Search Products

Keep your smartphone, GPS and/or MP3 charged while enjoying your ride. Water- and weather-resistant, the Dual USB Port/Plug Charger offers you 5-Volt/2-Amp dual USB ports that have an inline fuse for protection. It comes with 38" of wire and 12" long battery quick connect rings. The mounting bracket that is included fits 7/8" and 1" bars.

A new high output stator for the XR650L. 25% more output than the stock unit. Approximately 50 additional watts. Now you can have enough power to run those driving lights and/or heated riding gear!

Made from strong and light 5052 aluminum to hold your license plate firm and up, out of the way for maximum tire clearance, prefect for your new dual sport bike.

It uses the original tag light with out any modifications to your bike. Mounting hardware and instructions included.

Quality replacement headlight fairing for TW200

Quality parts from Acerbis. Replace those big white ones with black ones for a custom look, or you can just replace your trashed white ones with crisp clean new ones for that great stock look.

Depending on your application and preferences, more than one optional heat shield may be useful.

There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.

You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.

• Plug and Play
• 7 Different Programmable Turn Signal Patterns (for demo video click here)
• Safety Brake pulsing built in (Can Enable or Disable)
• Superbright LED's; For excellent brightness, even in direct sunlight
• License Plate Light built in
• License Plate Bracket fits the common USA license plates, sloted for maximum plate compatibility.
• Includes Mounting Hardware
• Saves about 2 lbs over the factory tail light setup
• Made In the USA

We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.

This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.

This DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.

No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.

This kit is highly recommend over the non-DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!

Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.

• Low Beam: 20W, 2,800 Lumens
• High Beam: 35W, 3,600 Lumens
• Color Temperature: 6,000k
• DOT & SAE Compliant
• CE, RoHS, ISO9002, IP67

This kit includes a DOT LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.

How does this headlight compare to our original TW200 kit? First and foremost, this kit has SAE/DOT markings and a much wider/brighter high beam pattern. The low beam is very similar to our original kit: wide, flat, and bright but with more punch. The DOT headlight assembly has also proven to be more durable than the original headlight.

Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Approved
CE, RoHS, ISO9002, IP67

No cutting, drilling, or wiring modifications! Installation takes 5 minutes.

Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.

  Please note that this product is not compatible with the 1987 TW200.

Plug-In connector kit for your CRF. This kit fits Rally and Non-Rally Versions of the Motorcycle. Wires and terminals will come pre-attached with subharness.  

Plugs into the Aux Power connector. 
Harness length is 32" (2.66ft)

The Pro-Series is the suspension performance pinnacle. Cogent takes Mojave’s best-in-class performance and adds an external reservoir.

The Pro-Series’ sophisticated reservoir with interchangeable valves and shims, provides more tune-ability at all speeds. It also improves internal pressure balance and temperature dissipation, giving long lasting performance regardless of the punishment you put it through.

Comes standard with the CNC machined Bling Ring Preload Adjuster Collar and a thrust bearing between the adjuster ring and the spring making preload adjustments easy.

The optional Hydraulic Preload Adjuster makes it even easier to adjust the preload. Just twist the knob. Includes mounting bracket for knob unit. (See last image)  (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)

Select the spring you want installed based on the load you plan to carry. *Spring color may vary due to specification requirement and availability.

For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring.

If you regularly have more than 250 pounds on the bike, you might want to use the 8.15 kg/mm spring.

Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.

Cogent Dynamics Mojave product is a drop-in replacement for the DR650 stock shock, no modifications necessary. Mojave is not simply an improved Suzuki shock, it is a brand new replacement shock that is a totally engineered suspension solution to suit your needs.

Each shock is assembled and tested on the Cogent Dynamics suspension dyno before being packed up and shipped. Like its bigger brother the Mojave Pro Series, this will make an incredible difference in the handling of your DR.

Mojave Improvements over stock
Mojave upper mount: uses a precision spherical bearing with dust seals, which accurately transfers damping forces to the motorcycle frame.

Internal improvements: Cogent designed shaft, seal head, damper piston, adjuster and clevis.
Mono tube construction: precision honed, super-stiff steel body with an upper body cap machined from billet aluminum.
Built-in billet aluminum separator piston provides an in-line gas pressure reservoir which eliminates the Suzuki rubber bladder.

