Search Products

This box moves up the rev limiter allowing higher revs. It also has a hotter advance curve from the OEM box. This allows for a bit crisper throttle response and easier starting. This is a "must have" for modified KLX110's.

• Raises rev-limiter 1200 rpm over the OEM ignition
• Hotter advance curve for better performance
• Direct replacement for the OEM CDI ignition box

Choose mechanical or hydraulic brake switches for your dual-sport conversion

• Permanent battery leads with integrated battery status/charge system monitors for 12V lead-acid batteries or lithium batteries
• Monitor charge or confirm if the charging system is working correctly
• SAE charge port with weatherproof sealing cap
• Two automatic modes: battery charge level monitor and charging system test

Keep your smartphone, GPS and/or MP3 charged while enjoying your ride. Water- and weather-resistant, the Dual USB Port/Plug Charger offers you 5-Volt/2-Amp dual USB ports that have an inline fuse for protection. It comes with 38" of wire and 12" long battery quick connect rings. The mounting bracket that is included fits 7/8" and 1" bars.

This will give you a complete SET (Front and Rear) of brake pads.

• Sintered Pads are best for regular riding -long life, and good performance in all conditions.
• Sport Carbon pads are made for fast riding in dry conditions - not recommended for mud, water, or sand.
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered pads are high performance race pad with superb durability similar to that of the sintered pad. Higher friction level and fade resistance. Diamond ground surface finish to speed bed-in. Comes with new pad pins. Race Sintered are designed for racing use only; not for street use

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand

Kit includes front and rear brake pads.

EBC brake pad set.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads

• Aramid fibers have high strength-to-weight, thermal stability and abrasion resistance to provide advantages over cheaper steel fiber-based products
• Provide excellent stopping power without noise and rotor galling, even on polished rotors
• Fingertip control and strong, predictable brake response

DOUBLE-H SINTERED METAL PADS
Provide maximum brake effect and last twice as long as organic pads
Feature the HH friction rating – the highest in the industry

EBC Double H Sintered pads feature the HH friction rating - the highest in the industry.

Provides maximum brake effect and lasts twice as long as organic pads.

EBC brake pads contain aramid fibers; these are man-made high-performance fibers used widely for their light weight, high strength, abrasion resistance and thermal stability.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads.

Sport Carbon pads:  

• Carbon graphite "X" pads blended with Aramid for leisure/sport use
• Low heat generation
• Best for fast, dry riding; not for mud, water, or sand
• Offroad, Semi-sintered metal

Sintered Pads: 

• The perfect brake pads for leisure use
• Offer maximum durability and excellent braking performance
• Constructed of U.S.-made sintered bronze for longest lifetime
• Best for riding in water, mud, dust, or sand

Race Sintered:

• High performance race pad with superb durability similar to that of the sintered pad.
• Higher friction level and fade resistance
• Diamond ground surface finish to speed bed-in
• Comes with new pad pins
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads

Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability. These Aramid fibers have a high strength-to-weight, thermal stability and abrasion resistance to provide advantages over steel fiber-based products. They provide excellent stopping power without noise and rotor galling but still provide fingertip control and strong, predictable brake response.

Double-H sintered metal brake pads feature the HH friction rating, the highest in the industry. These pads provide maximum brake effect and last twice as long as organic pads.

Semi-sintered pads have an all new recipe containing 30% copper by weight with an organic matrix. This design combines the long life of a sintered pad with the great feel and lack of rotor damage common with full-sintered pads. These can be used to replace Kevlar or sintered metal compound pads.

Set includes pads for both front calipers.

Replace those worn out brake pads with quality EBC replacements.

Each kit includes all necessary rubber components and brake pins.

Each kit includes all necessary rubber components and brake pins.

Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.

• manufactured from unique ebc low carbon hpsr steel
• laser & cnc punched for lightness
• hardened and ground for precision braking
• nickel coated to resist corrosion

Complete bolt-on and go rotor assemblies. Made with forged aluminum center hubs high-friction billet steel rotor rings and sturdy riveted construction. Excellent choice when upgrading or replacing OEM brake rotors.

Sold in pairs.

Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.

The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!

