Replace your handlebar mounted choke with this simple knob mounted directly on the carburetor.
Available in short or long reach.
Long reach is easier to use while wearing riding gloves.
Works for either the stock BST or Mikuni TM40.
Rebuild your crusty carburetor with parts from the same manufacturer the OEM companies use. Included in the kit are all necessary gaskets, O-rings, float valve and jets you need to rebuild your carburetor to like new condition.
Genuine Honda replacement air filter.
Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air- the number 1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow
The Mikuni TM42-6 HSR flows 17CFM more than the TM40-6 and incorporates many upgraded features such as a roller-bearing slide.
All this means going even faster has never been so easy, say goodbye to hard starting, hesitations and flat spots.
Quality air cutoff valve replacement kit contains parts necessary for a complete rebuild.
A brand new camshaft purpose built for the KLX140! The KLX140 is the ultimate trail bike. It just needs a little more power.
Note: The BBR KLX140 Performance Camshaft installs the same as the OEM camshaft (valve clearance IN: .002"-.003" / EX: .004"-.006"). We recommend you purchase an OEM Kawasaki KLX140 Service Manual to assist you when installing this camshaft.
As the leader in innovation, design and development of aftermarket high-performance camshafts, Hot Cams is certain to provide the added boost that enthusiasts are looking for.
Designed, dyno proven and made in the USA, Hot Cams performance camshafts are one of the most economical, reliable and easy to install ways to add a 5-10% power gain to your bike.
Stage 1: These cams provide better low RPM torque, pulling power, and throttle response.
Stage 2: These cams will provide improved full throttle torque and horsepower starting at 4000 RPM and up.
Tech Notes: This cam replaces the 2047-1IN. It has better low RPM torque, pulling power, and throttle response. For best results it should be used with the #2050-1E exhaust cam. Uses stock DRZ400 valve springs.
Stage 1. Excellent mid-range and top-end power increase. Uses stock valve springs and rockers
Fitment Specs: Exhaust Lift: 7.45; Exhaust Duration at 1.00mm: 265°; Intake Lift: 8.0; Intake Duration at 1.00mm: 238°
Includes three 9.48mm o.d. shims in each size from 1.20mm to 3.50mm in .05mm increments
The key to getting your built DRZ/KLX motor to make big power.
Put fresh O-rings on your KLR when you do your next oil change. Here you have new ones for the Oil Filler and the Oil Filter Housing Cover.
Complete set of engine gaskets with oil seals.
Choose standard bore top end, big bore top end or a complete gasket set for the standard bore motor. These are high-quality gasket sets from Athena.
The starter bushing in the DR650 leads a tough life. Exhaust heat and minimal lube from the factory take their toll. Warp 9 has a high quality solution - a billet starter cover with a sealed ball bearing.
Add a backup kick start system to your electric start DRZ400. Complete with everything you need to add the kick starter to your bike.
This kit will fit all DRZ400s but the manual decompression lever can only be installed on the 2006 to Current DRZ400 E models.
Barnett clutch springs are made from the finest materials available.
Heavy Duty Barnett clutch springs are pre-set, shot-peened, and heat treated for performance and durability.
ProCycle 440cc BIG BORE 89mm KIT 1 With Cam. Complete kit with 12.5:1 Wiseco piston (with rings, pin & clips), big bore cylinder sleeve, HotCams stage 3 camshaft and top end gasket set. You will have to have the larger sleeve installed in your cylinder.
ProCycle 425cc BIG BORE 88mm KIT With Cam Complete kit with 11:1 Wiseco piston (with rings, pin & clips), HotCams stage 1 performance camshaft and gaskets. No re-sleeving required. You will have to have your cylinder bored to fit the larger piston.
Includes all necessary o-rings and diaphragms
Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for the dunes or the race track! These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.
