Search Products

These masterlinks fit the original OEM Suzuki chain. The original chain is marked DID 525 V8. Choose from Clip Type or Rivet Type.
 

Quality steel sprockets and 525 O-Ring chain. 525 chains come in 120 link length and will have to be cut down to fit. They also come with rivet type master links. Clip type master links are available below. Single sprockets and chains are also available below.

Choose either a 14, 15, 16 or 17 tooth JT countershaft sprockets.

Go down in tooth count for faster acceleration.

Go up for lower RPMs at cruising speeds.

Quality steel front sprockets. Choose 525 or 520. Also available 'Wide Boss' JTF438 520 sprockets.

  All 520 sprockets require a new retainer plate, please add on if purchasing this size.

We have 44, 45, 46 and 47 tooth rear sprockets available for the SV. Select the sprocket size from the dropdown.

Quality steel rear sprockets. Choose 525 or 520. 41T to 50T

48 and 50 sprockets require removal or modification of your lower chain guide.

Chain Size Recommendations:

• 110 link chain for a 42 tooth rear sprocket
• 112 link chain for a 46 tooth sprocket
• 120 link for the 48 and above sprockets.
• 120 link chain will have to be cut to the proper size for the 48 and 50.

*Actual sprocket color may differ from image shown.

Quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

Many riders choose to convert over from the stock 525 to a 520 chain. Besides being lighter and less expensive, a 520 chain is more readily available as well as having more sprocket size options.

• Steel Sprockets
• EK SRO6 O-Ring Chain (clip type master link)
• Smaller 3 hole retainer

Aircraft aluminum withstands hard hits from logs and rocks. All mounting hardware and wear blocks included.

Here is a complete kit to install oversized tapered 1-1/8" handlebars on your DR650. Warp9 handlebar clamps bolt to your stock triple clamp adding an additional 1" to the height.

Alloy oversize bars offer more durability and eliminate the crossbar which opens up your dash area for more goodies. Black in color.

A quality set of replacement throttle cables from Motion Pro

Genuine OEM replacement choke cable.

A quality replacement speedometer cable from Motion Pro.

• Black vinyl coil-wound housing
• Meets or exceeds OEM quality
• Inner nylon sleeve for longer life and smooth operation

Spare replacement throttle cables for your TM40 carburetor conversion. Fits the stock throttle housing.

These are premium low-friction cables. 

A quality set of replacement throttle cables.

A quality OEM replacement clutch cable.

A set of polished aluminum replacement brake and clutch levers.

• High-quality direct replacement for OE (stock) lever
• Integrates perfectly with stock components
• Manufactured to OEM tolerances

Replacement shift lever from IMS with folding tip.

Original Suzuki factory replacement levers for your DRZ400S/SM/E

The new Fastway Evolution AIR footpegs are now the ultimate pegs in the Universe.

Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way. Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.

You can also order serrated or spiked cleats separately. See images.

These AIR pegs are offered in several colors, but some colors may require extra time, call for availability.

Finally, the ultimate Adventure peg, from the folks at Fastway - Pro Moto Billet. This peg is big enough to stand on all day with no fatigue, it measures 2.25" front to back and is 4.75" wide.

In addition to the big size, you can also adjust the camber with their patented FKMS Kamber bolt. ´Tilt´ your pegs to increase comfort, or to give better squeeze on your bike. You can further customize them with 3 styles of patented adjustable threaded cleats. Take your traction from comfortable to gnarly. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long. You can also order serrated (F5 - bottom left image) or spiked (F6 - bottom right image) cleats separately.

These Adventure pegs are offered in several colors, but some colors may require extra time, call for availability.

Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.

Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.

• Mega wide 60mm platform
• Widest and lightest pivoting pegs on the market
• Open design = less mud packing
• Unique multi-directional grip pattern
• Outstanding build quality
• Race proven design and durability

Not your average rubber insert! These rubber covers go over the top of your MK3 or MK4 Pivot Pegz so that the aggressive teeth are only exposed when you need them in muddy conditions.