This shock package includes the CNC machined Bling Ring Preload Adjuster Collar and Preload Bearing that will make preload adjustments easy.

Select the spring you want installed based on the load you plan to carry. For riders (and gear) less than 250 pounds we recommend the 7.6 kg/mm spring. If you regularly have more than 250 pounds the bike, you might want to use the 8.15 kg/mm spring. If you have any questions at all about this, please call.

You may choose to add the Hydraulic Preload Adjuster to make it the easiest of all. All you do is twist the knob. Includes mounting bracket for knob unit. (Some CA carb compliant models may need slight modification for mounting the preload adjuster.)

Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.

Race Tech shock springs in a wide range of spring rates to dial in your rear suspension to suit your weight (stock spring is 5.3 kg/mm). Recommended spring rates:

• Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life
• Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material
• Triple-lip seal design
• Dyno-tested to last 3 to 4 times longer than OEM seals
• Directional ribs allow seal to be installed easily
• Kit includes fork seals and dust wipers

 The perfect option for the DIY'er.

The Cogent Dynamics Shock Shaft Assembly is ready for installation. The Cogent shock shaft also features an external rebound damping adjustment. Just what you need to have the ultimate in rear suspension control.

Does not include a spring. Compatible with both stock and aftermarket springs.

Requires 5wt shock oil

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.

DDC Tool will not work with this spring series

These Cogent Dynamic Drop-in Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.

DDC Tool will not work with this spring series

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. No disassembly of your forks, no drilling of damper rods. Just change the oil to 5w and install the DDCs under the springs and hit the trails.

Stiffer fork springs are required to realize the full benefits of the DDCs. Please call if you have any further questions.

The DDCs are not recommended for use with progressive springs.

The DDC Install/Removal Tool which makes installation that much easier.

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.

Stiffer fork springs are recommended to get the full potential of the DDCs.

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. No disassembly of your forks, no drilling of damper rods. Just change the oil to 5w and install the DDCs under the springs and hit the trails.

Stiffer fork springs are required to realize the full benefits of the DDCs. Please call if you have any further questions.

The DDCs are not recommended for use with progressive springs.

Add the DDC Install/Removal Tool which makes installation much easier.

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. No disassembly of your forks, no drilling of damper rods. Just change the oil to 5w and install the DDCs under the springs and hit the trails.

Stiffer fork springs are required to realize the full benefits of the DDCs. .42 kg/mm springs are the springs recommended for just about anybody out there. Please call if you have any further questions.

The DDCs are not recommended for use with progressive springs.

The DDC Install/Removal Tool which makes installation that much easier.

The Cogent Dynamics DDC valves are the most cost-effective upgrade you can make to your motorcycle’s forks. Unique and the first of its kind, a DDC kit is available to upgrade many motorcycles that are originally equipped with simple damper rod type forks as front suspension.

We do recommend stiffer than stock front springs to bring the full potential of the DDCs out. OEM springs are dual rate 0.45/0.55 kg.

Kouba lowering link will lower the rear suspension 1.75". Comes with bearings and seals installed for a quick and easy installation.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

Tractionator Dual Venture from MOTOZ. Based on the popular Tractionator Adventure and Tractionator RallZ front tires, but not directional!

• Off-Road performance with great on-road manners. ( 70% dirt / 30% street )
• Proven construction and compound for adventure and dual-sport use.
• Designed in Australia for dependable performance in a wide variety of conditions without the need to change tire pressure between off-road and on-road.
• Hybrid compound with Silica for optimum grip in mud, snow, and rain.
• Reversible for extended use.

NOTE: Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.

Dunlop designed the D606 tire to be street-legal but with an emphasis on aggressive off-road riding and great durability. A full-depth tread pattern designed for rigorous off-road use yields excellent traction on everything from hard-packed fire roads to soft single-track trails. At the same time, the D606's tread compound is engineered for good highway durability and grip.

The Dunlop D606 is R rated (max speed of 106 mph)

RallZ is the most aggressive off-road adventure tire in the Motoz range. Its DNA is part desert race tire and part long distance adventure tire. An ADV tire designed in Australia for adventure and rally use. Based on the popular Tractionator Adventure but with more aggressive off-road traction in all weather extremes.

DOT ECER75 approved.

