Search Products

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

A premium billet sprocket carrier from Warp 9 Racing that houses 2 bearings to help protect against the sideways twisting load that is commonly known to prematurely wear out the bearing and cush rubbers. This wear can cause extreme failure possibly damaging the hub.

Offered in anodized Silver or Black, Includes spacers and hardware.

These are designed to work with Warp 9 and OEM hubs.

Choose 17" Supermoto, 19" Adventure or stock 21" front wheel. All work with the stock DR650 speedometer and cable on either the stock or Warp 9 hub.

These top of the line Adventure pegs from Warp 9 are 5" long and 2.5" wide. They will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a singletrack trail.

• Ceracote coated Chromoly steel pivot for the ultimate in strength
• Replaceable 7075 T6 Aluminum Platform
• Permanent Stainless Teeth provide the ultimate in non-slip traction
• Built-in bottle opener in the bottom!

• Wider, lighter, stronger design. Platform is 60mm wide x 100mm long, overall approx length from center of footpeg pin to end of peg is 115mm
• Widest (mm) and lightest pivoting pegs on the market
• Upgraded heavy duty, long life springs
• Unique multi-directional grip pattern
• Outstanding build quality
• Overhaul kit includes: 2 pivot bushings, 2 pivot tension springs, 2 lock nuts, 2 washers, 6 o-rings, 2 split pins and instructions

2 high-quality bushings per set. They recommend changing bushings every 40 hours or at least once a year to get the best performance out of a set. If you are on an Adventure Bike and are doing a lot of road miles they recommend swapping out bushings once a year to ensure that you get the most vibration dampening of the bushings.

Every new set of pegs comes with a 90A bushing installed. This is a medium flex rating. 
80A is the softest and 95A lock-out is the stiffest and has the least amount of flex.

The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference. 

The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.  

For use on Motion Factory Foot Pegs Only

Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm.

Our complete foot peg assemblies. 1-3/4" lower than stock. No extra brackets that hang down below the frame. Easier on the knees. Wider platform Yamaha YZ style footpegs are stronger and give you firmer footing. Mount solid to the frame. No more 'droopy' feeling when standing on the stock pegs. Lowering your footpegs makes it easier to stand and less of a reach down to the bars when standing.

Now you can get our Low Pegs with MK4 Pivot Pegz or black Fastway ADV pegs (both Yamaha YZ pegs) installed!

 Warp 9's CNC shark fin rear rotor protector. To make installation super-easy this fin bolts to a brand new CNC machined caliper bracket. Just remove your existing caliper bracket and remove the pins, install them on this new one and then put the caliper and fin back on.

Protect your brake rotor and fork lowers from mud and debris. Choose between black or white.

High quality aluminum caliper guards from Works Connection protects your brake caliper and looks great too.

Protect that vulnerable rear master cylinder with this thick aluminum guard from JNS Engineering. CNC laser cut then formed and given a clean black powder coat finish. Includes new button head screws and aluminum spacers.

Fits Moose and other aluminum hand guards

• Aerodynamic and stylish design
• Protect hands from brush, water and cold wind
• Simple installation
• Sold in pairs

For Straight 7/8" handlebar

Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.

Note: This kit includes the handguards only. Deflectors sold separate, can be added by selecting color from drop down menu.

For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.) 

To be fitted to the top of the Barkbuster EGO handguard.

• Easy installation.
• Can be removed in minutes for a more compact feel.
• Deflectors provide maximum protection and coverage from the elements.
• Deflector Set available in black or white to suit your style.
• Includes two deflectors and mounting screws.

For straight 7/8" handlebar

Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Easy installation
• Tough and weather shielding Storm handguards
• Aluminum backbones are compatible with all Barkbusters deflector guards

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right Storm plastic handguard deflectors
• Installation instructions

Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.