• Unique, innovative design
• Wide flat platform
• Openings allow mud/dirt to pass through
• Easy and quick to get on/off
• Good grip
• Reduced vibration
• Extra comfort

Important to verify which style Pivot Pegz you have before ordering.

Light weight and strong. These DRC foot pegs have a wider platform for increased comfort and control. Cast from Chromoly steel for unbeatable strength and durability.

Made from 1/8" thick stainless steel with dual folded edges for additional strength, these brackets will relocate your passenger pegs down 4" and move them back 1.5". This will give your passenger additional legroom making two-up riding much more comfortable.

All hardware is included for a quick and easy installation.

Low peg mounts from JNS Engineering. Your choice of a straight 1.5" drop or get that drop and a 1" rearward offset. You can use your stock pegs or click on one of the optional pegs that are made to fit the stock DR650 mounts.

These heavy duty steel mounts are pressed, welded and then powdercoated black for protection. Includes mounting bolts.

Note: These mounts are compatible with the SW Motech Center Stand by adding a 1/8" spacer behind the mounts.

Our complete foot peg assemblies. 1-3/4" lower than stock. No extra brackets that hang down below the frame. Easier on the knees. Wider platform Yamaha YZ style footpegs are stronger and give you firmer footing. Mount solid to the frame. No more 'droopy' feeling when standing on the stock pegs. Lowering your footpegs makes it easier to stand and less of a reach down to the bars when standing.

Now you can get our Low Pegs with MK4 Pivot Pegz or black Fastway ADV pegs (both Yamaha YZ pegs) installed!

Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way. Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.

You can also order serrated or spiked cleats separately.

These AIR pegs are offered in several colors, but some colors may require extra time, call for availability.

Fastway offers a large ADV peg that is 4.75" long and 2.25" wide. With these pegs you can adjust the camber with their patented FKMS Kamber bolt. ´Tilt´ your pegs to increase comfort, or to give better squeeze on your bike. These pegs come with two sets of F3 cleats (one standard, one long). You can order serrated or spiked cleats separately.

These Adventure pegs are offered in several colors, but some colors may require extra time, call for availability.

Pivot Pegz have set a new standard in foot peg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.

Pivot Pegz aim is to build the best foot pegs in the world and they really do perform as good as they look. There's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.

• Mega wide 60mm platform
• Widest and lightest pivoting pegs on the market
• Open design = less mud packing
• Unique multi-directional grip pattern
• Outstanding build quality
• Race proven design and durability

This will give you a complete SET (Front and Rear) of brake pads.

• Sintered Pads are best for regular riding -long life, and good performance in all conditions.
• Sport Carbon pads are made for fast riding in dry conditions - not recommended for mud, water, or sand.
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand

Kit includes front and rear brake pads.

Built with the latest in Lithium Ion Polymer Technology. All components are designed, manufactured, assembled and packed in one location assuring high quality and consistency. Besides extreme lightweight (50% to 70% lighter than standard lead-acid batteries) it also features a built-in LED test gauge and the ability to mount it in any position. There is no hazardous acid or heavy metals, it is non-explosive and non-combustible.

The Firepower features Increased cranking amps over lead acid batteries and has a very fast recharge cycle and can be brought up to a 90% charge within 6 minutes and also has 6 to 12 times more cycle life when compared to lead acid batteries. A 2-year warranty insures that your investment is protected.

165 CCA 12V/36WH
Package Dimensions: 6.20 x 2.80 x 4.30

Heavy duty replacement voltage regulator. More robust but lower cost than the factory unit.

This high output stator will allow you to run brighter lights, heated gear, heated grips, etc. From ElectroSport

Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.

Iridium spark plugs are made with premium quality materials.

Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.

• The ultimate in the evolution of spark plug technology and performance from an industry leader
• The iridium electrode is 25% smaller than a platinum electrode, and it's just 1/4 the size of a conventional nickel electrode
• Ultra-small diameter center electrode reduces voltage requirement and extends ignition system life
• Metal shell plating has enhanced anti corrosion qualities

Sold individually, unless otherwise stated.