NOTE: Tubes can be run in Tubeless (TL) tires, but a Tube Type (TT) tire cannot be run Tubeless.

Motoz Tractionator Desert H/T series of tires are renowned for great traction and long wear life. These tires are designed to handle hard terrain, fast and rocky trails as well as gravel roads and desert hard pack. Tricky off-cambers, ruts and hard braking at extreme lean angles are no problem for this DOT approved tire.

Note: Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.

This street-legal knobby from Pirelli has good stability and cornering precision thanks to the carcass stiffness. The tread pattern optimized for use on dirt and gravel roads, cross-country racing and desert tours. It has lasting off-road performance and knob tearing resistance due to the special off-road compound.

For straight 7/8" handlebar

Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Easy installation
• Tough and weather shielding Storm handguards
• Aluminum backbones are compatible with all Barkbusters deflector guards

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right Storm plastic handguard deflectors
• Installation instructions

Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.

Replacement handguards for your Cycra set up. Injection-molded high-impact plastic replacements. Includes all hardware needed for mounting.

Closed handguard with aluminum bar and bracelets.

Ultra-durable closed handguard designed for those seeking greater protection while competing or riding in enduro, hard-enduro and cross-country racing.

Equipped with a 35 mm "C" section anticorodal bar. Provides 5 times more resistance than the classic handguard with an aluminum bar.

The cuffs, oversized with a thickness of 19 mm, guarantee greater strength and increased torsional capacity.

Expanders made entirely of steel.

Cover is impact resistant; wide area protects the pilot's hands more, while flexible lower area absorbs any accidental contact with the knee.

Mounting kit included.  Mounts to all off-road competition bikes (motocross and enduro) with inner size from 13.5-16 mm and outer size from 22-28 mm.  Works with 7/8" or 1-1/8" bars.

Co-molded logo.

 Warp 9's CNC shark fin rear rotor protector. To make installation super-easy this fin bolts to a brand new CNC machined caliper bracket. Just remove your existing caliper bracket and remove the pins, install them on this new one and then put the caliper and fin back on.

Protect the underside of your TW!

• Made from 3/16' Aluminum.
• All Mounting Hardware Included

You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of a big tank? The 3.7 gallon tank from Clarke might be just right. It's almost 5 lbs lighter and holds close to 1/2 gallon more fuel than stock to increase your range by about 20 miles. Fits with your stock petcock, Pingel or Raptor petcock.

The new 4.1 gallon fuel tank from Clarke. Carries almost 2 more gallons than the stock tank. Available in Blue, Black, Silver, White or Natural

Get better range from your XR650L by adding a Clarke 4.7 gallon fuel tank. Cannot use stock shrouds.

Available in Natural, White, Black, and Red. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap, uses stock petcock.

Replacement Acerbis left-hand side fuel tank petcock.

For Acerbis tanks only.

Warp 9 stem puller

 Here is a list of the features of their CNC machined tool.

• Stainless Steel tip, wont break like softer brass tip
• Ribbed head for easier core removal
• Core tip threads into handle to protect tip from damage
• Includes spare valve core in handle for easy trail side repairs
• Tapered handle ends to make tip removal easier with gloved hands and non square edge doesn’t damage tool bags

Motion Pro T-6 Combo Lever has a hex box wrench for your axle nut on one side and a perfectly contoured tire spoon on the other. Manaufactured from lightweight forged T-6 aluminum with a hard anodized finish. These beauties are just under 10 inches long and weigh only 3.5 oz. Available in a 12/13 combo unit and a 22, 24, 27 and 32mm hex ends.

• Complete kit from Moose Racing to rebuild the OEM carburetor
• Each kit contains all necessary gaskets, O-rings, float valve and jets
• Supplied to Moose Racing by the same supplier the OEMs use

• Designed to fit in the factory air box exactly like original filter
• The best selling replacement air filter for competition motorcycles and ATVs
• Unique two stage design allows for easy and complete cleaning
• Dual layer of foam, can be serviced separately
• Thin Ultra Seal base is virtually impossible to tear and has a built-in "Grease Groove"

Designed for use with stock engines using either stock or aftermarket exhaust and air filters.

