Search Products

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Warp 9 Supermoto wheels are built with billet hubs, 7000 series aluminum rims and laced and trued with stainless steel spokes and nipples.

The 3.5" x 17" front wheel includes a 320mm brake rotor and caliper relocation bracket.

The 4.25" x 17" rear wheel also comes with a rear brake rotor already mounted.

Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.

Rear wheel Includes Sprocket Carrier with 525 40T Sprocket installed that matches selected hub color.

A portable device that can jump-start your motorcycle or car. It can also charge your cell phone, GPS unit, laptop or other electronic devices via USB cable.

• XP-1 is 6" x 2 7/8" x1" 14oz.
• XP-3 is 5" x 2 7/8" x 1" 12oz.
• Holds a charge for up to 1 year.

• Wider, lighter, stronger design. Platform is 60mm wide x 100mm long, overall approx length from center of footpeg pin to end of peg is 115mm
• Widest (mm) and lightest pivoting pegs on the market
• Upgraded heavy duty, long life springs
• Unique multi-directional grip pattern
• Outstanding build quality
• Overhaul kit includes: 2 pivot bushings, 2 pivot tension springs, 2 lock nuts, 2 washers, 6 o-rings, 2 split pins and instructions

The must-have accessory for adventure-touring. Greatly eases basic chain maintenance, tire changes, parking, and bike cleaning. Super-strong steel construction features typical German design and high engineering standards. Superb integration with the factory exhaust and side stand components - retain all existing features without sacrificing lean angle or clearances.

All hardware needed to mount the centerstand included. Typically installs using basic hand tools. No welding, cutting, or drilling of existing frame or body parts required. Tough black powdercoated finish with some gray fittings or hardware as applicable. A double-retention spring is included as a safety feature to prevent the centerstand from contacting pavement if one of the two springs should fail during a ride. Designed to work with OEM components -- we cannot assure fit with aftermarket exhausts or other accessories.

• Ground clearance & cornering clearance problems
• Difficulty in lifting the lowered bike onto the centerstand

The SW-Motech Centerstand is something that should be an OEM item. Essential for flat tire repairs, tire changes, chain maintenance, oil changes, loading/unloading luggage and many other day-to-day maintenance operations.

Integration with OEM exhaust and sidestand is exceptional. The extended foot lever maximizes leverage making for easy elevation of your Twin. There are no penalties in clearance for these benefits. Tubular steel construction with a heavy-duty black powder coat provides for a stable foundation for supporting your motorcycle. No sacrifices were made to the performance or clearance of the Twin.

Installation is a simple bolt-on procedure; no drilling, cutting, welding or relocating other components for fitment. Package includes all necessary mounting hardware and detailed instructions.

Please Note that the Centerstand works perfectly with the Skid Plate Extension.

The basic purpose of a center stand serves to enhance ownership experience by easily raising the rear wheel completely off the ground for drive chain lubrication and adjusting, tire & tube patching/replacement and even FRONT wheel work. Those fortunate enough to have owned a motorcycle equipped with a center stand have come to learn the game-changing role it can play -even off-road.

Center stands have many more inherent uses including:

• Increased stability when parked on soft ground
• Easier cleaning and pre/post ride inspections due to the upright positioning
• Less effort required to place on its stand when compared to a milk crate or portable stand
• Superior parking/storage advantages in tight spaces

Unlike a basic portable moto stand, your center stand is ALWAYS available wherever your need it, whenever you need it.

When in use, this kit raises your rear tire 3/4" off the ground. When retracted, the stand tucks away, 100% unobtrusive to the rider and passenger. A robust retention spring ensures the stand remains retracted, even on the roughest trails.

Each kit comes with all hardware and detailed instructions. All parts are powder coated black with a fine texture

Designed to enhance overall performance when installing a high-flow jet kit. This CDI box enhancements include:

• Altered ignition advance curves
• Wire lead for a tachometer

This unit may also be used to replace a defective CDI box on a stock machine. 

Please note that the internal circuitry of Rick's CDI unit necessitates the engagement of the clutch or kickstand neutral safety switch for proper operation. Specifically, the clutch must be engaged (pulled in) when the kickstand is in the down position. This requirement may not be present in the original Yamaha OEM CDI unit.

• Permanent battery leads with integrated battery status/charge system monitors for 12V lead-acid batteries or lithium batteries
• Monitor charge or confirm if the charging system is working correctly
• SAE charge port with weatherproof sealing cap
• Two automatic modes: battery charge level monitor and charging system test

Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position.

The Firepower features increased cranking amps over lead acid batteries and has a very fast recharge cycle, and can be brought up to a 90% charge within 6 minutes. It also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.