ProCycle 425cc BIG BORE 88mm KIT With Cam Complete kit with 11:1 Wiseco piston (with rings, pin & clips), HotCams stage 1 performance camshaft and gaskets. No re-sleeving required. You will have to have your cylinder bored to fit the larger piston.

ProCycle 440cc BIG BORE 89mm KIT 1 With Cam. Complete kit with 12.5:1 Wiseco piston (with rings, pin & clips), big bore cylinder sleeve, HotCams stage 3 camshaft and top end gasket set. You will have to have the larger sleeve installed in your cylinder.

ProCycle 440cc BIG BORE 89mm KIT 2 With Cam Complete kit with 11:1 Wiseco piston (with rings, pin & clips), big bore cylinder sleeve, HotCams stage 3 camshaft and top end gasket set. You will have to have the larger sleeve installed in your cylinder.

All in one package.

• Hot Rods complete +4mm stroker crank assembly
• 94mm big bore cylinder and piston kit
• Complete gasket set with seals
• Includes new crank bearings

We suggest adding a set of HotCams camshafts and a new clutch kit for the best results.

• Direct bolt-on, ready-to-install cylinder; requires no replating and looks virtually identical to the OEM
• Nickel Silicon Carbide plated for long life
• Honed to exact size for easy piston installation
• Big bore cylinders do not require any machine work
• Come complete with gaskets, cylinder, 94mm piston, rings, pin and clips

• Constructed using the best materials available
• TUV approved and production monitored to ensure OEM or better quality
• Sold as a package of 5 oil filters

Made from laser-cut, medical-grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area over many paper filters, catching debris down to 35 microns. The FLO filter pleat seam is welded and able to withstand up to 600 deg. F. Filter maintains consistent flow under all conditions including extreme heat, the presence of water and cold start-ups where paper filters can flow so poorly that they often cause the bypass valve to open and allow unfiltered oil to enter your engine.

This cleanable oil filter should be the last one you ever purchase.

Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

Grab our 5-pack and save both time and money!

• High-temperature silicone guaranteed to 356° F
• Smooth flow and improved insulation promotes radiator efficiency and improves engine cooling
• Single molded, Y-piece hoses eliminate the need to reuse OEM 3-way fitting which reduces weight and eliminates leak points
• Three layers of reinforcement fabric offer high burst pressures and provided better debris/crash resistance
• UV stable colors don't fade with heat or sun and are color matched to OEM brands

Add a backup kick start system to your electric start DRZ400. Complete with everything you need to add the kick starter to your bike.

This kit will fit all DRZ400s but the manual decompression lever can only be installed on the 2006 to Current DRZ400 E models.

Always a good idea to put in a new set of Oil Change O-Rings at the first sign of any leakage. This package gives you the three most important: oil filter cap and the one behind the filter as well as the one on the filler cap. All are new OEM Suzuki O-Rings.

A complete set of gaskets, o-rings and oil seals. Everything you will need when doing a complete engine re-assembly.

New Bearings for your DRZ400.

If you are in the lower end doing work, new bearings are cheap insurance for all that hard work.

• Hot Rods complete stroker crank assembly includes +4mm stroke for maximum power and performance output.
• Hot Rods constructs their complete stroker crank assembly to meet or exceed OEM specifications for maximum durability.
• Hot Rods stroker cranks are completely rebuildable and have been trued to within 0.001" from the factory.
• The Hot Rods stroker crank increases the stock displacement to 424cc when used with the stock bore piston or 462cc when used with a 94mm big bore kit.
• Main bearings sold separately.

This will not fit the DRZ400 kick start models. Nothing is available for the kick start models.

Replace your worn clutch plates and springs to reduce fade and slip.

• Complete set of friction plates, steel plates, and springs
• Heavy-duty springs help prevent clutch slip
• Restores proper stack height, fixes clutch slip caused by wear and tear

A high quality cam chain from the folks at Wiseco. New cams, big bore kit, high-mileage motor, you might want to think about a new cam chain. Direct replacement for stock unit.