Maximize your wind protection with Barkbusters' largest handguard plastic! For use with single sided Storm mount and all Barkbusters backbone handguards

For Tapered 1 1/8" Handlebar

Protect your hands and levers with the Barkbusters Storm lever and weather protection handguards. Full wrap solid heat treated aluminum bars with secure two point mounts on each side provide strength while attractive and generous guards provide shelter from the wind and weather. Ride longer with the Storm handguards and complete mounting kit by Barkbusters.

Features:

• Two mounting points provide secure protection
• Full wrap guards
• Heat treated aluminum backbone bars
• Easy installation
• Tough and weather shielding Storm handguards
• Aluminum backbones are compatible with all Barkbusters deflector guards

What's in the box:

• Left and right aluminum backbone bars
• Inner and outer handlebar mounting hardware for both sides
• Left and right Storm plastic handguard deflectors
• Installation instructions

Not recommended for Africa Twin, T7, Himalayan, or V-Strom. Please see specific listings for those models.

NOTE: tapered kit will not fit Renthal Twin Wall or Barkbusters VSBar

This is the ultimate radiator guard for the CRF250L. Protects your  radiator from both front and side impacts.

A rear mounting bracket provides that extra support. Constructed from 1/8" aluminum, the kit includes all necessary mounting hardware for a very simple installation.

Givi makes a great set of Crash Bars available for the Africa Twin. If your intentions include off-road riding of any kind, you really should not go without protection. Not only for you, but for your bike too. Even a slow-speed tip-over can cause damage that would make riding away impossible.

For the upper set, you just need to select the matching color to the lowers you have ordered. Install them all at once, or the lowers alone for a while, then the uppers. You cannot order the uppers without the lowers though as they will no mount correctly. The upper crash bars protect important radiators and bodywork. Essential in the event of any kind of crash. These also make excellent mounts for auxiliary lights for added visibility.

Included with each piece you receive a complete set of instructions and all mounting hardware required, in typical Givi fashion.

NOTE: The upper units REQUIRE the lower crash guards for proper mounting and are not a stand alone item!

Please Note that these Crash Bars are also compatible with the Givi Skid Plate.

These grips feature a thicker design that dampens vibration. The soft shoulder allows ease of movement. Three wire-tie grooves are molded into the grip to make securing them a breeze. We think they are great!

This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 2008-2018 Yamaha XT250. The new design for the black headlight produces more light and has much more uniform beam pattern when compared to the previous version. New design currently only available in black, chrome may be available in the near future. No wiring, soldering, resistors, trimming, drilling, or fabrication required.

• Low Beam: 20W, 3,600 Lumens
• High Beam: 40W, 4,500 Lumens
• Color Temperature: 6,500k
• CREE LED Chips
• DOT & SAE Approved
• CE, RoHS, ISO9002, IP67

A portable device that can jump-start your motorcycle or car. It can also charge your cell phone, GPS unit, laptop or other electronic devices via USB cable.

• XP-1 is 6" x 2 7/8" x1" 14oz.
• XP-3 is 5" x 2 7/8" x 1" 12oz.
• Holds a charge for up to 1 year.

Planning a motorcycle trip can be hard work. Butler G1 Maps highlight the best paved motorcycle rides in the country so you don’t have to guess which roads are good. Their dedicated team rides and rates every road you see on the water-proof maps, hundreds of thousands of miles so far. Their easy to read rating system clearly indicates the most dramatic and scenic stretches and are accompanied by detailed inset boxes, written descriptions, elevation profiles and whole bunch of useful information to help you plan your journey.

If you already have a Quad Lock Case, you can Twist Lock and Go with any of these secure mounts.

Or Choose the Universal Adaptor to use your current phone case.

If you already have a Quad Lock Case, or Universal Adapter and Mount you can add these accessories to Twist Lock and Go on another level.

Stock gearing uses a 45 tooth rear sprocket

The 50 tooth rear sprocket will give you much lower gearing for off-road use. You will need a longer chain for this rear sprocket, please order the 130 link chain to fit with this larger sprocket, it may need to be shortened to fit correctly.