220 CCA 12V/48WH
Package Dimensions: 6.20 x 3.70 x 5.25

Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position.

The Firepower features increased cranking amps over lead acid batteries and has a very fast recharge cycle, and can be brought up to a 90% charge within 6 minutes. It also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.

165 CCA 12V/36WH
Package Dimensions: 6.20 x 3.70 x 4.45

Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position. There is no hazardous acid or heavy metals, it is non-explosive and non-combustible.

The Firepower features Increased cranking amps over lead acid batteries and has a very fast recharge cycle and can be brought up to a 90% charge within 6 minutes and also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.

220 CCA 12V/48WH
Package Dimensions: 5.60 x 3.25 x 6.38

• Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life
• Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material
• Triple-lip seal design
• Dyno-tested to last 3 to 4 times longer than OEM seals
• Directional ribs allow seal to be installed easily
• Sold in Pairs

• Kit includes a pair of oil seals and dust seals; no bushings or other rebuild parts included
• Seals have been tested to over 1 million strokes in R&D development
• Every part meets or exceeds OEM quality standards
  
   

Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes Fork Seals and dust wipers.

Includes all components needed to rebuild you forks.

• Inner and outer bushings
• Oil and dust seals
• All necessary o-rings

The Pro-Series is an excellent replacement for the stock shock. With both compression and rebound adjustable as well as preload adjustable, you can tailor the performance to match your riding style. Compact and rigid design with piggyback type reservoir specifically engineered for your WR250R. Fully serviceable shock is designed for the long haul.

Select the spring you want installed based on the load you plan to carry. Choose the 'standard' 8.15kg/mm spring for rider/ luggage up to 220lbs. Weigh more than 220 lbs, or are loaded to the max, think about the 10.19kg/mm 'heavy' spring.

Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.

This spring is 8.0kg/mm

OEM spring rates are 5.7-7.6kg/mm progressive style.

The V-Strom suffers from poor compression damping and limp rebound damping. The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.

• Bolt-on shock valving for riders serious about suspension performance
• Improves control, traction, plushness and bottoming resistance
• Improved, long-wearing, low-friction sealing design decreases fade
• Includes complete instructions

Rebound Separator Valves replace the shock shaft nut with an asymmetric valve (provides a different flow rate in each direction of travel) to increase traction and improve bottoming resistance and pitch control.

Why is this needed? On a standard shock the Low Speed Rebound Adjuster flows the same on compression and rebound. In testing, when the lowest speed rebound damping is quick enough to get good traction, the lowest speed compression damping is too mushy. This causes a vague feeling and bottoming on long duration hits like big dips or gullies in Dirt. For Pavement RSV's have the added benefit of pitch control (front to back movement during acceleration and braking). This keeps geometry more consistent.

The Valve has a partially drilled bleed hole in the center. IT MUST BE DRILLED BY THE END USER TO THE PROPER SIZE (2.8mm).

Replace the internal components in your shock with a completely updated design with adjustments for both compression and rebound damping.

The new shaft assembly has improved valving for both compression and rebound, a thicker, stronger shaft, new seal head and bottoming bumper. Comes as a complete assembly ready to go into your shock body. You can add choice of rear spring (required).

Add a bottle of 3w Shock Oil to your order so you can start your project right away.

Complete Pivot Works kit to replace the bearings and seals in the XR650L swingarm pivot.

Convenient kit eliminates looking up many part numbers.

Each kit contains bearings, pins, collars and seals manufactured to OEM specifications for a perfect fit.

Complete kit to replace the bearings and seals in the XR650L shock linkage. Includes the lower shock bearing.

Complete kit to replace the bearings and seals in the DR350 shock linkage. Includes the lower shock bearing.

Features:

• Clips on to brim of hat for hands free use
• Adjustable head for precise illumination
• Wide angle LEDs provide a flood of light
• Internal rechargeable li-ion battery (micro USB charging cord included)
• High and low settings, up to 4 hour runtime

A compact and lightweight solution to eliminate the SNAP for a safer tow. If you have ever towed a motorcycle you are familiar with the snap that comes with a traditional tow strap. GCAG made the Dynatow with a section that gives 32 inches of stretch so both riders have an easier tow.

The 26 foot total length gives you enough room to maneuver around obstacles and allows the freedom to choose better lines if you are towing in the gnar.

You can also use this as a recovery strap. You can girth hitch the loop end to the bike and throw the other end to a friend to pull. The dynamic properties of the Dynatow will help assist the pull. All of this functionality fits in a flat pouch about the size of sandwich and only weighs 12.8 oz. Throw it in your bag and be prepared.