The GPR v5 is the fifth generation steering damper designed for dirt bikes, adventure bikes but is also used on several of hybrid applications. Its compact and slim design allows for the damper to be mounted below the handlebars, out of harm's way, without raising the bars more than an inch. Frame mounts are machined steel or Cryogenic treated billet aluminum with stainless steel pin, and billet aluminum machined bar-mounts.

• Kit includes damper, bolt on post mount, below the bar mounting system, and complete instructions.
• Bolts onto the OEM triple clamp replacing the stock handlebar mount. Will raise the Bar height about 7/8th". Fixed position.

• Will only work with Fat Bar style (1 1/8" clamp area) handlebars and stock triple clamp.

The ProCycle rack system is designed and manufactured by dual sport riders that know what it takes to create a durable and versatile luggage rack.

Our racks allow for easy installation of both soft and hard luggage.

See the linked instructions for how-to videos.

CNC machined from 5mm aluminum 5083 plate with lots of slots to attach your Rok Straps (or other straps). This gives a considerably wider deck than the standard B&B Rack. Attaches directly to the B&B rack with four screws that are included. Available in either polished aluminum or a black polymer coating.

These plates are pre-drilled and countersunk from the bottom making installation of a RotoPax mount quick and easy.

Some older carry racks will not have predrilled holes in them to mount luggage plate in which it will require you to drill yourself (select pre2018 version)

  This is for the add -on Top Plate only.

Hand built aluminum luggage rack from the B&B Off Road Engineering folks down under. This unit really is a beauty to look at and extremely rugged, made from 4mm 5083 aluminum plate! Tie down whatever you need with confidence. Whether it's your books to get to school or a bag to get across the country, no worries mate. Available in either bare polished aluminum or with a black polymer coating.

While plenty rugged to use as grab handles, you can keep your stock handles if you so desire. All necessary stainless clamps and bolts are provided.

If you want a wider platform for support, consider adding the luggage plate to this rack.

  Bike must have the DR250 Taillight installed to work with this rack.It will not work with the stock USA taillight.

DRZ400 rack is available in both a Utility and Sport version. The Sport version is 9" x 9" and the Utility is a full 2" longer for added storage space. Both of the S/SM racks have tabs so you can bolt the stock tool bag on.

Please select the rack for your specific model as the differences are significant

• Fully welded construction from 16 gauge mild steel
• Powder-coated black textured finish
• Rigid 4 point mounting system (except off-road model rack)
• Hardware and detailed instructions included

Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists and then anodized black.

The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary hardware is included.

Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets.

This DRZ400 rear rack, hand-built by B&B Engineering in Australia is made from 4mm aluminium 5083 plate tig welded to the support tubing circumventing the plate. This material was chosen because of its extreme suitability for welding as well as abrasion and impact resistance, and all of this keeping in mind the full weight of the bike and rider. Once complete they are given a polished finish or coated with a super-durable black polymer. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible.

These racks are smooth and sturdy enough to use as a grab handle.

Check out the bolt-on Luggage Plate for the B&B Rack for those times you need to carry a larger load!

Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 3 strong powder coated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approximately 13" long.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

Does not fit if your bike is equipped with the new emissions system. The charcoal canister prevents the tool tube from being mounted properly.

The DR650 is rather hard on the cush drive rubbers. Replace these any time you feel excessive play in the sprocket carrier hub. Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier. Sold as a set of 6 rubber dampers.

Make the installation as easy as possible with this Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight Circuit Board Upgrade making the connection simple. Stock plug will go right into this unit and off you go. You will need a crimp tool or set of needle nose pliers to crimp connectors on.

Make the Edge-2 Circuit Board installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. You will need a crimp tool or set of needle nose pliers to crimp connectors on.

Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.

Also works with Edge-2 Circuit Board Upgrade.

The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail/stop light function. 3 white LED's are used for license plate illumination.

Included is a set of turn signal brackets that bolt to the mount, but these are designed for a smaller LED type signal with a mounting stud of just 8mm. If you think this might be a problem, look at the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!

