Search Products

Protects AC lights from high voltage blowouts in systems with no battery

Deltran quick-connect plug with LCD voltmeter display. Plug this into your Battery Tender, or any SAE cable, for an LCD display of the battery voltage. Three LED lights indicate the state of charge as well.

Most fuel injected systems are very lean in their stock configuration. This is good for economy and emissions, but not performance. This unit allows you to adjust the Fuel/Air (F/A) ratio without remapping the ECU and getting into complicated software programs. The PowerJet Fuel Controller allows you to adjust the fuel map from -4% to +10% by selecting one of 10 built-in settings (including stock).

The device works by measuring the outside air temperature very close to where the stock sensor is located and then adjusts the signal from the OEM air temperature sensor to the ECU to make use of the Air Temperature Correction factor that is built into the stock ECU. The ECU is told that the intake air is a little cooler than it actually is and it responds by richening the injection map very slightly. How much depends on your setting on the PowerJet. This will result in improved throttle response, especially if you have an aftermarket exhaust of any kind.

PowerJet is easily installed by plugging it in between the stock AIT sensor and the bike's wiring harness under the seat. This can be done very quickly as they are exactly the same plugs. Unplug the stock connection, plug in the PowerJet on each side. The PowerJet fits easily under the seat behind the battery as it is rugged and waterproof. PowerJet comes with a full one year warranty.

The Dynojet Auto Tune kit is an "add on" accessory that can be used with any of our Power Commander V’s. It connects to the PCV with a single cable and requires only a ground and +12 volt connection to be made to install. If your exhaust does not already have one, a "weld in" O2 sensor bung is included.

Once installed, the Auto Tune kit monitors the fuel mixture (by installing the included Wide Band O2 sensor in the exhaust). It then sends this information to the Power Commander V and automatically corrects it while you ride. Each map that we offer has preset Air/Fuel ratio values included that we find to be the best overall settings. This lets you simply plug in the unit and let it do the work.

Tried, true and tested the Power Commander continues to evolve with the Power Commander 6.  Developed to simplify the user experience, PC6 makes choosing and tuning a map easier for the end user.  All the same benefits you have relied on for over 20 years remain to keep you at the front of the pack. 

The Power Commander 6 fuel injection tuning device allows you to optimize your fuel and timing curve (where applicable) giving you the confidence to roam freely.  With fine tune adjustability and multiple inputs, the Power Commander 6 will keep your vehicle running at its full potential letting you concentrate on the journey ahead.

Featuring a plug-and-play setup, Power Commander 6 can be installed discreetly underneath your seat, cowl, dash or other location ensuring your ride looks as good as it runs. Removing the device reverts your vehicle completely back to stock.  With the ability to store and switch between two maps on-the-fly  (via the map switch accessory) and connect to various Power Commander accessories such as the Autotune, Quickshifter or POD-300, the Power Commander 6 gives you features and functions that provide you with the ultimate ride.

All PC6 models have an end-user adjustment of +/-15 in the FUEL table and +/- 8 in the timing table (if applicable). This adjustment is on top of the values that are in the BASE map loaded to the device. This BASE map can be any of the available maps from the Dynojet website, or those you may have received from a third party.

Designed for use with stock engines using either stock or aftermarket exhaust and air filters.

• Provides a simple and affordable solution to carburetor tuning problems
• Allows you to tune your bike for increased power and smoothness while retaining fuel economy
• Includes a guide booklet on how to install and use your jet kit to it's full potential

Unsurpassed in airflow, dirt stopping and overall performance. Adding a pre-filter to your intake system gives you extra protection from damaging contaminants.

Hiflo filtro air filters are manufactured to fit the factory air box and are a direct replacement for original equipment filters. Top quality powerflow filtering media, developed for modern high performance engines.

• Fits directly into OEM airbox with application specific Sealing Bead to ensure a precise fit
• Fuel-management modifications are not required for increased performance
• Pleated media provides a large filtration area offering long service intervals
• Washable and reusable, pre-oiled and ready to ride
• Designed to provide increased performance

Included in this kit are the parts needed to repair a second generation TK carburetor. You get a new float bowl gasket, needle valve with O-ring, needle, mixture screw, and stock jets for the '01-'26 models kits.