Specifications:

• 1" Nylon Webbing - UV resistant and heavy duty.
• Tough Tensioners - The elastics are woven inside tubular nylon webbing for protection and strength.
• Hi-Viz Color - The bright green color will make this easy to see.
• Sewn Loop - The towing rider can choose to use a loop around the peg or wrap it. The loop also gives options to girth hitch if needed.
• 1000D Cordura Storage Pouch- protects the strap against abrasion while stored and keeps it compact.
• Multi Use - All good adventure gear is multi-use. Here's a few ideas.
  • Ridge line for a tarp.
  • Clothes line while camping.
  • Recovery strap for a friend to pull on.
• Compact and Lightweight
  • Dimensions - 8 in x 6 in x 1 in
  • Weight - 12.8 oz
• 1,000 LB Working Load - They made it strong just like all of their products.

Please consider the following before use: Practice before you need to use this product. Always inspect your Dynatow strap before use and NEVER use a worn strap. They recommend a proper training class to learn safe methods for towing a motorcycle.

The Giant Loop Tow Strap is a multi-functional tool that helps get you or your riding friends out of sticky situations.

This Cordura® Ballistic tow strap, designed with sewn loops on each end, can be girth hitched around a tree, bumper, rock, etc.; or used with footpeg-to-footpeg or other motorcycle (and snowmobile, ATV, snow bike) towing techniques. Constructed in the USA from ultra-durable custom woven Cordura® Ballistic webbing, which folds up into a compact integrated cover made with 22 oz. vinyl-coated polyester, or what they like to call “truckers tarp.”

Doubles as a quick deploying, super-strong ridge line for pitching a shelter tarp.

• DIMENSIONS: Measures 14’-9″ L (450 cm), with 6″ (15 cm) loops sewn into each end. 10″ L x 2″ W x 2″ D (25 cm L x 5 cm W x 5 cm D) (packed)
• WEIGHT: 5 oz. (141 g.)

Color may vary based on manufacturer availability, quality will not be compromised.

The GCAG handles are comfortable to pull so whoever is helping will pull harder, and they are soft against your fender so you won't have any annoying bouncing, noise, or graphics damage.

GCAG dirt bike lift strap handles are constructed of 1" thin nylon webbing with flat stainless steel tri-glides for attachment. The grip section is built with 1" climb-spec tubular nylon webbing and a comfort grip handle.

Features:

• Quick tool-less install
• Stainless steel hardware (no metal contacts your fork tubes)
• Comfort Grip Handle
• Fits any bike

Simplify self recovery with this quick deploy Z-Drag kit. It can sap your energy trying to get your bike unstuck. It can also fall in a way that makes it very difficult to pick up. The Z-Drag is a common rig to give you a mechanical advantage for reduced pull. The combination of roller cams provides a 4:1 pulling ratio for self recovery and a 5:1 ratio when you have help. A laminated instruction card is included in the bag.

These gaskets seal the joint between the head pipe and muffler. They are easily damaged when removing the original muffler. Get a fresh pair now to ease installation of your new performance muffler. Sold as a set of 2.

The EVO R is a tried-and-true series that will save weight, add noticeable performance gains and sound tremendously better than stock.

• Hard anodized oval shaped aluminum muffler
• TIG welded reinforced muffler bracket(s)
• 304 stainless steel mid pipe
• Red powder coated stainless steel end tip
• Lighter than stock exhaust system
• Huge horsepower and torque gains
• Sleek muffler design allows for maximum clearance
• Removable screen-type spark arrestor included
• Handmade in the USA
• 1 Year Limited Manufacturer’s Warranty

• Select applications available in SX version that is designed for more low to mid-range power and an MX version that is focused in the mid-to-upper rpm range
• Act as "pre-muffler" helping to lower the decibel output
• Available in stainless steel for strength combined with light weight, or in titanium for even greater weight savings
• Utilize FMF's patented module precisely located at the initial stage of the header for specific applications
• Horsepower is increased as much as 10%
• The expansion and contraction of exhaust sonics through the system causes increased flow
• Position "Bomb" increases performance

The EVO R series draws on our rich heritage of making power. Offered for various off road MX and sport ATV models, the EVO R is a tried-and-true series that will save weight, add noticeable performance gains and sound tremendously better than stock.

• Hard anodized oval shaped aluminum muffler
• TIG welded reinforced muffler bracket(s)
• 304 stainless steel mid pipe
• Red powder coated stainless steel end tip
• Lighter than stock exhaust system
• Huge horsepower and torque gains
• Sleek muffler design allows for maximum clearance
• Removable screen-type spark arrestor included
• Handmade in the USA
• 1 Year Limited Manufacturer’s Warranty

The Chilly Exhaust Heat Shield is the most effective heat shield on the market. The innovative three piece design consists of a top shield attached to 2 rails with rivets and spacers. This reduces the contact area and slows down heat transfer. They have incorporated a patented, insulated reflective blanket on the underside of the shield to reduce radiant heat transfer. The included stainless steel clamp makes it simple to install.

