This kit includes 2 needles that have been developed by JD Jetting and manufactured for them to their exacting specifications. These two needles allow a wide range of tuning possibilities and provide correct fuel delivery at any throttle position.
4 Allen type screws for the float bowl are also enclosed should you strip out the stock screws during your tuning process. Complete instructions with photos, jetting suggestions for different set-ups and situations, 4 Main Jets, a new Pilot Jet, and a drill bit complete the package.
Designed for use with stock engines using either stock or aftermarket exhaust and air filters.
The Power Commander 6 fuel injection tuning device allows you to optimize your fuel and timing curve (where applicable) giving you the confidence to roam freely. With fine tune adjustability and multiple inputs, the Power Commander 6 will keep your vehicle running at its full potential letting you concentrate on the journey ahead.
Featuring a plug-and-play setup, Power Commander 6 can be installed discreetly underneath your seat, cowl, dash or other location ensuring your ride looks as good as it runs. Removing the device reverts your vehicle completely back to stock. With the ability to store and switch between two maps on-the-fly (via the map switch accessory) and connect to various Power Commander accessories such as the Autotune, Quickshifter or POD-300, the Power Commander 6 gives you features and functions that provide you with the ultimate ride.
All PC6 models have an end-user adjustment of +/-15 in the FUEL table and +/- 8 in the timing table (if applicable). This adjustment is on top of the values that are in the BASE map loaded to the device. This BASE map can be any of the available maps from the Dynojet website, or those you may have received from a third party.
Thick, flat foam, greaseless sealing ring ensures maximum contact with your airbox while acting as a breathable gasket for increased air passage
Features:
Genuine FCR-MX Carburetor Rebuild Kit
Not for the stock BST DR650 carburetor, Fits FCR-MX conversions Only
Genuine Honda replacement thermostat
Keep yourself COOL with a set of Moto Hoses. Moto Hoses are what you need to handle the heat that your bike is putting out whether you're pushing it to the limit or just stuck in slow city traffic.
Each Kit Contains:
Works Connection Billet Plugs for your left side case. These blue plugs includes both the timing mark plug and the crankshaft access plug.
This kit provides much of the performance gain of our 130 kit but keeps you legal for racing classes that do not allow motors over 125cc.
Our kit includes 5 EBC friction plates which eliminates the judder spring assembly by replacing it with a 5th friction plate.
Heavy duty clutch springs by Barnett are included it this kit which will significantly decrease wear under high stress conditions.
Includes genuine Honda friction plates, drive plates, and clutch springs.
The Dirt Racer Complete Clutch Rebuild Kit is the ultimate package for your Yamaha, here's why:
'Stack Height' is the all important factor when renewing a clutch and riders are always best to buy a complete kit instead of separate single plates as sold by manufacturers. Replacing just the worn plate (or plates) may not even get close to rebuilding your clutch to its original stack height and all you get is clutch slip and the job has to be done again.
Since 1948, Barnett clutch plates and springs have been made from the finest materials available.
Replacement friction plates and drive plates.
Heavy duty springs help prevent clutch slip in high-performance motors.
Designed to improve the life and durability of your clutch, Barnett's "Dirt Digger" provides better rideability with less slippage compared to stock.
Includes all necessary top quality gaskets for top end rebuilds.
High quality stator cover gasket.
This kit includes the large O-Ring that goes on the end of the filter and the small O-Ring that seals the hole just above that. Both are factory Yamaha parts.
Choose standard bore top end, big bore top end or a complete gasket set for the standard bore motor. These are high-quality gasket sets from Athena.
Top end gasket set with the addition of a factory Suzuki metal base gasket. A metal base gasket is essential because paper base gaskets will fail in the DR650.
Genuine Honda replacement oil filter cover gasket.
You will need to tune your EFI with something like the Power Commander V to get the most out of your Big Bore kit.
Providing unbeatable performance and exceptional value, Hiflo filtro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
Grab our 5-pack and save both time and money!
Providing unbeatable performance and exceptional value, Hi-Flo is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide.
Grab our 5-pack and save both time and money!
The Complete Top End Performance Kit includes:
10.5:1 compression JE piston with rings, wrist pin and circlips (the actual measured stock compression is only 8.7:1).
Stage 2 Web Cams high performance camshaft for more power (reground from brand new OEM Suzuki camshafts).
Top end gasket set with metal base gasket.
