Search Products

The headpipe gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head, thereby making them a single use part. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.

The muffler joint gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers (Q4 or PowerCore 4) do not require a joint gasket but the all other aftermarket mufflers as well as the stock muffler do require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.

Reduce exhaust leaks with this new OEM exhaust gasket. This gasket goes between the header pipe and the cylinder head.

We recommend Anti-Seize on exhaust fasteners.

Reduce exhaust leaks with this new OEM muffler gasket. This gasket goes between the rear tail/muffler pipe and the header pipe.

Reduce exhaust leaks with this new exhaust gasket. This gasket goes between the header pipe and the cylinder head.

We recommend Anti-Seize on exhaust fasteners.

• Reduce exhaust sound by one to six decibels
• Options for DG V2 & RST and for the older "O" & "R" Series mufflers
• Easy installation; remove rear end cap and place Quiet Core in front of the spark arrestor
• Smaller diameter inserts are quieter but more restrictive; larger inserts are less restrictive but louder
• 1" Not recommended for RST
• Each size is sold separately

Since Kawasaki brought back the popular little KLX250 with updated fuel injection, Yoshimura brought back an updated RS-2 slip-on that now incorporates an o2 sensor that accommodates the new fuel injection technology on the KLX. All of that with added power, torque and that distinct Yoshimura exhaust note.

Entire unit is proudly made in the good old US of A to boot!

• Diamond-shaped sleeve
• Large core and increased muffler packing volume means quieter operation
• Stainless steel cone end-cap
• Stainless steel tail-pipe
• 2.8 lbs. lighter over stock unit.
• Comes with USFS Approved Spark Arrestor

The product that you are purchasing is designed and intended for closed course competition use only and is labeled as such, i.e. Yoshimura "RACE SERIES." Yoshimura RACE SERIES products are neither designed nor intended for use on PUBLIC ROADS or LAND. Such use is prohibited by Federal and State regulations.

No repacking required. The LeoVince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. 

It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed an 84dB sound level using the USFS J1287 testing procedure. That is a bit louder than stock but significantly quieter than other aftermarket mufflers. 

The installed weight is approximately 8.5lbs and it includes a certified Spark-Arrester. 

This muffler requires a stock muffler joint gasket when used with either the stock headpipe or the FMF headpipe.

DG Performance exhausts help your engine breathe better, resulting in increased throttle response, power and torque.

The V2 Series Slip-On muffler features:

• Lightweight aluminum body
• Stainless steel inlet tube
• TIG welded components
• Great new look

Standard sound level is approximately 98 db and quiet core inserts are available separately.

This Lightweight Slip-On weighs approximately 5.5 lbs and bolts directly to the stock headpipe.

It is equipped with a US Forest Service-approved spark arrestor.

No repacking required. The LeoVince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed a 84dB sound level using the USFS J1287 testing procedure. That is a bit louder than stock but significantly quieter than other aftermarket mufflers. It includes a certified Spark-Arrester. This muffler requires a stock muffler joint gasket when used with either the stock headpipe or the FMF headpipe.

This is a genuine Suzuki part. We recommend installing a countershaft seal retainer to prevent the countershaft seal from popping out while riding.

Quality steel sprockets and EK SRO6 O-ring chain. We put them together to make a complete, affordable kit. Chain comes with clip type master link.

• Computer-designed to achieve ultimate strength at minimum weight
• JT combines leading-edge technology with top materials to produce the ultimate quality sprocket range with unbeatable value
• Every sprocket meets or exceeds the highest possible quality standards set for the motorcycle industry
• Sprockets are heat-treated and bead-blasted to reduce material surface tension
• Unless noted, rear sprockets made with top-quality-grade C45 high-carbon steel

Chain guides experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.

The chain slider protects the swingarm from contact with the chain. Replace yours before it wears through to the swingarm.

A set of replacement brake and clutch levers. Standard length.

Please be sure and order the correct levers for your model year KLR.

Note: Gen 1 levers are black
Gen 2 levers are Silver

• Polished aluminum finish
• Quality Aircraft grade A-360 aluminum for strength & durability
• Designed to exceed OEM specifications, built to resist breakage
• Durable hard coating
• Designed to fit OEM perch
• Image is for reference only, actual product may vary for your application

OE style clutch lever.

• Quality Aircraft grade A-360 aluminum for strength & durability
• Designed to exceed OEM specifications, built to resist breakage
• Durable hard coating
• Designed to fit OEM perch

Here's a set of Shorty brake and clutch levers for your 2001 and newer Tdub.