All of these options are for complete systems, including head pipe and muffler. The S option is for a Silencer only while the S/A is for a system with a Spark Arrestor.

The latest version of the Powercore 4 design incorporates a hi-flow core which mas more surface area to absorb more sound while flowing more exhaust. The silencer is constructed with an extruded aluminum canister is MIG/TIG welded and has space age internal packing. This system is lighter, stronger and provides more power than stock exhausts. The pipe is a stainless steel unit for strength and weight savings.

Powercore 4 S/A has a US Foresty approved, maintenance free, stainless steel spark arrestor screen to be sure you are safe and legal in the woods.

These gaskets seal the joint between the head pipe and muffler. They are easily damaged when removing the original muffler. Get a fresh pair now to ease installation of your new performance muffler. Sold as a set of 2.

This gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers do not require a joint gasket but the all other aftermarket mufflers as well as the stock muffler require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.

Set your bike apart with a custom exhaust look. Withstands direct heat up to 2000°F.

• 2 inches wide and 25 feet long
• Available in black or natural
• 4 stainless steel tie wraps

The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.

• Uses long-life muffler packing for increased packing life
• Forest Service approved spark arrester

Designed to enhance overall performance when installing a high-flow jet kit. This CDI box enhancements include:

• Altered ignition advance curves
• Wire lead for a tachometer

This unit may also be used to replace a defective CDI box on a stock machine. 

Please note that the internal circuitry of Rick's CDI unit necessitates the engagement of the clutch or kickstand neutral safety switch for proper operation. Specifically, the clutch must be engaged (pulled in) when the kickstand is in the down position. This requirement may not be present in the original Yamaha OEM CDI unit.

Antigravity Batteries introduce the ground-breaking "RE-START (RS)" line of batteries. These are the first batteries with built-in jump starting! They intelligently monitor their status, and just before going completely dead, puts itself to sleep with just enough energy to get your vehicle started again. Simply press the RE-START button located on the battery, then start your bike and ride away!

These are an extremely lightweight (2.3 lbs.) and high-powered Lithium-Ion replacement battery for motorcycles. These batteries offer the first Battery Management System (BMS) found on a powersport battery and includes low-voltage cut-off, over discharge, over-charge, and thermal protections with real time lithium-ion cell balancing. Highly recommend using a lithium charger to maintain the life of the battery.

3 Year warranty

Product Size is just 5.9"L x 3.5"W x 3.74"H. If you need spacers, select the optional Foam Kit to pad the battery in the battery box.

Sold individually.

The Adventure Kit is perfect for adventure and touring bikes where the mirrors are kept up most of the time. This mirror offers the widest field of view, and is ideal for riding paved and dirt roads.  The 6 inch arm is a little longer than anything else on the market, for great visibility on loaded bikes.

• Made from super tough glass reinforced zytel
• Reflector Dimensions: 5.25" x 3.5" (135mm x 95mm) 
• Overall mirror length: 7" (175mm) (not including arm mount)
• Convex lens meets SAE and CE specifications 
• Mirror mounts to any 10mm perch.

The new Doubletake ball is oversized, and high quality nitrile rubber surrounds an aluminum base that won't degrade under extended compression. 

The Doubletake Base Kit includes bolts to thread into every application (even reverse thread Yamaha's), without adapters. 

The Trail Mirror is a simple solution for any dirtbike or mountain bike. Gives you hindsight when you need it, but you forget it's there otherwise. 

• Made from super tough glass reinforced Zytel
• Reflector diameter: 2" (50mm)
• Bar space: 0.75" (19mm), Height 1.25" (32mm)
• Convex lens for wider field of view

Zip ties directly to the bar- no hardware required.

Sold individually

Replacement shift lever from IMS with folding tip.

A set of replacement brake and clutch levers. Standard length.

A stock replacement brake pedal for the DR650. Nothing fancy but sure gets the job done. Just order it up and get back on the trail. See our Brake Pedal Adjuster Bracket that allows you to adjust the position of your brake pedal to perfection.