We strongly recommend checking valve to piston clearance when installing a non-standard camshaft.
Raises compression from stock 9.5:1 to 10.5:1 for more power, torque and snappier engine response. The high quality forged piston from JE is almost a full ounce lighter than the stock cast piston. This makes for less vibration and a smoother running motor. Includes rings, pin, clips, and top end gasket set with valve stem seals and metal base gasket. Fits the standard size stock bore.
Designed to enhance mid-range and top-end power. Manufactured using the highest quality standards. No core required.
Note: This camshaft has been designed to work with the OEM Yamaha piston, or the BBR big bore kit piston, with OEM sized valves. Any other combination of parts will require that you manually check valve to piston clearance.
Bolt on horsepower! Stage 1: single-cam motor. Excellent midrange and top-end power increase. Uses stock valve springs and rockers.
Fitment Specs: Exhaust Lift: 5.9; Exhaust Duration at 1.00mm: 223°; Intake Lift: 6.8; Intake Duration at 1.00mm: 227°
OEM throttle cable set for the CRF250L
*generic image, actual cables may look different.
Handlebar mounts that replace your stock clamps.
These raise your handlebars 1 inch.
Available in 7/8" for standard handlebars allow installation of your choice of 7/8" off road handlebars.
This adapter will give you more mirror choices.
Yamaha mirrors have reverse threads on the right (throttle) side of the handlebars. This adapter allows you to mount a mirror with standard 10mm threads on the right side of your handlebar. This opens up many options for your mirrors, choose any 10mm mirror for your Yamaha.
The glove box for your motorcycle! The Zigzag handlebar bag is their smallest bag yet also one of their most popular. Sometimes you only need the basics like your wallet, phone, registration, and other small items, and no matter what you’re riding, the Zigzag handlebar bag delivers quick and easy access to the basics.
This beautiful polished rear carry rack from B&B Eng. is made from aluminum tubing and 4mm 5083 plate. 5083 is used because of its suitability for welding and high level of abrasion and impact resistance. Kit includes all the necessary stainless clamps and bolts. With the roundness and strength of the tubing supports, it makes a great grab handle when you need to lift the rear of the motorcycle.
Pro Moto Billet Cargo Racks are brutishly strong, functional, and they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum. Available in silver only.
Note: Placement of this top rack does require removal of the stock tool bag.
A small light-duty Dual Sport Rack for the WR. Precision laser cut from 3/16" 5052 aluminum. It is powder coated black with a shot-peened look. This rack is 9" x 10.5" at widest points and has numerous tie points for straps or bungees. It's pre-drilled for a RotopaX mount. Easy installation means it is bolted to the bike in about 10 minutes. There is some minor drilling of the plastic to be done. All necessary hardware and complete instructions included.
The Dakar pack has been designed for those rides where you find yourself a long way from home. Offering enough storage (22.5L) and versatility for the true adventure rider, the Dakar pack has a number of internal organized pockets for all your gear, whilst still maintaining enough free storage space to maximize flexibility. Durable 1680D waterproof fabric construction ensures the Dakar is up to the task of long endurance rides.
The unique multi-tier external pocket system gives you quick access to any compartment without having to loosen off the entire pack every time. Internal to the pack is a fully padded AV pocket with cable ports for external cable routing, a soft-lined goggle pocket and a vented mesh breathable storage pocket. The Dakar pack would not be complete without the Source Widepac 3L hydration system and the CE certified Level 2 removable back protector supplied.
Construction 1680D Poly Fabric
– YBS water resistant zips with rubberized all weather pulls
– CE Level 2 Back Protector EN 1621-2
– Capacity 22.5 lt
– Removable waist belt and Shoulder harness
– Nine (9) storage pockets
– Shark Fin air flow optimized back padding
– CONFIGR8 ladder lock adjustment system (tool free)
– 3lt hydration system
– Weight 4.3 lbs (With pack shield and hydration system.)
– Weight 3.3 lbs (Pack only).
– Length 19.5″ – Width 11″
– Multi Tier external access stowage.
– Durable Duraflex buckles
The Speedo DRD corrects and fixes the speed signal after it was altered by something else, such as sprocket changes or tires size changes or transmission changes.
The Shorai LFM Standard Recommendation is the best overall pick for most applications, and has been selected to give strong cranking performance and long lifespan.