This kit is for the REAR caliper.

• Kits contains all rubber parts necessary to rebuild one caliper.
• Kit includes: boots, seals, bleeder cap, brake pad retaining pins, and copper washers.
• SOLD as EACH

EBC Double H Sintered pads feature the HH friction rating - the highest in the industry.

Provides maximum brake effect and lasts twice as long as organic pads.

Replace those worn out brake pads with quality EBC replacements.

• The perfect brake pads for leisure use
• Offer maximum durability and excellent braking performance
• Constructed of U.S.-made sintered bronze for longest lifetime
• Best for riding in water, mud, dust, or sand

• Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability. These Aramid fibers have a high strength-to-weight, thermal stability and abrasion resistance to provide advantages over steel fiber-based products. They provide excellent stopping power without noise and rotor galling but still provide fingertip control and strong, predictable brake response.
• Double-H sintered metal brake pads feature the HH friction rating, the highest in the industry. These pads provide maximum brake effect and last twice as long as organic pads.
• Semi-sintered pads have an all new recipe containing 30% copper by weight with an organic matrix. This design combines the long life of a sintered pad with the great feel and lack of rotor damage common with full-sintered pads. These can be used to replace Kevlar or sintered metal compound pads.

These DP Standard brake pads are our OEM replacement sintered metal compound. Ideal for everyday use, both on and off-road. They provide excellent all-round braking hot or cold, wet or dry. Where applicable a high-tech ceramic heat shield is applied to the rear of each backplate to reduce the heat transfer into the fluid and prevent brake fade. They have one of the lowest wear rates on the market, very low levels of brake dust and no noise and no thermal cycle bedding-in required are also benefits of the DP Standard brake pads.

• Save time and money with this complete OEM quality fork bushing kit
• Kits include fork leg and slider bushings along with any needed snap rings, o-rings and copper washers

• Kit includes a pair of oil seals and dust seals; no bushings or other rebuild parts included
• Seals have been tested to over 1 million strokes in R&D development
• Every part meets or exceeds OEM quality standards
  
   

Genuine Yamaha fork seals and dust wipers.

Add a fresh set of inner and outer bushings for a complete fork restore.

Both kits include all bushings, snap rings, and washers.

Gen 2 kit also includes the necessary O-rings.

Gen 1 kits are OEM bushings, snap rings and washers.

The complete fork upgrade kit - Straight rate springs and Race Tech Gold Valves. Also includes a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.

A CNC machined fork brace to stiffen up the notoriously wimpy front end on the DR. Have more confidence in your front end on or off the pavement.

Split design means that installation takes minutes without having to remove the forks. Available in a black anodized finish.

Don't want to buy a new shock? This rebuild makes the stock shock about 10 times better. Cogent Dynamics takes a stock DR650 shock, tears it down, cleans it up, adds a hard ceramic coating, then rebuilds it with a completely new Shock Shaft Assembly with rebound damping adjustment.

Any aftermarket spring for your stock shock will fit on this shock. If you are currently using the original spring, you will want to order a stiffer spring to go with your new shock. 

Our 7.5 kg/mm rear spring is 16% stiffer than the stock one and is perfect for the majority of riders. If you are a larger rider, or carry a lot of gear or a passenger (total weight exceeding 250 pounds) you will probably want the 8.3 kg/mm rear spring which is 28% stiffer than stock.

This shock includes the Bling Ring preload adjusting ring AND the Thrust Bearing! This replaces the two stock preload/lock rings. This ring is CNC machined aluminum with the additional thickness to provide superior support on the shock body.

Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.

A pair of factory OEM o-rings for the valve covers. Your valve cover o-rings live in one of the hottest parts of the engine and have a pretty short life. Replace them on your next valve adjustment to prevent oil leaks.

Time to adjust your valves? Here are the O-Rings that fit in your Valve Covers on your Yamaha. Keep the oil inside your motor and grime out! This kit includes both O-Rings. Be sure to grab the feeler gauges and a special wrench to aid in adjusting your valves.

