 minutes, and is capable of pumping up to 130psi. It also features a built-in cooling fan to keep the pump at optimum operating temperature, and a check valve to check the psi by attaching your tire gauge to this valve.
The Mini-Morph is actually a bicycle pump, but it is the best manual compact pump for adventure / dual-sport riding. It has a fold-out foot and handle and a 4 inch hose so you can set it on the ground to pump!
This thing is small enough to stow away in just about any bag and go unnoticed until you need it to fix a flat or add air after a long arduous ride.
A set of 6 threaded cartridges, good for 8-9 psi each.
CO² cartridges cannot be transported on an aircraft
Don't leave yourself stranded! The Moose Tire Inflator Kit gets you back on the road or trail quickly.
This kit has 3 cartridges, 4" inflator hose, and a zippered pouch that fits neatly into a tool bag or fender bag.
Uses threaded cartridges only, each cartridge produces 8-9 psi.
CO² cartridges cannot be transported on an aircraft
All that you need to repair and inflate your tire on the road or trail.
The padded nylon zippered carrying case holds three small, two medium and one large patch, buffer, .50 oz tube of rubber cement, five 4" rubber insert strips, insertion tool, reamer/rasp tool, three threaded cartridges, and a 4" threaded inflator hose.
Fits neatly into your tool bag or fender pack.
CO² cartridges cannot be transported on an aircraft
Changing tubes or tires without the right tools can be a real chore. Don't fight your snug beads any longer, use this 27" long tool that opens to 7-3/4" to provide the leverage you need to easily break your tire bead. Constructed from heavy-duty steel with comfortable no-slip grips, this tool makes the job a snap.
No more fighting to keep the bead down while installing or repairing your off-road tires. The Bead Buddy holds the tire bead down in the drop center of the rim during tire changes making changes as easy as possible. Machined from tough 6000 series aluminum the Bead Buddy is light weight and compact enough for any tool pack. The Delrin securing thumb screw insures no scratches to your rims.
The Bead Buddy is NOT recommended for use with Bib Mousse tubes.
- Durable 6061 aluminum with blue anodized finish and laser engraved logo
- Used to push the tire bead down into the drop center of the rim on off-road wheels while using tire tools to change tires
- Hooks over spoke and pushes bead down on opposite side of tire from tire irons
- No more fighting to keep bead down while installing off-road tires
- Innovative multi-use tire tool set
- Breaks the bead on most street and off road motorcycle tires
- Integrated tire spoon for tire removal and installation
- Light weight and compact size is perfect for tool packs
- Ergonomic handles with crossguard to keep hand from riding forward
- Forged 7075-T6 aluminum construction for strength and durability
- Black anodized finish
- Patent pending
Available in 9.5" aluminum (ideal for travel) and 16" forged steel (useful in a home shop/garage)
The Pro Fill Air Chuck from the people at Motion Pro is perfect for those tough to reach valve stems with its pivoting angled head. The design gives users extra hand clearance to avoid hot brake rotors or dirty chains. Billet manufactured from aluminum gives it a precise fit and function combined with light weight. It is finished off with a beautiful blue anodizing and then the Motion Pro logo is laser etched on forever. 1/4" NPT female inlet allows use with common air hose couplings and fittings.
A great addition to any tool box!
The MotoPressor Puncture Repair Tool combines the four tools essential for tubeless tire repair into a single tool.
With the motorcyclist in mind, they've designed a "4 in 1 multi-tool" that uses pre-vulcanized repair strings and packs into a sheath measuring a mere 130 x 68 x 50mm, that's small enough to fit in your pocket. The tool contains a pair of pliers, a rasp, an insertion tool and a sharp knife, which is all you'll need to fix 99% of punctures. The repair strings are pre-vulcanized, so they've done away with the "little tube of glue". The repair plugs the hole AND leaves a "patch style" repair on the INSIDE of your tire.
If you'd like to see the tool in action go just click HERE, and watch the demo.
This Slime Medium Tire Tackle Kit is perfect for your ADV tool kit. There are parts here to fix your flat regardless of which bike you are riding. On your tube equipped, no worries, patches are included. The 22-piece kit stores your tire care essentials in easy to browse compartments so you have everything you need to repair a flat tube/tire while on the go. This 22-piece set includes:
- Pencil gauge - 10-50 psi
- Screwdriver-style reamer and plugger tools
- 3 tire plugs
- 5 patches
- 4-way valve tool
- 4 replacement valve cores
- 4 standard black valve caps
- 4 upgraded aluminum valve caps
- Rubber cement
- Scuffer
Warp 9 stem puller
Here is a list of the features of their CNC machined tool.