Measures 4.5" x 3.5" x 2.28"
Weight (lbs): 1.34 lbs
Weight (kg): 0.61 kg
Cold Cranking Amps: 135
Polarity: [- +]
Each Shorai battery includes self-adhesive foam panels to achieve a snug fit in your battery box.
The TAPP™ is a compact, easy to mount, all weather 2.1amp USB Power Port and is the answer for powering and charging your USB devices including cell phones, smart phones, most GPS units, MP3 players, and most digital cameras.
Quick charge 3.0 technology provides fast charging for Android devices with Quick charge capability. Charging power levels up to 18 watts contrast with the USB standard maximum charge power of 10 watts.
TAPP™ 2.1 Amp Weatherproof USB Power Port With Quick Charge 3.0 Technology
Fits Honda CRF450L Motorcycles (Front Turn Signals)
OEM Fit Left Front and Right Front turn signal connectors with wires pre-attached.
This kit is specifically for attaching After-Market turn signals to the front of the CRF250L / Rally or CRF450L.
Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.
White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.
Dazzling bright Amber blinker functions.
All in a spring-loaded stock to prevent damage from a tip over, crash or impact with brush, trees etc. They will bend 360 degrees, but are stiff, durable and nearly unbreakable.
Yamaha T7 Specific plug and play kit using factory connectors, flasher and block off plates included.
Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.
White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.
Dazzling bright Amber blinker functions.
All in a spring-loaded stock to prevent damage from a tip over, crash or impact with brush, trees etc. They will bend 360 degrees, but are stiff, durable and nearly unbreakable.
Suzuki DR650 Specific plug and play kit using factory connectors, flasher and diode kit included.
Years in development, Yenkro Adventure Rally Fairings have been designed from the ground up to withstand even the most unforgiving terrain and now the gen 2 kit takes it to the next level. Battle-tested in conditions that only the Australian outback can muster, this fairing is a must for adventure riders from all corners of the globe.
Side Panels are Optional and Sold Separate, they work with Acerbis 6.6 gallon (25L) tank only. Available in either black or white.
Can be purchased with or without side panels.
Standard kit includes:
The standard lighting kit is a pair of Hella 60mm projectors, one for high and one for low, these are 60w halogens and are DOT and ADR approved.
Two parts in one. Not just a cover over the countershaft sprocket, but also a case saver as well! Should you ever throw a chain, this will keep it from going into the engine cases and causing extensive and expensive damage.
Replace your lost or broken stock plastic chain guard with a JNS aluminum one. Laser cut, CNC formed, TIG welded, and powder coated a beautiful satin black. This is a direct replacement for the stock unit.
Please note that this unit is a bit wider than the stock one and will have to be trimmed if you are running a big fat SuperMoto wheel/tire.
A CNC machined Chain Guide that is considerably stronger than the stock plastic unit.
428 x 130 links. High Quality non-ORing chain. Rust-resistant gold plated chain for high powered racing machines.
Based on Advanced Ceramics, this compound is designed to deliver excellent performance in all aggressive scenarios. It offers fast heat recovery for more consistent braking which, in turn, gives the rider more "feel" and control. These pads are easy on rotors since they do not have the same levels of metallics in them as many O.E.M. and after-market brands.
Includes front and rear brake pads
Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam. On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as similar to stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.
This is a high-quality seat cover kit by Moose for the XR650L. This is a direct replacement seat cover only. No seat foam, and you install on your stock pan with existing foam. Heavy duty marine grade vinyl, and UV protected for long life. Double stitched for durability. Available in Red or Blue.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
This gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm.
Hose reducer to go from 5/16" line down to 1/4" line. Many bikes have 5/16" carburetor spigots but most aftermarket petcocks are 1/4". This solve the problem of mismatched sizes. Solid brass construction. Can be used to route or repair fuel lines, oil lines or air lines. Barbed ends provide a secure fit.
A replacement gas cap for your IMS tank. Newly redesigned to resist damage from new fuel additives that were hard on the seal in the old style cap.
B&B Off Road's Honda CRF250 Rally bash plate is made from 4mm aluminium 5083 plate. This grade of aluminum is chosen because of its extreme suitability for welding and abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All bash plates are supplied with the necessary stainless clamps and bolts where possible. All bash plates have a polished finish and have foam or rubber where required.
Bash plate is installed after first removing the lower OEM plastic bash plate/fairing.
Their best selling product to protect your bike, Flatland Racing skid plates are made from 5052 3/16" aluminum plate.