Includes all necessary top quality gaskets, and seals for engine rebuilds.

• Meet or exceed OEM specifications
• Highest quality materials
• Rubber coated spring steel head gasket, and soft steel base gasket

Top End Gasket Set is designed for a piston replacement job and includes:

• Head Gasket
• Base Gasket
• Intake Gasket
• Exhaust Gasket

Complete Gasket Set includes all the gaskets necessary to rebuild the entire engine and transmission, including valve seals.

OEM valve cover o-rings

In this kit you will get 4 factory replacement bolts to replace any broken or damaged clutch pressure plate bolts on your DR650.

It can be easy to over torque these bolts if not done properly. If one of these bolts is damaged on your DR650, we highly recommend replacing all 4 to prevent any future failures down the trail.

Stock bore replacement pistons from Wiseco. You have your choice of the standard compression ratio of 12.2:1, or a high-compression ratio of 13.5:1.

This high-compression kit will run perfectly with standard pump Premium.

Kits include piston, rings, wrist pin and circlips.

Raises compression from stock 9.5:1 to 10.5:1 for more power and snappier response. Highest quality Wiseco pistons are forged in the USA. Fits the standard size stock bore.

  As with any engine or exhaust modification, you will need to re-tune your fuel delivery system for optimum performance.

ProCycle 440cc BIG BORE 89mm KIT 2 With Cam Complete kit with 11:1 Wiseco piston (with rings, pin & clips), big bore cylinder sleeve, HotCams stage 3 camshaft and top end gasket set. You will have to have the larger sleeve installed in your cylinder.

• Includes pistons, ring sets, piston pins, retainer clips and head gasket
• Wiseco pistons are forged from aerospace aluminum alloys for reliable operation and longevity
• Hi-Compression pistons fit in the stock bore, providing a horsepower boost without the need for boring your cylinder
• Big Bore pistons requires boring/replating of the stock cylinder

The Total Tune-Up Kit. All the parts you need to do a complete tune-up on your beloved beast.

• Valve Adjustment Wrench
• Feeler Gauge set taper blades (.0012"-.040")
• Breather Filter
• 5-Pack of Oil Filters
• Magnetic Drain Plug
• O-Ring Kit
• Air Filter
• Spark Plugs

A set of four high quality valve stem seals.

Keep your motor running right with fresh spark plugs!

NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.

• High-quality materials and superior construction for serious power and reliability
  • Pure alumina silicate ceramic insulator provides high strength and better heat transfer
  • Deep-seated copper core for a wider heat range
  • Nickel alloy tip for longer life
  • Trivalent metal plating provides superior anti-corrosion and anti-seizing properties
• Choosing the right high-quality plugs prevents fouling from running too cool and preignition from running too hot
• NGK plugs available for almost every application and riding style

• Powercore silencers give your ride a deep works-like tone while providing optimum, dyno-tuned performance
• Silencer body is constructed of 6061-T6 grade aluminum with machined mounts and a clear anodized finish to bring out the shine

• Dual-muffler design exhaust system
• Achieves maximum performance, mass centralization, and rider usability
• Systems feature three-stage tapered headpipe for the best power gains, better throttle response and power delivery
• Vertical divider splits the exhaust gases more evenly for smoother flow to the mufflers for better mid-top power and throttle response
• Parallelogram-shaped muffler bodies increase muffler volume over the stock system for even crisper throttle response and reduced noise levels
• Systems meet AMA noise sound regulations right out of the box (AMA 2-Meter Max and Amateur 94 dB sound compliant)
• Muffler inserts are tunable to adjust power delivery and noise level

• The latest EVOLUTION of the popular LV ONE: aggressive sound and style
• Clean laser-etched Leo Vince logo in an innovative carved design (for the carbon fiber exhaust: bright aluminum die-cut high-temp resistant Leo Vince adhesive logo)
• Asymmetric design and high-tempiresistant full-carbon fiber end cap
• Impact-resistant sandblasted oval AISI 304 stainless steel sleeve – titanium look
• TIG-welded stainless steel front cup
• Adjustable full-carbon fastening strap
• Removable dB killer, weight savings and flawless installation

• Available in 52mm or 58mm lengths
• Kit contains two stainless steel exhaust swivel springs
• Free-floating mounting hooks to avoid breakage

• RS-3 Sound Insert for the Honda Monkey
• This new insert is designed to take the dB level down and fit perfectly with the RS-3 for the Monkey

Includes the Enduro Series RS-2 muffler and stainless steel header. This potent and versatile design is engineered to provide increased power and power delivery. The RS-2 has a pyramidal shape that features increased volume, and is a quieter system with a larger core — and it offers the added bonus of outstanding performance in a value-priced package.

