DRZ400E

These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.

These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.

Replacement Halogen bulbs for mini style turn signals. Sold in a pack of 5 bulbs.

Roll-up pouch ideal for tucking away your lights when out on the trail.

Taillight and brake light Attaches to the top of the rear fender. Dimensions: 3 1/2" wide x 2" long x 3/4" tall. D.O.T. approved.

LED powered taillight, brake light, license plate light & license plate mount. Attaches to the underside of MX style rear fenders.

Taillight, brake light, & license plate holder (no plate light). Attaches to the underside of MX style rear fenders. Small and good looking!

Taillight, brake light, & license plate light. Attaches to the top side of enduro style (XR, KDX, etc) rear fenders. Dimensions: 2 3/4" x 4 3/4" x 2 1/2" tall. Wiring instructions included.

Taillight, brakelight, turnsignals, license plate light & license plate mount. Taillight is DOT approved, turn signals are not. Attaches to the underside of MX Style rear fenders. Turnsignals are embedded in the taillight housing. Wiring instructions included.
*Flushmount signals may require resistors to flash correctly

Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on 12-24 volt DC circuits.

Has both high and low beams. Attaches to the upper fork tubes with rubber straps. DOT and CE approved.

Here is an adjustable height centerstand from T-Rex Racing. If you are running supermoto wheels or lowering links, this centerstand will be much easier to use.

T-Rex stands are made from steel tubing finished in black powder coating for durability. Back by a 3-Year limited warranty for any material or manufacturing defects. Rest assured that you are getting best material commercially available.

Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools.

Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.

With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way. 
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.

The Swiftkicker is 100% manufactured in the USA from the highest quality components. 
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.

Measured from the center of the pivot to the bottom of the foot.

• Standard length travel range is 13.5"-19.5" (the middle of the travel is approximately the same length as the stock stand)

A must have for lowered bikes.

• Special Feature: Bigger kickstand shoe. 
• Extends approx. Stock length and shortens up to 4" for the DRZ400S
• Extends approx. 1.5" longer than stock and shortens up to 2.5" for the DRZ400SM
• Material: Steel tubing with black powder coated finish for strength and durability

Your choice of an aluminum bolt-on foot pad or a steel weld-on unit. Each will make the footprint of the stock side stand considerably larger, preventing your DR from tipping over in soft terrain. The bolt-on unit is cut from aluminum and then powder coated black, it comes with stainless steel mounting hardware.

The bolt-on pad and does require use of a drill for installation. The weld-on pad will need to be welded to the stand and then the entire unit painted for corrosion protection.

Inexpensive way of getting the factory look. Adds 1/2" of width to any standard foot peg. These will give you a much more stable platform when standing on the pegs.

Sold in pairs.

Not your average rubber insert! These rubber covers go over the top of your MK3 or MK4 Pivot Pegz so that the aggressive teeth are only exposed when you need them in muddy conditions.

• Unique, innovative design
• Wide flat platform
• Openings allow mud/dirt to pass through
• Easy and quick to get on/off
• Good grip
• Reduced vibration
• Extra comfort

Important to verify which style Pivot Pegz you have before ordering.

The IMS Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. 

They are the original Cast 17-4 Stainless steel pegs that revolutionized the foot peg market.

These pegs are 50mm(1.95") x 78mm(3.1"). 

• Each footpeg is cast, heat treated, and hardened from 17-4 stainless steel, given a solution annealing treatment, and age hardened for superior strength
• Width (57 mm) and length (90 mm); slightly convex platform for better boot positioning and grip when leaning forward or back
• Dual plane teeth provides traction without the "stuck" feeling
• Available with 1/2" rear offset to allow more space
• Made in the U.S.A.

• Durable steel wide foot pegs.
• Made of chromium molybdenum steel for extreme durability.
• Black powder coating finish

Services two Pivot Pegz and fits MK2, MK3 and MK4 Pivot Pegz

Kit Contents:

• Two pivot tension springs
• Two lock nuts
• Two washers
• Six o-rings
• Two split pins
• Pivot Pegz sticker and instruction sheet

Pivot Pegz have set a new standard in foot peg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.

Pivot Pegz aim is to build the best foot pegs in the world and they really do perform as good as they look. There's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.