• Tool-less cable adjuster
• Machined billet aluminum with a durable anodized finish
• M8 x 1.25 thread

• Lightweight levers are CNC-machined from aluminum
• Stock length; reach to the lever is adjustable to six positions

Sold Individually

A quality replacement speedometer cable from Motion Pro.

• Black vinyl coil-wound housing
• Meets or exceeds OEM quality
• Inner nylon sleeve for longer life and smooth operation

A quality set of replacement throttle cables from Motion Pro

High-performance, high-flow filter element and filter base for the TT-R 125.

• Replaces stock filter and base
• Filter base is made from HDPE plastic
• 3 times larger than stock filter!
• Adds almost 1/2 horsepower
• Designed to fit inside the factory air box

• Manufactured to perfectly fit the factory airbox, these filters use top-quality materials from around the world including the Powerflow filtering media
• Direct replacement of original equipment filter with no need to change carburetor jets or settings
• Designed and developed to meet the demands of high-performance engines

Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air- the number 1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow

Unsurpassed in airflow, dirt stopping and overall performance. Adding a pre-filter to your intake system gives you extra protection from damaging contaminants.

Is the cylinder head intake boot on your DR650 cracked or weathered, is it missing parts of the lip to seal around the carburetor, have you recently pulled the intake boot off only to realize the O-ring behind it is hard & brittle? This kit is your solution to solving some of those mystery problems and make your bike like new again. There can be a great deal of heat that can radiate behind the cylinder head on a DR650 as it is an air cooled engine. With that comes long term maintenance items that will need to be replaced due to them being made of materials that cannot withstand those constant heat cycles indefinitely.

Our kit includes O.E. parts from Suzuki to include:

1. Intake Boot
2. Metal Clamp
3. Premium Japanese O-ring

Has your TM40 carburetor been sitting for too long and now needs to be rebuilt? Then what you need is this TM40 Rebuild Kit that contains Genuine Mikuni replacement parts.

This kit includes:

• Needle Clip and Washer
• Top Cover Gasket
• A/P Nozzle O-Ring, Plug and Rubber Cap
• Fuel Screw O-Ring, Washer and Spring
• Float Bowl O-Ring
• Pilot Fuel Screw
• Drain Plug O-Ring
• #3.8 Needle Valve Assembly
• O-Ring for the Starter Circuit and Needle Valve
• New Screws for the Float Bowl
• Vent Hose

Kit includes:

• Main jets: 145, 150, 155 and 160
• Pilot jets: 38, 40 and 42
• Merge Racing AP spring
• JD Fuel screw
• #35 leak jet
• EMP and EMR needles

Everything you need to dial in your FCR/DR650 conversion. Enough jetting to cover most modifications or altitudes.

Not for the stock carburetor Fits FCR-MX conversions Only

A CNC machined fork brace to stiffen up the notoriously wimpy front end on the DR. Have more confidence in your front end on or off the pavement.

Split design means that installation takes minutes without having to remove the forks. Available in a black anodized finish.

Lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.

Stock spring rate 0.60 kg/mm

Race Tech Recommends 5w oil, 2 qts to reach 110 mm oil level.

In stock form, the forks, featuring a single spring design are under sprung for any rider over 100 pounds. With limited travel, adding a stiffer spring in the right leg only per the stock design was not a viable option.

Race Tech instead offers a High Performance Spring Kit that adds a stiffer spring to the other fork. (The overall spring rate in the forks is the average spring rate between both legs.) This upgrade will make a drastic improvement in handling for most riders.

0.50KG/MM KIT

Included in this kit are .42 kg/mm fork springs, Cogent DDC (Drop in Damper Cartridge) performance cartridges and two bottles of 5w fork oil.

Developed by the KLR suspenison experts at Cogent, this set of springs will stiffen up that wimpy KLR front end. Choose between .64 kg/mm springs (60% stiffer than stock) or .70 kg/mm units (75% stiffer than stock).