- Stainless Steel tip, wont break like softer brass tip
- Ribbed head for easier core removal
- Core tip threads into handle to protect tip from damage
- Includes spare valve core in handle for easy trail side repairs
- Tapered handle ends to make tip removal easier with gloved hands and non square edge doesn’t damage tool bags
Flats never occur next to a green grassy field with daisy’s … it always happens way out in the bush and in the dirt and weeds. Change your flat on a clean surface protecting your hubs and bearings from picking up unnecessary dirt and debris with the OBR ADV Gear Flat Mat. Our 24” x 24” Flat Mat provides you a clean area to set your wheel onto while also having convenient slip pockets to stash those easy to loose bits and parts that you removed during the flat repair.
Features
- Heavy duty industrial material construction
- Slip pockets to keep those loose parts and tools close by
- Reinforced center panel to set your hub onto
- Folds flat for easy storage within your luggage
Body
Puig Visor Clip-On
- Suitable for screens with thickness between 3-5mm
- Multi-adjustable visor adaptable to Puig and OEM windscreens
- Visor is mounted by clip-ons and does not need to be drilled to the windscreen
- Visor sizes available include 90x230mm, 100x277mm and 102x325mm
Front fender from ProCycle Plastics (formerly DSA) is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does. Vacuum molded, these are a design improvement over stock. These are fully compatible in any combination with the original factory plastic.
This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.
Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.
A stainless steel front fender brace. Helps stabilize your front fender.
Gives additional strength for carrying a fender mounted tool bag.
Fits on top of the fender and bolts between the fender and bottom triple clamp. Stainless steel won't rust or corrode. Includes hardware.
Requires you to drill one hole in the fender for mounting.
Seats
Corbin seats are custom made to order. You can choose your preferred texture for the top and sides of the seat.
Precision fit to the tank and side panels, Corbin's Dual Sport saddle works with aftermarket tanks too! 1 1/4 inches lower to make for an easier reach to the ground. High density infinite ratio space foam allows us to lower the saddle while maintaining a resilient comfortable ride. Unique contoured shape, combined with high quality space foam provides long range comfort on Dual Sport machines.
Can be color coordinated with a wide range of color options to customize the look of your DR.
Installation: Mounts with the two "L" brackets transferred from your stock seat.
The default vinyl choices are black 'carbon fiber' on top and 'asphalt' on the sides, 'no welts', black logo. You can view all of the available materials and colors through the link below. If you would like your seat built with something other than the standard choices please state specifics in the comments during check out.
Please allow 3 weeks
Cannot be canceled
Seat Concepts dual-sport/adventure seat-kits incorporate a wider seating area for the rider, which results in more even weight distribution, while reducing pressure points. Each individual seat model has been specially designed to increase comfort without compromising ride-ability. The more aggressive the bike, the more aggressive the seat-kit.
Each kit contains detailed instructions for easy "Do It Yourself" installation. This provides the highest level of quality & comfort at an affordable price.
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
Width: | 9 1/4" (235mm) |
Height: | Same as OEM |
Note:
This seat is based on the off-road version of this bike. The street version is 1 inch lower than this seat.
Will NOT fit DRZ 250
This is the secret for being able to put in those 500 mile days. Even a good touring seat can feel a bit firm after a couple hundred miles. Sheepskin gives that little bit of 'cush' and provides superior air circulation. Velcro straps allow easy removal when you don't need it. Measures 14" wide by 19" long.
- Air filled AirHawk 12"x18" cushion custom fits your shape and redistributes pressure that causes numbness and discomfort when you ride
- Seat cushion cover is constructed of a breathable, stretchable Nylon/Lycra blend with a non skid Urethane base
- Open mesh side panels allow heat to escape
- Easily inflates by mouth with no pump needed
- Mounting straps and Repair patch kit included
9" by 9" carbon fiber seat warmer that goes between your seat cover and the foam to keep your backside happy on those really cold days. This improved design produces 25% more heat than most other warmers using just 30 watts.
Kit includes the warming unit, with connector, 24" extension cable, rocker-type on/off switch and stub to splice into your wiring along with complete detailed instructions.
Armor - Bike Protection
- Protect vital engine parts and cases from rocks and debris
- Clear anodized for corrosion protection and good looks
- Skid plates made from 3/16" 5052 H-32 aluminum
- Smooth underside won't snag when crossing logs
- Oil drain hole
- Heat-treated chromoly steel clamps keep plates mounted securely
- All mounting hardware included
bash plate is made from 4mm aluminium 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.
