Is the cylinder head intake boot on your DR650 cracked or weathered, is it missing parts of the lip to seal around the carburetor, have you recently pulled the intake boot off only to realize the O-ring behind it is hard & brittle? This kit is your solution to solving some of those mystery problems and make your bike like new again. There can be a great deal of heat that can radiate behind the cylinder head on a DR650 as it is an air cooled engine. With that comes long term maintenance items that will need to be replaced due to them being made of materials that cannot withstand those constant heat cycles indefinitely.
Our kit includes O.E. parts from Suzuki to include:
Hiflo filtro air filters are manufactured to fit the factory air box and are a direct replacement for original equipment filters. Top quality powerflow filtering media, developed for modern high performance engines.
Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.
Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.
The cush hub (sprocket carrier) bearing leads a tough life. This is especially true if your cush rubbers get old and soft. They can allow the chain to pull the cush hub sideways putting a twisting load on the bearing. If there's any question about the condition of your bearing replace it now with this double sealed bearing and quality seal.
The headpipe gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head, thereby making them a single use part. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
The muffler joint gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers (Q4 or PowerCore 4) do not require a joint gasket but the all other aftermarket mufflers as well as the stock muffler do require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.
Universal fit. May require additional adjustment or modification.
Have you lost your stock heat shield, or need one on an aftermarket head pipe? FMF makes this nice unit that includes clamps, heat shield with the FMF logo and button head screws to hold it on. We recommend Anti-Seize on all exhaust fasteners.
The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.
Uses long-life muffler packing for increased packing life
The RS-2 is a potent and versatile design that evolved from their original TRC, engineered to provide increased power delivery. With a different pyramidal shape that features increased volume, the RS-2 is a quieter system with a larger core — and it offers the added bonus of outstanding performance in a value-priced package.
Diamond-shaped sleeve
Large core and increased muffler packing volume means quieter operation
Akrapovic has spared no expense with this titanium body and end cap with stainless steel mid pipe slip-on muffler. If you want the best in quality for your Tenere 700, look no further than this muffler. Complete with everything that you need to install and a removable sound insert for a more quite commute.
The latest EVOLUTION of the popular LV ONE: aggressive sound and style
Clean laser-etched Leo Vince logo in an innovative carved design (for the carbon fiber exhaust: bright aluminum die-cut high-temp resistant Leo Vince adhesive logo)
Asymmetric design and high-tempiresistant full-carbon fiber end cap
The PSR Oil Filler Caps are CNC machined from high quality aluminum and come with an E-clip that is already safety wired to a mounting tab. The wire is covered with silicone tubing that will not melt or discolor. Available in silver, black and gun metal.
The unique design of the electrode maximizes the power generated by the spark plug through Diamond Fire technology. This electrode combines advanced performance capabilities and innovative technology to enhance the shape of the flame kernel. Consequently, the flame front ignites the air/fuel mixture more rapidly, accelerates heat transfer into the combustion chamber, and creates a more concentrated pressure front, facilitating a quicker pressure rise during the cylinder power stroke. The outcome is a more efficient combustion process and improved engine performance, making this a truly premium spark plug.
This kit provides much of the performance gain of the more expensive 150 (143cc) kits. But gives better reliability due to the thicker wall of the cylinder sleeve.
Wiseco 55mm high compression 11:1 piston, rings, wrist pin, and clips
HotCams stage 1 performance camshaft
Includes top end gasket set
Requires cylinder to be bored to fit the larger piston
Complete set of friction plates, HD springs and steel separator plates prevent premature driven plate wear, oil muddying and loss of stack height. Built with swaged aluminum carriers that spread the load on the clutch basket and prevent clutch basket "dogging". Anti-swell, alloy impregnated heavy-duty cork-based facings for smooth clutch take-up. Allows modulation, unlike paper clutches which tend to snatch.
The original Hiflofiltro factory was founded in 1955 and has been manufacturing filters for the OEM motor industry since 1963.
Constructed using the best materials available.
With the experience of more than five decades, constant research and development and featuring a completely modern production facility, Hiflofiltro offers some of the best quality filters in the world.
TUV approved and production monitored to ensure OEM or better quality.
Universal fit. May require additional adjustment or modification.
A complete kit to mount your phone (or other electronic device) to your motorcycle. The universal cradle expands from 2.25" to 3.25" wide and 4.75" to 6.25" tall. The width is adjustable but fixed while the upper portion of the cradle is spring loaded to keep your device secured in the roughest conditions.