These springs are custom wound specifically for the XT225. Stiffer than the .36 kg/mm stock springs, these will make your front perform significantly better. Combine them with the Cogent DDC's and you will be very happy with the results. Sold as pairs.

• Race Tech's original bolt-on fork valving system for front cartridge forks
• Triple the flow area of stock pistons
• Put valving control on the shim stack
• Outstanding tunability; improved control, traction, plushness and bottoming resistance
• Complete instructions, Gold Valve pistons, valving charts, valving shims and "Technical Edge
• Fork Maintenance and Gold Valve Installation" video all included

These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. No disassembly of your forks, no drilling of damper rods. Just change the oil to 5w and install the DDCs under the springs and hit the trails.

Stiffer fork springs are required to realize the full benefits of the DDCs. .42 kg/mm springs are the springs recommended for just about anybody out there. Please call if you have any further questions.

The DDCs are not recommended for use with progressive springs.

The DDC Install/Removal Tool which makes installation that much easier.

• Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life
• Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material
• Triple-lip seal design
• Dyno-tested to last 3 to 4 times longer than OEM seals
• Directional ribs allow seal to be installed easily
• Sold in Pairs

• Kit includes a pair of oil seals and dust seals; no bushings or other rebuild parts included
• Seals have been tested to over 1 million strokes in R&D development
• Every part meets or exceeds OEM quality standards
  
   

Lowers the rear suspension. Precision machined from billet aluminum and anodized.

*Important when lowering the rear suspension you want to raise the fork tubes in the clamps an equal amount of inches that the rear is being lowered. That way your bike will sit level when done.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

The Pro-Series is an excellent replacement for the stock shock. With both compression and rebound adjustable as well as preload adjustable, you can tailor the performance to match your riding style. Compact and rigid design with piggyback type reservoir specifically engineered for your WR250R. Fully serviceable shock is designed for the long haul.

Select the spring you want installed based on the load you plan to carry. Choose the 'standard' 8.15kg/mm spring for rider/ luggage up to 220lbs. Weigh more than 220 lbs, or are loaded to the max, think about the 10.19kg/mm 'heavy' spring.

Stock suspension suffers from poor compression damping and limp rebound damping. The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.

• Bolt-on shock valving for serious suspension performance
• Improves control, traction, plushness and bottoming resistance
• Improved, long-wearing, low-friction sealing design decreases fade
• Includes complete instructions

This CNC cap will replace the stock gas cap on the stock tank. You do need some parts from the stock cap, so don't throw it away yet! It is not difficult and this kit includes the additional hardware required. Also included is a vent tube with a matching cap.

For use on STOCK TANK ONLY! This is NOT a locking cap.
Does not fit California model DR650

You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of the big Acerbis or Clarke tank? The 4.0 gallon tank from IMS might be just right. Includes cap, uses stock petcock.

You’d be amazed at the dirt and debris that can work its way into your gas can – and from there, your fuel tank. Twin Air’s monofilament screen pocket inserts in your tank to catch particles as small as 40 microns (.00165”) while allowing the gas to flow freely. 

The flange is custom-sized for each modern 4-stroke model to ensure a leak-proof seal. Just remove the filter periodically, turn it inside-out, and clean out the debris that could have been in your engine.

Will not work with factory locking gas caps.

Includes all necessary o-rings and diaphragms

The Complete Doohickey Replacement Kit features the Doohickey supplied by Eagle Manufacturing, a torsion spring accompanied by a drill bit, a generator cover gasket, and an exterior cover gasket. Additionally, it includes all necessary components for rotor removal, along with a replacement bolt for reassembly.

The PSR Oil Filler Caps are CNC machined from high quality aluminum and come with an E-clip that is already safety wired to a mounting tab. The wire is covered with silicone tubing that will not melt or discolor. Available in silver, black and gun metal.

Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

You pay $3.59 per filter with our value 5-pack!

Providing unbeatable performance and exceptional value, Hi-Flo Filter is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

Grab our 5-pack and save both time and money!