They are all hand tig welded together with side engine guards. Installation is easy with our clamps that grip tight.
Their skid plates offer clean out slots and oil plug hole, making oil changes simple. These are more durable than carbon fiber and plastic.
Mounting hardware and instructions included.
The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike. Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.
Features:
Available in 2 colors
Protect your frame/paint from scuffs and scratches with these great Frame Guards from B&B Engineering Made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.
THE MOST ADVANCED RADIATOR PROTECTION SYSTEM AVAILABLE FEATURES
1. Maximum side and front impact protection-Using a combination of CNC machined 6000 series 3 dimensional aluminium extrusion and 5000 series alloy plate we have created a system to protect your rads from virtually every direction
2. Maximum roost and debris protection- Due to the angle fin design there is very little of the radiator core and veins that are directly exposed to roost, debris and trail side sticks
3. Maximum airflow -B & B’s unique aluminium front louver panel constructed from high strength extrusion allows 3 dimensional fins to be incorporated into the design to mimic the airflow characteristics of the genuine plastic fins
4. Removable finned louver panel- Front panel only requires 2 bolts to be loosened to allow for easy removal for cleaning
5. Integrated modular construction- Three piece modular construction allows for greater design flexibility eliminating the compromises inherent with one piece designs
6. Easy fitment no mods required- Guards can be fitted in approx ½ hour using basic tools
7. All parts available individually- If you damage any part of the radiator guards, B&B's design allows you to purchase only what you require.
XT250 engine Case Guards.
These are a very nice addition in engine protection for the XT250. Made from billet aluminum and steel powder coated bracketry.
A 10-pack of drain plug sealing crush washers. Replace your sealing washer at every oil change to prevent a leak.
TW200 billet oil drain cap plug.
Nice billet aluminum replacement for the old cast oil drain cap.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 2 |
Complete set of custom made Buchanan's stainless steel spokes with blue zinc plated nipples. Includes enough spokes and nipples to lace up one wheel.
Required information needed when ordering:
(Please provide this information in the comments section when placing your order)
1. Year, Make, Model
2. Is your wheel and hub OEM or aftermarket?
3. Size of your rim
Contact us before removing your wheels as some bikes will need measurements taken before spokes can be ordered.
For easy removal of recessed oil filters.
Conical point screws pierces and grabs the metal end cap of the filter.
reduces potential damage to the engine cases.
NOT for use on re-usable oil filters.
The easy way to lubricate the cables on your motorcycle. Lubricates completely in five seconds!
Features:
The MotoPressor is a compact pump unit that weighs only 1.3 pounds and fits in the palm of your hand! Measures 4"x3"x1.5" This makes it smaller and easier to carry with you.
It includes a 8 inch long inflation hose, with a a low air loss chuck. You also get an SAE power cord that attaches to your battery and stays there, along with alligator clips with SAE connector. The Pocket Pump has an 6.5 foot power cord. All of this packs into a heavy duty neoprene pouch.
MotoPressor will inflate a 150/70/ R18 tire from 0-31psi in under 4 minutes, and is capable of pumping up to 130psi. It also features a built-in cooling fan to keep the pump at optimum operating temperature, and a check valve to check the psi by attaching your tire gauge to this valve.
The MotoPressor Puncture Repair Tool combines the four tools essential for tubeless tire repair into a single tool.
With the motorcyclist in mind, they've designed a "4 in 1 multi-tool" that uses pre-vulcanized repair strings and packs into a sheath measuring a mere 130 x 68 x 50mm, that's small enough to fit in your pocket. The tool contains a pair of pliers, a rasp, an insertion tool and a sharp knife, which is all you'll need to fix 99% of punctures. The repair strings are pre-vulcanized, so they've done away with the "little tube of glue". The repair plugs the hole AND leaves a "patch style" repair on the INSIDE of your tire.
If you'd like to see the tool in action go just click HERE, and watch the demo.
The aluminum part can be used as a valve core remover / wrench.
- Made of A6061 aluminum.
- Available in 6 beautiful anodized colors.
- Comes in pairs.
Lighter and stiffer than stock, these high quality straight rate springs are custom made specifically for the TW200. No adapter is needed! A proper rear spring will give a smoother more controlled ride. No more bottoming and better traction and confidence off-road.
If you (with all your gear on) weigh up to 220 lbs, you want the 15 kg/mm spring. 225 lbs and up will want the 19 kg/mm spring.