• Black Alloy levers allow two-finger control of the brake and clutch
• Set includes brake and clutch short power levers

A stock replacement brake pedal for the DR650. Nothing fancy but sure gets the job done. Just order it up and get back on the trail. See our Brake Pedal Adjuster Bracket that allows you to adjust the position of your brake pedal to perfection.

One folding mirror. Includes handlebar mount. Can be used on left or right side.

Sold individually.

This new mirror can be folded out of the way when it's time to hit the trails. These are quite similar to the very popular KTM folding mirrors but at half the price.

Fits either left or right side and includes handlebar mount.

Sold individually

With the split back, you don't need to remove your grip or throttle tube, just put it on and tighten 'er down. Put the mirror in and hit the road. Clean and simple.

ProTaper's ADV handlebars give you a bar taller than most with extra space on the control portion of the bar. These bars provide an additional 20mm of space next to where your levers and throttle are located for your GPS, phone cradle, auxiliary switches, etc . They come in Adventure (which is taller than stock) and Adventure High (which is even taller).

These are oversize bars, which means they are are 1 1/8", not the smaller 7/8" diameter. Therefore some bikes will require a adapter and there are several available to select from.

Using the same manufacturing techniques and materials as ProTaper’s industry-changing 1⅛" motocross handlebar, the EVO Adventure is specifically designed to provide adventure/touring riders with the increased comfort and control they need. With over 8" of straight section in the control areas, mounting vital components is made easier than ever. With its premium 7000 series aluminum alloy construction and computer-profiled four millimeter-thick wall design, the EVO Adventure Handlebar is up to 25% lighter and 45% stronger than competing handlebars.

• 1⅛" tubing at the clamping area
• Exclusive 4 mm-thick 7000 series aluminum alloy for superior tensile and yield strengths
• Optimum balance between fatigue life, impact strength, and impact-absorbing flex
• High-tech shot peened, stress-relieved, and anodized finish for unmatched durability
• Independent lab tests show that the EVO Handlebar leads the market in fatigue life
• Epoxy inner coating resists corrosion
• Chemically applied cut lines and alignment grid are scratch- and peel-resistant
• Plastic bar end plugs keep the elements out and provide a stronger base for grip ends
• Weighs only 1.55-1.7 lbs. (720-780 grams), depending on bend

These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!

Included in this kit are the parts needed to repair a second generation TK carburetor. You get a new float bowl gasket, needle valve with O-ring, needle, mixture screw, and stock jets for the '01-'26 models kits.

This kit is for the 36mm Mikuni CV carburetor and includes 2 Needles that have been developed by JD Jetting and manufactured for them to their exacting specifications. These two needles allow a wide range of tuning possibilities and provide correct fuel delivery at any throttle position.

4 allen type screws for the top of the carburetor are also enclosed should you strip out the stock screws during your tuning process. Complete instructions with photos, jetting suggestions for different set-ups and situations, 5 Main Jets, a Pilot Jet and a drill bit complete the package.

• Includes all necessary parts to rebuild the OEM fuel pump module
• Restore lost performance or non-functioning fuel pump with this economical solution
• Kit comes ready for plug-and-play installation

Zero Gravity windscreens feature the finest optics of any windscreen on the market. All Zero Gravity windscreens are fabricated using highly specialized "vacuum forming" techniques similar to those used to form aircraft canopies. The result is a virtually distortion free optical lens.

Made from the finest grade of acrylic plastic, Zero Gravity windscreens are stretched as they are formed, a process which results in superior strength and flexibility. This flexibility allows the windscreen to absorb road vibrations and resist cracking. All of our windscreens are factory pre-drilled and ready to install. The mounting holes and windscreen profile match the O.E.M. windscreen for a precision fit.

Zero Gravity currently offers three types of windscreens for the new version of the KLR.

SR is the Stock Replacement

DB is the Double Bubble screen

ST is the Sport Touring model.

The DB model is approximately 1.75 inches taller than stock and the ST is approximately 3.5 inches taller than the original. Each screen is available in Clear, Smoke or Dark Smoke colors as well.

The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.

This windscreen mounts securely to the three stock windshield holes as well as the two side cowling mounts. The shield is 14 inches tall, 13 inches wide at the bottom narrowing to 11 inches at the top. Made from 3/16" military aircraft grade cast acrylic.

Transform your ride. Now there is wind protection for on and off-road use with no compromises! MadStad's new rotating dual-sport windshield brackets put the windshield where you need it for street riding, but tuck it down out of the way for off-road. Adjust the height and angle for much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide, and it's not in your face when you want to hit the trails.

Their complete drop-in system is custom-made for your bike and includes everything needed to mount and position the shield. Your bike will not require any modification.

