Our offices will be closed on Monday, September 1 for the Labor Day holiday. We will be back on Tuesday, September 2 to process your orders and respond to your inquiries.
B&B Engineering Bash Plate for the CRF250L is made from 5083 4mm aluminum plate. Chosen because of its suitability for welding and extreme abrasion and impact resistance, this plate will protect the valuable center cases and deflect items away from the side cases as well. This plate is supplied with the necessary stainless clamps and bolts where necessary as well as foam or rubber where required.
Protect your frame/paint from scuffs and scratches with frame guards. The DRZ 400 frame guards are made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.
Replace your worn clutch plates and springs to reduce fade and slip.
All in one package.
We suggest adding a set of HotCams camshafts and a new clutch kit for the best results.
You will need to tune your EFI with something like the Power Commander V to get the most out of your Big Bore kit.
This will not fit the DRZ400 kick start models. Nothing is available for the kick start models.
This is a completely rebuildable stroker crank (3mm additional stroke) turns your mild mannered 250cc motor into a 263cc trail shredding monster! OK, maybe not, but sure makes it a fun machine.
Want the COMPLETE package? Order a Big-Bore kit to go with your stroker! That will give you a 308cc ripper! That is 24% larger than the stock 250. This package includes the Athena Big Bore Kit plus the 3mm Hot Rods Stroker Crank with new Genuine Yamaha crank bearings.
You will need to tune your EFI with something like the Power Commander V to get the most out of your Stroker kit.
For stock bore Hot Rods highly recommends you use the Vertex Stroker Piston Kit.
A high quality cam chain from the folks at Wiseco. New cams, big bore kit, high-mileage motor, you might want to think about a new cam chain. Direct replacement for stock unit.
Stage 1: Excellent mid-range and top-end power increase. Uses stock valve springs and rockers.
Fitment Specs: Exhaust Lift: 8.7; Exhaust Duration at 1.00mm: 236°; Intake Lift: 9; Intake Duration at 1.00mm: 236°
Here's another item you might want to replace when you are changing out your front sprocket. Because of it's big back tire, the chain is further away from the center of the engine than most bikes. The engineers at Yamaha decided they had better support the end of the countershaft since it is cantilevered out there so far. They also figured they had better feed some oil out there as well. These Countershaft Seals keep that oil where it belongs, lubricating the countershaft outer support.
Leaking Base Gasket? Replacing your worn Rings? Here are the gaskets you need to put your TW200 top end back together after a tear down. Includes: Head Gasket, Base Gasket, Stud Gasket, Head Side Cover O-Ring, two Valve Cover O-Rings, Base O-Ring, Stud O-Ring, Rocker Shaft O-Ring, two Cam Chain Tensioner O-Rings, Intake Manifold O-Ring, two Valve Stem Seals, and Exhaust Gasket.
Changing your countershaft sprocket? Here is the gasket you need for the left hand side case cover of your TW200. This is the same side of the engine as your gear shift lever and chain.
Kit includes all seals in the TW200 engine (including crank shaft seals) except valve stem seals. These are high-quality seals made in the USA.
Works Connection Billet Plugs for your left side case. These blue plugs includes both the timing mark plug and the crankshaft access plug.
DRC is one of the leading manufacturers of silicone hose kits for motorcycles.
Keep yourself COOL with a set of Moto Hoses. Moto Hoses are what you need to handle the heat that your bike is putting out whether you're pushing it to the limit or just stuck in slow city traffic.
Each Kit Contains:
10mm diameter - Includes three valve shims of each size from 1.85 to 3.20 in .05 mm increments. 84 shims in total, 83 cents per shim!
Direct replacement for old or broken stock spark plug caps.
Spark plug caps contain a resistor that can burn out with age. Fresh caps ensure your motor gets a strong spark.
B&B Off Road Engineering Fender Brace is made to help support your front fender/guard. Also helps support and reduce fatigue from constant vibration.
Made from 4mm 5083 structural aluminum plate. If you wanted to carry a small tool bag this would be a perfect product to support the weight and strap the bag to.
Fits on top of the fender and bolts between the fender and bottom triple clamp. Requires you to drill one hole in the fender for mounting.
Complete set of 'Adventure' wheels. These are the same rim sizes as used by the BMW GS and other big adventure bikes. The 19" front and wide 17" rear will give you great twisty road handling on the pavement while still being dual-sport friendly.
We start with silver Excel or Sun rims, OEM hubs and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.
Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
This nice piece replaces your plastic sprocket cover and protects your engine case from a chain derailment or failure. The 3/16" (5mm) thick steel plate is adjustable to accommodate 14, 15 and 16 tooth sprockets. Includes mounting hardware.