This is an extended version of the stock DR650 clutch release arm that is manufactured by Suzuki.

Upgrading to a longer clutch release arm will lighten the pull of the clutch lever through means of increased leverage. This means less fatigue, quicker clutch engagement, easier clutch modulation and longer rides.

The extended clutch arm will not offer a drastic change in clutch pull. If you're looking for a major change in clutch pull at the lever, we recommend getting a Magura hydraulic clutch kit.

Stock and typical after market drain plugs can protrude past some skid plates. This steel low profile drain plug stays inside the skid plate so it can't be snagged by passing objects.

Comes with 4 crush washers.

Features:

• Clips on to brim of hat for hands free use
• Adjustable head for precise illumination
• Wide angle LEDs provide a flood of light
• Internal rechargeable li-ion battery (micro USB charging cord included)
• High and low settings, up to 4 hour runtime

• Each kit contains all necessary components to rebuild a master cylinder
• Made by Nissin, an OEM supplier in Japan

Repair kit for your rear disc brake master cylinder.

This kit includes a 320mm Wave rotor, caliper relocation bracket and new Galfer semi-metallic brake pads.

You can add a Stainless Steel brake line, and DOT4 fluid to your package.

For the frame drain on your XR650L ,extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!

The Chilly Exhaust Heat Shield is the most effective heat shield on the market. The innovative three piece design consists of a top shield attached to 2 rails with rivets and spacers. This reduces the contact area and slows down heat transfer. They have incorporated a patented, insulated reflective blanket on the underside of the shield to reduce radiant heat transfer. The included stainless steel clamp makes it simple to install.

We highly recommend a heat shield if you run soft luggage without hard racks.

FEATURES:

• Solid Top Shield - The logo is laser etched and there are no cutouts on the top shield. This prevents radiant heat from passing straight through to your luggage.
• Side Rails - By isolating these with spacers the heat conductive surface area to the top shield is reduced and slows down heat transfer.
• Radiant Heat Shielding - The reflective insulated blanket on the bottom of the shield is the real hero. This patented material won't be found anywhere else in the motorcycle industry. 
• Stainless Steel Clamp - Slots have been provided in the side rails to make installing as easy as it gets.
• Brushed Aluminum - Lightweight and looks nice.

DIMENSIONS:

• Length 7.5" (190mm) x Width 3.5" (76mm) x Height 1" (25mm)
• Clamp fits any exhaust 3.5" - 5.5" (89mm - 149mm)

Includes new Suzuki side panels, heat shield, headlight cover, rear fender and your choice of aftermarket off-road or supermoto front fender.

Choice of off-road or supermoto (SM) front fender.

Blue kits come with white side panels.

Quality windscreen made from Lucite aircraft acrylic making it more rigid and optically clearer than OEM windscreens

These models are 2"-4" shorter or 2"-4" taller than stock to meet your particular riding preference.

Rear Fender comes with built in tabs designed to be used with Maier USA Side Panels.

• All Maier bodywork is made of tough, vacuum-formed high-gloss polypropylene
• Drilling is required
• Colors are OE color matched

Quality replacement rear fender from Maier.

Quality MX style rear fender from Maier.

Quality replacement headlight fairing for Gen 1 KLR650.

Available in 4 colors.

PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash. 

Sold as a pair.  Easy to Install

• Complete with all necessary mounting hardware
• Fabricated with 1/2 inch steel tubing, MIG welded
• Finished with a semi gloss black industrial grade powder coat
• Comes with left and right side racks, each side weighs 2 lbs

Precision Motorcycle Racks strongly recommends these side racks be used with their Top Rack because the racks use each other to mount properly. They were never intended to be used by themselves without the rear rack. 
If you are going to mount these side racks without the use of their top rack please select the extra hardware kit option that includes 2 brackets, 2 steel spacers, and an extra hardware kit that is required for proper installation.