• Provides a simple and affordable solution to carburetor tuning problems
• Allows you to tune your bike for increased power and smoothness while retaining fuel economy
• Includes a guide booklet on how to install and use your jet kit to it's full potential

For mildly tuned machines using the stock airbox, with stock or K&N filter. May also be used with a good aftermarket exhaust system

• Provides a simple and affordable solution to carburetor tuning problems.
• Allows you to tune your bike for increased power and smoothness while retaining fuel economy.
• Includes a guide booklet on how to install and use your jet kit to it's full potential.
• For a top quality installation we recommend adding an extended fuel screw and a set of replacement carb screws.

Quality steel sprockets and 525 O-Ring chain. 525 chains come in 120 link length and will have to be cut down to fit. They also come with rivet type master links. Clip type master links are available below. Single sprockets and chains are also available below.

We have 44, 45, 46 and 47 tooth rear sprockets available for the SV. Select the sprocket size from the dropdown.

• Computer-designed to achieve ultimate strength at minimum weight
• JT combines leading-edge technology with top materials to produce the ultimate quality sprocket range with unbeatable value
• Every sprocket meets or exceeds the highest possible quality standards set for the motorcycle industry
• Sprockets are heat-treated and bead-blasted to reduce material surface tension
• Unless noted, rear sprockets made with top-quality-grade C45 high-carbon steel

Quality rear steel sprockets.

Rear Sprocket

Note: 2002 and later models have a 10mm sprocket bolts. 2000-2001 models have 8mm sprocket bolts.

For all years.

• Machined from impact and wear resistant chromoly steel
• Heat treated, then finished with a nickel coating for corrosion resistance

Quality steel front sprockets. Choose 525 or 520. Also available 'Wide Boss' JTF438 520 sprockets.

  All 520 sprockets require a new retainer plate, please add on if purchasing this size.

Quality steel front sprockets. Choose 13T through 15T. The stock size for the XRL is 15T. Go down in tooth count for faster acceleration.

A CNC machined chain guide for the DR. Stronger than the wimpy stock unit and can easily accommodate the stock 525 chain as well as a 46 tooth rear sprocket (by moving the lower rub block to the forward position). The rub blocks are also a higher grade, longer lasting material.

The chain slider protects the swingarm from contact with the chain. Replace yours before it wears through to the swingarm.

Always carry a spare master link when out on the trail.

  Master links are not interchangeable. Be sure to check the manufacturer and series on your chain.

These do not fit the TW200 or XT250. Only for 520 or 525 chains, Please verify chain size.

High Quality chain. Will need to be cut to fit your sprocket combination.

The stock sprocket retainer will rub the chain when it is used with 13 and 14 tooth sprockets.

CNC machined oil filler cap with locking clip to keep it in place in the roughest conditions. The cap is pre-drilled and the locking clip is safety wired to the mounting tap with a section of silicon tubing, that will not melt or discolor, over the wire. First class all the way. Available in Silver, Black, Blue or Red.

The starter bushing in the DR650 leads a tough life. Exhaust heat and minimal lube from the factory take their toll. Warp 9 has a high quality solution - a billet starter cover with a sealed ball bearing.

• CNC machined starter endcap
• Black anodized for good looks
• High Speed Abec 3 double sealed roller bearing installed
• Reduced amperage needed to start bike
• Brushes will have extended life

Warp 9 CNC billet machined Oil Filler Cap. 

Available in Blue or Black and it includes a new O-ring

To make removal as easy as possible, the center tab takes a 12mm wrench perfectly, or a 1/4" ratchet drive in the center. 

On each end of the center tab is a drilled hole should you find it necessary to safety wire your filler cap in place.
 

The idler gear is one of the few plastic components in the DR650 that can significantly impact engine performance if it fails or breaks.

This gear is crucial for driving the oil pump, which ensures proper oil circulation throughout the engine. In the absence of this component, complete engine failure may occur. While the idler gear is not frequently cited as a common failure point in the DR650 engine, failures have been reported, typically manifesting as either a fractured gear or stripped teeth.

During inspection, it is essential to check for any cracks, chipped areas, or missing teeth on the idler gear. Replacing the gear is a straightforward procedure, and it is advisable to do so while the clutch side case cover is already removed for other maintenance tasks, such as NSU screw replacements or clutch hub bushing replacements.

This component is a Genuine Suzuki part.