Replace your lost or broken stock plastic chain guard with a JNS aluminum one. Laser cut, CNC formed, TIG welded, and powder coated a beautiful satin black. This is a direct replacement for the stock unit.
Please note that this unit is a bit wider than the stock one and will have to be trimmed if you are running a big fat SuperMoto wheel/tire.
The Moose Axle Wrench combo for your DR has a 19mm for the front, and a 24mm for the rear. At 7½" long, it is long on leverage but, short enough to fit in even the smallest tool kit.
By simply replacing a motorcycle's stock shock linkage with with a longer, stronger and lighter DeVol Lowering Linkage, a bike's seat height will be dramatically lower to help give those riders with shorter inseams a more confident and enjoyable ride.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Kouba lowering link will lower the rear 1.75". Comes with bearings and seals installed for a quick and easy installation. Instructions included. WILL NOT FIT THE CRF250L RALLY OR CRF300L.
Precision tolerances – The tightest in the industry. Ultra-lightweight, for reduced unsprung mass. Straight rate springs will give better control.
Sold in pairs.
Progressive springs offer a soft initial spring rate for a plush ride. Progressively wound design provides increased resistance to bottoming as spring compresses. These springs are significantly stiffer than the wimpy stock springs.
They will make a big improvement in front fork action while still delivering a smooth ride. Sold in pairs.
The complete fork upgrade kit - Race Tech springs and emulators. Also includes a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
Tired of your mushy front suspension? ProCycle now offers heavy duty fork springs for the TW200!
Includes material for spacers.
Stock Spring Rate is .50 kg/mm. The .60 kg/mm springs are 20% stiffer than stock while the .70 kg/mm is 40% stiffer than stock.
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.
OEM spring rate is .46kg. We offer stiffer spring rates from -5% to 10% for riders who wish to carry luggage or just prefer stiffer suspension.
5% Less than stock
Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.
Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward.
Simple to install and completely tunable for all conditions and rider preferences.
Includes all components needed to rebuild you forks.
This 'Bling Ring' replaces the two stock preload/lock rings. The ring is CNC machined aluminum with the additional thickness to provide superior support on the shock body.
The added needle bearing thrust washer will make preload adjustments much easier. The ring then spins much easier against the spring making adjustments quite a bit easier.
To install the Bling Ring on a Cogent or Race Tech Shock Shaft Assemblies, it must either be disassembled or have the lower clevis removed.
Cogent Dynamics takes a stock DR650 shock, tears it down, cleans it up, adds a hard ceramic coating, then rebuilds it with a completely new custom shim stack that gives you excellent rear wheel control.
This custom Cogent valve stack makes this shock behave much like the Cogent Shock Shaft without the rebound adjustment capability. Providing a greatly improved suspension feel over stock at an affordable price.
Spring not included, sold separate.
Recommended spring rates:
This shock includes the Bling Ring preload adjusting ring AND the Thrust Bearing! This replaces the two stock preload/lock rings. This ring is CNC machined aluminum with the additional thickness to provide superior support on the shock body.
This option is ideal for those who desire the least amount of down time to install this suspension upgrade.
This kit includes a core charge that allows us to ship your new shock before we receive your stock shock core in 'good' condition. More details regarding core exchange linked below.
Lighter and stiffer than stock, these high quality straight rate springs are custom made specifically for the TW200. No adapter is needed! A proper rear spring will give a smoother more controlled ride. No more bottoming and better traction and confidence off-road.
If you (with all your gear on) weigh up to 220 lbs, you want the 15 kg/mm spring. 225 lbs and up will want the 19 kg/mm spring.
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.
OEM spring rates are 7.7kg on early models and 8.2kg on later models. We offer stiffer spring rates from 5% to 25% for riders who wish to carry luggage or just prefer stiffer suspension.
5% More than stock
The Pro-Series is the suspension performance pinnacle. Cogent takes Mojave’s best-in-class performance and adds an external reservoir.
The Pro-Series’ sophisticated reservoir with interchangeable valves and shims, provides more tune-ability at all speeds. It also improves internal pressure balance and temperature dissipation, giving long lasting performance regardless of the punishment you put it through.
Comes standard with the CNC machined Bling Ring Preload Adjuster Collar and a thrust bearing between the adjuster ring and the spring making preload adjustments easy.
The optional Hydraulic Preload Adjuster makes it even easier to adjust the preload. Just twist the knob. Includes mounting bracket for knob unit. (See last image) (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)
Select the spring you want installed based on the load you plan to carry. *Spring color may vary due to specification requirement and availability.