• Mega wide 60mm platform
• Widest and lightest pivoting pegs on the market
• Open design = less mud packing
• Unique multi-directional grip pattern
• Outstanding build quality
• Race proven design and durability

From Warp 9, top of the line Adventure Pegs. a full 5" long and 2.5" wide will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a single track trail.

• Ceracote coated Chromoly steel pivot for the ultimate in strength
• Replaceable 7075 T6 Aluminum Platform
• Permanent Stainless Teeth provide the ultimate in non-slip traction
• Built-in bottle opener in the bottom!

  NOTE: These pegs DO NOT fit the '18 model!

Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.

This set of high quality replacement steering stem bearings includes:

• Upper and lower tapered bearings
• Upper and lower bearing races
• Upper and lower seals

• Designed to quickly and precisely remove outer bearing race from the steering head without the use of a hammer and punch
• Puller design ensures bearing is pulled perfectly straight to eliminate possible damage to frame
• Works on all tapered bearing races from 47 mm to 55 mm OD
• Precision machined anodized aluminum cup will not damage seal surface
• Brass bearing washers for easy use and long life
• Hardened steel jaws engage securely on inner bearing lip
• Lifetime limited warranty

Complete chain and sprocket replacement packages.

• JT steel sprockets
• EK SR06 O-ring chain

High Quality chain. Will need to be cut to fit your sprocket combination.

Always carry a spare master link when out on the trail.

  Master links are not interchangeable. Be sure to check the manufacturer and series on your chain.

These do not fit the TW200 or XT250. Only for 520 or 525 chains, Please verify chain size.

High quality steel front sprockets.

• Made exclusively from the finest Japanese SCM420 chromoly steel alloy
• Heat treated and hand finished to meet or exceed O.E.M. standards
• Outlasts any mild steel or surface hardened sprocket as much as two and three times over

High quality steel rear sprockets from 39 to 53 teeth.

Sprocket color may differ depending on size.

A set of six high quality grade 10 sprocket bolts with lock nuts. Thread-lock compound has already been applied for extra security.

These bolts are flat head style, requiring a countersunk hole in the sprocket.

Shield your bike’s vital drivetrain components with B&B Off Road’s heavy-duty front sprocket case saver. This premium guard, CNC-machined from high-strength 6mm aluminum plate, offers unparalleled protection against rocks, impacts, and other off-road hazards.

Uncompromising Strength, Precision Fit:
Engineered for maximum durability, this case saver boasts a 6mm main body crafted from 5083 structural aluminum – a material renowned for its resilience. Complementing this robust core is a 4mm thick front sprocket cover, ensuring comprehensive protection for your drivetrain.

Designed for Flawless Performance:
CNC machining guarantees a precise fit for both Suzuki DRZ400 (2000+) and Kawasaki KLX400 (2000+) models. This ensures seamless integration with your bike, eliminating concerns about interference or compatibility issues.

Peace of Mind on Every Ride:
Whether you’re navigating technical single tracks or powering through dusty plains, this case saver offers the confidence to push your limits. By safeguarding your front sprocket and surrounding components, it minimizes the risk of costly repairs and keeps you on the trail.

• Made from 5083 structural aluminum for durability
• 6mm thick main case saver body
• 4mm thick front sprocket cover
• All components CNC machined for a precision fit
• Fits 14 and 15 tooth sprocket

Replace your lower chain roller with this high quality roller with 2 sealed ball bearings. The stock roller has no bearings. It's just a plastic wheel riding on a bolt. Ball bearing chain rollers are smoother, quieter and last longer.

• Accurately and quickly measures chain slack
• Two scales measure both chain slack and chain to swingarm clearance
• Setting chain slack properly dramatically improves chain life
• Lightweight compact design fits easily in your tool box or road kit
• Works on most street and dirt bike applications up to 75mm chain slack
• Made from engineered nylon with aluminum measuring scale
• Anodized laser-etched precision measuring scale
• Refer to your owner's manual for proper chain slack and procedure
• Patent pending

Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.

Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.

The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!