Select the mount option that works best for you. The mirror mount is shown in the photo at left and is a flat plate with an 11mm hole on one side and a RAM ball on the other. Simply remove your mirror, place the plate between your mirror and the perch and tighten it down.
The handlebar mount kit allows you to mount to either a 7/8" or 1-1/8" bar. Also includes hardware to mount to the back of a lever perch. See image at bottom middle for kit pieces.
The X-Grip with handlebar mount is best suited for larger phones up to 4.5" wide. The spring loaded X-Grip cradle expands and contracts, allowing for a perfect custom fit. Kit also includes a device tether recommended for outdoor applications.
Universal fit. May require additional adjustment or modification.
Looking for motorcycle road trip ideas? How about a Backcountry ride? Each of our backcountry motorcycle maps highlight the official Backcountry Discovery Routes (BDR) taking you off-road through some of the most spectacular scenery in the United States.
T700 TENERE Bash plate was designed to withstand the harshest Aussie conditions. Bash plate is made from 5mm structural thick alloy plate and designed for maximum protection with minimum bulk.
Easy to mount and remove. Also includes a replaceable polyethylene linkage guard.
Enjoy maximum protection and durability with an SW-MOTECH skid plate. Fully welded aluminum construction is engineered in Germany to provide proper protection from impacts, abrasions and projectile debris. Multiple ventilation slots on the front, sides and bottom of the skid plate permit maximum air-flow to keep your motor cool. Drilling, cutting, welding or any other permanent modifications are not required.
Features:
Debris and collision protection for the engine
Fully welded 4mm thick aluminum plate / black side made of 2.5mm thick aluminum
Efficient underbody protection of stone-chipping and collision
Provides protection for the vulnerable oil pan & lower engine cases
100% bolt-on, no drilling, cutting, or any other permanent modifications needed
Ventilated design maximizes air-flow to prevent overheating
The SW-MOTECH Rear Brake Master Cylinder Guard is designed to fit the Yamaha Tenere 700. This guard protects the rear master cylinder from impact and prevents the foot from contact. A laser-cut and precision bent aluminum strengthening process makes the construction tough and durable and capable of withstanding heavier blows.
Features:
Prevents contact between boot and foot brake cylinder and provides additional protection
Provide protection for your motorcycle’s front brake and clutch levers with Barkbusters aluminum bar lever protection handguards. Designed specifically for the Tenere 700, these guards feature heat treated full wrap aluminum backbones that mount at two points on each side for strength. Prevent costly damage to your motorcycle with Barkbusters aluminum bar lever protection handguards.
Features:
Two mounting points provide secure protection
Full wrap guards
Heat treated aluminum backbone bars
Easy installation
Compatible with all Barkbusters deflector guards (not included)
Adventure bike heaven is off-road headed down a dirt road or a trail. If that is your dream, then as you know, you are going to fall. Sometime, someplace, it will happen, so be prepared! Save your bike before it happens.
SW-Motech makes some of the finest protection equipment available. The set-up for the Twin is available in a standard black powder coating or a semi-polished Stainless-Steel tubing. Both sets will protect the vital components of your motorcycle as well as you from damage incurred during a fall, slide or crash. They will preserve the frame, radiator, bodywork and other critical components from touching down with robust tubular steel. The black kit uses 27/21 mm tubing while the Stainless uses straight 22 mm tubing throughout.
Both configurations have a tight fit for great ground clearance and are designed to work seamlessly with other SW-Motech products like their Skid Plate/Engine Guard and SW-Motech Hawk light mounts. Three secure mounting points per side provide the necessary support that make these so strong. There is no drilling, cutting, welding or any other modifications required for mounting but still allows access to the oil filler, tool box and battery. Kit includes all necessary hardware and instructions and an aluminum cover to replace the OEM plastic cover at the lower mounting point on the left side.
Please Note that these Crash Bars are also compatible with the SW-Motech Skid Plate and the SW-Motech Centerstand.
This durable, steel crafted SW-MOTECH Upper Crash Bars Engine Guard protects the tank, fairing and radiator of your Tenere 700 from damage caused by either debris on the road or a crash.
The tough-built, steel constructed bars can ONLY be mounted with SW-MOTECH Lower crash bars (sold separately).
Each engine guard is powder coated black for a sleek finish which remains durable after prolonged use and protects against corrosion caused by the elements.