What's included in the kit:

• A set of MadStad dual-sport adjustable brackets
• 3/16" (4.5 mm) thick cast acrylic windshield

The MadStad brackets bolt to your fork clamps putting the windshield just in front of your instrument cluster for street riding, with adjustability for height and angle. The rotation feature allows you to shift the shield forward and down through 7 different settings bringing it down in front of the head light and out of your way. Their custom knobs lock the brackets in their multiple positions so the shield stays where you want it to, even bouncing around off-road.

Molded using a very durable, lightweight 1/8" thick polycarbonate - giving the windshield a high impact strength and making it shatter-resistant with a superior light transmission quality. Mounts quickly and easily onto the stock headlight cowling for a clean factory look. Drilling of the cowling is required, hardware is included. Removal for trail riding is also quick and easy.

Factory Replacement Body Plastics from Kawasaki

Genuine Suzuki super moto fender. A perfect match for the original gray plastic.

Left and right stock OEM Suzuki side panels plastic sold as a pair.

Includes one heat shield. Depending on your application and preferences, more than one heat shield may be useful. Extras can be added here.

• The distinctive look of Acerbis is everywhere
• OEM color-matched for direct replacement or works look
• Pre-drilled pieces mount easily to stock locations
• Radiator covers and side panels sold in pairs

OEM Suzuki headlight cowling.

High-quality, direct replacement plastic kit includes:

• Front and rear fender
• Side covers
• Air box cover
• Radiator shrouds

Yellow kit is only available with white side covers

  Add-on Headlight cowling fits S and SM models not "E" offroad model

Includes forged JE 89mm piston 10.5:1 piston, Rings, Clips, Pin, big bore sleeve and top end gasket set. You will have to have the big bore sleeve installed in your cylinder and bored to fit the larger piston.

The PSR Oil Filler Caps are CNC machined from high quality aluminum and come with an E-clip that is already safety wired to a mounting tab. The wire is covered with silicone tubing that will not melt or discolor. Available in silver, black and gun metal.

New starters that are manufactured to meet or exceed OEM specifications. Pull out your old starter, put in this new one and go riding. These units are built to provide a longer life than the OEM unit with these features:

• The armature is insulated for rust and corrosion protection
• Rubber seals on the top and bottom of the unit ensure a dry operation
• 90/10 copper bushings
• Extended shaft replaces long or short shaft OEM starters

CNC machined oil filler cap with locking clip to keep it in place in the roughest conditions. The cap is pre-drilled and the locking clip is safety wired to the mounting tap with a section of silicon tubing, that will not melt or discolor, over the wire. First class all the way. Available in Silver, Black, Blue or Red.

• Precision-machined from 6061-T6 aluminum
• Simple positive installation with an Allen wrench
• Set of two plugs (unless noted) replaces the stock plugs
• Polished to a mirror finish prior to anodizing, resulting in a brilliant look
• Anodized finish
• Made in the U.S.A.

Bolt on horsepower! Stage 1: single-cam motor. Excellent midrange and top-end power increase. Uses stock valve springs and rockers.

Fitment Specs: Exhaust Lift: 5.9; Exhaust Duration at 1.00mm: 223°; Intake Lift: 6.8; Intake Duration at 1.00mm: 227°

Keep your motor running right with fresh spark plugs!

NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.

• High-quality materials and superior construction for serious power and reliability
  • Pure alumina silicate ceramic insulator provides high strength and better heat transfer
  • Deep-seated copper core for a wider heat range
  • Nickel alloy tip for longer life
  • Trivalent metal plating provides superior anti-corrosion and anti-seizing properties
• Choosing the right high-quality plugs prevents fouling from running too cool and preignition from running too hot
• NGK plugs available for almost every application and riding style

• The Core Manual TorqDrive clutch delivers unprecedented performance, tuning and durability
• TorqDrive provides more disks in less space, allowing up to four additional friction disks over stock
• More frictions = more torque capacity, thus unlocking the full power of your engine without the need to add stiffer pressure plate springs
• Provides more consistent clutch lever feel and behavior
• Can be set up to maintain a stock, or lighter than stock, lever pull depending on engine tuning
• Rekluse sleeves eliminate basket wear and notching
• Proven in racing at the highest levels
• Made in the U.S.A.

Billet plugs for your left side case. 

Includes both the timing mark plug and the crankshaft access plug.
 

Fits Moose and other aluminum hand guards

• Aerodynamic and stylish design
• Protect hands from brush, water and cold wind
• Simple installation
• Sold in pairs

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!

The Complete Seats come assembled with an aftermarket pan and ready to ride.