NOTE: LED's must be installed on a 12 V DC system!

Seat Concepts seats are constructed using a foam material that is higher quality than OEM seat foam. Their proprietary formula is plush, while still offering the necessary amount of support. 

Their unique comfort and shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.  

These great features combine to offer you a custom seat feel, and provide greater enjoyment and increased range for long commutes, or Dual-Sport rides!

The Complete Seats come assembled with an high quality aftermarket pan and are ready to ride.

State-of-the-art replacement seats, Sargent seats are built on a percision-molded lightweight Polytec seat pan. Sargent's proprietary seat foam (Super Cell Atomic Foam) is their own unique blend of resilience, firmness, and vibration-absorption qualities, making it well suited for long distance comfort and support. Sargent seats are covered in a marine-grade, UV-stablized mildew resistant CarbonFX vinyl. These seats will fit bikes with the stock, IMS, or any other aftermarket fuel tank.

Moose Racing Adventure seat provides improved comfort for your riding adventures, or just commuting around. You choose between the stock seat height, or a low seat height (about 1 inch lower). The durable micro-fiber suede top cover enhances rider comfort and increases stability. Side gripper panels ensure secure seating during aggressive maneuvers. The cover is constructed from smooth marine-grade vinyl and features an embossed Moose Racing logo. It includes a strap kit that enables secure attachment of cargo to the pillion section of the seat.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam. On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as similar to stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.

This is a high-quality seat cover done by Moose for the DRZ400. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam. Heavy-duty marine grade vinyl with UV protection for long life. Double stitched for durability too!

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

The EJK evolved out of the need to address the ever-increasing complexity of factory fuel injection. For the newcomer to the market or professionals wanting an easier method for tuning fuel injection, the EJK is a customizable solution for the rider that wants to take control of their tuning needs.

This unit is a piggy-back EFI controller because it does not replace the stock ECU, but rather monitors the signals to the injectors and makes fuel adjustments based on the mode settings. The GEN 3 has a push button interface allowing access up to 6 different modes to allow for quick fine tuning by the end user without needing a computer.

Key Features:

• No computer or dyno needed!
• Plug and play, simple to install, base settings preset
• Unique load based technology
• Full range tunability available
• Does NOT interfere with stock ECU operation
• Simple push button adjustment interface
• Water-resistant 
• 2-Year warranty
• Compact size - 2.2" H x 3.4" W x 0.5" D

For mildly tuned machines using the stock airbox, with stock or K&N filter. May also be used with a good aftermarket exhaust system

• Provides a simple and affordable solution to carburetor tuning problems.
• Allows you to tune your bike for increased power and smoothness while retaining fuel economy.
• Includes a guide booklet on how to install and use your jet kit to it's full potential.
• For a top quality installation we recommend adding an extended fuel screw and a set of replacement carb screws.

Dynojet Jet Kits increase power and smoothness throughout the entire rev range, while maintaining optimum fuel economy. Each Dynojet Jet Kit includes comprehensive instructions which show step-by-step installation and testing procedures to ensure a perfect setup every time.

• Stage 1: stock engine/filters, stock/modified pipes; about a 5% power increase
• Increases power and drivability
• Fully adjustable

This kit is for the 36mm Mikuni CV carburetor and includes 2 Needles that have been developed by JD Jetting and manufactured for them to their exacting specifications. These two needles allow a wide range of tuning possibilities and provide correct fuel delivery at any throttle position.

4 allen type screws for the top of the carburetor are also enclosed should you strip out the stock screws during your tuning process. Complete instructions with photos, jetting suggestions for different set-ups and situations, 5 Main Jets, a Pilot Jet and a drill bit complete the package.

• Increased air flow over the stock air filter.
• Designed to increase horsepower and throttle response.
• Easily fits inside the factory air box.
• Larger surface area over foam filters which offers longer service intervals in dusty conditions.
• Four layers of premium cotton gauze provides outstanding filtration.
• Washable & re-usable, never wears out.
• One filter will last the lifetime of your bike.

Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.

The air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air-the #1 filter system proven on motocross tracks around the world.

Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow.

From Warp 9, top of the line Adventure Pegs. a full 5" long and 2.5" wide will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a single track trail.

• Ceracote coated Chromoly steel pivot for the ultimate in strength
• Replaceable 7075 T6 Aluminum Platform
• Permanent Stainless Teeth provide the ultimate in non-slip traction
• Built-in bottle opener in the bottom!

  NOTE: These pegs DO NOT fit the '18 model!

Special tool to remove the flywheel from the end of the crankshaft.

Shield your bike’s vital drivetrain components with B&B Off Road’s heavy-duty front sprocket case saver. This premium guard, CNC-machined from high-strength 6mm aluminum plate, offers unparalleled protection against rocks, impacts, and other off-road hazards.

Uncompromising Strength, Precision Fit:
Engineered for maximum durability, this case saver boasts a 6mm main body crafted from 5083 structural aluminum – a material renowned for its resilience. Complementing this robust core is a 4mm thick front sprocket cover, ensuring comprehensive protection for your drivetrain.

Designed for Flawless Performance:
CNC machining guarantees a precise fit for both Suzuki DRZ400 (2000+) and Kawasaki KLX400 (2000+) models. This ensures seamless integration with your bike, eliminating concerns about interference or compatibility issues.

Peace of Mind on Every Ride:
Whether you’re navigating technical single tracks or powering through dusty plains, this case saver offers the confidence to push your limits. By safeguarding your front sprocket and surrounding components, it minimizes the risk of costly repairs and keeps you on the trail.

• Made from 5083 structural aluminum for durability
• 6mm thick main case saver body
• 4mm thick front sprocket cover
• All components CNC machined for a precision fit
• Fits 14 and 15 tooth sprocket

Need to remove your clutch assembly? This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub. Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut easy. All of that and no worries about doing any damage to your expensive clutch hub.

One of the most advanced radiator protection systems available for the DRZ400. These guards feature maximum side and front impact protection by using a combination of CNC machined 6000 series aluminum and 5000 series alloy plate to create a complete system to protect your radiators from virtually every direction. Roost and debris protection is exceptional thanks to the angle fin design that leaves minimal exposure to the radiator core and veins.

Even with all of this protection, cooling airflow is still at its maximum with a front louvered panel built with fins designed to mimic the airflow characteristics of the OEM plastic fins. This panel can be removed easily facilitating cleaning of the radiator.

Three-piece modular construction eliminates the design limitations of one-piece designs. Integrated modular construction- Three piece modular construction allows for greater design flexibility eliminating the compromises inherent with one piece designs. Easy fitment no mods required- Radiator guards can be fitted in approx ½ hour using basic tools. Sold in pairs, but repair parts are available individually.

Can be fitted with 17L safari tank & Acerbis tank 

Will not fit the "S" & "SM" model if thermo fan is fitted

Clutch and Ignition covers made by B&B Eng. Formed from 2mm thick 5052 aluminum plate, selected because of its strength, corrosion resistance, excellent abrasion and impact protection. These will help protect your cases in the event of a bad fall.

These covers are attached to the engine cases with high quality heat resistance silicone adhesive

These covers will NOT fit early kick start only models that did not come standard with electric start. If you have added a kick starter to your bike that came with an electric start, covers will fit with no problem.

The B & B Eng. DRZ400 Bash Plate is made from 4mm thick 5083 aluminium plate. Strong and great looking, this is the top of the line protection plate for the DRZ. Supplied with all the necessary stainless steel clamps and bolts required. Available in polished or with the heavy-duty black polymer coating. Like all he other B&B Bash Plates, these plates have foam or rubber where required to keep things a bit more quiet. This plate fits the E, S, SM & kick start models.

Replace the wimpy stock DRZ400 Skid Plate made from 4mm thick 5083 aluminium plate. Strong and great looking. Leave the stock wings in place and give yourself something that will really stop any damage between the frame rails. Supplied with all the necessary stainless steel clamps and bolts required. Available in polished or with the heavy-duty black polymer coating. Like all he other B&B Bash Plates, these plates have foam or rubber where required to keep things a bit more quiet. This plate fits the E, S, SM & kick start models.