GoldPlug is the gold standard in engine protection.

Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.

10MM Thread

Got a little oil seepage or changing out your clutch pack? Here is the gasket you need for the right hand side case cover of your TW200. This is the same side of the engine as your kickstart lever and/or rear brake lever.

Can break or rivet chains from #35 to #530 like a pro.

kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.

kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.

NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.

ULTIMATE SPROCKET WRENCH KIT

• 12” long wrench gives you more torque to get those thread locked sprocket bolts off easily
• Double ended 12mm & 13mm to fit all modern motocross, Enduro and dual sport bikes
• Dog leg wrench design allows wrench to easily clear rim edge and wide tires
• 8mm allen fits most Japanese bikes 8” long for extra leverage
• Torx T45 fits late model KTM and Husqvarna bikes, 8” long for extra leverage
• Vinyl coated handles to protect rim edge and give a non slip grip
• Makes routine sprocket bolt maintenance a quick and easy job

Designed to enhance the appearance of your TW200, yet provide greater riding distance per tankful. This larger fuel tank has double the capacity of the stock tank at 3.6 Gallons, yet very slim and sleek. This tank has a custom design that will allow the use of OEM & Maier side covers. These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.

Comes with New Screw Cap.

Requires OEM/Stock petcock and oval rubber grommets for install.

If you do not have the grommets or if your O.E. grommets are in poor condition you can add these to your tank order.

Handlebar mounts that replace your stock clamps.

These raise your handlebars 1 inch.

Choose 7/8" for standard handlebars or 1-1/8" to allow installation of your choice of oversize/ tapered handlebars.

CNC machined from 6061 Aluminum by the crew at Warp 9. This upper triple clamp will help to get the bars out of your lap on the XR650L. It allows for six different bar positions (three mount positions and reversible offset mounts). Uses the stock key switch and works with the handlebar lock. Speedometer and indicators all use mounting positions as well.

This clamp comes with 1-1/8" handlebar mounts.

The Warp 9 shift lever is black anodized and the Warp 9 logo is laser etched into the finish. Comes with a black anodized knurled aluminum tip that folds and returns via a stainless-steel return spring. Includes the pinch bolt as well.

The Warp 9 shift lever is black anodized and the Warp 9 logo is laser etched into the finish. The black anodized knurled aluminum tip is folding and returns via a stainless-steel return spring. Includes the pinch bolt as well.

The tip is replaceable in the event of damage.

Warp 9 has created a beautiful brake pedal machined from billet aluminum to an 8mm thick work of art. A stainless steel pin eliminates wear in the frame. This pedal has the ability to move the spring loaded brake tip 10mm either way from the center position. The arm is arched to provide clearance for riders who have the lowpeg + centerstand combination.

The Warp 9 shift lever is 7075T6 CNC arm, the Warp 9 logo is laser etched into the finish. 

Includes a black folding aluminum tip and stainless spring and pivot pin for years of rust free use.

1" longer than stock

• Warp 9 Flex Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces
• Adjustable reach allows customization to the rider’s hand size
• Double hinge design allows lever to flex out of the way in most impact situations
• Pushrod or Bearing contact styles for smooth brake modulation
• Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal

Fit Disc Brake Models Only

Warp 9 Flex Brake Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces.

Adjustable reach allows customization to the rider’s hand size.

Double hinge design allows lever to flex out of the way in most impact situations.

Pushrod or Bearing contact styles for smooth brake modulation.

Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal.

The Warp 9 "3-Finger" Lever Exclusive to ProCycle.  You asked for 3-finger levers, and we had Warp 9 make them for us. Brake lever includes a nice billet clamp with nylon sleeve to allow the assembly to rotate on impact. Will not fit with the stock OEM wind deflectors.

• Warp 9 Flex Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces
• Adjustable reach allows customization to the rider's hand size
• Double hinge design allows lever to flex out of the way in most impact situations
• Pushrod or Bearing contact styles for smooth brake modulation
• Titanium Pivot / Black levers with laser-etched Warp 9 logo

Will not engage the clutch switch on 2010 and later models

Warp 9 Flex 3-Finger Levers are machined Billet, anodized and hinged levers with CNC machined master cylinder interfaces.

Adjustable reach allows customization to the rider's hand size.