We highly recommend a heat shield if you run soft luggage without hard racks.

FEATURES:

• Solid Top Shield - The logo is laser etched and there are no cutouts on the top shield. This prevents radiant heat from passing straight through to your luggage.
• Side Rails - By isolating these with spacers the heat conductive surface area to the top shield is reduced and slows down heat transfer.
• Radiant Heat Shielding - The reflective insulated blanket on the bottom of the shield is the real hero. This patented material won't be found anywhere else in the motorcycle industry. 
• Stainless Steel Clamp - Slots have been provided in the side rails to make installing as easy as it gets.
• Brushed Aluminum - Lightweight and looks nice.

DIMENSIONS:

• Length 7.5" (190mm) x Width 3.5" (76mm) x Height 1" (25mm)
• Clamp fits any exhaust 3.5" - 5.5" (89mm - 149mm)

Stock and typical after market drain plugs can protrude past some skid plates. This steel low profile drain plug stays inside the skid plate so it can't be snagged by passing objects.

Comes with 4 crush washers.

The Rekluse EXP employs the same EXP assembly as their premier product; the difference is that it fits into your stock clutch assembly, saving you money! Now you can enjoy the benefits of Rekluse auto-clutch technology on your KLR.

An auto-clutch automatically feeds out the engagement of the clutch using centrifugal force. This allows you to start and stop without touching the clutch lever. The automatic feed is fully adjustable to suit the rider's needs while retaining full manual override with the clutch lever. This automatic feed delivers easier on/off throttle transitions, improved traction, better control, and more confidence.

Complete set of friction plates, HD springs and steel separator plates prevent premature driven plate wear, oil muddying and loss of stack height. Built with swaged aluminum carriers that spread the load on the clutch basket and prevent clutch basket "dogging". Anti-swell, alloy impregnated heavy-duty facings for smooth clutch action. Allows modulation, unlike paper clutches which tend to snatch. Don't forget to add a fresh gasket.

Generator cover gasket to seal up the cover once you have your new Doohickey in place. New OEM gasket. What else can we say? If in doubt, put in a new one.

Adjusting your valves or setting your cam chain tension? Here are the O-Rings that fit in the TDC sight plug and the crankshaft nut access plug.

Complete set of engine gaskets with oil seals.

• '13-Current kit by Moose Racing
• '08-'12 kit, genuine Yamaha parts

Genuine Suzuki replacement gaskets.

Complete gasket kit includes all gaskets and oil seals necessary for rebuilding your engine.

Complete top end gasket kit for the mighty XT250

• High-tech materials provide unmatched reliability and performance
• Rebuild the top end with total confidence as each set is designed for durability and accurate fit
• Oil seals are genuine OEM replacement seals
• Performance sets designed for a piston replacement
• Includes every gasket, O-ring and seal required to rebuild a top end; valve seals, head, base, exhaust, tensioner, and other misc. gaskets and O-rings
• Does not include formed rubber valve cover gasket
• Formed valve cover gaskets are included in complete kit with oil seals

285cc big bore kit includes:

Wiseco piston 78.00/+5.00 10.5:1 (with rings, pin & clips): 

• All Wiseco Pistons are forged from high silicon, low expansion aluminum which offers superior strength, reduced weight, improved heat transfer, and longer life.
• Diamond turned finish from one of the many CNC computer controlled turning centers guarantees you a perfect finish with no size variation. Wiseco pistons can be installed in any of today’s cylinder bore compositions
• Wiseco’s state-of-the-art computerized manufacturing facility is dedicated to supplying both the high-perfomance racer and recreational enthusiast with the finest forged piston available in today’s market place.

HotCams stage 1 camshaft:

• High-performance racing camshafts
• Stage 1 performance camshafts are drop-in cams that are designed to be used with stock valve springs
• In most applications, Stage 1 cams deliver more torque.

Complete top end gasket set:

• High-tech materials provide unmatched reliability and performance
• Rebuild the engine with total confidence as each set is designed for durability and accurate fit
• Oil seals are genuine OEM replacement seals
• Performance sets designed for a piston replacement
• Includes every gasket, O-ring and seal required to rebuild a top end; valve seals, head, base, exhaust, tensioner, and other misc. gaskets and O-rings
• Does not include formed rubber valve cover gasket
• High-compression kits use .012" thick base gaskets to raise compression
• Cost-effective way to raise compression without expensive high-compression pistons or cylinder head work
• All gaskets made in the U.S.A. 