The Akrapovic double-flow muffler is made of a Titanium outer shell with a Stainless Steel end cap. The joint on the inlet cap is CNC milled and connected to the inlet pipe with silicon-shielded tempered springs. A lightweight, compact and high-temperature-resistant carbon fiber clamp supports the muffler to the frame.

This muffler is 3 pounds lighter than stock and will give you an increase in power across the powerband.

The plug-and-play exhaust is simple to install without any need for remapping and comes with full instructions.

Motocross brake rotor featuring ultra lightweight radically profiled contours for great looks, great self cleaning and brake performance. Made with tough and durable heat treated stainless steel. Heat treated to perfection and then diamond ground to micron accurate surface finish and parallelism and will deliver great brakes that perform well and last.

The DR650 is rather hard on the cush drive rubbers. Replace these any time you feel excessive play in the sprocket carrier hub. Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier. Sold as a set of 6 rubber dampers.

Replace these any time you feel excessive play in the sprocket hub.

Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.

Sold as a full set.

The Magura Hymec Hydraulic Clutch system. Simply remove the stock perch, lever and cable and bolt this in its place. This system replaces the stock cable with a small lightweight hydraulic system for improved clutch control, easier operating pressure, a constant pressure point and smoother actuation. Developed over many years and tested under the toughest conditions possible in the off-road motorcycle world.

You will have to bypass your clutch safety switch to use this unit.

Never hurts to have a bit of the Margura specific Blood Red hydraulic fluid as well.

These tips are for the Warp 9 Shift Levers only. 

These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours.

You can also order just a new pin hardware kit which comes with new pin and clip.

Quality replacement levers. Standard length.

Quality replacement levers. Standard length.

Quality replacement levers. Standard length.

• Polished aluminum finish
• Quality Aircraft grade A-360 aluminum for strength & durability
• Designed to exceed OEM specifications, built to resist breakage
• Durable hard coating
• Designed to fit OEM master cylinder

• The new 3rd generation Motion Pro Revolver variable rate throttle system is here!
• Innovative reel changing system lets you tailor the throttle rate to your preference and riding conditions
• 5 different reels provide perfect throttle response for any condition. Use smaller reels for slower throttle rate and larger reels for faster throttle rate. Included cam reel provides progressive throttle response preferred by some riders
• Slim REV3™ throttle housing allows more room for lever clearance and adjustment to throttle housing position
• Improved throttle stop provides greater strength and durability
• Snap together elbows makes it even easier to install and change reels
• Cable boot keeps dirt and dust out for reliable and smooth operation
• REV3™ off-road kits are compatible with the new Motion Pro DirtControl™ V2 Lock-On grips and ODI Lock-On grips
• Billet aluminum inline cable adjusters ease installation and adjustment
• Lower section of cables use 5 mm housing with PTFE liner for reduced friction, increased routing flexibility and lighter weight
• Upper section of cables use 6 mm housing to provide solid support of adjusters
• Simple to install and maintain
• Patented

Kit includes:

• REV3™ throttle assembly with throttle tube (REV3™ off-road kits include the unbreakable Titan Throttle Tube™)
• Motion Pro REV3™ black vinyl cables specifically designed for your bike
• REV3™ sportbike kits include Motion Pro RoadControl™ grips
• Four interchangeable round reels: 35 mm, 40 mm, 45 mm, 50 mm
• Progressive cam reel - Sportbike kits include road race profile cam reel (orange)

Lost your side panel hardware? You aren't the first! We've got replacements. Two side panel screws, two special washers and the rubber insert that protects the side panel from the muffler.