These low peg mounts will drop your footpegs 1.5" and move them to the rear 1" for a much more comfortable riding position, especially for taller riders. Unlike relocation plates, these mounts do not hang dangerously below the frame. You can mount stock or aftermarket pegs and they are compatible with all skid plates, crash bars, and center stands.
New 10.9 high strength mounting bolts are included. Once installed the foot controls will need adjustment and the brake switch spring will need to be slightly modified.
Made from 1/8" thick stainless steel with dual folded edges for additional strength, these brackets will relocate your passenger pegs down 4" and move them back 1.5". This will give your passenger additional legroom making two-up riding much more comfortable.
All hardware is included for a quick and easy installation.
Low peg mounts from JNS Engineering. Your choice of a straight 1.5" drop or get that drop and a 1" rearward offset. You can use your stock pegs or click on one of the optional pegs that are made to fit the stock DR650 mounts.
These heavy duty steel mounts are pressed, welded and then powdercoated black for protection. Includes mounting bolts.
Note: These mounts are compatible with the SW Motech Center Stand by adding a 1/8" spacer behind the mounts.
Our complete foot peg assemblies. 1-3/4" lower than stock. No extra brackets that hang down below the frame. Easier on the knees. Wider platform Yamaha YZ style footpegs are stronger and give you firmer footing. Mount solid to the frame. No more 'droopy' feeling when standing on the stock pegs. Lowering your footpegs makes it easier to stand and less of a reach down to the bars when standing.
Now you can get our Low Pegs with MK4 Pivot Pegz or black Fastway ADV pegs (both Yamaha YZ pegs) installed!
This kit combines common wide platform Yamaha YZ/WR foot pegs with brackets that are custom made to fit the TW200. If you are tired of standing on the stock skinny footpegs, get yourself a set of these fat boys and have pegs that match the tires on your T-Dub! For ultimate comfort, order the Pivot Pegz kit!
Simply unbolt your stock brackets and bolt these in their place. The bracket on the right side (brake lever side) is shorter than stock to correct the offset in the stock pegs. On kickstart models, the stroke of the kickstart lever is shortened slightly. Should you ever need to replace the pegs in the future, simply order pegs for the Yamaha YZ or WR 250/450.
This is the ultimate adventure bike platform, it measures 2.25" wide, 4.75" long.
Patented adjustable collars make it easy to run them in the stock or lowered positions on most bikes.
Gain more room for bulky boots, or for longer legs. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long. Kamber bolts lets you adjust the 'tilt' of your pegs to increase comfort, or to give better squeeze on your bike.
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty. Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever!
Wider, lighter, stronger design
Widest (mm) and lightest pivoting pegs on the market
The SW-MOTECH center stand for your Yamaha Tenere 700 increases the versatility of your machine for more secure parking on various terrain while enhancing ease of maintenance. Robust steel construction provides sturdy support for the motorcycle and is powder coated black for enhanced durability and corrosion resistance. This high quality center stand is designed and engineered in Germany for seamless integration with the factory original components and easy operation utilizing a built in foot lever which increases leverage and decreases lifting effort.
Features:
Robust steel construction
Attractive powder coated black finish adds corrosion resistance & durability
Improves parking stability and versatility on various surfaces
Significantly reduces the risk of a tip over when used on softer terrain vs side stand
Integrates perfectly with the factory original components
Easy to use German design uses leverage to make lifting a cinch
Foot lever increases leverage to aid in lifting technique
Does not require cutting, drilling or any other permanent modifications
Allows on the road maintenance without a paddock stand
Eases chain and tire maintenance
Double retention spring ensures safe operation even if one spring fails
Universal fit. May require additional adjustment or modification.
The Battery Tender® Junior Selectable is much more than a trickle charger. It has a brain. It's lightweight, compact, and fully automatic; very easy to use, especially in small spaces. It will keep your Lead Acid, AGM or Lithium battery fully charged so that it is ready to go when you are
Output: 12v @ 800mA
Selectable Battery Chemistry- has battery chemistry selection with proper charge algorithm for lead-acid, flooded or sealed maintenance free (AGM and gel cell), and Lithium Non-RS/Non-BMS batteries
Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position. There is no hazardous acid or heavy metals, it is non-explosive and non-combustible.
The Firepower features Increased cranking amps over lead acid batteries and has a very fast recharge cycle and can be brought up to a 90% charge within 6 minutes and also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.