For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring.
If you regularly have more than 250 pounds on the bike, you might want to use the 8.15 kg/mm spring.
Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.
Replace those worn-out and high-priced stock KTM swingarm bearings with this swing arm bearing kit from Moose Racing.
Repair kit includes all the bearings, seals, shafts and spacers required for a complete rebuild.
Constructed from OEM-quality components at a fraction of the cost.
Complete Swingarm Bearing kit to replace the bearings and seals in the WR swingarm pivot.
| Description | QTY per Kit |
|---|---|
| Needle Bearing | 4 |
| Needle Bearing Shaft | 2 |
| Seal | 4 |
Complete kit to replace the bearings and seals in the WR shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Seal | 8 |
| Needle Bearing Shaft | 6 |
| Needle Bearing | 5 |
The little WRs have decent shocks but it can surely be improved with a Rear Shock Gold Valve from Race Tech. This will improve the damping in both directions and make the clickers more responsive to adjustments.
The stock sprocket retainer will rub the chain when it is used with 13 and 14 tooth sprockets.
We have our own sprocket retainer laser cut from 13 gauge stainless steel. This retainer works with all 3-hole 13T, 14T, 15T and 16T DR650 countershaft sprockets.
For reference, the stock gearing for the WR250R is 13/43 while the X model runs with a 13/42 stock configuration because of the SM wheels/tires. Both use a 108 link chain with the stock gearing.
The JT rear sprockets listed are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Limited availability on Aluminum from PBI. Manufactured from aircraft 7075 T651 Plate Aluminum.
If you want the additional low-end grunt that the 46, 48 or 50 tooth rear sprocket will give you, you will need longer chain as well.
New Rear Sprockets require new Sprocket Bolts because of a difference in the holes vs. the stock bolts.
Reduce the friction dragging down your drivetrain. This chain roller is made from Delrin®, it's self-lubricating and a significant improvement over stock.
Does not use a bearing but rides directly on the frame boss. There is no mounting hardware included.
The Moose Racing is a quality chain roller with 2 sealed ball bearings. The stock roller has no bearings. It's just a plastic wheel riding on a bolt. Ball bearing chain rollers are smoother, quieter and last longer.
This kit will replace your stock sprocket bolts, nuts and keepers with new hardware.
Many aftermarket sprockets are thinner where they bolt to the wheel and the threads on the stock bolts do not allow these sprockets to be tightened down all the way. These grade 10.9 bolts will alleviate that problem. They are the same length as the stock ones, but the threaded area is longer allowing stock sprockets or aftermarket sprockets to be securely tightened down.
The bolt keepers are genuine Yamaha replacement parts to ensure an accurate fit. It's a perfect upgrade if your keepers have been removed too many times.
A fresh set of brake rotor bolts. These bolts already have thread lock compound applied to the threads.
Stock OEM works with factory rotors, comes in a pack of 6.
For aftermarket rotors like Warp 9 or EBC front and rear sets are available.
Front comes in pack of 6
Rear comes in pack of 4.
Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.
Rotors are laser-cut from high-carbon content 410 stainless steel then lap cross hatch ground and heat-treated. The finished rotors are mounted on a floating black steel carrier for durability and strength.
The oversize floating pins are CNC machined stainless steel rivets with stainless wave washers to ensure they will not crush as more traditional steel pressed rivets can. Finally, high-temp paint is applied to surfaces like cooling holes and edges to provide a clean, finished look.
Includes a fresh set of brake rotor bolts.
Warp 9 320mm Supermoto front brake rotor kit. Newly updated and stronger.
Adds serious stopping power to the DR. Included is a new rotor floating on a central mounting carrier along with a caliper relocation bracket.
Available add on options include a Galfer braided stainless steel brake line, and 12oz bottle of Bel-Ray DOT4 brake fluid.
Includes a fresh set of brake rotor bolts.
Quality components at a great price.
More range at a great price. Choose the 2.7 gallon tank for the KLX250S in Black, Green, Natural or White.
This tank will NOT fit the 2009-2015 models.
More range at a great price. Choose the 2.6 gallon tank for the newer KLX250S in Black, Green, Natural or White.
This tank will NOT fit the 2006-2008 models.
Includes all necessary o-rings and diaphragms
This chain lube comes in a squeeze-tube bottle with an integrated brush nozzle. It makes applying chain lube easy and less messy than spray on lubes.
The Warp 9 shift lever is black anodized and the Warp 9 logo is laser etched into the finish. Comes with a black anodized knurled aluminum tip that folds and returns via a stainless-steel return spring. Includes the pinch bolt as well.