This is a great combination and a big 'bang for the buck' performance increase. 

No re-sleeving required. You will have to have your cylinder bored to fit the larger piston.

10mm diameter - Includes three valve shims of each size from 1.85 to 3.20 in .05 mm increments. 84 shims in total, 83 cents per shim!

The B&B Off Road Engineering rear carry rack is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible. Our carry racks are Tig welded with a polished finish and are sturdy enough to use as a grab handle.

DIMENSIONS

Width Flat Surface Approx 18cm

Length Approx 33cm – Total Length Approx 45cm

Please Note- To fit rack, two holes need to be drilled into the rear guard. The position of holes are already marked on genuine Yamaha guard so no template is required.

Features:

• Rear rack comes with grab bars, designed for specific models
• Flat surface with many fitting holes for cargo box and its box base installation
• Comes with loading hooks for secure luggage holding
• Can be used as grab bars for passenger
• Can be used with GIVI universal box bases
• Maximum loading capacity is 5 kg / 11 LB

The Nomadic Rack is a favorite for dual-sport riders with ruggedness and ease of installation. This rack does not need to be removed for under-seat maintenance. The mounting area is large 11" x 10" and the rack weighs just under 3 lbs. It constructed of 16 ga. steel and fully welded, then powder-coated black with a shot-peened look. Has a rigid four point mounting system and doubles as a grab handle. Complete instructions and stainless steel hardware are included.

The Side Bag Hauler Kit has been designed to work with or without the GCAG Uprising Soft Rack. These straps allow you to use standard dry bags for side luggage. When installed properly you will be able to thrash about offroad and your luggage will stay put! With this setup it is very important to strap your bag in tightly and double check your exhaust clearance.

Bags can be rigged horizontally or vertically.

Hard luggage can increase your risk of injury, especially on offroad terrain. With this system you can reduce your potential of injury and have adaptable, waterproof luggage.

Kit Includes:

• 4 Heavy Duty Cam Buckle Tension Loops
• 4 Four Foot Runner Loops

With 3.5-liters of packable volume, the super-rugged, universal roll-top Possibles Pouch™ provides enough capacity to carry a set of tire irons, spare tube, compressor, tools, and other small offroad essentials. The bag also allows one to add external pockets to Giant Loop’s MoJavi Saddlebag, Coyote Saddlebag, Great Basin Saddlebag, and MotoTrekk Panniers.

The Possibles Pouch gear pocket is 100% waterproof, dustproof, and mudproof. It can be anchored to engine guards, crash bars, tail racks, or any other secure attachment point on virtually any motorcycle make or model. Add Giant Loop’s bolt-on Tail Rack for an instant trail riding solution that gets the weight off your body and onto the bike for improved performance and less fatigue.

• VOLUME: 3.5 liters (214 cubic inches)
• DIMENSIONS: 10.5” L x 5.5” W x 3.0” H (27 cm L x 14 cm W x 8 cm H).
• MATERIALS: Rugged Bomb Shell™ 500D PVC tarpaulin body.

• Manufactured to perfectly fit the factory airbox, these filters use top-quality materials from around the world including the Powerflow filtering media
• Direct replacement of original equipment filter with no need to change carburetor jets or settings
• Designed and developed to meet the demands of high-performance engines

Unsurpassed in airflow, dirt stopping and overall performance. Adding a pre-filter to your intake system gives you extra protection from damaging contaminants.

Use this tool to check for air leaks in two-stroke engines. It includes air pressure gauge, pump-up bulb and most fittings and adapters for single and twin-cylinder two-stroke motorcycle engines. Packed in a convenient carrying case with instructions.

Made from precision-drawn, chrome-vanadium tool steel, the BikeMaster® 9-Piece Ball End Hex Wrench Set and Holder features a bead-blasted surface for a better grip and a corrosion-resistant coating. They have a ball end, allowing an angled reach and access to obscured bolts. It comes with a durable holder and manufacturer's lifetime warranty.

Comes with sizes 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm and 10mm

The Phillips type screws used in Japanese motorcycles are actually Japanese Industrial Standard (JIS) screws and are easy to strip if you are using a regular Phillips screwdriver.

Here is a little kit that will make removing and replacing JIS screws much easier. Includes 2 each of JIS No. 1, No. 2 and No. 3 bits.

These will work in other bit holders and have a mild magnetic tip.