TechSpec’s Motorcycle Tank Grips were developed to improve body, bike control and increase riders comfort. Gripping your motorcycle between your knees or thighs improves overall control of your ride by better securing your body weight and seat position under the forces of braking, cornering and acceleration while also relieving pressure from your wrists, elbows, shoulders and lower back giving you increased control and a more comfortable, safer ride. Snake Skin is a thin, .125” medium durometer “rubber” material that offers a secure, comfortable grip, durable protection and a clean stock look.
This universal precut kit includes left and right tank grips. (8" X 3") Triangle
Seat Concepts seats are constructed using a foam material that is a higher quality than OEM seat foam. Their proprietary formula is a plush ride, while still offering the necessary amount of support. Their unique comfort and shape maintains a similar contour to stock seat at the front, so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!
The Complete Seats come assembled to a high quality with an aftermarket pan and is ready to ride.
"Will not fit standard L model"
| Width: | 10 3/4" (273mm) |
| Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Developed for Baja racing, their comfort model maintains a similar contour to stock at the front of the seat and tapers out towards the mid-point to distribute rider weight over a greater area. The Comfort seat is wider than stock, but not so wide that it would hinder movement in aggressive race situations.
The comfort model strikes the perfect balance between an aggressive race profile and a wider more comfortable seat.
| Width: | 7 5/8" (194mm) |
| Height: | Same as OEM |
For DL650 2012 - 2016. This new shape offers better comfort and support and also addresses the slope into the tank issue that the stock seat has. The passenger seating area is built up at the front to help the sliding effect into the main rider.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
Photo may not represent exact cover option.
| Width: | 14.5" (368mm) |
| Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
| Width: | 9.5" (241mm) |
| Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area. Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
The T700 Comfort Tall seat provides you with 1.25" of height compared to the OEM seat for increased reach to the ground.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
| Width: | 10.25" (260mm) |
| Height: | 1.25" (32mm) Taller than stock |
Available as a Foam & Cover Kit and an option for an OEM Rear Cover replacement cover to match the Kit.
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area. Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
The T700 comfort sport-touring seat provides you with an increased level of comfort and support to aid with those long days on the bike.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
| Width: | 13" (330mm) |
| Height: | Same as stock |
Available as a Foam & Cover Kit with rear cover only or rear foam & cover kit.
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
On this model, they built up the front of the seat, but dished out the rear slightly to level out the angle of the rider platform, and reduce the slope-into-tank feeling of the stock seat.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
| Width: | 12.5" (318mm) |
| Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
| Width: | 8" (widest point located in the rear seating area) |
| Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
Carbon Fiber Sides/ Gripper Top
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
| Width: | 10" (254mm) |
| Height: | Same as OEM |
This is a high-quality seat cover done by Moose for the TTR. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam. Strong marine-grade vinyl that's made to last. UV protected from sunlight for extended use and has double stitching for extra strength.
Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.
White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.
Dazzling bright Amber blinker functions.
Everything comes in a spring-loaded stock designed to keep it safe from those unexpected tip-overs, crashes, or encounters with brush and trees. They’re flexible enough to bend 360 degrees, yet tough, durable, and almost impossible to break!
If you have a single indicator light for the blinkers that is not built into the display and is not LED you will need the diode kit (AKA DR650) If it is built into the speedo display it should not require the diode kit.
Available in a generic kit with Bullet connectors supplied. Great for your DR or almost any other bike with a single post blinker setup. These will work well on bikes that use a flasher, but you might have to add the female side of the connectors that are included in the kit.
Not for Yamaha T7, see model specific listing
Taillight, brake light, & license plate holder (no plate light). Attaches to the underside of MX style rear fenders. Small and good looking!
The LITHIUM US is an advanced microprocessor-controlled charger specially designed to recharge and maintain the cells of Lithium-Iron (LiFePO4) batteries – maximizing their performance and lifespan. With up to 4.3A of charge current available the LITHIUM US is extremely flexible and will charge LiFePO4 batteries from 5Ah to 60Ah and maintain up to 120Ah.