All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.
Protect your frame/paint from scuffs and scratches with frame guards. The DR 250 & DR 350 frame guards are made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.
Don't cut the ball ends off of your levers! These billet spacers move your hand guards outward to allow clearance for the full length of the stock levers. Designed to fit steel or aluminum bars. Includes longer stainless steel mounting bolts.
Developed for the DR650 but may work on other models with long levers. (May require additional adjustment or modification on some models.)
Not compatible with Acerbis and Emgo hand guards
Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.
Images show a set of these hand guards installed on a set of CR High Gunmetal Fly Handlebars with large black deflectors. The far right image shows the need to flip the brackets that attach to the bar on the clutch and front brake side. On the front brake side the clamp must go over the front brake line while on the clutch side it goes under the cable.
Note: This kit includes the handguards only. Deflectors sold separate, can be added by selecting color from drop down menu.
For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.)
- High-impact, composite injection-molded outer guard around an anodized aluminum inner guard
- Includes an indexed steel bar-end insert that mounts solidly and prevents Rally Pro handguards from slipping – even under the most demanding conditions
- Small integral spoiler incorporated into design
- X-Strong universal silver mount kit that fits 7/8” (22mm), Pro Taper 1 1/8"(28mm), Magura and Twin Wall aluminum handlebars included.
Some models with adjustable windscreens may need the windscreen rotated forward, such as the Royal Enfield Himalayan, to avoid contact at full lock. These are not compatible on Honda CB500X's and Honda Africa Twins.
These handguards come with mounts that will work on both standard and and oversize bars. The aluminum wrap-around bar is the biggest on the market with two large plastic shields that are also some of the largest available. The X-Factor hand guards offer great protection from the elements, especially during those colder months when you're trying to stretch out your riding season.
Works with 7/8" or 1-1/8" bars.
X-Factor guards may require you to cut your lever ends down, or use short levers.
The X-Factory Handguards from Acerbis feature a steel bar wrapped with an injection molded Nylon composite. A replaceable dual injected polypropylene shield mounts to the bar offering insurmountable protection from roost, debris, and extreme conditions.
A universal mount kit is included that allows for mounting on either 7/8" or 1 1/8" handlebars.
Will not fit XT250 with stock handlebars (oversize bars ok). Recommend Acerbis Rally Pro X-Strong to clear master cylinder.
- Designed to minimize handlebar vibration for Barkbuster Handguards that can’t accomodate OEM handlebar weights.
- Sleek aerodynamic look.
- Forged Steel with powder coat finish.
- Fit in conjunction with most Barkbusters backbones (except EGO).
- Fits externally to the VPS backbone.
- Available in black.
- Sold as a pair
Weight:
360 grams/pair or
180 grams/each
Fitment Notes: If you have a hardware kit listed below see special fitting notes as additional parts may be required
BHG-010 Requires two additional M6x40mm countersunk bolts
BHG-032 R1200GS/A requires two additional M8x55mm countersunk bolts
BHG-045 G650GS requires two additional M6x65mm countersunk bolts
BHG-050 Will not fit
BHG-051 Requires two additional M6x50mm countersunk bolts
BHG-059 Tiger XC, XCA & XCX (all ’15 on) use M6x45mm bolt from BHG-059 kit
BHG-075 Will not fit
BHG-079 Will not fit
Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.
Features:
- Two mounting points provide secure protection
- Full wrap guards
- Heat treated aluminum backbone bars
- Easy installation
- Tough and weather shielding Storm handguards
- Aluminum backbones are compatible with all Barkbusters deflector guards
What's in the box:
- Left and right aluminum backbone bars
- Inner and outer handlebar mounting hardware for both sides
- Left and right Storm plastic handguard deflectors
- Installation instructions
Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.
NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar
Keep your hands and controls protected from the wind and impact with Barkbusters VPS lever and wind protection handguards. Heat treated aluminum backbones with two mounting points of these handguards provide the strength needed to prevent a tip-over from ending your motorcycle ride. Impact resistant deflectors, available in multiple colors, provide protection for your hands from the wind and brush. Ride longer, more comfortably with Barkbusters VPS lever and wind protection handguards
Features:
- Two mounting points provide secure protection
- Full wrap guards
- Heat treated aluminum backbone bars
- Includes VPS left and right plastic deflectors
- Easy installation
What's in the box:
- Left and right aluminum backbone bars
- Inner and outer handlebar mounting hardware for both sides
- Left and right VPS plastic deflectors
- VPS deflector fastening hardware
- Left and right adjustable position wind extension deflectors
- Installation instructions
Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.
NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar
Construction of these handguards feature heavy duty aluminum guards with colored plastic deflector shields. They offer great protection from those trees that jump out at you on the trail and the cold wind and rain you encounter on the street. They feature a deep bend on the outer bar end for maximum freedom of hand placement and high quality bar mounts on the inside.
Select your desired color.
Must add the corresponding size mounts to fit your handlebar.
For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.)
Please Note: These handguards do not fit the Yamaha T7
You can keep your Cycra handguards even if you upgrade your handlebars to a different width.
Replacement mounts that keep your Cycra handguards fresh and tight.
CNC-machined from billet aluminum for the best fit and strength.
Please Note: These handguards do not fit the Yamaha T7
FUZION guard feature the ultimate in hand protection with a unique design and flexible yet durable material.
The expanded coverage area sweeps back toward your hand significantly increasing coverage making it perfect for cold, muddy or wet conditions.
The FUZION features a unique two position mount and is constructed of molded light-weight closed-cell AEPE foam, which is crush-proof, water proof and extremely durable.
The FUZION will work great for road of offroad riding, where wind deflection is important, and or bouncing off trees is a common occurrence.
Kit includes mounts. Optional replacement mounts available.
Extend your comfortable riding season with Barkbusters BBZ cold weather protection handguards. Designed to fit with or without existing Barkbusters backbones or handlebar weights, these guards offer superb wind protection without limiting access to your grips or controls. Simple to install, they can be mounted or removed within ten minutes without permanent modifications. Ride with less bulky gloves in colder weather with the Barkbusters BBZ cold weather protection handguards.
Features:
- Fits most motorcycle handlebars
- Maximum cold weather protection
- Compatable with or without Barkbusters backbones
- Lined with waterproof membrane
- Windproof
- Full wrap design
- Allows full access of controls
- Does not block view of handlebar thumb controls
- Simple to install and remove
Whats in the box:
- Two BBZ cold weather handguards
- Mounting hardware
- Instructions
The OBR ADV Gear Enduro ¾ Grip Mitt is your answer to cold fingers! Our ¾ open design terminates right at the wrist, but still offers full coverage of the hand while blocking the swirling air flow that freezes finger tips. Their ¾ open design does not cover important controls such as Hi/Lo Beam, Turn Indicator, or Kill Switches making this Grip Mitt perfect for both Off Road, Enduro, ADV, and ATV applications with full wrap hand guards.
Features
- High strength and water resistant 1680d Ballistic Nylon construction
- Universal easy on/off Velcro snap strap attachment system
- Reflective Front Strip for High Visibility
- ¾ Open design provides full coverage of the hand while not impeding controls
- Works with OEM and Full Shield (Cycra/Trackside) style hand guards (Hand guard system required for attachment)
Droppin’ into the weather? Combine Bushwackers Hand Guards with rigid hand guards/deflectors and heated grips for the ultimate protection against the elements. Ride safer and longer with warm, dry and clean hands and controls. Essential gear for motorcycles, snow bikes and snowmobiles.
- Cold/wet weather comfort
- Brush, mud and trail protection
- Strap on/off in seconds
- Multiple mounting configurations to fit most motorcycle makes/models equipped with rigid hand guards and/or deflectors
- Tough stretch polyurethane strap (can be used separately)
- Custom wind foil shapes
- No stitching or pieces to fail
- When not using Bushwackers Hand Guards, straps have a thousand other uses: Lash water bottles, fuel, gear to tail rack. Hold flashlight in place while working in dark. And many others!
- Made in USA
REQUIRED EQUIPMENT: Motorcycle must be equipped with rigid hand guards or deflectors to support Bushwackers while riding.
Materials: Corona (UV) Treated, Matte Finish, .055 Gauge Polyethylene Plastic
Dimensions (flat): 13.5″ (length from end closest to bar clamp to end closest to bar end) x 16″ (widest part at end of bars) x 6″ (narrowest part nearest center of bar)
It may not surprise you that they are covered with HippoSkin™, their waterproof outer shell, and insulated with a generous layer of HippoFat™, a warm, flexible, closed cell foam insulation—both are designed to keep inclement weather away from your hands.
Sold in pairs.