Double hinge design allows lever to flex out of the way in most impact situations.

Pushrod or Bearing contact styles for smooth modulation.

OEM Style aftermarket replacement brake and clutch levers. Standard length. 

Available as a set or individual.

Please notice that this set is for '90-'09 DR650.

Say goodbye to the frustration of fidgety handguard expansion plugs with Warp 9's innovative Tapped Handlebars. 

These handlebars feature ends that are plugged and tapped with an M8x1.25 threaded insert, providing a secure and reliable mounting point for all aftermarket wrap-around handguards. 

No more worrying about plugs pulling out or spinning during crashes; their robust design ensures you're good to go, even when you encounter obstacles. 

Not using handguards? No problem they've got you covered!Each set of handlebars comes with aluminum grip guards and stainless bolts, offering protection for your grips and delicate throttle tube in case of a get-off. 

Designed with an oversized 1-1/8 inch (28.6mm) clamping diameter that tapers down to 7/8 inch (22.2mm) to accommodate standard controls. Crafted from 7010 T6 aluminum tubing and featuring computer-extruded variable wall thickness, they effectively reduce vibration while enhancing overall performance and comfort. 

Note: Does not include pictured bar mounts.

Upgrade your Honda XR650L with a Subframe Brace Kit, designed to enhance strength and rigidity for your bike. This complete kit connects the frame and subframe, reinforcing the structure to support increased load capacity—perfect for riders using side cases, top cases, and rear racks.

Key Features:

• High-Quality Materials: Attachment points are machined from 6061-T6 billet aluminum for superior strength and durability.. The 6.5mm thick support bars are laser-cut for a perfect fit.

• Easy Installation: No cutting, drilling, welding, or modifications required for installation. Easy 20 min installation.

• Enhanced Load Capacity: Provides added rigidity and support to the subframe, improving bike stability when carrying additional gear.

• Exhaust Compatibility: Compatible with both STOCK Exhaust and FMF Exhaust systems.

New from Warp 9, top of the line Adventure Pegs. a full 5" long and 2.5" wide will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a single track trail.

• Ceracote coated Chromoly steel pivot for the ultimate in strength
• Replaceable 7075 T6 Aluminum Platform
• Permanent Stainless Teeth provide the ultimate in non-slip traction
• Built-in bottle opener in the bottom!

  NOTE: These pegs DO NOT fit the '18 model!

New from Warp 9, top of the line Adventure Pegs. a full 5" long and 2.5" wide will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a singletrack trail.

• Ceracote coated Chromoly steel pivot for the ultimate in strength
• Replaceable 7075 T6 Aluminum Platform
• Permanent Stainless Teeth provide the ultimate in non-slip traction
• Built-in bottle opener in the bottom!

Fastway offers a large ADV peg that is 4.75" long and 2.25" wide. With these pegs you can adjust the camber with their patented FKMS Kamber bolt. ´Tilt´ your pegs to increase comfort, or to give better squeeze on your bike. These pegs come with two sets of F3 cleats (one standard, one long). You can order serrated or spiked cleats separately.

These Adventure pegs are offered in several colors, but some colors may require extra time, call for availability.

The indestructible, yet lightweight steel tube construction offers the best angle and ground clearance, makes it easy to jack up and provides stability - whether it's during maintenance or on the road. In most cases, you will no longer need to buy an additional swing arm stand. During long downtimes in the winter months, the centerstand helps take the load off your tires.

• Stands securely when traveling with lots of luggage and during maintenance
• Bike-specific design for easy mounting and high cornering clearance
• Easy to lift up the motorcycle
• Outrigger for optimal leverage
• Best corrosion resistance due to sand blasting and powder coating of the surface
• Made of robust steel
• Total Weight: appr. 1,6 kg / appr. 3.6 lb

The FMF Powerbomb is a four stroke header pipe unit that has a unique bulge precisely located in the header system. A "pre-muffler" of sorts, the Power Bomb actually lowers sound output because it creates more surface area to absorb the sound medium (exhaust). The surface area of the perforated core lets the sound exit into the absorbing material (steel wool packing) and then allows the air to expand, cool and ramp back up with the higher pressure air. The result? The FMF Powerbomb is instrumental in reducing the decibel level on any four stroke and because of the expansion and contraction on exhaust through the system, the flow has been increased by nearly 10%. That means more power throughout the range.