• CNC’d and formed from aircraft grade 5052 aluminum
• Reinforces radiators to help prevent costly radiator replacement
• CNC’d billet bracket system incorporates rubber vibration isolators (most models)
• Lightweight, custom fit, tuck in cleanly behind radiator shrouds
• Simple bolt-on
• Mounting hardware included
• Made in the USA

FUZION guards feature the ultimate in hand protection with a unique design and flexible yet durable material. 

The expanded coverage area sweeps back toward your hand significantly increasing coverage making it perfect for cold, muddy or wet conditions. 

The FUZION features a unique two position mount and is constructed of molded light-weight closed-cell AEPE foam, which is crush-proof, water proof and extremely durable. 

The FUZION will work great for road of offroad riding, where wind deflection is important, and or bouncing off trees is a common occurrence. 

Kit includes mounts. Optional replacement mounts available.

• Essential protection for many late model adventure touring bikes
• Precision built for exact fit installation
• High Strength 25mm diameter powder coated aluminum construction
• All necessary hardware included

CNC’d and formed from aircraft grade 5052 aluminum. Covers and protects the rear brake master cylinder.

Protect your frame/paint from scuffs and scratches with these great Frame Guards from B&B Engineering  Made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.

B&B Off Road Engineering KTM 1290 Bash plate is made from 5mm thick 5083 structural alloy plate. Rear mounts are 5mm stainless steel with a rearward facing lug that rests on the rear frame rail to prevent rotation of the bracket. There are 6 32mm hole in the underside to help flush debris and minimize noise. There is also a rubber damper glued inside to help reduce noise. Bash plate can be fitted with or without genuine KTM crash bars. All necessary mounting hardware for this is supplied.

B&B Off Roads Kawasaki KLX250 & 300 bash plate is made from 4mm aluminium 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. 

All bash plates are supplied with the necessary stainless clamps and bolts where possible. 

All bash plates have a polished finish and have foam or rubber where required.

The Complete Doohickey Replacement Kit features the Doohickey supplied by Eagle Manufacturing, a torsion spring accompanied by a drill bit, a generator cover gasket, and an exterior cover gasket. Additionally, it includes all necessary components for rotor removal, along with a replacement bolt for reassembly.

ULTRA HIGH-PERFORMANCE HYPERSPORT TIRE

Avon's technological design and construction gives ultra high-performance handling and stability characteristics.

Multi-compound rear tire for all around performance.

Tubeless and V rated (for max speed of 149 mph)

A Radial tire specifically designed for small displacement sport bikes. Advanced belt design and Jointless Band (JLB) rear tire construction utilizes a continuously wound belt for smooth performance and a consistent tire contact patch. Aggressive sport-derived treat pattern for enhanced on-bike appearance.

These tires are all tubeless and H-rated (max speed of 130 mph)

Made for the true adventure rider, the K784 has everything you need to get you anywhere on or Off-Road.

• Tread pattern providing high traction on a variety of terrain
• Large tread blocks for improved tread wear and high speed handling
• High impact, Bias ply, casing structure providing a high level of puncture resistance
• Bias belted casing for improved handling & stability
• Rubber compound designed specifically for wet-slick & dry-hard packed terrain
• Picture provided for purpose of viewing treads.

Pirelli's Corsa radial or bias-ply with maximum grip tread.

Superb corning and straight-line stability.

Exceptional wet-weather performance.

Tubless design.

Light up your work area with this LED Flexible Light with Magnetic Base.

• Ultra thin, flexible, bendable and foldable
• Wrap it around, loop it over, set it down or use the magnets to hold it up
• Silicone construction body

Combines wrench and bleeder valve into one convenient and compact tool

• Fits most 8 mm bleeder nipples
• Bleeds brake systems and hydraulic clutch systems
• Internal check valve for fast easy bleeding
• Anodized billet aluminum handle with chrome moly steel body
• Compact size for tight spaces
• High quality internal seal
• Multi position handle

Order up your new levers here! If you keep breaking levers, you might want to think about a set of hand guards to protect them in case of a fall.