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

Complete seats are built by Seat Concepts on a new seat pan and come ready to be installed on your bike.

These wider seats from Seat Concepts help keep you comfortable on those long commutes or dual sport rides. The added width and improved foam density help keep your seat from being the item to stop you from going on those big rides or enjoying the bike.

The Complete Seats come fully assembled on an aftermarket seat pan, and are ready to install and ride.

This is a high-quality seat cover kit by Moose for the XR650L. This is a direct replacement seat cover only. No seat foam, and you install on your stock pan with existing foam. Heavy duty marine grade vinyl, and UV protected for long life. Double stitched for durability. Available in Red or Blue.

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

These wider seat kits from Seat Concepts keep you comfortable on those long commutes or dual sport rides. The added width and improved foam density will help keep your seat from being the item to stop you from going on those big rides or enjoying the bike. 

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.

These grips feature a thicker design that dampens vibration. The soft shoulder allows ease of movement. Three wire-tie grooves are molded into the grip to make securing them a breeze. We think they are great!

• Engineered to keep your chain clean and lubricated under the harshest conditions
• The triple action formula cleans, lubricates and protects your chain - no matter if it's a standard or O-ring chain
• Engineered to adhere to your chain, on or off-road, and lasts long during those epic adventures
• The biodegradable solvent carrier helps clean chain and aids delivery of oil to micro-pores in chain
• Biodegradable oil penetrates and adheres to metal for an efficient, long-lasting lubricant
• Biodegradable wax seals in oil and keeps dirt off of your chain
• Biodegradable and non-toxic
• Available in 12-ounce (EU: 354,88 ml) aerosol cans

• Innovative multi-use tire tool set
• Breaks the bead on most street and off road motorcycle tires
• Integrated tire spoon for tire removal and installation
• Light weight and compact size is perfect for tool packs
• Ergonomic handles with crossguard to keep hand from riding forward
• Forged 7075-T6 aluminum construction for strength and durability
• Black anodized finish
• Patent pending

Available in 9.5" aluminum (ideal for travel) and 16" forged steel (useful in a home shop/garage)

Protect your wheels from scratches and dings caused by tire changing tools.

• Includes retrieval cord for easy use
• Sold in pairs

• Eliminates the need to cut and splice wiring when using aftermarket turn signals or marker lights
• Plug into the OEM turn signal plug and then use bullet style connectors used on aftermarket lights
• To verify proper fitment, compare connector photos to OEM connector
• Sold in pairs

The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.

You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.

Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.

There are many options and configurations using this electronic tool.

No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.

• Stop your expensive helmet from falling and hitting the ground while you’re out riding
• The perfect solution to easily store your helmet with your bike.
• 7075 T6 machined aluminum
• Fits all 7/8 handle bars
• Includes 2 stainless screws
• Fits virtually all bikes and makes ( except Harley )

A premium billet sprocket carrier from Warp 9 Racing that houses 2 bearings to help protect against the sideways twisting load that is commonly known to prematurely wear out the bearing and cush rubbers. This wear can cause extreme failure possibly damaging the hub.

Anodized, Includes spacers already installed.
Stock sprocket bolt pattern to fit any stock compatible sprocket.

These are designed to work with Warp 9 and OEM hubs.

Includes all wheel bearings, new dust seals. The rear kit includes the bearing and seal for the cush drive hub (sprocket carrier). All bearings are sealed on both sides.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Rear wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

A fresh set of brake rotor bolts. These bolts already have thread lock compound applied to the threads.

Stock OEM works with factory rotors, comes in a pack of 6.

For aftermarket rotors like Warp 9 or EBC front and rear sets are available.

Front comes in pack of 6
Rear comes in pack of 4.

Chain guards experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.

The GCAG Mount Point is a sturdy piece of hardware to make it easy to attach soft luggage and straps to your motorcycle or any vehicle. Made of stainless steel, it will never rust and its strong enough to hold any luggage you care to throw at it.

Sold individually.

SUGGESTED USES:

• Soft Rack Side Strap - Use as an anchor for your GCAG Soft Rack side straps
• Pannier Anchors - You can add these to your hard boxes as attachment points for straps and bottle holsters.
• Dirt Bike Anchors - You can drill dirt bike plastics and add hard mount points for straps, bottle holsters, and luggage systems.

FEATURES:

• Stainless Steel - Never worry about rust or strength.
• Laser Etched Logo - No cutouts to weaken the hardware.
• Solid Slot - The webbing slot has no slits or cuts. This keeps the mount strong and makes it impossible for your straps to slip out on accident. The opening has plenty of room to make it easy to work with. 
• Customizable - We left enough room for you to drill an additional hole if you want to. This could be helpful if you want a smaller hole for your mounting purposes.
• Universal Fit - You can use this with any product you have. The slot will easily accommodate 1" webbing or smaller. Additional hardware is not included. 