Custom developed by BBR Motorsports for the ultimate upgrade for mini four-strokes. Sized perfectly for adult back-yard racing or fast/aggressive mini riders. This is the most important upgrade you can make for an adult sized rider. The stock suspension is too soft for most adults and aggressive kids.
Precision tolerances – The tightest in the industry. Ultra-lightweight, for reduced unsprung mass.
Straight rate springs will give better control in the rough stuff. Sold in pairs.
Patented fork seal features a balanced 3 lip design that evenly distributes the pressure reducing operating temperature, wear and friction
Custom Elastomer Fork Seals have been tested to outlast OEM fork seals. Extends typical seal life by 3 to 5 times over OEM seals
Stiction (friction) measures from 1/3 to 1/2 less than OEM seals for smoother fork action
Lower Stiction, Longer Life! It doesn’t get any better than this!
Plus, the only complete line of dust wipers! Wipers should be replaced with the fork seals to assure peak performance.
Kit includes Fork Seals and dust wipers.
Patented fork seal features a balanced 3 lip design that evenly distributes the pressure reducing operating temperature, wear and friction
Custom Elastomer Fork Seals have been tested to outlast OEM fork seals. Extends typical seal life by 3 to 5 times over OEM seals
Stiction (friction) measures from 1/3 to 1/2 less than OEM seals for smoother fork action
Lower Stiction, Longer Life! It doesn’t get any better than this!
Plus, the only complete line of dust wipers! Wipers should be replaced with the fork seals to assure peak performance.
Kit includes Fork Seals and dust wipers.
GET JumpStarter Mini, the second-generation, multifunctional jump starter. Now lighter and smaller, it's ready to help you restart any motorcycle or scooter when the battery is low. You can also use the powerful built-in LED flashlight or charge your use it as a power bank to charge your electronic devices. JumpStarter Mini comes together with a hard, water-resistant case perfect for carrying it anywhere and protecting it on your journeys.
A Dual Compound radial for performance street riding.
Tread surface divided into three separate areas featuring two different rubber compounds.
Softer shoulder rubber provides phenomenal cornering grip.
Lean angle up to 51.2°
Tubeless and W rated (max speed of 168 mph)
Designed specifically for Dirt Drack racing for mini racers. Tread design can be customized to meet each rider's needs to provide superb traction and stability on any race track.
120/70-17
Not DOT approved for street or highway use!
This Clymer Repair Manual is an essential resource for anyone looking to service or repair their motorcycle at home. Whether you're riding at the weekend or using your bike for a daily commute, you don't want your plans disrupted - performing regular maintenance is crucial to keep things running smoothly.
Every Clymer workshop manual is the result of a full stripdown and rebuild, allowing you to really know the detail behind your bike. Alongside step-by-step instructions and expert advice, you'll find a wealth of images that help to guide you through repairs and servicing tasks, even on small and complex parts.
What's Included
(This manual's year range represents the years of coverage available when the manual was written. The vehicle or machine's production years may extend beyond these dates.)
With a Haynes manual, you can do it yourself…from simple maintenance to basic repairs. Haynes writes every book based on a complete teardown of the motorcycle. Haynes books have clear instructions and plenty of photographs that show each step.
Complete coverage for your Yamaha Trail Bikes covering PW, RT, TT-R and XT225/350 models for 1981 thru 2000.
Universal 3 bolt flywheel puller.
Complete with hardware kit and adapter for male or female removal.
We start with Excel or Sun rims, OEM hubs, and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.
Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
Time to freshen up your forks? Three pack or single 16oz bottles of Maxima fork oil that will refill your tubes after any fork job. This is a high-quality fork oil and what we use on our projects here at ProCycle.
For most situations you will use 10w Fork Oil. Some custom applications will use the 5w or 15w oil. Order the 5w oil if you have Ricor Intiminators or Cogent DDCs.
Introducing Oinker®, the revolutionary chain lube attachment for dirt bikes, street bikes, and ATVs. Say goodbye to messy lubrication. Oinker® attaches to any chain lube or wax, ensuring a precise and even application to both sides of your chain. This means minimal overspray, keeping your swing arm, rear tire, and brakes clean.
*For cans with an attached smart straw, you will need to replace it with the included nozzle
What's Included:
The high rigid and light weight design, provides better control of the rear brake.
The clevis body is made of A7009-T6 aluminum. Comes with a specially designed stainless steel pin.