Rated at 250 CCA (Cold Cranking Amps) Package Dimensions: 6.20 x 3.70 x 4.80
Antigravity Batteries introduce the ground-breaking "RE-START (RS)" line of batteries. These are the first batteries with built-in jump starting! They intelligently monitor their status, and just before going completely dead, puts itself to sleep with just enough energy to get your vehicle started again. Simply press the RE-START button located on the battery, then start your bike and ride away!
These are an extremely lightweight (2.3 lbs.) and high-powered Lithium-Ion replacement battery for motorcycles. These batteries offer the first Battery Management System (BMS) found on a powersport battery and includes low-voltage cut-off, over discharge, over-charge, and thermal protections with real time lithium-ion cell balancing. Highly recommend using a lithium charger to maintain the life of the battery.
3 Year warranty
Product Size is just 5.9"L x 3.5"W x 3.74"H. If you need spacers, select the optional Foam Kit to pad the battery in the battery box.
New from Warp 9, a full floating 320mm Supermoto disc with caliper relocation bracket! These rotors have an additional hole for placement of a magnet for an electronic type speedo like the Vapor.
GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Significantly improves response and feel over factory rubber lines
Largest performance improvement for your money over any other braking upgrade
Stainless steel hose resists abrasion and puncture
Teflon core does not degrade over time like rubber lines
PTFE Dupont 64 Teflon® hose
Feature a heavy-duty stiffener sleeve and route just like the factory lines
Proprietary, premium fittings
Banjos utilizes a unique machined channel and sealing surface for leak-free installations
R&D and engineered in the USA
GBrakes USA controls the manufacturing process, ensuring the highest level of quality control
Helps protect vulnerable fork tube and seal from dust, dirt, and corrosive elements. These are sewn into a tube and require that you drop your fork tubes down out of the triple clamp for installation. Can still be slid up for easy cleaning.
32 mm-43 mm Diameter 127 mm (5") Length 3 mm Thick
Cogent Dynamics Mojave product is a drop-in replacement for the DR650 stock shock, no modifications necessary. Mojave is not simply an improved Suzuki shock, it is a brand new replacement shock that is a totally engineered suspension solution to suit your needs.
Each shock is assembled and tested on the Cogent Dynamics suspension dyno before being packed up and shipped. Like its bigger brother the Mojave Pro Series, this will make an incredible difference in the handling of your DR.
Mojave Improvements over stock Mojave upper mount: uses a precision spherical bearing with dust seals, which accurately transfers damping forces to the motorcycle frame.
Internal improvements: Cogent designed shaft, seal head, damper piston, adjuster and clevis. Mono tube construction: precision honed, super-stiff steel body with an upper body cap machined from billet aluminum. Built-in billet aluminum separator piston provides an in-line gas pressure reservoir which eliminates the Suzuki rubber bladder.
This shock package includes the CNC machined Bling Ring Preload Adjuster Collar and Preload Bearing that will make preload adjustments easy.
Select the spring you want installed based on the load you plan to carry. For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring. If you regularly have more than 250 pounds the bike, you might want to use the 8.15 kg/mm spring. If you have any questions at all about this, please call.
You may choose to add the Hydraulic Preload Adjuster to make it the easiest of all. All you do is twist the knob. Includes mounting bracket for knob unit. (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)
Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.
The Modoc 250 replacement rear shock significantly upgrades your Yamaha XT250 suspension. Cogent Dynamics custom build this high quality and high performance shock to suit your riding needs.
Optimized damping rates to give you the best ride comfort, traction and control.
Frequency and velocity sensing valving works great over wide ranging conditions.
Rebound damping adjustability.
Low internal friction.
All CNC machined components for top quality and performance.
Compact and rigid design with internal separator piston.
Fully serviceable shock is designed for the long haul.
Cogent Dynamics build a fully custom suspension component, just for you. To best meet your needs, please spend a few moments providing us with your riding style (off-road / adventure, or street / commuting) and your approximate weight with gear and luggage in the comments during checkout. The information you provide helps them setup your suspension to most closely meet your needs.
Specifications for the Modoc 250:
Fits: Yamaha XT250 from the new models introduction in 2013 to present.
Rebound: Over 30 clicks of adjustability
Spring Preload: Single threaded collar for ease of adjustability
High Quality Replacement Wheel Bearings and Seals for your TW200.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
JT steel rear sprockets are manufactured using only the finest grade of C49 high carbon steel.