• Accurately and quickly measures chain slack
• Two scales measure both chain slack and chain to swingarm clearance
• Setting chain slack properly dramatically improves chain life
• Lightweight compact design fits easily in your tool box or road kit
• Works on most street and dirt bike applications up to 75mm chain slack
• Made from engineered nylon with aluminum measuring scale
• Anodized laser-etched precision measuring scale
• Refer to your owner's manual for proper chain slack and procedure
• Patent pending

T-Rex stands are made from steel tubing finished in black powder for durability. Back by a 3-Year limited warranty for any material or manufacturing defects. Rest assured that you are getting best material commercially available.

Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools.

The basic purpose of a center stand serves to enhance ownership experience by easily raising the rear wheel completely off the ground for drive chain lubrication and adjusting, tire & tube patching/replacement and even FRONT wheel work. Those fortunate enough to have owned a motorcycle equipped with a center stand have come to learn the game-changing role it can play -even off-road.

Center stands have many more inherent uses including:

• Increased stability when parked on soft ground
• Easier cleaning and pre/post ride inspections due to the upright positioning
• Less effort required to place on its stand when compared to a milk crate or portable stand
• Superior parking/storage advantages in tight spaces

Unlike a basic portable moto stand, your center stand is ALWAYS available wherever your need it, whenever you need it.

When in use, this kit raises your rear tire 3/4" off the ground. When retracted, the stand tucks away, 100% unobtrusive to the rider and passenger. A robust retention spring ensures the stand remains retracted, even on the roughest trails.

Each kit comes with all hardware and detailed instructions. All parts are powder coated black with a fine texture

Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".

Inexpensive way of getting the factory look. Adds 1/2" of width to any standard foot peg. These will give you a much more stable platform when standing on the pegs.

Sold in pairs.

This kit combines common wide platform Yamaha YZ/WR foot pegs with brackets that are custom made to fit the TW200. If you are tired of standing on the stock skinny footpegs, get yourself a set of these fat boys and have pegs that match the tires on your T-Dub! For ultimate comfort, order the Pivot Pegz kit!

Simply unbolt your stock brackets and bolt these in their place. The bracket on the right side (brake lever side) is shorter than stock to correct the offset in the stock pegs. On kickstart models, the stroke of the kickstart lever is shortened slightly. Should you ever need to replace the pegs in the future, simply order pegs for the Yamaha YZ or WR 250/450.

Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty. Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever!

• Wider, lighter, stronger design
• Widest (mm) and lightest pivoting pegs on the market
• Upgraded heavy duty, long life springs
• Unique multi-directional grip pattern
• Outstanding build quality
• Lifetime Warranty*

Cat Crap is the #1 voted anti-fog on the market. Lens cleaner and anti-fog in one. Works for all lenses, eyewear, goggles, helmet visors, etc.

Now available in the original version or the Ultra version. The original uses the front two emitters for low beam and then switches to the rear two emitters for high beam. The Ultra uses the front two emitters for low beam and then runs all 4 emitters on high beam at a reduced wattage. Wattage is 38 watts on low and 38 watts on high.

This bulb uses 4 Cree XHP 50 emitters, capable of more than 2500 lumens each. At 5000 lumens on each function, this is the brightest Cyclops H4 bulb.

• All metal construction for bases and collars
• Better thermal efficiency 
• Better beam pattern distinction between high and low beams
• 5600k
• 38 watts 
• Removable metal base plate for easy install.
• Screw on connectors at driver
• Standard H4 connector
• High/Low Beams

*Universal part, Please check your application for fitment

This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a plug and play installation however a small amount of trimming on the backside of the plastic headlight shroud is required.

This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive). The high beam is amazingly bright eliminating the need for auxiliary lighting.

The materials, construction, and aesthetics are all top notch. You won’t be disappointed.

Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive

Replace these any time you feel excessive play in the sprocket hub.

Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.

Sold as a full set.

From Shinko Tires, the 705 Series are DOT approved Dual Sport tires designed for 75% street and 25% trail riding. A versatile tread pattern provides excellent wet and dry weather adhesion and the compound resists tearing while riding off-road. "R" in size denotes a radial tire.

Made for the true adventure rider, the K784 has everything you need to get you anywhere on or Off-Road.