The operation is simple and charging will commence upon connection. With no need to disconnect the battery from the vehicle, the LITHIUM US will automatically reset any low voltage protection electronics (Battery Management System) fitted. Charging can be restarted manually at any time using the ‘Reset’ button.
The CTEK LITHIUM US is a fully automatic ‘connect and forget’ charger with 8 charging steps including a testing sequence to show if the LiFePO4 battery can take and retain the charge, a unique maximization step to restore full capacity, and patented maintenance charging to ensure maximum performance even after months of inactivity. Splash-proof and dust-proof (IP65) the LITHIUM US is easy and safe to use, protects vehicle electronics, is spark-free, is reverse polarity protected and short circuit proof. The LITHIUM US features a 5-year warranty.
The CTEK Brand of chargers is recommended for all Antigravity RE-START (RS) Batteries (models with built-in jump-starting and full BMS protections)
Performance CDI for the Yamaha TTR125 increases the rev limit by 1,000 RPM over the stock rev limit. Easier starting, crisper throttle response.
This CDI box is a direct plug in replacement CDI. Simply locate and remove the stock CDI, and plug the new unit directly into the wiring harness, no modification needed. Suitable for stock and modified machines.
Designed to enhance overall performance when installing a high-flow jet kit. This CDI box enhancements include:
This unit may also be used to replace a defective CDI box on a stock machine. For 1990 - 2007 models only.
Heavy Duty replacement Voltage Regulator. More robust, but lower cost than the factory unit.
Operates turn signals, horn, headlight high/low/running/off, kill button. Blue LED high beam indicator. Includes wire pigtail with male & female 9-pin plug connectors. 1.75 inches wide. Wiring key included.
Complete high quality kit to replace the bearing and seals in the DRZ400 swingarm pivot.
Complete high quality kit to replace the bearing and seals in the DRZ400 shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Seal | 8 |
| Needle Bearing Shaft | 4 |
| Needle Bearing | 7 |
Complete kit to replace the bearings and seals in the KLR650 swingarm pivot.
| Kit Contents: | |
|---|---|
| Seal | 4 |
| Needle Bearing Shaft | 2 |
| Needle Bearing | 2 |
Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.
Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward.
Simple to install and completely tunable for all conditions and rider preferences.
These Cogent Dynamic Drop-in Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.
The complete fork upgrade kit - Straight rate springs and Race Tech Gold Valves. Also includes a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
Progressive springs offer a soft initial spring rate for a plush ride. Progressively wound design provides increased resistance to bottoming as spring compresses. These springs are significantly stiffer than the wimpy stock springs.
They will make a big improvement in front fork action while still delivering a smooth ride. Sold in pairs.
High quality replacement seals for your TW200 forks. Includes both oil seals and dust seals.
The Magura Hymec Hydraulic Clutch system. Simply remove the stock perch, lever and cable and bolt this in its place. This system replaces the stock cable with a small lightweight hydraulic system for improved clutch control, easier operating pressure, a constant pressure point and smoother actuation. Developed over many years and tested under the toughest conditions possible in the off-road motorcycle world.
You will have to bypass your clutch safety switch to use this unit.
Never hurts to have a bit of the Margura specific Blood Red hydraulic fluid as well.
Warp 9 Flex 3-Finger Levers are machined Billet, anodized and hinged levers with CNC machined master cylinder interfaces.
Adjustable reach allows customization to the rider's hand size.
Double hinge design allows lever to flex out of the way in most impact situations.
Pushrod or Bearing contact styles for smooth modulation.
The Warp 9 shift lever is 7075T6 CNC arm, the Warp 9 logo is laser etched into the finish.
Includes a black folding aluminum tip and stainless spring and pivot pin for years of rust free use.
1" longer than stock
Folding tip, forged aluminum shift lever from BBR Motorsports. Stronger and lighter than the stock shift lever, with a beautiful anodized (titanium color) finish.
Warp 9 Flex Brake Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces.