This bracket mounts between the frame and your right footpeg bracket (works with both stock and low mounts) and allows you to adjust the slop out of the stock system.
Places the pedal in the ultimate location for immediate brake activation and eliminates unwanted pedal motion.
Kit includes plate, adjuster bolt with lock nut and instructions.
Centerstands may impede the proper operation of this bracket.
Steel cargo rack from Moose Racing. It features a nice wide platform and a durable powder coat finish. 17" wide and 10" long.
Simple, quick installation of this 1 pound rack made from rugged 1/8" 5052 Aluminum. A rigid 4-point mounting system, but still sleek and low allowing for seat removal with no hassles.
Features:
Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.
The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary hardware is included. 10.5"Wx11.5"L
Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets.
Renthal chain lube is 100% lubricant, zero propellant. So this new 250ml bottle size combines high performance and value.
The all-new formula Chain Lube is specially designed to penetrate all parts of the chain. This all-condition lube is compatible with all o-ring and non o-ring chains.
Designed for use with stock engines using either stock or aftermarket exhaust and air filters.
We all love our TWs, but the stock jetting leaves much to be desired! Here is a Jet Kit for your stock TK carburetor to improve your throttle response. Included in the Kit are a wide range of main jets to cover any setup, one Pilot Jet, one Jet Needle, and five Needle Shims. If you have added an exhaust system or ride at higher elevations, this is a great way to tune your TW for your needs.
This is a new Diaphragm Set for your 1987-2000 TK carburetor. If yours has cracked or ripped, here is a replacement.
The Power Commander 6 fuel injection tuning device allows you to optimize your fuel and timing curve (where applicable) giving you the confidence to roam freely. With fine tune adjustability and multiple inputs, the Power Commander 6 will keep your vehicle running at its full potential letting you concentrate on the journey ahead.
Featuring a plug-and-play setup, Power Commander 6 can be installed discreetly underneath your seat, cowl, dash or other location ensuring your ride looks as good as it runs. Removing the device reverts your vehicle completely back to stock. With the ability to store and switch between two maps on-the-fly (via the map switch accessory) and connect to various Power Commander accessories such as the Autotune, Quickshifter or POD-300, the Power Commander 6 gives you features and functions that provide you with the ultimate ride.
All PC6 models have an end-user adjustment of +/-15 in the FUEL table and +/- 8 in the timing table (if applicable). This adjustment is on top of the values that are in the BASE map loaded to the device. This BASE map can be any of the available maps from the Dynojet website, or those you may have received from a third party.
Thick, flat foam, greaseless sealing ring ensures maximum contact with your airbox while acting as a breathable gasket for increased air passage
Features:
Genuine Honda replacement air filter.
Yamaha uses this seal material in many places on several motorcycles. It is like weatherstripping and is used to seal up the edges in the TW200 air-box. It seals up the air-box so that water and grime can't enter the air-box from the side. Ensures that air entering the box comes from up under the seat.
Hiflofiltro air filters are manufactured to fit the factory air box and are a direct replacement for original equipment filters.
Top quality powerflow filtering media, developed for modern high performance engines.
Better throttle response. More power over a much wider range.
Kit includes pre-jetted genuine Mikuni TM36 Pumper carb and push/pull throttle cables. Everything is included to mount this carb to your bike. Well suited for stock to mildly modified motors.
Low peg mounts for the DR From Wirtz Wire. These are different than our other mounts for several reasons. First, these are designed around the stock pegs. All of the pegs in this section will fit these mounts. Another difference is that these mounts are offered in a low mount as well as a low and rearward mount. These are 'wire EDM' machined from solid 1018 steel bar stock, and are not welded anywhere. They are powder coated black for a great look. Both mounts move the pegs down 2" while the low and rear mounts also move the pegs back 1.3".
Kit comes with new mounts, longer bolts and a longer brake switch spring that will be needed. Pegs are optional, your stock pegs will work.
The upper image shows the low and rearward mounts while the one below that is of the just low mounts. If you look at the two images below that, you will see that these are the low and rearward pegs for both sides of the bike.
The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option.
Wider foot pegs for sure-footed comfort.
17-4 cast stainless steel.
| Width | 1.97" |
| Length | 3.18" |
Second image shows the Super Stock peg next to the stock bird perch.
A set of six high quality grade 10 sprocket bolts with lock nuts. Thread-lock compound has already been applied for extra security.
These bolts are flat head style, requiring a countersunk hole in the sprocket.