Thick carbon fiber plate with many advantages over aluminum.

The use of anti-ballistic composite material provides a longer fatigue life and greater tensile strength than aluminum.

Composite plates are molded to the exact shape desired, making for a closer fit and a more protective plate.

Composite plates absorb vibration and do not amplify sounds like aluminum plates do.

When hit hard, aluminum permanently deforms, bending frame tubes and slicing into water pumps.

Composite plates will bounce back from hard hits and look great long after aluminum plates give up.

Skid plates protect the side engine cases and the water pump in addition to the frame and the center case.

Designed with a high front to keep mud from building up on the engine.

Mounting hardware included.

• Made from strong and lightweight aircraft aluminum
• Protects vital engine parts from rocks and debris
• Custom fit to your specific bike model
• Oil drain hole for easy access
• All mounting hardware included

Protect your frame/paint from scuffs and scratches with frame guards. The DRZ 400 frame guards are made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.

This is without doubt the fastest, most effective, most meticulous, precise and systematic method for giving your chain a thorough cleaning. It forces its bristles between the plates where dried and hardened chain lube, road sand, glass, tar and other materials gather to form a hard shield of abrasive dirt where the O-ring meets the chain plates. 

• Chemical resistant nylon brush
• Flexible and adjustable
• 360 degrees of cleaning
• Compact size for easy storing

Note: Designed to be used with the engine off

Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.

• Will not harm O-ring chains
• Easily adjustable for all chain sizes

Contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

Complete set of 'Adventure' wheels. These are the same rim sizes as used by the BMW GS and other big adventure bikes. The 19" front and wide 17" rear will give you great twisty road handling on the pavement while still being dual-sport friendly.

We start with silver Excel or Sun rims, OEM hubs and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.

Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.

• New OEM hubs with bearings and seals installed
• Excel 2.5" or Sun 2.75" x 19" front rim
• Excel or Sun 4.25" x 17" rear rim
• Buchanan's stainless steel heavy gauge spokes and zinc-plated nipples

Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.

The stock tail light, blinker and license plate bracket is rather large and cumbersome, to put it politely. The B&B Off Road Engineering unit is simple and tidy and gives you a LED tail and brake light unit, a LED license plate light and turn signal mounts as well.

Installation is easy - remove the stock unit and bolt the new unit in the same location. Off with the old and on with the new in minutes. All necessary hardware included.

B&B fired up the CNC equipment for another beauty, a Front Sprocket Case Saver. A great investment the 6mm aluminum base will protect your engine cases should your chain ever break or derail. On top of that is a 4mm piece to keep your pants and other things out of the chain as well. This replaces the stock cover over the countershaft sprocket.

If you have a 16t front sprocket, mounting modification may be needed to fit.

This nice piece replaces your plastic sprocket cover and protects your engine case from a chain derailment or failure. The 3/16" (5mm) thick steel plate is adjustable to accommodate 14, 15 and 16 tooth sprockets. Includes mounting hardware.

B&B Off Road Engineering Fender Brace is made to help support your front fender/guard. Also helps support and reduce fatigue from constant vibration.

Made from 4mm 5083 structural aluminum plate. If you wanted to carry a small tool bag this would be a perfect product to support the weight and strap the bag to.

Fits on top of the fender and bolts between the fender and bottom triple clamp. Requires you to drill one hole in the fender for mounting.

A highly refined blend of aluminum, copper and graphite lubricants. Use during assembly to prevent galling, corrosion and seizing due to weathering or chemicals. Anti-Seize assures easier disassembly. Temperature range: -60°F to 1600°F (-50°C to 870°C). Salt, corrosion and moisture resistant – ideal for marine use. Meets Mil Spec #907E.

Complete chain and sprocket replacement packages.

• JT steel sprockets
• EK SR06 O-ring chain

A set of three OEM Suzuki front sprocket bolts. Thread-lock compound has already been applied for extra security.