Features:

• 2-ended design combines brush and pick with a curved spade to help vehicle clean off mud and debris
• Curved spade for the big stuff
• Brush head to clean controls and radiator
• Pointed tip for foot pegs and hard to reach places
• Includes a hanging hole for easy storage in the garage
• Ergonomic handle is made from durable ABS plastic
• Patented design

Features:

• Two tools in one. One end is used to loosen stuck hose, the other end assists in pulling the hose off the fitting
• Reduces the possibility of damage to hoses and related components
• Lock nut at base of each tip allows 360 degree adjustment or removal of one tip for use in tight spaces
• Compact aluminum handle provides solid grip and excellent control
• High-quality steel tips with durable black oxide coating

This is the ultimate radiator guard for the CRF250L. Protects your  radiator from both front and side impacts.

A rear mounting bracket provides that extra support. Constructed from 1/8" aluminum, the kit includes all necessary mounting hardware for a very simple installation.

Givi makes a great set of Crash Bars available for the Africa Twin. If your intentions include off-road riding of any kind, you really should not go without protection. Not only for you, but for your bike too. Even a slow-speed tip-over can cause damage that would make riding away impossible.

For the upper set, you just need to select the matching color to the lowers you have ordered. Install them all at once, or the lowers alone for a while, then the uppers. You cannot order the uppers without the lowers though as they will no mount correctly. The upper crash bars protect important radiators and bodywork. Essential in the event of any kind of crash. These also make excellent mounts for auxiliary lights for added visibility.

Included with each piece you receive a complete set of instructions and all mounting hardware required, in typical Givi fashion.

NOTE: The upper units REQUIRE the lower crash guards for proper mounting and are not a stand alone item!

Please Note that these Crash Bars are also compatible with the Givi Skid Plate.

Protect that vulnerable rear master cylinder with this thick aluminum guard from JNS Engineering. CNC laser cut then formed and given a clean black powder coat finish. Includes new button head screws and aluminum spacers.

• Protect your investment with the Works Connection rear brake caliper guard that is simple to install and does not break the bank.
• Works Connection built the rear brake caliper guard from CNC'd aircraft grade 5052 aluminum for lightweight durability.
• No need to modify anything with this rear brake caliper guard because Works Connection includes all the hardware to easily bolt on.
• Works Connection designed and built the rear brake caliper guard in the USA.

• Next generation skid plate made with high strength plastic
• Designed to protect the shock absorber linkage from impacts, mud and sand. It allows you to slide easily on natural obstacles ensuring a smooth ride. 
• Impact resistant material effectively protects against stones, earth and mud
• Flexible and lightweight plastic reduces vibration and surface damage to chassis and engine
• The air intakes are designed to give more lightness, aeration and facilitate the washing operations under the engine, reducing the entrance of gravel, earth and mud
• Using the original fasteners of the bike the assembly/disassembly is intuitive to facilitate the normal maintenance and washing of the engine
• Extended protection areas on the side housings, on the water pump and in the chassis areas

• Protect vital engine parts and cases from rocks and debris
• Clear anodized for corrosion protection and good looks
• Skid plates made from 3/16" 5052 H-32 aluminum
• Smooth underside won't snag when crossing logs
• Oil drain hole
• Heat-treated chromoly steel clamps keep plates mounted securely
• All mounting hardware included

• Protect vital engine parts and cases from rocks and debris
• Clear anodized for corrosion protection and good looks
• Skid plates made from 3/16" 5052 H-32 aluminum
• Smooth underside won't snag when crossing logs
• Oil drain hole on all required models
• Heat-treated chromoly steel clamps keep plates mounted securely
• All mounting hardware included

The 2023-2024 Honda XR150L skid plate protects your bike no matter the terrain. The XR150L skid plates are made from high quality aluminum and offer full coverage. It comes with unique, proprietary hardware that requires no drilling and tapping into your dirt bike. Comes standard with a clear anodize for extra protection. Buy your skid from the industry's longest-running skid plate manufacturer. Ensure your Honda stays safeguarded in style—made durable in the USA.

• Skid plate fits 2023 and up XR150L models
• High quality hardware included - custom made to never fail
• No drill and tapping required
• Extremely easy and fast to install
• Made in USA

bash plate is made from 4mm aluminium 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider.

All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.

Stock chain guard crack and crumble on you? Won't happen to this unit CNC machined from 2.5mm marine grade aluminum. Polished to a beautiful sheen that will give your DR that little twinkle as well as better protection.

Fits all TW200's. Includes a new cap and uses the stock petcock. Capacity is 2.7 gallons (stock tank is 1.8 gallons).

  Clarke tanks do not come with a vent hose or vent cap.

Please note: All Clarke TW200 tanks have blemishes due to the mold used in their manufacturing process. Also, side panels are likely not snap into tank as they do on the stock tank.