These side racks will not play nice with any other brand rear rack, and installation without their top rack will prove to be quite difficult.

The B&B Off Road Engineering rear carry rack is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible. Our carry racks are Tig welded with a polished finish and are sturdy enough to use as a grab handle.

DIMENSIONS

Width Flat Surface Approx 18cm

Length Approx 33cm – Total Length Approx 45cm

Please Note- To fit rack, two holes need to be drilled into the rear guard. The position of holes are already marked on genuine Yamaha guard so no template is required.

These are high-quality straps made by Givi. They have a nylon belt with an anti-slip metal safety buckle. The long strap is 67" long by 1" wide with a 100 kg maximum traction load. The short straps are 39" long by 3/4" wide with a 75 kg maximum traction load.

There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.

You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.

• Plug and Play
• 7 Different Programmable Turn Signal Patterns 
• Safety Brake pulsing built in (Can Enable or Disable)
• Superbright LED's; For excellent brightness, even in direct sunlight
• License Plate Light built in
• License Plate Bracket fits the common USA license plates, sloted for maximum plate compatibility.
• Includes Mounting Hardware
• Saves about 2 lbs over the factory tail light setup
• Made In the USA

We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.

This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.

This kit includes a DOT LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.

How does this headlight compare to our original TW200 kit? First and foremost, this kit has SAE/DOT markings and a much wider/brighter high beam pattern. The low beam is very similar to our original kit: wide, flat, and bright but with more punch. The DOT headlight assembly has also proven to be more durable than the original headlight.

Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Approved
CE, RoHS, ISO9002, IP67

No cutting, drilling, or wiring modifications! Installation takes 5 minutes.

Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.

  Please note that this product is not compatible with the 1987 TW200.

This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.

  Not compatible with any DRZ400

Use this tool to check for air leaks in two-stroke engines. It includes air pressure gauge, pump-up bulb and most fittings and adapters for single and twin-cylinder two-stroke motorcycle engines. Packed in a convenient carrying case with instructions.

Made from precision-drawn, chrome-vanadium tool steel, the BikeMaster® 9-Piece Ball End Hex Wrench Set and Holder features a bead-blasted surface for a better grip and a corrosion-resistant coating. They have a ball end, allowing an angled reach and access to obscured bolts. It comes with a durable holder and manufacturer's lifetime warranty.

Comes with sizes 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm and 10mm

• Interchangeable tips to fit 8 sizes of spoke nipples.
• ( 5.6 / 5.8 / 6.0 / 6.2 / 6.4 / 6.6 / 6.8 / 7.0 mm )
• Main shaft is CNC precision machined from 7075A aluminum and designed for optimum grip.
• Tips are made of heat treated steel for strength.

The genuine factory shop service and repair manual. This is the reference manual Yamaha dealers use in their service departments. It has all the necessary info to do any maintenance or repairs to your WR250R or X.

Seat Concepts dual-sport/adventure seat-kits incorporate a wider seating area for the rider, which results in more even weight distribution, while reducing pressure points. Each individual seat model has been specially designed to increase comfort without compromising ride-ability. The more aggressive the bike, the more aggressive the seat-kit.

Each kit contains detailed instructions for easy "Do It Yourself" installation. This provides the highest level of quality & comfort at an affordable price.

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.

Designed to enhance the appearance of your TW200, yet provide greater riding distance per tankful. This larger fuel tank has double the capacity of the stock tank at 3.6 Gallons, yet very slim and sleek. This tank has a custom design that will allow the use of OEM & Maier side covers. These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.

Comes with New Screw Cap.

Requires OEM/Stock petcock and oval rubber grommets for install.

If you do not have the grommets or if your O.E. grommets are in poor condition you can add these to your tank order.

Stock chain guard crack and crumble on you? Won't happen to this unit CNC machined from 2.5mm marine grade aluminum. Polished to a beautiful sheen that will give your DR that little twinkle as well as better protection.

Replace these any time you feel excessive play in the sprocket hub.

Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.

Sold as a full set.