Two styles of rear sprocket were used on the DR350. The 90-95 'S' and 'SE' (street legal) models have a cush drive hub. The 96-99 'S' and 'SE' as well as all of the 'dirt only' models have a non-cush rear hub. Select your sprocket accordingly. If you are not sure, look at your bike. If the sprocket is bolted directly to the wheel hub you have a non-cush model. If your sprocket is bolted to a separate sprocket carrier you have a cush drive model.
Universal fit. May require additional adjustment or modification.
The Mojave Series LED Racing Lights have been designed to survive and operate in extreme conditions. Lights feature a heavy duty housing that can withstand hard impacts and a lens that is twice as thick as traditional lights. The light includes three different replaceable lens (Flood, Spot, and Combo).
Features:
Heavy Duty Design
IP69K Rating
Flood, Spot / Flood, & Spot Lens Included
Stainless Steel Bracket & Hardware
5,000k Light Color – Natural Daylight
Heavy duty black steel left & right mounting brackets to bolt directly to your lower triple clamp.
Harness with Switch
This kit will work with the 6.6 Gallon Acerbis fuel tank for the DR650. You must run the light brackets inwards in order for there to be proper clearance with the 6.6. Gallon tank.
Kit includes:
2" x 3" LED light pods @ 2,000 Lumens each.
Harness with switch and mounting bracket.
Left & Right mounting brackets with 4 lower triple clamp bolts.
This heavy duty aluminum bracket is specifically designed for mounting auxiliary LED lights to the front of your XR650L without interfering with your large aftermarket fuel tank. If your bike needs improved lighting this mount is the best place to start!
– 0.190″ 5052 Aluminum – Laser cut – CNC formed – Powder coated black – Includes stainless mounting hardware and JNS stickers.
The long over-due rally shield for the 2008-on KLR650 is finally here!
Parabellum uses 4 steel brackets mounted to factory locations as well as our stand-off windshield design to ensure the customer doesn’t have to drill extra holes in the cowling but still achieves that iconic upright look of the real Dakar Rally bikes.
The Rally shield protects the rider’s torso/chest from air, cold, roost, branches and bushes while leaving the rider’s head/helmet in clean air. We recommend the Rally shield for riders seeking some protection, but prefer to be off-road.
The Rally shield is made from 1/8 inch cast acrylic and is 11.5 inches wide at the bottom and 17 inches tall.
Universal fit. May require additional adjustment or modification.
Innovative anchor knot attachment system with an anti-slip cam buckle system that allows you to install or uninstall the bag quickly. Quick-release mounting system with adjustable hook-and-loop straps and an under-seat center strap.
1200-denier Technolast UV-treated polyester construction
Comes with a 100% waterproof rain cover
Expandable rain covers included
Measure 14" L x 5.5" W (expandable to 9.5" W) x 10" H
Universal fit. May require additional adjustment or modification.
Every backcountry adventure-seeker needs a handful of these multi-purpose straps with virtually unbreakable fasteners. Each pair of stretch polyurethane Pronghorn Straps™ feature stamped aluminum buckles sheathed for scratch protection with arrows that line up for easy fastening. Each buckle prong holds the strap in place for pre-fitting and easy chaining of straps together.
Available in color-coded 18-, 25- and 32-inch lengths and marked by size, you’ll find a million uses for Pronghorn Straps—motorcycle, sled, snow bike, 4×4, ATV, UTV/SXS—and so much more!
18” L x 0.75” W (46 cm L x 2 cm W); length adjustable from 6.5″ to 15″ (17 cm to 38 cm)
Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.
The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary har
Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets and that will be no problem. See bottom image.
Note: Placement of this top rack does require removal of the stock tool bag.
T7 Solo Carry rack has been designed predominantly for the solo rider to keep loads as forward and low as possible. The plate has multiple attachment points making easy to tie down bags.
The plate is pre-drilled for mounting systems for both Givi monokey and Rotopax. The rack is light in weight only weighing 2.3kg.
Fits with standard seat only. Will not fit with Rally seat
Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 3 strong powder coated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approximately 13" long.
You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.
Universal fit. May require additional adjustment or modification.
Shinko 700 Series tire features an aggressive 60% on-road and 40% off-road read pattern for good dirt riding performance, without sacrificing pavement grip. Other features:
Aggressive tread pattern with drop lug construction
Yamaha mirrors have reverse threads on the right (throttle) side of the handlebars. This adapter allows you to mount a mirror with standard 10mm threads on the right side of your handlebar. This opens up many options for your mirrors, choose any 10mm mirror for your Yamaha.