For those people who have been wishing for a dual petcock setup for their Acerbis 5.3 and 6.6 gallon fuel tanks. Install this kit to get the last bit of fuel from the right hand side of the tank without tipping the bike on its side. Includes the right hand fuel valve, o-ring, screws, tee fitting, fuel hose and spring action hose clamps. You will have to drill the hole in your tank for the petcock standpipe. For Acerbis tanks only.

This is a high-quality seat cover offered by Moose for the DR650. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam. Strong marine-grade vinyl that's made to last. UV protected from sunlight for extended use and has double stitching for extra strength.

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

Our casual t-shirt with a classic ProCycle Logo on the front and a topo map of our favorite local riding spot on the back. High quality soft t-shirt perfect for everyday wear.

T-Shirt Specs:

• Retail fit
• Tear-away label
• Side seamed
• Shoulder taping
• Black Heather: 4.2-ounce, 90/10 Airlume combed and ring spun cotton/poly, 32 singles
• Heather Dust: 52/48 Airlume combed and ring spun cotton/poly

Direct replacement cables for your T-Dub. OEM or high-quality replacements will keep you on the road or trail. Pay attention to the model year for correct fitment, then select the cable type: Throttle, Clutch or Speedo, they're all here.

• Manufactured to exact measurements to meet or exceed oem specification
• Tempered steel wire housing with an inner nylon sleeve for long life & smooth operation

Genuine Yamaha replacement throttle cables.

Folding tip, forged aluminum shift lever from BBR Motorsports. Stronger and lighter than the stock shift lever.

• Strong forged aluminum construction
• Steel knurled folding tip (chrome plated)
• Anodized titanium finish
• 1/2" longer than stock

Quality replacement levers. Standard length.

Aero Tapered Aluminum (ATA) Oversize (or Fat Bar) Handlebar.

• GP High Bend
• Black in Color
• Aerospace grade, heat treated 7075 T6 aluminum construction
• Shot-peened and anodized finish for maximum strength and durability
• Calibration marks for precise mounting
• Clutch-side knurling for maximum grip adhesion
• Stronger and lighter than conventional aluminum handlebars
• Controls the flex to dissipate shock and impact which reduces rider fatigue
• The molded bar pad provides superior impact protection and features and innovative mounting solution for easy installment and positioning
• 1 1/8" clamping diameter tapers to 7/8"at bar ends
• Handlebar is lighter than the competition; it weighs only 1.4lb
• Durable, laser engraved graphics
• 80mm bore depth to accommodate most handguards

For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8  adapter (sold separate).

• Ergonomically designed
• Medium-density Thermoplastic Rubber (TPR) compound provides excellent feedback and control, without sacrificing durability
• Full diamond pattern for an unparalleled feel in both wet and dry conditions
• Inner diameter optimized to keep grips secure in any conditions
• 115mm overall length; fit 7/8" bars and throttle sleeves

Here is a complete kit to install oversized tapered 1-1/8" handlebars on your DR650. Warp9 handlebar clamps bolt to your stock triple clamp adding an additional 1" to the height.

Alloy oversize bars offer more durability and eliminate the crossbar which opens up your dash area for more goodies. Black in color.

Handlebar mounts that replace your stock clamps.

These raise your handlebars 1 inch.

Choose 7/8" for standard handlebars or 1-1/8" to allow installation of your choice of oversize/ tapered handlebars.

When upgrading your Suzuki DR650 with LED turn signals, it's required to install a diode module to prevent all of the signals from blinking at once regardless of left or right signal activation. Some riders choose to splice and solder their own solution, but we like things plug and play. That means all you have to do is plug in the TST kit and you're done! There's no need to cut or splice your OEM wiring harness or break out the soldering iron and electrical tape.

• Plug and play installation - meaning no cutting, splicing, or soldering
• Eliminates issue of all signals blinking when activating only one side of turn signals
• Enables power to flow in single direction from LED turn signals to the dash indicator
• Does not fix hyperflash (LED turn signals flashing faster than OEM specified rate)
• (1) TST Plug and Play Diode Module
• 1 Year Warranty 

Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.

White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.

Dazzling bright Amber blinker functions. 

All in a spring-loaded stock to prevent damage from a tip over, crash or impact with brush, trees etc. They will bend 360 degrees, but are stiff, durable and nearly unbreakable.

Kawasaki KLR650 Gen 3 / KLX300 Specific plug and play kit using factory connectors, flasher and block off plates.

This is the ultimate headlight upgrade for your XT250! It’s a plug & play kit which includes the newly released Morimoto round headlight with preassembled aim adjustable mounting bracket set. Installation takes five minutes and the light output is phenomenal.