• Meets or exceeds OEM specifications
• Made from aircraft A-360 die cast aluminum

Filling and bleeding a Magura hydraulic clutch does not need to be a routine chore and should only need to be done when air infiltration within the system is suspected. Magura uses mineral oil, which does not absorb moisture from the environment, to lubricate the whole system.

Note: Magura hydraulic systems use ONLY mineral oil. Do not introduce DOT brake fluid of any kind into a hydraulic system designed to use mineral oil as this will cause corrosion to the internal seals and system failure may result. The only time anyone should ever need to replace the hydraulic fluid in a Magura system is following a hydraulic line exchange, a system upgrade, a crash which has damaged the system components or in a situation where a lack of fluid within the system has been diagnosed by poor lever feel.

If you do need to bleed your Magura hydraulic system, their custom made kit does indeed make that chore easier.

Slime Tube Sealant is formulated and tested for use in all tube tires. Once installed, Slime remains liquid and will not harden or dry out. Slime is guaranteed for 2 years.

As the Slime treated tube rotates, centrifugal force pushes the sealant to the tread area creating a layer of protection, repairing punctures as they occur and treating existing punctures. Slime is not intended for use in tubes losing pressure from sidewall punctures, bead leaks, damaged rims or faulty valves. Slime for tube type tires is not recommended for use in tubeless tires.

• Prevents and repairs punctures up to 1/8"
• Remains liquid inside the tire, coating the tread area as the tire rotates
• Non-toxic, non-hazardous, non-flammable, non-aerosol and water soluble
• Tubes treated with Slime can be patched with a conventional vulcanized patch using a bit of patience and care

Hydraulic Clutch Bleeder Kit includes 2oz of Magura Blood clutch fluid, 2 bleeder tools and fittings to properly bleed your hydraulic clutch. Great if you have air infiltration in the system or damaged it in some fashion.

A set of three OEM Suzuki front sprocket bolts. Thread-lock compound has already been applied for extra security.

This kit will replace your stock sprocket bolts and nuts with new hardware.

Factory Honda replacements in a convenient kit.

For all years.

• Machined from impact and wear resistant chromoly steel
• Heat treated, then finished with a nickel coating for corrosion resistance

• Constructed of the highest quality 1045 high-carbon steel
• Exclusive heat treatment and quenching process for strength and durability
• Nearly all machines come equipped from the factory with this sprocket
• The strongest, longest lasting steel replacement sprocket available

These turn signal relocation brackets from Yoshimura provide an easy way to move the stock turn signal lights or install aftermarket turn signals.

Combines with the Yoshimura fender elimination kit

Windscreen attaches to your bike's handlebars. Fully adjustable mounting brackets. Includes 7/8' handlebar clamps. 14" tall & 10" wide.

Will not fit 1 1/8" oversize handlebars.

Factory Replacement Body Plastics from Kawasaki

FunnelWeb ProLine Filter Highlights:

• Optimum air flow for increased riding time
• Improved engine protection
• Extended filter change intervals
• Simple to install, clean and re-oil
• Easy fitment

Like all FunnelWeb filters, the ProLine Filter features profile cut, single layer, single density foam that doubles the external surface area of the filter without increasing the original filter size. The ProLine Filter traps dirt, dust, sand and mud over a larger area on its outer surface, ensuring optimal air flow is maintained for maximized engine performance and reliability.

The single layer, single density polyurethane foam has the added advantage of being easy to clean and the ability to maintain its original shape after numerous washes. Overall, compared with conventional foam filters, FunnelWeb offers more protection from dirt ingestion, has longer service intervals and maintains high airflow rates when dirty.

The EJK evolved out of the need to address the ever-increasing complexity of factory fuel injection. For the newcomer to the market or professionals wanting an easier method for tuning fuel injection, the EJK is a customizable solution for the rider that wants to take control of their tuning needs.

This unit is a piggy-back EFI controller because it does not replace the stock ECU, but rather monitors the signals to the injectors and makes fuel adjustments based on the mode settings. The GEN 3 has a push button interface allowing access up to 6 different modes to allow for quick fine tuning by the end user without needing a computer.