Hand/brush guards are required for proper fitment and for safety reasons.
Hippo Hands go on and off in seconds and never require tools or hardware.
The Backcountry is 9" deep.
If you like to stand and ride, this is the model for you! But… these hand covers also fit to just about any bike. They are also a great option for cruisers with hand guards or lever guards.
They feature a durable, quilted interior and flexible, neoprene cuff which ensures a great fit on so many bikes. The Backcountry is their smallest, most easily adaptable hand cover.
The Backcountry features a front reflective panel for higher visibility in low light situations.
Extra protection in bad weather to help keep your hands warm and dry. These nearly double the protection from most plastic type deflectors.
The outer shell is made from heavy-duty 500-denier nylon with 1/2" closed cell foam to keep the wind, cold and rain off of your hands.
Tools
A portable device that can jump-start your motorcycle or car. It can also charge your cell phone, GPS unit, laptop or other electronic devices via USB cable.
- XP-1 is 6" x 2 7/8" x1" 14oz.
- XP-3 is 5" x 2 7/8" x 1" 12oz.
- Holds a charge for up to 1 year.
GET JumpStarter Mini, the second-generation, multifunctional jump starter. Now lighter and smaller, it's ready to help you restart any motorcycle or scooter when the battery is low. You can also use the powerful built-in LED flashlight or charge your use it as a power bank to charge your electronic devices. JumpStarter Mini comes together with a hard, water-resistant case perfect for carrying it anywhere and protecting it on your journeys.
- Light and compact multifunctional mini starter
- Allows restart of motorcycles and scooters when they are out of battery
- Can also be used as a Power Bank for electric devices thanks to the USB output port
- USB 5V2.4A output allows connection to tablets, smartphones, MP3 etc.
- Has built-in LED flashlight
- Easy to use; provides special protection against overvoltage and inversion of power supply polarity
- Start current: 200A, peak current: 400A, operating temperature range of -20°C to 60°C
- Includes JumpStarter, Smart Cable, 3-in1 USB cable and user instructions
- Measures 155 mm x 79 mm x 16 mm
- Designed to quickly and precisely remove outer bearing race from the steering head without the use of a hammer and punch
- Puller design ensures bearing is pulled perfectly straight to eliminate possible damage to frame
- Works on all tapered bearing races from 47 mm to 55 mm OD
- Precision machined anodized aluminum cup will not damage seal surface
- Brass bearing washers for easy use and long life
- Hardened steel jaws engage securely on inner bearing lip
- Lifetime limited warranty
Motion Pro T-6 Combo Lever has a hex box wrench for your axle nut on one side and a perfectly contoured tire spoon on the other. Manaufactured from lightweight forged T-6 aluminum with a hard anodized finish. These beauties are just under 10 inches long and weigh only 3.5 oz. Available in a 12/13 combo unit and a 22, 24, 27 and 32mm hex ends.
These Rider's Wrenches by Fredette are combination wrenches that have three wrenches in one! A 2-stroke size spark plug wrench - a front axle and a rear axle wrench. Yep, all three in one unit.
Available in the combinations shown that will fit virtually all current dual-sport machines.
The Mini-Morph is actually a bicycle pump, but it is the best manual compact pump for adventure / dual-sport riding. It has a fold-out foot and handle and a 4 inch hose so you can set it on the ground to pump!
This thing is small enough to stow away in just about any bag and go unnoticed until you need it to fix a flat or add air after a long arduous ride.
It seems that while packing for every adventure … we always end up with a few items that were either neglected to be packed, were last minute gear additions, or just needed to be packed in a readily accessible location…. The OBR Adv Gear Tool Pouch is the perfect solution for these miscellaneous items. Once packed the tool pouch can be slipped into any bag or attached externally using integrated webbing loops that are built into the pouch.
Features
- Heavy duty industrial material construction with high strength UV resistant nylon webbing
- Heavy duty #10 coil zipper that won’t jam up in the dust
- External reflective webbing with Molle loops
- Pouch dimensions 5” x 13”
* Tools not included
Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.
The three forces of suspension, testing procedures, even the black arts of chassis geometry: Thede explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.
Clymer manuals are the most user-friendly repair manuals. They are written for the do-it-yourself-er as well as the experienced mechanic by industry experts. Step-by-step instructions based on the complete disassembly of the machine. This manual in written to cover 90-94 models but nearly all of the information will apply to newer models also.