Adjustable reach allows customization to the rider’s hand size.
Double hinge design allows lever to flex out of the way in most impact situations.
Pushrod or Bearing contact styles for smooth brake modulation.
Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal.
A quality set of replacement throttle cables from Motion Pro
A quality replacement speedometer cable
These heated grips from Koso have been tested by us and we can say they will keep your hands warm and give you the grip you need in off road conditions, thanks to the full diamond grip design.
This retainer is has a no hassle installation for quick change sprocket swaps with simple readily available tools (pliers and screw driver).
This spring clip retainer takes the place of the OEM two bolt retainer and fasteners when a FRITZCO sprocket is used.
Designed for OFF ROAD USE with the thought in mind that you can ride to your favorite off road spot using a 15 or 16 tooth sprocket and larger than stock rear sprocket. Then quickly change to the 13 tooth and enjoy the ripping torque provided by the huge amount of reduction the 13 tooth offers. Making the XRL much better in the technical stuff. You will really be surprised how much better a big bike like an XRL handles off road with low gearing.
This retainer can only be used with FRITZCO sprockets and can not be used with thin OEM type sprockets.
These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
The DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 84db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.
No repacking required! The Leo Vince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed a 84dB sound level using the USFS J1287 testing procedure. 84dB is louder than stock but significantly quieter than any other aftermarket muffler. It includes a certified Spark-Arrestor.
This muffler works on OEM header only!
Replacement Exhaust Pipe Retention Spring
These flat tie down 'stretch' straps are designed specifically for motorcycles, ATVs and snowmobiles. Carry anything on your motorcycle securely and without scratches with these flat - no hook - tie down straps.
ROK Straps are a two-piece strap with a quick-release buckle in the middle and loops on each end. One end of the strap is a heavy duty nylon, the other has a strong stretchable section. Instead of hooks that can slip or come undone, ROK Straps have a loop sewn in each end. you pass the buckle around your frame, rack or other secure point and then back through the loop in the end making for a very secure mount. With each end secured, connect the buckle in the middle and simply tug the slack end of the strap until your load is firmly held in place.
The Motorcycle Adjustable Strap is 1 inch wide and adjusts in length from 18 to 60 inches.
Rated to carry 100 lb (200 lb burst strength)
Designed specifically for motorcycle and ATV use.
You can add the double D ring loop to any 1" flat webbing system. This simple piece adds a lot of flexibility to any luggage system you are using. Instantly and easily create a mount point or adjustment point on almost anything. Double D Rings can be used as a secondary buckle and works the same way as a helmet strap. However, the double D rings should NOT be used as a primary means of securing luggage.
Available in 6 colors.
CONSTRUCTION FEATURES
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series KLX300 rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready!
This is the ENDURO Series TW200 rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series CRF300L rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series CRF250L rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
This Trekker Top Case is manufactured from glass fiber reinforce polymers ensures high structural rigidity. An anodized aluminum cover is then placed over that to resist weathering. 52 liters in size, there is enough room for 2 helmets. Attaches to your favorite rack with a Monokey fixing system. Available in Aluminum or Matte Black.
Fly Racing small tank bag has a 7.5 liter capacity, with touch screen compatible top map/device pocket that holds most GPS and cell phones.
Combined strap and magnet mounting system, reflective piping and logos, and convenient carry handle.
Micro fleece lined exterior pocket, and includes rain cover. Measures: 13"L x 10"W x 5"H
Rotors are laser-cut from high-carbon content 410 stainless steel then lap cross hatch ground and heat-treated. The finished rotors are mounted on a floating black steel carrier for durability and strength.
The oversize floating pins are CNC machined stainless steel rivets with stainless wave washers to ensure they will not crush as more traditional steel pressed rivets can. Finally, high-temp paint is applied to surfaces like cooling holes and edges to provide a clean, finished look.
Includes a fresh set of brake rotor bolts.