Key Features:

• No computer or dyno needed!
• Plug and play, simple to install, base settings preset
• Unique load based technology
• Full range tunability available
• Does NOT interfere with stock ECU operation
• Simple push button adjustment interface
• Water-resistant 
• 2-Year warranty
• Compact size - 2.2" H x 3.4" W x 0.5" D

• Top-quality, abrasion-resistant UltraMax™ polyester
• Hi-visibility interior to help locate small parts, such as nuts and washers
• Heavy-duty, self-fastening strap for secure closure
• Small zippered pocket to hold smaller tools, bolts or screws
• Pockets range in various sizes to fit wide range of tools
• Elastic loops to hold CO2 cartridges
• Measures 13.75" x 10.5"

The ProCycle seat was designed for both comfort and function. Our seat is built with an advanced Progressive Density Foam (Pd-F) for those long days in the saddle, and also giving you freedom to move while standing. 

The wide and sturdy seat makes long rides more comfortable. The vinyl weave helps keep you cool by letting air flow between you and the seat. The front of the seat is narrower, giving you space for your knees when you're standing, while the sides have grip so you can hold on with your knees while riding. 

We will build the seat for you in-house on a new seat pan so all you have to do is put it on and go ride. Choose the heated seat option and we will add a Seat Warmer during the build process.

These wider seats from Seat Concepts help keep you comfortable on those long commutes or dual sport rides. The added width and improved foam density help keep your seat from being the item to stop you from going on those big rides or enjoying the bike.

The Complete Seats come fully assembled on an aftermarket seat pan, and are ready to install and ride.

• Durable steel wide foot pegs.
• Made of chromium molybdenum steel for extreme durability.
• Black powder coating finish

The IMS Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. 

They are the original Cast 17-4 Stainless steel pegs that revolutionized the foot peg market.

These pegs are 50mm(1.95") x 78mm(3.1"). 

Pegs Sit at Standard/OEM Height

Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty. Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever!

• Wider, lighter, stronger design
• Widest (mm) and lightest pivoting pegs on the market
• Upgraded heavy duty, long life springs
• Unique multi-directional grip pattern
• Outstanding build quality
• Expanded motorcycle fitment range
• Overhaul kit includes: 2 pivot bushings, 2 pivot tension springs, 2 lock nuts, 2 washers, 6 o-rings, 2 split pins and instructions

This is the ultimate adventure bike platform, it measures 2.25" wide, 4.75" long.

Patented adjustable collars make it easy to run them in the stock or lowered positions on most bikes.

Gain more room for bulky boots, or for longer legs. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long. Kamber bolts lets you adjust the 'tilt' of your pegs to increase comfort, or to give better squeeze on your bike.

Kit includes required fit kit.

• Tech-X footpegs provide outstanding performance and control by minimizing vibrations and adapting perfectly to the rider's foot movements
• Innovative rubber bearing between the tread surface and the joint
• Basic vibrations are absorbed and shocks on uneven terrain are mitigated
• Notches dynamically adapt to the corresponding weight shift, by being able to move forwards or backwards - accompanied by an intelligent damping system
• Increased safety and driving experience
• Unique serrated structure ensures reliable slip protection and allows unrestricted concentration on the road
• Parts are pre-assembled, making assembly easy
• Includes specific catch joint

2 high-quality bushings per set. They recommend changing bushings every 40 hours or at least once a year to get the best performance out of a set. If you are on an Adventure Bike and are doing a lot of road miles they recommend swapping out bushings once a year to ensure that you get the most vibration dampening of the bushings.

Every new set of pegs comes with a 90A bushing installed. This is a medium flex rating. 
80A is the softest and 95A lock-out is the stiffest and has the least amount of flex.

The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference. 

The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.  

For use on Motion Factory Foot Pegs Only

Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.

With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way. 
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.

The Swiftkicker is 100% manufactured in the USA from the highest quality components. 
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.

Measured from the center of the pivot to the bottom of the foot.

• Standard length travel range is 11.0"-15.0" (the middle of the travel is approximately the same length as the stock stand)

Motion Factory Racing patented Flex-Mount Footpeg System provides superior grip and allows your foot to flex forward and back with the movement or your motorcycle.