• Tread pattern providing high traction on a variety of terrain
• Large tread blocks for improved tread wear and high speed handling
• High impact, Bias ply, casing structure providing a high level of puncture resistance
• Bias belted casing for improved handling & stability
• Rubber compound designed specifically for wet-slick & dry-hard packed terrain
• Picture provided for purpose of viewing treads.

This street-legal knobby from Pirelli has good stability and cornering precision thanks to the carcass stiffness. The tread pattern optimized for use on dirt and gravel roads, cross-country racing and desert tours. It has lasting off-road performance and knob tearing resistance due to the special off-road compound.

Motoz Tractionator Desert H/T series of tires are renowned for great traction and long wear life. These tires are designed to handle hard terrain, fast and rocky trails as well as gravel roads and desert hard pack. Tricky off-cambers, ruts and hard braking at extreme lean angles are no problem for this DOT approved tire.

Note: Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.

This is a great Dual-Sport tire from Dunlop. Designed for the true 50/50 rider. An Adventure product for the price-conscious customer. Full tread depth pattern designed for rigorous off-road use yields excellent traction on everything from hard-packed fire roads to soft single-track trails. Versatile tire performance allows riders to travel on the street and venture off-road. A tire equipped to go anywhere, the D605 is a value option for the all-around rider. DOT approved.

We offer two different types of SuperMoto tubes. The first are Standard Tubes and are meant to be used with standard bias-ply type tires, but can be used with radial tires also.

But, if you are running radial tires, like SuperMoto, or have a retro bikes with spoked wheels and radial tires, you probably want to run the 'Radial Tubes'. Front tubes fits 120/70 and 120/60 tires. Rear tubes fits 150/60, 150/70 and 160/60 tires. These have a metal valve stem.

Ideal for smaller street bikes or smaller SuperMoto wheels.

Offers safety, durability with a ratio of grooves that has been increased to improve the balance between grip and wear.

Grooves run from the center to the shoulder to facilitate the evacuation of water and offer good grip on wet roads.

Possibly the best value for smaller SuperMoto tires.

Bias-ply and tubeless, S rated (max speed of 112)

The Nomadic Rack is a favorite for dual-sport riders with ruggedness and ease of installation. This rack does not need to be removed for under-seat maintenance. The mounting area is large 11" x 10" and the rack weighs just under 3 lbs. It constructed of 16 ga. steel and fully welded, then powder-coated black with a shot-peened look. Has a rigid four point mounting system and doubles as a grab handle. Complete instructions and stainless steel hardware are included.

• CNC laser cut from light weight 1/8" 5052 Aluminum
• Easy installation, no modifications required
• Large 12" x 9" surface area
• Sleek low profile, and lightweight!
• Rigid 4 point mounting system
• RotoPax 1 gal or 1.5 gal compatible

You may purchase just the rack or you can order the Rack with the RotoPax Mount. If you really want it all, you can order the Rack, Mount and a Fuel or Water Container.

Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series CRF300L rear rack which measures 10 inches wide and 12 inches long.

Easy to Install

• Works great for mounting Pelican and Seahorse cases, or any other hard case. Givi compatible.
• Holes are in place to accept Rotopax mount with no drilling required.
• Stainless steel mounting hardware and instructions included.
• Fabricated with mild steel, MIG welded, and finished with a semi gloss black industrial grade powder coat.
• Weighs 3 lbs, 10 inches wide, 12 inches long.
• Works with stock tool bag. You can remove the seat with no interference from the luggage rack.
• Rear rack only, no Rotopax mount or side racks included.

The little tool bag that Yamaha provides behind the side cover is nice, but adding this Tool Tube to your TW will make it easier to carry some real tools! The ABS pipe is plugged on each end with waterproof expanding plugs. It is held to the frame of your TW with powder-coated steel straps and brackets. It provides a storage space of 3" ID x 10-1/2" long. Includes all hardware required to mount to your TW200.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 3 strong powder coated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approximately 13" long.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

Folding tip, forged aluminum shift lever from BBR Motorsports. Stronger and lighter than the stock shift lever.