These DP Standard brake pads are our OEM replacement sintered metal compound. Ideal for everyday use, both on and off-road. They provide excellent all-round braking hot or cold, wet or dry. Where applicable a high-tech ceramic heat shield is applied to the rear of each backplate to reduce the heat transfer into the fluid and prevent brake fade. They have one of the lowest wear rates on the market, very low levels of brake dust and no noise and no thermal cycle bedding-in required are also benefits of the DP Standard brake pads.
This is the ultimate in radiator guards! It will protect your fragile radiator from nasty front & side impacts.
This ultra tough guard is constructed from 3/16" aluminum and is easy to install.
This radiator guards uses brace rods for that extra support! All Mounting hardware is included.
The TKC80 has a self-cleaning tread pattern along with high levels of side stability on soft surfaces with very good road handling manners. It is also original equipment on the BMW 1200 GS Adventure and KTM 690 Enduro R. Some of the tires are designated as tubeless type. Please note that Tubes can be run in Tubeless tires, but a Tube Type Tire cannot be run Tubeless.
Limited Sizes Available
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever!
Pivot Pegz have set a new standard in foot peg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best foot pegs in the world and they really do perform as good as they look. There's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
If you are replacing your side stand you will want to check the hardware. Over the years they can take a beating and the springs become lost or broken.
This is the full kit that includes #4, #5, #2, and #3 in the diagram.
Slack control has never been more convenient.
Simply slip the webbing through the slots and use the shock cord to secure the slack.
You can roll the webbing around the Web Dominator or you can bundle the webbing and secure it by snapping the shock cord around the built in anchor.
Sold in a package of 4.
No Toil rim grease is a high viscosity, non petroleum based compound specially engineered to provide the ultimate filter rim to air box seal.
Designed to withstand temperatures up to 300° F, it remains waterproof and dust-proof, keeping damaging dust and water from being drawn past your filter
License plate bolt with bright white LED light. The simple way to light up your plate.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 2 |
The current ProCycle logo on front, with the design on the back showing our favorite 'Pavement Ends' sign with the DR rider continuing up the road on the pegs, ready for an adventure!
High quality soft blend t-shirt perfect for everyday wear (90/10 Airlume combed and ring spun cotton/poly).
Only available in size Large.
Mapping America's Back Roads
Amazingly detailed, large-format topographic & street map atlases of all 50 U.S. states. Unbeatable recreational information & detail.
Map detail includes:
Limited to stock on hand
From Warp 9, top of the line Adventure Pegs. a full 5" long and 2.5" wide will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a single track trail.
NOTE: These pegs DO NOT fit the '18 model!
Set includes:
This tool helps ease the pain of accessing the neutral safety switch. This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub.
Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut a breeze, and minimizes the likelihood of damaging the clutch hub.
Small scuffs on the inside of the bash plate as shown in image, does not affect performance or fitment. Polished finish only, sold as is, all hardware included. Does not qualify for free shipping.
The Honda CRF1100 DCT Bash plate is a full coverage Rally style protection for frame rails & lower to mid engine cases. Constructed for more serious off road use in mind, it features multiple additional mount points, paired with a semi double skin 4mm 5083 aluminum Bash plate. All CNC machined and fully tig welded, the side wings are partial double walled for extra stiffness. It also features the addition of a HDPE end plate for the clutch case mated to a rubber puck insert on the plate for additional protection.
Finish Options
Whats Included-
Additional Info-
Replacement OEM swingarm pivot covers. Keep mud and dirt away from the swingarm bolt. Sold as a set of one left side and one right side cover.
Permatex Gasket Remover will help you remove that stubborn gasket without having to scrape so much, possibly damaging surfaces. Prepares surfaces for new gaskets. Give it plenty of time to soak in.
Windscreen attaches to your bike's handlebars. Fully adjustable mounting brackets. Includes 7/8' handlebar clamps. 14" tall & 10" wide.
Will not fit 1 1/8" oversize handlebars.