- Resists extreme environments; won't melt up to 500°F; remains flexible to -60°F
- No adhesive; fuses only to itself
- Forms a water- and air-tight seal
- Tensile strength of 600 psi
- Insulates to 400 Volts/Mil
- Tight insulating tape is 1" W x 10' L and stretches to three times its length
Changing tubes or tires without the right tools can be a real chore. Don't fight your snug beads any longer, use this 27" long tool that opens to 7-3/4" to provide the leverage you need to easily break your tire bead. Constructed from heavy-duty steel with comfortable no-slip grips, this tool makes the job a snap.
No more fighting to keep the bead down while installing or repairing your off-road tires. The Bead Buddy holds the tire bead down in the drop center of the rim during tire changes making changes as easy as possible. Machined from tough 6000 series aluminum the Bead Buddy is light weight and compact enough for any tool pack. The Delrin securing thumb screw insures no scratches to your rims.
The Bead Buddy is NOT recommended for use with Bib Mousse tubes.
- Durable 6061 aluminum with blue anodized finish and laser engraved logo
- Used to push the tire bead down into the drop center of the rim on off-road wheels while using tire tools to change tires
- Hooks over spoke and pushes bead down on opposite side of tire from tire irons
- No more fighting to keep bead down while installing off-road tires
- Innovative multi-use tire tool set
- Breaks the bead on most street and off road motorcycle tires
- Integrated tire spoon for tire removal and installation
- Light weight and compact size is perfect for tool packs
- Ergonomic handles with crossguard to keep hand from riding forward
- Forged 7075-T6 aluminum construction for strength and durability
- Black anodized finish
- Patent pending
Available in 9.5" aluminum (ideal for travel) and 16" forged steel (useful in a home shop/garage)
The Pro Fill Air Chuck from the people at Motion Pro is perfect for those tough to reach valve stems with its pivoting angled head. The design gives users extra hand clearance to avoid hot brake rotors or dirty chains. Billet manufactured from aluminum gives it a precise fit and function combined with light weight. It is finished off with a beautiful blue anodizing and then the Motion Pro logo is laser etched on forever. 1/4" NPT female inlet allows use with common air hose couplings and fittings.
A great addition to any tool box!
The MotoPressor Puncture Repair Tool combines the four tools essential for tubeless tire repair into a single tool.
With the motorcyclist in mind, they've designed a "4 in 1 multi-tool" that uses pre-vulcanized repair strings and packs into a sheath measuring a mere 130 x 68 x 50mm, that's small enough to fit in your pocket. The tool contains a pair of pliers, a rasp, an insertion tool and a sharp knife, which is all you'll need to fix 99% of punctures. The repair strings are pre-vulcanized, so they've done away with the "little tube of glue". The repair plugs the hole AND leaves a "patch style" repair on the INSIDE of your tire.
If you'd like to see the tool in action go just click HERE, and watch the demo.
Warp 9 stem puller
Here is a list of the features of their CNC machined tool.
- Stainless Steel tip, wont break like softer brass tip
- Ribbed head for easier core removal
- Core tip threads into handle to protect tip from damage
- Includes spare valve core in handle for easy trail side repairs
- Tapered handle ends to make tip removal easier with gloved hands and non square edge doesn’t damage tool bags
Use simple leverage to easily lift your dirt bike up on to a flat platform.
The platform angle adjusts easily so either wheel can be off the ground quickly and safely for work or cleaning. These adjustments can be made with the bike on the stand.
Folds up for easy storage and transport.
Adjustable legs for use on any terrain and allows for even lift height for any dirt bike.
*Closeout item, as is, no warranty.
This Super Siphon has a (1/2 inch x 6 foot) long hose, which makes it quite easy to transfer fuel from one bike to another! Simply, shake the hose to prime it and get fuel moving. The hose is resistant to gasoline and any other hazardous chemicals. Roll it up, stuff it in your bag and you will be very happy whenever you need it.
Made from precision-drawn, chrome-vanadium tool steel, the BikeMaster® 9-Piece Ball End Hex Wrench Set and Holder features a bead-blasted surface for a better grip and a corrosion-resistant coating. They have a ball end, allowing an angled reach and access to obscured bolts. It comes with a durable holder and manufacturer's lifetime warranty.
Comes with sizes 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm and 10mm
This Motion Pro tool pulls bearing out of those blind holes in engine cases etc. Set includes 30, 25, 20, 17, 15, 12, 10 and 8mm collets. 2 pound slide hammer. Crossbar type shaft allows easy collet removal. Necessary tool for most transmission rebuilds. Can be used for wheel bearing removal.