ProTaper's ADV handlebars give you a bar taller than most with extra space on the control portion of the bar. These bars provide an additional 20mm of space next to where your levers and throttle are located for your GPS, phone cradle, auxiliary switches, etc . They come in Adventure (which is taller than stock) and Adventure High (which is even taller).
These are oversize bars, which means they are are 1 1/8", not the smaller 7/8" diameter. Therefore some bikes will require a adapter and there are several available to select from.
Using the same manufacturing techniques and materials as ProTaper’s industry-changing 1⅛" motocross handlebar, the EVO Adventure is specifically designed to provide adventure/touring riders with the increased comfort and control they need. With over 8" of straight section in the control areas, mounting vital components is made easier than ever. With its premium 7000 series aluminum alloy construction and computer-profiled four millimeter-thick wall design, the EVO Adventure Handlebar is up to 25% lighter and 45% stronger than competing handlebars.
1⅛" tubing at the clamping area
Exclusive 4 mm-thick 7000 series aluminum alloy for superior tensile and yield strengths
Optimum balance between fatigue life, impact strength, and impact-absorbing flex
High-tech shot peened, stress-relieved, and anodized finish for unmatched durability
Independent lab tests show that the EVO Handlebar leads the market in fatigue life
Epoxy inner coating resists corrosion
Chemically applied cut lines and alignment grid are scratch- and peel-resistant
Plastic bar end plugs keep the elements out and provide a stronger base for grip ends
Weighs only 1.55-1.7 lbs. (720-780 grams), depending on bend
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!
The Complete Seats come assembled with an aftermarket pan and ready to ride.
The Commuter shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but is much more dished out towards the mid-point to distribute rider weight over a greater area. The passenger platform has been built up to help prevent the passenger from sliding into the rider.
The Commuter seat is the best choice for extended pavement riding and mellow offroad. The unique shape and added width will provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
The ProCycle seat was designed for both comfort and function. Our seat is built with an advanced Progressive Density Foam (Pd-F) for those long days in the saddle, and also giving you freedom to move while standing.
The wide and sturdy seat makes long rides more comfortable. The vinyl weave helps keep you cool by letting air flow between you and the seat. The front of the seat is narrower, giving you space for your knees when you're standing, while the sides have grip so you can hold on with your knees while riding.
We will build the seat for you in-house on a new seat pan so all you have to do is put it on and go ride. Choose the heated seat option and we will add a Seat Warmer during the build process.
Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 2 strong powdercoated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approx 13" long. Long enough to carry your Tire Iron Wrenches.
You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of the big Acerbis or Clarke tank? The 4.0 gallon tank from IMS might be just right. Includes cap, uses stock petcock.
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of a big tank? The 3.7 gallon tank from Clarke might be just right. It's almost 5 lbs lighter and holds close to 1/2 gallon more fuel than stock to increase your range by about 20 miles. Fits with your stock petcock, Pingel or Raptor petcock.
Universal fit. May require additional adjustment or modification.
These brake fluids are motorcycle approved DOT 4 brake fluid, and is specially formulated to exceed all DOT 3 & DOT 4 specifications. What this means to you is exceptional resistance to vapor lock and maintaining consistent lever feel during extreme brake use.
For use in all vehicles specifying DOT 3 or DOT 4 brake fluid
Durable and reliable stopping power
Anti-vapor lock formulation maintains responsive lever and pedal feel
Resists corrosion, oxidation and boil-off
Eliminated corrosion and lubricates fuel system components
Mixes with other DOT 3 and DOT 4 brake fluids
Exceeds US FMVSS 116 DOT 3 & DOT 4, SAE J1703, SAE J1704 and ISO 4925 (Classes 3 & 4)
License plate holder has been designed to replace the bulky standard assembly with a sturdy, neat unit. The Tail tidy accepts the standard Yamaha blinkers and is supplied with a LED number plate light.
3 piece CNC machined from high-quality alloy
Designed to bolt straight into position with no modification to the bike
It is a good practice to replace your sealing washer with every oil change. These 10 piece kits are made up of 5 Copper washers and 5 Aluminum washers. The manufacturer recently decided to make half of the kit Copper washers as that is the material of choice for many OEM manufactures. This gives you the opportunity to decide which you prefer, but either will work great at creating a leak-free seal between the case and the drain plug.