• Strong forged aluminum construction
• Steel knurled folding tip (chrome plated)
• Anodized titanium finish
• 1/2" longer than stock

Folding tip, forged aluminum shift lever from BBR Motorsports. Stronger and lighter than the stock shift lever, with a beautiful anodized (titanium color) finish.

• Strong forged aluminum construction
• Steel knurled folding tip (chrome plated)
• Anodized titanium finish
• Laser etched BBR logo

Warp 9 Flex 3-Finger Levers are machined Billet, anodized and hinged levers with CNC machined master cylinder interfaces.

Adjustable reach allows customization to the rider's hand size.

Double hinge design allows lever to flex out of the way in most impact situations.

Pushrod or Bearing contact styles for smooth modulation.

OE style clutch lever.

• Quality Aircraft grade A-360 aluminum for strength & durability
• Designed to exceed OEM specifications, built to resist breakage
• Durable hard coating
• Designed to fit OEM perch

The elegant, open-end design makes these heated grips both stylish and functional. Highly efficient design, delivering warmth faster than traditional heated grips. Five-level temperature controller adjusts the grips accurately to avoid overheating. Specially selected rubber material resists the outdoor environment and provides a secure and comfortable grip. Even at high-temperatures, the grip remains resistant to damage. 

• Removable end caps allow for use as open-ended grips when needed
• For twist throttle applications
• Note: 12-Volt DC applications only.

Choose from the standard five level push button temperature controller, or the LCD display controller which shows the selected heat level and available battery voltage.

These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.

These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.

Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).

Protect your head pipe from rock damage. This stainless steel spine clamps to your head pipe to add a layer of protective armor between your vulnerable pipe and those nasty rocks or logs. Fits the stock headpipe. Will fit the FMF head pipe with the addition of larger clamps.

The EVO R series draws on our rich heritage of making power. Offered for various off road MX and sport ATV models, the EVO R is a tried-and-true series that will save weight, add noticeable performance gains and sound tremendously better than stock.

• Hard anodized oval shaped aluminum muffler
• TIG welded reinforced muffler bracket(s)
• 304 stainless steel mid pipe / head pipe
• Red powder coated stainless steel end tip
• Lighter than stock exhaust system
• Huge horsepower and torque gains
• Sleek muffler design allows for maximum clearance
• Removable screen-type spark arrestor included
• Handmade in the USA
• 1 Year Limited Manufacturer’s Warranty

New replacement side panels specifically made for TW200.

Sold in pairs, designed to be used with Maier USA Rear Fender.

New replacement side panels specifically made for gen 1 KLR650.

Available in 4 colors.

  Will not fit KLR250

Depending on your application and preferences, more than one optional heat shield may be useful.

Quality replacement headlight fairing for TW200

Universal off-road front fender. Must be drilled to fit your mounting bolt pattern.

This is the brace needed to stabilize the wing like structure they call a front fender on the KLR – both generations. This simple bolt-on reduces wind buffeting and increases steering stability at highway speeds. It also helps carry the weight of a fender mounted tool bag.

Made from laser cut 5052 aluminum, then CNC formed and beautified with a shiny black powder coat. Easily mounts in a few minutes using the included stainless steel hardware.

The Bajaworx Dakar Clear windshield for the KLR650 is designed to direct the wind over even the tallest of riders without compromising visibility. Decreased wind noise, reduced buffeting and more control in strong crosswinds make this a fantastic addition to your newer KLR.

• Constructed using 3mm aerospace grade polycarbonate
• Sturdy and rigid, will not rattle or vibrate when riding off-road
• Opens up dashboard area by over 50%
• Available in clear only
• Uses stock mounting holes, new mounting hardware included.
• Trimming of the stock fairing recommended (refer to installation instructions for more information)

Molded using a very durable, lightweight 1/8" thick polycarbonate - giving the windshield a high impact strength and making it shatter-resistant with a superior light transmission quality. Mounts quickly and easily onto the stock headlight cowling for a clean factory look. Drilling of the cowling is required, hardware is included. Removal for trail riding is also quick and easy.

Only Clear screens are available at this time.

Factory Replacement Body Plastics from Kawasaki

Genuine Keihin spring, washer, and oring for the fuel screw of FCR and FCR MX carbs.