DIMENSIONS:

• Length 2" (50mm) x Width 2.75" (70mm) x Height 1/8" (3mm)
• Slot Width 1 1/8" (28mm) x Height 5/16" (8mm)
• Hole Diameter 3/8" (10mm)

Here is another great upgrade for the TW200 or the VanVan front tire.

Universal 'old school' trials type tread pattern. A versatile performer with a tough nylon carcass and raised dimpled knobs that work well in a variety of terrain.

• Narrow knobby configuration means less of an environmental foot print on the trail
• 4 ply rated
• DOT approved
• Not intended for extended highway use

Tire size is 4.00-18 (64P load / speed rating)

• Lighter and stiffer than stock, high quality shock spring.
• A proper rear spring will give a smoother more controlled ride.
• Available in a multitude of spring rates, one is the perfect fit for your bike and riding style.
• Stock spring is rated at 5.3 kg/mm for the CRF450L

Complete kit to replace the bearings and seals in the XT225 swingarm pivot.

Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes fork seals and dust wipers.

This high quality socket from Motion Pro, is specifically designed to reach into the very small, deep space where the spark plug of the XR hides.

Normal sockets simply won't work in this case.

Replace those worn out brake pads with quality EBC replacements.

• The perfect brake pads for leisure use
• Offer maximum durability and excellent braking performance
• Constructed of U.S.-made sintered bronze for longest lifetime
• Best for riding in water, mud, dust, or sand

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand

This frame includes six, white, full-spectrum LED bulbs on a 6-inch strip for bright illumination of your license plate. It is made in a sturdy cast aluminum, and is powder coated with a durable black finish.

Outside frame dimensions are 7.25" in. wide by 4.2". Center to center mounting hole distance is 5.7 in. All mounting hardware is included.

Here is an adjustable height centerstand from T-Rex Racing. If you are running supermoto wheels or lowering links, this centerstand will be much easier to use.

T-Rex stands are made from steel tubing finished in black powder coating for durability. Back by a 3-Year limited warranty for any material or manufacturing defects. Rest assured that you are getting best material commercially available.

Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools.

Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.

This set of high quality replacement steering stem bearings includes:

• Upper and lower tapered bearings
• Upper and lower bearing races
• Upper and lower seals

Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".

Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".

Designed to seal completely around the cable housing and stop all those messy leaks. With the unit closed and sealed around the cable, your cable gets better lubrication and you waste less lubricant.

• Works on most cables with a 4mm - 8mm O.D. housing.

All that you need to repair and inflate your tire on the road or trail.

• Padded nylon zippered carrying case easily stores inside fanny pack or tool compartment
• Everything needed to repair and inflate tire on the road or trail
• 4" inflator hose accepts threaded cartridges only
• Each cartridge produces 8-9 psi
• Made in the USA

Kit includes:

• 1 - large oblong patch
• 2 - medium size patches
• 3 - small patches
• Thumb buffer
• 0.50 oz tube of rubber cement
• 5 - 4" rubber insert strips
• Insertion tool with screwdriver handle
• Reamer/rasp tool with screwdriver handle
• 3 - 16 gram 3/8" threaded CO² cartridges
• CO² 4" inflator hose

CO² cartridges cannot be transported on an aircraft.

Warp 9’s Pro Rim Locks are developed with Ice Track, Dirt Track and Flat Track Racers in mind!

Burnt Titanium Main Bolt

Lightweight Forged Aluminum Body

Black 7075 T6 Tower Nut and Base Washer

Base washer is machined to match each specific rim curvature for a perfect fit

About half the weight of OEM rim locks!

1.60 front  – 1.8 oz

1.85 front – 2.0 oz

2.15 rear – 2.3 oz

2.50 rear – 2.7 0z

3.00 rear – 3.10 oz

The high rigid and light weight design, provides better control of the rear brake. Clevis body is made of A7009-T6 aluminum. Comes with a specially designed stainless steel pin.

A replacement Clarke Gas Cap that fits most Clarke Gas tanks. Comes with rubber gasket.

Simple, lightweight rack made from rugged 1/8" 5052 Aluminum, with a rigid 5-point mounting system.

Low profile allows for easy seat removal.

Features:

• 12" long by 10" wide
• Integrated turn signal mounts
• 16 strap slots for securing cargo
• RotoPax mounting kit compatible
• All hardware and instructions included

Note: Placement of this top rack does require removal of the stock tool bag.