• PBR = press, break, rivet
• Innovative design will press, break and rivet 520, 525 and 530 chains with one convenient tool (not for use on 428 chains)
• Versatile design will remove chain pins, press master-link plates and rivet hollow nose and soft nose (quad stake) master link pins on O-Ring and non O-Ring type chains
• Easy-to-use design allows you to change tool functions by simply moving the position of the anvil block
• Indexing letters on movable anvil and body ensures correct tool configuration; simply line up the letter on the anvil to the letter on the body to get the configuration you need
• All components conveniently store on tool when not in use
• All steel construction with heat-treated components for strength and durability
• May be supported in a vise or held with included handle
• Great for the professional technician or DIY mechanic
• Compact and light enough to carry in a tool bag for trail-side repairs
• Patent Pending

Can break or rivet chains from #35 to #530 like a pro.

kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.

kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.

NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.

This is without doubt the fastest, most effective, most meticulous, precise and systematic method for giving your chain a thorough cleaning. It forces its bristles between the plates where dried and hardened chain lube, road sand, glass, tar and other materials gather to form a hard shield of abrasive dirt where the O-ring meets the chain plates. 

• Chemical resistant nylon brush
• Flexible and adjustable
• 360 degrees of cleaning
• Compact size for easy storing

Note: Designed to be used with the engine off

Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.

• Will not harm O-ring chains
• Easily adjustable for all chain sizes

Introducing Oinker®, the revolutionary chain lube attachment for dirt bikes, street bikes, and ATVs. Say goodbye to messy lubrication. Oinker® attaches to any chain lube or wax, ensuring a precise and even application to both sides of your chain. This means minimal overspray, keeping your swing arm, rear tire, and brakes clean.

• Even and Accurate Lubrication: Their patented dispenser features exit holes that align with your chain's link plates, ensuring the areas that need it most get it.
• Minimize Over-spray: Keep your motorcycle clean and free of messy chain lube.
• Reduce Waste: No more over-lubing your chain. Their patented dispenser enhances the efficiency of your lubricant use.
• Rotatable Dispenser: Allows you to adjust your hand positioning. Ideal for bike's with chain guards.
• Durable: Constructed from glass-filled nylon, Oinker is strong, durable, and resistant to chemicals.
• Universal Compatibility: Fits any standard can of lubricant.

*For cans with an attached smart straw, you will need to replace it with the included nozzle

What's Included:

• 1 Chain Oiler
• 3 aerosol straws
• 3 replacement nozzle to be used only on cans that have attached straws.

Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.

This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).

Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.

Maximum master link width 24.8mm.

Will not damage master links, hardened steel pins for reliable use.

Light weight billet aluminum construction.

A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.

Fits 520, 525, and 530 pitch chain.

ULTIMATE SPROCKET WRENCH KIT

• 12” long wrench gives you more torque to get those thread locked sprocket bolts off easily
• Double ended 12mm & 13mm to fit all modern motocross, Enduro and dual sport bikes
• Dog leg wrench design allows wrench to easily clear rim edge and wide tires
• 8mm allen fits most Japanese bikes 8” long for extra leverage
• Torx T45 fits late model KTM and Husqvarna bikes, 8” long for extra leverage
• Vinyl coated handles to protect rim edge and give a non slip grip
• Makes routine sprocket bolt maintenance a quick and easy job

• Hardened metal rotor/disc locks resist cutting, sawing and chisel attacks
• Comes with carry pouch and a disc lock reminder cable
• Includes an extra mini flashlight key for three total keys
• Features a durable push button lock with high security anti-drill round key lock cores

The ABUS SmartX 8078 3D Alarm Disc Lock offers advanced Level 18 security, combining cutting-edge technology with exceptional protection for your bike. 

Featuring a 13.5mm double-locking sliding bolt made from specially tempered hardened steel, it delivers superior resistance to tampering. 

The 3D motion-sensing alarm emits a powerful 100dB sound to deter unauthorized movement, while the SmartX Bluetooth keyless lock system provides ultimate convenience. It seamlessly connects to the ABUS SmartX App, allowing you to monitor lock, alarm and battery status in real-time. 

The USB-C rechargeable battery ensures long-lasting performance and multi-color LED lights with audible signals keep you informed. The lock also features location memory from the last pairing, providing added peace of mind.