Features:

• Tuned for bottom to mid performance
• Powerbomb headers are the front runner in performance headers
• Designed for full service access to oil filter

Did you snap a headpipe bolt on your XRL or are your headpipe bolts looking a bit dingy and rusty?

These replacement header exhaust stud bolts are made of super corrosion resistant 316 stainless steel.  They provide excellent resistance to chemicals and saltwater to give your exhaust system a hassle free service life.  

If you've got an older XR650L, you know the struggle of removing the O.E. nuts from the studs.  They either snap, remove the stud or come off as they should.  At some point you're likely to snap on or come across a seized nut to stud.  These bolts are a superior upgrade to the O.E. nut and stud.

Kit includes: 4 Stainless Steel bolts

The new DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 89db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.

You may want to consider a new exhaust gasket that goes between the header and the muffler.

This is the gasket used between the header pipe and the stock muffler. This gasket is not needed for aftermarket mufflers!

The plastic fitting that secures the stock choke cable to the carburetor is delicate and easily broken. A broken fitting can cause hard to solve idling and running problems.

CNC machined from billet aluminum and anodized black or blue. If you want to retain your handlebar mounted choke this may be the solution.

  These no longer fit the new version of the ProCycle Remote Choke Cable. Will not work with the long or short reach choke knobs.

• Stop your expensive helmet from falling and hitting the ground while you’re out riding
• The perfect solution to easily store your helmet with your bike.
• 7075 T6 machined aluminum
• Fits all 7/8 handle bars
• Includes 2 stainless screws
• Fits virtually all bikes and makes ( except Harley )

• Warp 9 Flex Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces
• Adjustable reach allows customization to the rider’s hand size
• Double hinge design allows lever to flex out of the way in most impact situations
• Pushrod or Bearing contact styles for smooth brake modulation
• Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal

The Front Rack gives a lot of options for functionality.

CycleRacks are made out of Schedule 40 11/16 black steel pipe, bent in a press, and welded together in a jig.

All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.

Ready to go tool kits. Just toss it in your bag and hit the road... or the trail.

No longer need your speedo drive? Install an electronic unit? This CNC machined aluminum unit will replace the stock speedo drive on the front wheel keeping things properly spaced and sealed up.

To suit a 20mm Axle.
Before placing your order please ensure you check the diameter of the axle, as the earlier models may have different sized axles.

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.

Complete seats are built by Seat Concepts on a new seat pan and come ready to be installed on your bike.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand.

Includes pads for both front and rear.

Small Wheel models have a 17" Front Wheel and 14" Rear Wheel.

Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability. These Aramid fibers have a high strength-to-weight, thermal stability and abrasion resistance to provide advantages over steel fiber-based products. They provide excellent stopping power without noise and rotor galling but still provide fingertip control and strong, predictable brake response.

Double-H sintered metal brake pads feature the HH friction rating, the highest in the industry. These pads provide maximum brake effect and last twice as long as organic pads.

Semi-sintered pads have an all new recipe containing 30% copper by weight with an organic matrix. This design combines the long life of a sintered pad with the great feel and lack of rotor damage common with full-sintered pads. These can be used to replace Kevlar or sintered metal compound pads.

Set includes pads for both front calipers.

Quick release one-piece clamps that saves space. These are great for fuel lines, controlling wires, and can be used many times.

Comes with 4 each of 8mm, 9mm 10mm, and 12mm.

No special tools needed, from Helix Racing.

A pack of 10 Fuji style lock nuts to put on the sprocket of your KLR650. These are an 8 mm, flanged type nut that will keep your sprocket snug and tight.

ProCycle Rev Box increases the rev limit to 10,000 RPM. In addition, this unit offers a re-mapped timing curve which yields a noticeable increase to horsepower and torque over the stock CDI

This CDI box is a direct plug in replacement CDI. Simply locate and remove the stock CDI, and plug the unit directly into the wiring harness, no modification needed. Suitable for stock and modified machines

Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.

Thin wall bi-hex sockets designed to access narrow spark plug holes.

• Use with 3/8" drive ratchet or wrench
• Choose the one that fits your spark plug size:  14mm, 16mm, 18mm, or 21mm.