One of the key features of Flex-Mount Footpegs is their unique flex-mount design. This design allows the footpegs to absorb shocks and vibrations, reducing fatigue and improving overall comfort during long rides. Additionally, the adjustable height and angle options ensure a personalized fit, allowing you to find the perfect riding position for maximum control and stability.

The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference. 

They put an a90 bushing on all new mount setups so people can get a good feel for their mid range option. The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.  

Complete mount system includes: 

• 6061 Aluminum ADV Platforms (65mm wide x 107mm length) 
• Stainless steel mounts
• Sleeve bearing (8x10x20mm) included for 8mm OD' footpeg pins. 
• Right and Left spring included. 
• Chromoly steel spindles with reusable thread locker. 14mm wrench. Torque spec 40 ft/lbs 
• A90 (medium flex) rated bushings
• Cleats and stainless steel machine screws. M3x18mm. These can simply be replaced by going to your local hardware store when damaged or worn out. 
• Bushing bolts. 8mm Allen wrench. Torque spec 30 ft/lbs

 They designed their hardware to bend rather than break in a significant impact. A wrench or adjustable wrench will quickly and easily bend the bolt back straight. Please avoid using a hammer. A little leverage from a long-handled wrench or pipe will do the job. The whole system is rebuild-able and serviceable.

They Fit Kawasaki KLX110 and Yamaha TW200 however some of these bikes may need a little modification by yourself, Please check the size carefully before you buy. If you make mods to the footpegs for fitments it will void all warranties and return policies. 

Extra protection for your motor! Strong magnet at the end of the plug picks up ferrous metallic flakes in your oil, protecting your engine!

Replacement friction plates.

Aramid High Performance Clutch Disc Sets use aramid to add strength, reduce wear and increase life of the friction material; aggressive riders will benefit from the superior performance of race-proven aramid.

Limited to stock on hand.

Keep essential items easily accessible with the OBR ADV Gear Sherpa Tail Bag. The OBR ADV Gear Sherpa Tail Bag attaches to your motorcycles rear rack via an optional strap free base panel or by a series of adjustable buckle straps. A padded spacious main compartment is perfect for carrying those items you wish to keep close such as tools, cameras, documentation, rain jacket, etc. A smaller mesh lid pocket sits above the main pocket for storage of smaller items.

Features

• High strength, abrasion and water resistant ballistic nylon construction 
• Heavy duty #10 coil zippers with storm flap
• Secure attachment to your bikes rear rack via an optional strap free plastic mounting plate or adjustable buckle straps
• Spacious and padded trapezoid 9x10x5 main compartment 
• Secondary lid mesh pocket adds even more storage
• Three sided reflective webbing with Molle loops
• 4 external D-rings on top lid with 3mm shock cord gives you a place to put those gloves during a ride break

• Add convenient storage and function to your Adventure bike with these durable rear racks
• Laser cut from 12-gauge, grade 50 steel with durable matte black powder coat finish
• Multiple tie down locations and slots for bag straps or bungees
• Add additional storage capability with optional Adventure Rack Mounting Plates (sold separately)
• All mounting hardware and instructions included
• Rear rack weight limit 25 lb.

High Quality Replacement Wheel Bearings and Seals for your TW200.

Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.

Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.

Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.

Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.

Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.

The rubber coated outside diameter creates an optimum seal at the hub.

Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.

• The latest EVOLUTION of the popular LV Mufflers: aggressive sound and style
• Clean laser-etched logo
• Asymmetric design and high-tempiresistant full-carbon fiber end cap
• Impact-resistant sandblasted oval AISI 304 stainless steel sleeve
• TIG-welded stainless steel front cup
• Adjustable full-carbon fastening strap
• Removable dB killer, weight savings and flawless installation

Get better range from your early KLR650 by adding an IMS 6.6 gallon fuel tank. The big tank also provides radiator protection.

Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for the dunes or the race track! These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.

Natural color is recommended if you wish to easily see the fuel level in the tank.

This tank requires you to re-use your stock petcock valve. Does Not Use OEM/Stock Shrouds