Just the parts…
Fuel screw spring, washer, o-ring (fuel screw not included)

• Complete kit from Moose Racing to rebuild the OEM carburetor
• Each kit contains all necessary gaskets, O-rings, float valve and jets
• Supplied to Moose Racing by the same supplier the OEMs use

Included in this kit are the parts needed to repair a second generation TK carburetor. You get a new float bowl gasket, needle valve with O-ring, needle, mixture screw, and stock jets for the '01-'21 models kits.

Geared for the do-it-yourselfer that already has a TM40 or HS40. This kit supplies everything you need to convert it for use on your bike.

Kit includes intake and air boot adapters, throttle cables, choke knob, accelerator pump nozzle, a wide selection of main and pilot jets plus a TM40 tuning manual.

The Dynojet Auto Tune kit is an "add on" accessory that can be used with any of our Power Commander V’s. It connects to the PCV with a single cable and requires only a ground and +12 volt connection to be made to install. If your exhaust does not already have one, a "weld in" O2 sensor bung is included.

Once installed, the Auto Tune kit monitors the fuel mixture (by installing the included Wide Band O2 sensor in the exhaust). It then sends this information to the Power Commander V and automatically corrects it while you ride. Each map that we offer has preset Air/Fuel ratio values included that we find to be the best overall settings. This lets you simply plug in the unit and let it do the work.

A quality foam Air Filter to replace the stock one. Uses the same guide and frame as the stock unit. It requires foam filter oil to properly trap dirt particles. Don't forget the Evolution Air Filter Oil kit from No Toil.

• Designed to fit in the factory air box exactly like original filter
• The best selling replacement air filter for competition motorcycles and ATVs
• Unique two stage design allows for easy and complete cleaning
• Dual layer of foam, can be serviced separately
• Thin Ultra Seal base is virtually impossible to tear and has a built-in "Grease Groove"

Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 2 strong powdercoated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approx 13" long. Long enough to carry your Tire Iron Wrenches.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

Replacement handguards for your Cycra set up. Injection-molded high-impact plastic replacements. Includes all hardware needed for mounting.

The X-Factory Handguards from Acerbis are designed with a steel bar encased in an injection-molded Nylon composite. A replaceable dual-injected polypropylene shield attaches to the bar, providing excellent protection against debris and harsh conditions.

Included with the handguards is a universal mount kit, enabling installation on either 7/8" or 1 1/8" handlebars.

Will not fit XT250 with stock handlebars (oversize bars ok). Recommend Acerbis Rally Pro X-Strong to clear master cylinder.

The X-Grip is a frame guard that allows the rider to both protect the frame of the motorcycle from wear as well as adding more grip to the bike.

Made from a dual injected mold; The outer plastic is durable polycarbonate while the inner plastic is durable yet playable and offers incredible grip.

Available in 3 colors

This is one of the gnarliest skid plate made for the KLR. Made from 3/16" aluminum, it is laser cut and CNC formed. All seams are welded on both sides and the entire plate is black texture powder coated. Includes all the mounting hardware.

This is one of the gnarliest skid plate made for the KLR. Made from 3/16" aluminum, it is laser cut and CNC formed. All seams are welded on both sides and the entire plate is black texture powder coated. The plate mounts in minutes using stainless steel hardware.

IMPORTANT NOTE: The standard kit will work with all crash bars except for Givi and Happy Trails. Select the Givi option for that brand. This plate will not work with the Happy Trails crash bars.

Select the optional heavy duty mounting brackets if you want to replace the wimpy stock mounts with steel brackets.

These hand-crafted bash plates from B&B Eng. are constructed from 4mm 5083 aluminium plate. Strong and lightweight, this material has been selected because of its extreme suitability for welding, abrasion and impact resistance. All the necessary stainless clamps and bolts are included. Plate has a polished finish with foam or rubber where required.

This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug in the standard kit, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

This is all you need to not only change your oil, but protect your motor as well. We include a billet oil drain plug cap, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

• Billet Oil Drain Plug Cap
• O-Ring Kit
• 5-Pack of Oil Filters

The Total Tune-Up Kit. All the parts you need to do a complete tune-up on your beloved beast.