This is a genuine Suzuki part. We recommend installing a countershaft seal retainer to prevent the countershaft seal from popping out while riding.
This gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. Get a fresh one now to ease installation of your new performance muffler.
This gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. Get a fresh one now to ease installation of your new performance muffler.
This gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
The science behind the MegaBomb header may be FMF's greatest engineering accomplishment to date. You can bolt on a MegaBomb with an existing FMF Racing slip on for as much as a 3hp boost, plus the MegaBomb actually reduces noises levels by as much as 1.5dB. The MegaBomb technology is evolved to produce more low end to mid range gains as well as broadening out the mid to top end power gains over stock. MegaBomb is the next level technology you can have today.
For FMF mufflers only
Since Kawasaki brought back the popular little KLX250 with updated fuel injection, Yoshimura brought back an updated RS-2 slip-on that now incorporates an o2 sensor that accommodates the new fuel injection technology on the KLX. All of that with added power, torque and that distinct Yoshimura exhaust note.
Entire unit is proudly made in the good old US of A to boot!
The product that you are purchasing is designed and intended for closed course competition use only and is labeled as such, i.e. Yoshimura "RACE SERIES." Yoshimura RACE SERIES products are neither designed nor intended for use on PUBLIC ROADS or LAND. Such use is prohibited by Federal and State regulations.
Use this installation tool from Cogent to be sure that your Cogent Drop-in Dynamic Cartridges are installed correctly. A strong magnet in the end holds the cartridge firmly while you lower it into your fork leg. Then slide the spring over the tool until it holds the DDC down, then gently remove the tool. That simple. Never again question if it is properly seated on the damper rod.
Works equally well for removal when you need to change your fork oil. Also works great with Race Tech Emulators.
New wider seat to help keep comfortable on that long commute or dual-sport ride. The added width and foam density will help keep the seat from being an item to stop you from going on that ride or enjoying the bike.
Each kit contains detailed instructions for easy "Do It Yourself" installation. This provides the highest level of quality & comfort at an affordable price.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
The Foam and Cover Kit is only for the OEM pan. It DOES NOT include the pan.
Only Available in Tall; All Carbon Fiber
| Width: | 9.5" (241mm) |
| Height | 1" (25mm) TALLER than the stock seat |
Recover that shredded or uniquely colored stock seat cover with this OEM black cover. This includes only the cover material (grab strap is no longer available). Designed to fit over your stock seat pan and foam.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail / stop light function. 3 white LED's are used for license plate illumination.
Included is a set of turn signal brackets that bolt to the mount, but these are designed for a smaller LED type signal with a mounting stud of just 8mm. Or consider the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!
NOTE: LED's must be installed on a 12 V DC system!
Clean up the backside of your TW200 and upgrade to a brighter, safer LED taillight in one go!
The Tidy Taillight Kit includes a durable, high-quality steel mounting bracket that mounts under your rear fending using the existing bolts. The bracket also has slots to mount your license plate.
The included LED taillight helps make your TW more noticeable to other drivers at night, and the super-bright LED brake lights activate more quickly than stock incandescent bulbs when you get on the brakes, giving drivers behind you more reaction time. The taillight unit also features white LEDs on the underside to light up your license plate and keep you legal.
This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, no drilling, no wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.
This kit is available with either a chrome or black chrome reflector in the headlight.
Does not fit '87 TW200 because that year has a unique AC powered headlight circuit.
Stock chain guard crack and crumble on you? Won't happen to this unit CNC machined from 2.5mm marine grade aluminum. Polished to a beautiful sheen that will give your DR that little twinkle as well as better protection.
Here is the little switch that mounts inside your brake or clutch lever perch and controls the brake light or clutch safety circuit. This switch often gets damaged in an unplanned dismount (aka: crash) or the plastic simply cracks from age. When this happens, you can find yourself chasing a short circuit that keeps blowing your fuse every time the brakes are applied. If this has happened to your TW, here's the fix!
The 12oclock Labs EXUP Emulator is used in place of the stock exhaust servo motor when you replace the stock exhaust with an aftermarket exhaust system. The microprocessor controlled EXUP, emulates the exact characteristics of the stock exhaust servo motor and its motor delay sweeps, keeping the ECU from displaying the dreaded check engine light. Weight is less than 1/2 an ounce and it is a direct plug and play replacement.
If you are looking to swap out your stock CDI box, the Big Gun Rev Box is an affordable alternative to highly-priced OEM replacement boxes. It increases the overall RPM limit over the stock box and advances the timing curve and is a direct plug-in replacement.
You must cut the green wire on the 8-prong plug going into CDI box.