• Level 18 security
• 13.5mm double locking, sliding bolt
• 3D motion sensing alarm, 100db
• SmartX blue tooth, keyless lock system
• Connects to ABUS SMARTX APP for lock / alarm / battery status 
• Lock constructed from specially temper hardened steel
• USB-C rechargeable battery
• Multi-color LED light and audible signals inform about battery and lock status
• Location memory from last pairing

SMX Carbon Look Rotor

• Rotor material has higher friction than plain stainless steel for added stopping power
• Rotors measure 320mm
• Come with caliper relocation bracket
• Designed to fit standard hubs

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered pads are high performance race pad with superb durability similar to that of the sintered pad. Higher friction level and fade resistance. Diamond ground surface finish to speed bed-in. Comes with new pad pins. Race Sintered are designed for racing use only; not for street use

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered pads are high performance race pad with superb durability similar to that of the sintered pad. Higher friction level and fade resistance. Diamond ground surface finish to speed bed-in. Comes with new pad pins. Race Sintered are designed for racing use only; not for street use

This will give you a complete SET (Front and Rear) of brake pads.

• Sintered Pads are best for regular riding -long life, and good performance in all conditions.
• Sport Carbon pads are made for fast riding in dry conditions - not recommended for mud, water, or sand.
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads.

Class 10.9 steel rotor bolts provide excellent sheer strength and include medium-strength threadlock patches to securely fasten your rotor.

Includes all the fasteners for both front and rear rotors.

GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

• Each kit contains all necessary components to rebuild a master cylinder
• Made by Nissin, an OEM supplier in Japan

All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.

Made by Nissin, an OEM supplier in Japan

Replacement retaining pin for the brake caliper. Includes 1 stock style brake pin.

Be sure to use some anti-seize on the threads when you install it.

Front caliper only for DR350 and DR650

This anodized billet piece, brings a touch of color to your bike. Available in red or blue, it replaces the stamped steel clevis that connects your brake pedal to the master cylinder.

This brake bleeder makes bleeding your brakes a one man job.

The unique check valve allows fluid and air to escape while preventing air from re-entering the system.

Combines wrench and bleeder valve into one convenient and compact tool

• Fits most 8 mm bleeder nipples
• Bleeds brake systems and hydraulic clutch systems
• Internal check valve for fast easy bleeding
• Anodized billet aluminum handle with chrome moly steel body
• Compact size for tight spaces
• High quality internal seal
• Multi position handle

DRZ400 E/S

A pair of Race Tech fork springs to dial in your front suspension to suit your weight.

Fits all DRZ400 models with conventional forks (not for SM)

Recommended spring rates:

• Race Tech's original bolt-on fork valving system for front cartridge forks
• Triple the flow area of pistons
• Put valving control on the shim stack
• Outstanding tunability; improved control, traction, plushness and bottoming resistance
• Complete instructions, Gold Valve pistons, valving charts, valving shims
• Technical Edge Fork Maintenance and Gold Valve Installation video all included

Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes Fork Seals and dust wipers.

An excellent replacement for the stock fork boots. These are great for protection from dirt, rocks and other contaminants. These boots utilize the latest advances in material technology to adapt to fork and styling demands. These high quality fork boots are 1/4 the price of the OEM factory replacements.

Helps protect vulnerable fork tube and seal from dust, dirt, and corrosive elements. Hook & loop (Velcro) fastening on back side makes installation or removal for cleaning a breeze.

Race Tech shock springs in a wide range of spring rates to dial in your rear suspension to suit your weight (stock spring is 5.3 kg/mm). Recommended spring rates:

The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.

• Bolt-on shock valving for riders serious about suspension performance
• Improves control, traction, plushness and bottoming resistance
• Improved, long-wearing, low-friction sealing design decreases fade
• Includes complete instructions

Complete high quality kit to replace the bearing and seals in the DRZ400 shock linkage. Includes the lower shock bearing.

For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.

• Complete assembly, ready to install into the shock body
• Has air bleed holes to help remove air from the oil reservoir during installation
• Double-lip oil seal design keeps out dirt and keeps friction low
• Kits include aluminum body, dust seal, bushing, oil seal, O-ring, internal guide bushing/washer, snap ring, and top-out bumper

Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.

Complete high quality kit to replace the bearing and seals in the DRZ400 swingarm pivot.

Billet aluminum lowering links. Lowers the rear suspension.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.

The three forces of suspension, testing procedures, even the black arts of chassis geometry: This explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.