• Valve Adjustment Wrench
• Feeler Gauge set taper blades (.0012"-.040")
• Breather Filter
• 5-Pack of Oil Filters
• Magnetic Drain Plug
• O-Ring Kit
• Air Filter
• Spark Plugs

If you need a new clutch, you probably need a new gasket to seal that cover when you are all done. Genuine Yamaha part.

High quality steel rear sprockets from 39 to 53 teeth.

Sprocket color may differ depending on size.

High quality steel sprockets.

Stock Gearing: 15/48-128x128

Color may vary based on manufacturer availability, quality will not be compromised.

JT Sprockets is the world's leading manufacturer of aftermarket sprockets, constantly raising the industry's standards for quality and service. JT Sprockets are the only sprocket manufacturer using the ultra-durable high carbon C49 steel for rear sprockets.

High quality steel front sprocket

For reference, the stock gearing for the WR250R is 13/43 while the X model runs 13/42 stock gearing.

FREECOM 4 brings new standards to riding in duo. With explosive sound, extra tough shell, and incredibly flat design, nothing comes close to FREECOM 4 abilities on the real road. No wonder it quickly became the world’s best selling rider-to passenger communicator.

Features:

• Universal Bluetooth connectivity.
• FM radio, full phone connectivity
• Charge while riding
• Automatic Volume Control, Mobile conferencing
• Music & Radio sharing, GPS, music streaming
• Natural Voice Operation,
• Connectivity with two Bluetooth mobile devices, Hybrid & Corded Mic, VOX, Parallel audio streaming (Android only)
• Cardo Connect App (iOS/Android)
• Intercom bike-to-bike range: Up to 1.2Km (0.8mi)
• Intercom overall range: Up to 3.6 (2.2mi)
• 40mm JBL interchangeable speakers
• Battery capacity: 850mha
• Bluetooth 4.1
• Battery operations: 13hrs/1 week talk-time/standby
• IP67 waterproof

Don't want to buy a new shock? This rebuild makes the stock shock about 10 times better. Cogent Dynamics takes a stock DR650 shock, tears it down, cleans it up, adds a hard ceramic coating, then rebuilds it with a completely new Shock Shaft Assembly with rebound damping adjustment.

Any aftermarket spring for your stock shock will fit on this shock. If you are currently using the original spring, you will want to order a stiffer spring to go with your new shock. 

Our 7.5 kg/mm rear spring is 16% stiffer than the stock one and is perfect for the majority of riders. If you are a larger rider, or carry a lot of gear or a passenger (total weight exceeding 250 pounds) you will probably want the 8.3 kg/mm rear spring which is 28% stiffer than stock.

This shock includes the Bling Ring preload adjusting ring AND the Thrust Bearing! This replaces the two stock preload/lock rings. This ring is CNC machined aluminum with the additional thickness to provide superior support on the shock body.

Low shock also available. This option will lower your seat height 1" without the need for lowering links. All other features of this shock are the same as the stock height.

The Moab shock from Cogent Dynamics will change how you feel about your KLR. You may like it now, maybe even like it a lot, but you will absolutely fall in love with it once you mount up a Moab shock.

Spring duties are handled by a custom spring available in either Standard or Heavy-Duty weights. The Standard spring will be fine if you are under 250 pounds and don't ride with luggage or passengers often. Ride heavily loaded or with a passenger regularly and you will probably want the Heavy-Duty spring.

For a true comfort and performance package, we highly recommend upgrading your front suspension at the same time.

Race Tech shock springs in a wide range of spring rates to dial in your rear suspension to suit your weight (stock spring is 5.3 kg/mm). Recommended spring rates:

The V-Strom suffers from poor compression damping and limp rebound damping. The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.

• Bolt-on shock valving for riders serious about suspension performance
• Improves control, traction, plushness and bottoming resistance
• Improved, long-wearing, low-friction sealing design decreases fade
• Includes complete instructions

Precision tolerances – The tightest in the industry. Ultra-lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.

• The .85 springs are 30% stiffer than stock DL650 springs and 21% stiffer than DL1000 springs, a great choice for most riders.
• The 1.0 springs are 50% stiffer than stock DL650 springs and 42% stiffer than DL1000 springs, a better choice for heavier or aggressive riders, heavy loads, 2-up riding, etc.
• Stock spring rates for comparison: DL650-.65 DL1000-.70

Complete high quality kit to replace the bearing and seals in the DRZ400 shock linkage. Includes the lower shock bearing.

Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.

With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way. 
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.

The Swiftkicker is 100% manufactured in the USA from the highest quality components. 
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.

Measured from the center of the pivot to the bottom of the foot.

• Standard length travel range is 13.5"-19.5" (the middle of the travel is approximately the same length as the stock stand)

For those people who have been wishing for a dual petcock setup for their Acerbis 5.3 and 6.6 gallon fuel tanks. Install this kit to get the last bit of fuel from the right hand side of the tank without tipping the bike on its side. Includes the right hand fuel valve, o-ring, screws, tee fitting, fuel hose and spring action hose clamps. You will have to drill the hole in your tank for the petcock standpipe. For Acerbis tanks only.

You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of a big tank? The 3.7 gallon tank from Clarke might be just right. It's almost 5 lbs lighter and holds close to 1/2 gallon more fuel than stock to increase your range by about 20 miles. Fits with your stock petcock, Pingel or Raptor petcock.

Get better range from your DR650 by adding an IMS 4.9 gallon fuel tank. Available in Natural, White, Black and Blue. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap and fuel petcock.

A 5-pack of easy to use disposable funnels to help make any oil or fluid change cleaner and more precise.

• Engineered to keep your chain clean and lubricated under the harshest conditions
• The triple action formula cleans, lubricates and protects your chain - no matter if it's a standard or O-ring chain
• Engineered to adhere to your chain, on or off-road, and lasts long during those epic adventures
• The biodegradable solvent carrier helps clean chain and aids delivery of oil to micro-pores in chain
• Biodegradable oil penetrates and adheres to metal for an efficient, long-lasting lubricant
• Biodegradable wax seals in oil and keeps dirt off of your chain
• Biodegradable and non-toxic
• Available in 12-ounce (EU: 354,88 ml) aerosol cans

Auxiliary fuel tanks mount to handlebars, forks, or rear racks.

• Suitable for minis, trials bikes, full size bikes, and anywhere else a little extra fuel is needed.
• Each tank includes a siphon kit that connects the tank to the main fuel tank and automatically siphons fuel while the bike is being ridden.
• With this design, the auxiliary tank empties first, before the main tank.
• Does not interfere with headlight, handguards, rear seat, etc.

• Stealth license plate vanity light.
• Built-in turn signals.
• Running and Brake Lights.
• 218 LEDs ultra bright.
• 18 white leds. 1.5W max output.
• 200 red leds. 6W max output.
• 12v DC input.

Class 10.9 steel rotor bolts provide excellent sheer strength and include medium-strength threadlock patches to securely fasten your rotor.

Includes all the fasteners for both front and rear rotors.

Having the proper fork oil level is imperative to the handling of your bike. Setting the correct fork oil level is a snap with this fully adjustable gauge. The adjustable aluminum level plate can be set from 0 to 295mm. The oil reservoir has single milliliter markings up to 60ml.

Being able to accurately tune your forks by adjusting the oil level can make them better resist brake dive or bottoming. Oil level should be thought of as a fine tuning method to make your choice of spring rate work perfectly for your bike.

All that you need to repair and inflate your tire on the road or trail.

• Padded nylon zippered carrying case easily stores inside fanny pack or tool compartment
• Everything needed to repair and inflate tire on the road or trail
• 4" inflator hose accepts threaded cartridges only
• Each cartridge produces 8-9 psi
• Made in the USA

Kit includes:

• 1 - large oblong patch
• 2 - medium size patches
• 3 - small patches
• Thumb buffer
• 0.50 oz tube of rubber cement
• 5 - 4" rubber insert strips
• Insertion tool with screwdriver handle
• Reamer/rasp tool with screwdriver handle
• 3 - 16 gram 3/8" threaded CO² cartridges
• CO² 4" inflator hose

CO² cartridges cannot be transported on an aircraft.

Need to remove your clutch assembly to get at that dreaded neutral safety switch? This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub. Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut easy. All of that and no worries about doing any damage to your expensive clutch hub.

Bottom line, if you have to hold your clutch hub to remove it, there is no better way to do it.