Low Beam: 2,400 Lumens, 20 Watts
High Beam: 4,300 Lumens, 35 Watts
Color Temperature: 5,000K
Warranty: 5 Years

There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.

You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.

• Plug and Play
• 7 Different Programmable Turn Signal Patterns (for demo video click here)
• Safety Brake pulsing built in (Can Enable or Disable)
• Superbright LED's; For excellent brightness, even in direct sunlight
• License Plate Light built in
• License Plate Bracket fits the common USA license plates, sloted for maximum plate compatibility.
• Includes Mounting Hardware
• Saves about 2 lbs over the factory tail light setup
• Made In the USA

We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.

This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.

This is the brace needed to stabilize the big front fender on the XR650L. This simple bolt-on brace reduces wind buffeting at highway speeds. It also helps carry the weight of a fender mounted tool bag.

Made from laser cut 5052 aluminum, then CNC formed and beautified with a shiny black powder coat. Easily mounts in a few minutes using the included hardware.

Made from strong and light 5052 aluminum to hold your license plate firm and up, out of the way for maximum tire clearance, prefect for your new dual sport bike.

It uses the original tag light with out any modifications to your bike. Mounting hardware and instructions included.

A 5-pack of easy to use disposable funnels to help make any oil or fluid change cleaner and more precise.

JT Sprockets is the world's leading manufacturer of aftermarket sprockets, constantly raising the industry's standards for quality and service. JT Sprockets are the only sprocket manufacturer using the ultra-durable high carbon C49 steel for rear sprockets.

A fresh set of brake rotor bolts. 

Genuine Yamaha OEM bolts work with factory and aftermarket rotors.

Comes in a pack of 6.

Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers

• Knurled anodized aluminum locking ring
• Perfectly weighted to drive seals
• Carbon steel body halves

Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers

• Knurled anodized aluminum locking ring
• Perfectly weighted to drive seals
• Carbon steel body halves

Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.

The three forces of suspension, testing procedures, even the black arts of chassis geometry: This explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.

• Durable 6061 aluminum with blue anodized finish and laser engraved logo
• Used to push the tire bead down into the drop center of the rim on off-road wheels while using tire tools to change tires
• Hooks over spoke and pushes bead down on opposite side of tire from tire irons
• No more fighting to keep bead down while installing off-road tires

This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).

Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.

Maximum master link width 24.8mm.

Will not damage master links, hardened steel pins for reliable use.

Light weight billet aluminum construction.

• PBR = press, break, rivet
• Innovative design will press, break and rivet 520, 525 and 530 chains with one convenient tool (not for use on 428 chains)
• Versatile design will remove chain pins, press master-link plates and rivet hollow nose and soft nose (quad stake) master link pins on O-Ring and non O-Ring type chains
• Easy-to-use design allows you to change tool functions by simply moving the position of the anvil block
• Indexing letters on movable anvil and body ensures correct tool configuration; simply line up the letter on the anvil to the letter on the body to get the configuration you need
• All components conveniently store on tool when not in use
• All steel construction with heat-treated components for strength and durability
• May be supported in a vise or held with included handle
• Great for the professional technician or DIY mechanic
• Compact and light enough to carry in a tool bag for trail-side repairs
• Patent Pending

This kit is for those of you looking for a bit more leg and arm room in the DR cockpit. Included are ProCycle Low Foot Pegs and our oversize bars.

• ProCycle Low Pegs will drop your pegs by 1-3/4" and include wider MX style pegs that are much more comfortable when standing.
• These are not only taller bars, but 1-1/8" at the clamp area for additional strength. They taper down to 7/8" on the ends so all the stock controls fit. Black in color.
• 1 1/8" Warp 9 clamps that raise the handlebar 1".
• A new billet aluminum throttle tube is included.

Each kit includes all necessary rubber components and brake pins.

Have your tank cushions worn out over the years? Have you lost one or more while working on your bike? We have new upper and lower tank cushion rubbers.

This kit includes the original hardware, upper, and lower cushions.

• Stealth license plate vanity light.
• Built-in turn signals.
• Running and Brake Lights.
• 218 LEDs ultra bright.
• 18 white leds. 1.5W max output.
• 200 red leds. 6W max output.
• 12v DC input.

Muc-Off Air Filter Cleaner is a state of the art, professional strength bio-degradeable cleaner that's designed to clean and care for foam filters. Its unique combination of active ingredients is formulated to rip through dirt and oil in seconds, without damaging the foam or glue.

• Specifically designed to be ultra- safe on surfaces
• Helps to extend life of foam and glues
• Suitable for all bikes foam air filters