• Extracts dirt and debris trapped between fork seal and tube
• Easy way to keep fork seals clean and debris free
• Works on conventional and upside-down forks

Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers

• Knurled anodized aluminum locking ring
• Perfectly weighted to drive seals
• Carbon steel body halves

Showa removed the schrader valve on many newer rear shocks. Now you need a needle to recharge your shock with nitrogen after a rebuild. Race Tech built this unit just for that job.

The features of this tool include 300 psi capacity, bleeder valve and T-handle plunger pin chuck. Swivel chuck has a 12" flexible hose. Comes complete with instructions, carrying box and Schrader valve extension (required on some Showa shocks). Nitrogen bottles available at any welding supply house.

Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Head and mid-pipe are constructed from 304 stainless steel. Entire unit is pounds lighter than stock and gives great horsepower and torque gains throughout the RPM range.

All handmade in the USA with a 1 Year Limited Manufacturers Warranty.

Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Unit is pounds lighter than stock and gives gains in horsepower and torque throughout the RPM range. All of that in a package handmade in the USA with a 1 Year Limited Manufacturers Warranty.

The V2 Series Slip-On muffler features an aluminum body, TIG welded components, stainless steel inlet tube and a great new look. This Lightweight Slip-On weighs approximately 5.5 lbs.

The DG Performance systems offer increased throttle response, power and torque. Standard sound level is approximately 98 db. Equipped with a US Forestry approved spark arrestor.

The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.

• Uses long-life muffler packing for increased packing life
• Forest Service approved spark arrester

The Q4 employs intricate chambers, baffles and proprietary multistage packing material making it the best performing quiet muffler available.

Constructed from aircraft grade aluminum and high strength stainless steel.

Sound output 96dB. Several pounds lighter than the stock muffler.

Constructed from 304 stainless steel and breathes much better than the stock unit. Handmade in the USA with a 1 Year Limited Manufacturers Warranty.

The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels.

Their baffle was designed to replace the stock insert. The baffle produces a nice note compared to the de-restricted stock version and dyno test results showed an increase on 2 hp up top.

A noise test on the insert was conducted at the EPA Victoria Vehicle Test Station at Macleod under controlled conditions with Class 1 meters.

Some extra details:

1. The ADR test is conducted at an engine speed which is 50% of the engine rpm at which the engine develops maximum power. However, this engine speed is determined when the bike is in restricted form, with a throttle restrictor that stops the throttle being fully opened. This is why the ADR engine test speeds are so low. However, they are the engine speeds used to determine compliance.
2. On the ADR test, the B&B tip was over the signature noise emission, but a tolerance of 5 dB(A) is allowed before prosecution would be initiated. With this tolerance, the insert would not be prosecuted as it is just 4 dB(A) over the signature.
3. When tested with the standard OEM tips (as fitted when delivered from Suzuki Australia), the Suzuki came in at 95 dB(A) for the ADR test

Does not contain a spark arrestor. Check local laws on spark arrestors before purchase.

• Reduce exhaust sound by one to six decibels
• Options for DG V2 & RST and for the older "O" & "R" Series mufflers
• Easy installation; remove rear end cap and place Quiet Core in front of the spark arrestor
• Smaller diameter inserts are quieter but more restrictive; larger inserts are less restrictive but louder
• 1" Not recommended for RST
• Each size is sold separately

This Quiet Insert comes stock in all new FMF Q4 mufflers. If you lost yours, this is the replacement you need.

It will fit Q4, Q4 Hex, Powercore and Powercore Hex mufflers.

It will reduce the sound rating of the Power Core models, from about 99db down to about 96db.

Please choose the correct Insert for your muffler. If you are unsure of the year that your muffler was manufactured you can easily identify visually which insert you will need.

The headpipe gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head, thereby making them a single use part. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.

The muffler joint gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers (Q4 or PowerCore 4) do not require a joint gasket but the all other aftermarket mufflers as well as the stock muffler do require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.

Protect your head pipe from rock damage. This stainless steel spine clamps to your head pipe to add a layer of protective armor between your vulnerable pipe and those nasty rocks or logs. Fits the stock headpipe. Will fit the FMF head pipe with the addition of larger clamps.

This universal heat shield provides a great look at a great price.

• Fits all 1-1/2" - 2-1/8" Pipes
• Measures 7-1/4" x 3"
• We recommend Anti-Seize on all exhaust fasteners.

If your aftermarket exhaust is missing heat shield mounting points, this is the easy fix you’ve been waiting for. 

Includes one stainless steel mounting bracket with M6 threaded nut, and one stainless steel hose clamp.

Fits exhaust approximately 1.1inch-2inch diameter. Trimming may be required for smaller diameter exhausts.

Have you lost your stock heat shield, or need one on an aftermarket head pipe? FMF makes this nice unit that includes clamps, heat shield with the FMF logo and button head screws to hold it on. We recommend Anti-Seize on all exhaust fasteners.

Don't get burned! Giant Loop's ingeniously simple and effective exhaust shield protects bags and bodywork from heat damage. The Hot Springs Heat Shield helps avoid the meltdown, preventing bags and side panels from touching your bike's exhaust. It's the lightweight, universal heat problem-solver for virtually any motorcycle exhaust system. Backed by a Limited Lifetime Warranty.

The Chilly Exhaust Heat Shield is the most effective heat shield on the market. The innovative three piece design consists of a top shield attached to 2 rails with rivets and spacers. This reduces the contact area and slows down heat transfer. They have incorporated a patented, insulated reflective blanket on the underside of the shield to reduce radiant heat transfer. The included stainless steel clamp makes it simple to install.

We highly recommend a heat shield if you run soft luggage without hard racks.

FEATURES:

• Solid Top Shield - The logo is laser etched and there are no cutouts on the top shield. This prevents radiant heat from passing straight through to your luggage.
• Side Rails - By isolating these with spacers the heat conductive surface area to the top shield is reduced and slows down heat transfer.
• Radiant Heat Shielding - The reflective insulated blanket on the bottom of the shield is the real hero. This patented material won't be found anywhere else in the motorcycle industry. 
• Stainless Steel Clamp - Slots have been provided in the side rails to make installing as easy as it gets.
• Brushed Aluminum - Lightweight and looks nice.

DIMENSIONS:

• Length 7.5" (190mm) x Width 3.5" (76mm) x Height 1" (25mm)
• Clamp fits any exhaust 3.5" - 5.5" (89mm - 149mm)

The latest in muffler packing technology. Spec 31 high performance muffler packing resists breakdown up to 1400°F, is universal, and is easy to install.

• Kits come in 2 lengths - 15" and 19"
• Pillows can be trimmed to length to fit different mufflers.
• Includes a cap stuffer to fill packable end caps.

Re-pack your silencer with this pro-quality, three layer packing system and restore lost power and sound control.

Kit includes:

• 60"x20"x1⁄4" glass mat.
• 7"x20" stainless wool
• 8"x20" stainless mesh
• Twelve 3⁄16" rivets

• Copper-colored release agent and lubrication for machine elements which are subjected to high thermal stress
• Makes dismantling easy after long running times
• Outstanding thermal resistance
• Resistant to acceleration forces
• Outstandingly adherent
• Resistant to hot water, salt water and splash water
• Long-term corrosion protection
• Prevents brake noise
• Protects from welding and seizing
• Operating temperature range: -31°F to 2012°F (-35°C to 1100°C) .
• 3.53 oz (100 g) tube

A highly refined blend of aluminum, copper and graphite lubricants. Use during assembly to prevent galling, corrosion and seizing due to weathering or chemicals. Anti-Seize assures easier disassembly. Temperature range: -60°F to 1600°F (-50°C to 870°C). Salt, corrosion and moisture resistant – ideal for marine use. Meets Mil Spec #907E.

Replacement Exhaust Pipe Retention Spring

• This swivel spring replacement will work on nearly any exhaust system with a similar spring.
• Made from stainless steel, and has a high temp silicon sleeve to protect exhaust component finish.
• Made by Akrapovic, 60mm size, SOLD EACH

• Available in 52mm or 58mm lengths
• Kit contains two stainless steel exhaust swivel springs
• Free-floating mounting hooks to avoid breakage

Set your bike apart with a custom exhaust look. Withstands direct heat up to 2000°F.

• 2 inches wide and 25 feet long
• Available in black or natural
• 4 stainless steel tie wraps

Adhesive heat shield for your new side panel plastics to protect it from the heat of your muffler.

Depending on your application and preferences, more than one heat shield may be useful.

Dimensions: 2"x3'