Our offices will be closed on November 28 and 29 for the Thanksgiving holiday. We will be back on Monday, December 2.
The Kawasaki Versys-X 300 ABS has a liquid cooled, 296cc DOHC parallel-twin engine mated to a 6 speed wet multi-disk clutch. The Versys-X 300 ABS is intended to be a small displacement adventure bike and was released in 2017 and in 2019 the ABS model was released, with both models still in production. There are two versions of this bike, one with ABS and one without ABS, with the ABS function being the only difference between them.
| CHAIN SIZE | FRONT SPROCKET | REAR SPROCKET | FRONT TIRE | REAR TIRE | SPARK PLUG |
| 520x112 | 14T | 46T | 100/90-19 | 130/80-17 | CR8EIX |
Extra protection in bad weather to help keep your hands warm and dry. These nearly double the protection from most plastic type deflectors.
The outer shell is made from heavy-duty 500-denier nylon with 1/2" closed cell foam to keep the wind, cold and rain off of your hands.
Extend your comfortable riding season with Barkbusters BBZ cold weather protection handguards. Designed to fit with or without existing Barkbusters backbones or handlebar weights, these guards offer superb wind protection without limiting access to your grips or controls. Simple to install, they can be mounted or removed within ten minutes without permanent modifications. Ride with less bulky gloves in colder weather with the Barkbusters BBZ cold weather protection handguards.
Features:
Whats in the box:
It may not surprise you that they are covered with HippoSkin™, their waterproof outer shell, and insulated with a generous layer of HippoFat™, a warm, flexible, closed cell foam insulation—both are designed to keep inclement weather away from your hands.
Sold in pairs.
Hand/brush guards are required for proper fitment and for safety reasons.
Hippo Hands go on and off in seconds and never require tools or hardware.
The Backcountry is 9" deep.
If you like to stand and ride, this is the model for you! But… these hand covers also fit to just about any bike. They are also a great option for cruisers with hand guards or lever guards.
They feature a durable, quilted interior and flexible, neoprene cuff which ensures a great fit on so many bikes. The Backcountry is their smallest, most easily adaptable hand cover.
The Backcountry features a front reflective panel for higher visibility in low light situations.
The OBR ADV Gear Enduro ¾ Grip Mitt is your answer to cold fingers! Our ¾ open design terminates right at the wrist, but still offers full coverage of the hand while blocking the swirling air flow that freezes finger tips. Their ¾ open design does not cover important controls such as Hi/Lo Beam, Turn Indicator, or Kill Switches making this Grip Mitt perfect for both Off Road, Enduro, ADV, and ATV applications with full wrap hand guards.
Features
GET JumpStarter Mini, the second-generation, multifunctional jump starter. Now lighter and smaller, it's ready to help you restart any motorcycle or scooter when the battery is low. You can also use the powerful built-in LED flashlight or charge your use it as a power bank to charge your electronic devices. JumpStarter Mini comes together with a hard, water-resistant case perfect for carrying it anywhere and protecting it on your journeys.
A portable device that can jump-start your motorcycle or car. It can also charge your cell phone, GPS unit, laptop or other electronic devices via USB cable.
These Rider's Wrenches by Fredette are combination wrenches that have three wrenches in one! A 2-stroke size spark plug wrench - a front axle and a rear axle wrench. Yep, all three in one unit.
Available in the combinations shown that will fit virtually all current dual-sport machines.
A kit that includes an Axle Wrench combo for your bike with a 19mm for the front, and a 24mm for the rear. Just 7 1/2" long, it is long on leverage, but short enough to fit in even the smallest tool kit.
Also includes a pair of 'trail size' small tire irons.
Here is a set of 'trail size' tire irons. At 8-1/2 inches long they are small enough to fit in a fender bag with your spare tube.
Motion Pro T-6 Combo Lever has a hex box wrench for your axle nut on one side and a perfectly contoured tire spoon on the other. Manaufactured from lightweight forged T-6 aluminum with a hard anodized finish. These beauties are just under 10 inches long and weigh only 3.5 oz. Available in a 12/13 combo unit and a 22, 24, 27 and 32mm hex ends.
Our portable 12v compressor is perfect for any tool kit. This unit weighs only 14 oz and measures just 4"x2"x6".
Features a built in LED light and 0-120 psi gauge
• Comes with everything shown
The Mini-Morph is actually a bicycle pump, but it is the best manual compact pump for adventure / dual-sport riding. It has a fold-out foot and handle and a 4 inch hose so you can set it on the ground to pump!
This thing is small enough to stow away in just about any bag and go unnoticed until you need it to fix a flat or add air after a long arduous ride.
It seems that while packing for every adventure … we always end up with a few items that were either neglected to be packed, were last minute gear additions, or just needed to be packed in a readily accessible location…. The OBR Adv Gear Tool Pouch is the perfect solution for these miscellaneous items. Once packed the tool pouch can be slipped into any bag or attached externally using integrated webbing loops that are built into the pouch.
Features
* Tools not included
Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.
Thin wall bi-hex sockets designed to access narrow spark plug holes.
Fits 3/8" square drive and hex drive, 14mm, 16mm, 18mm, 21mm.
The Pro Fill Air Chuck from the people at Motion Pro is perfect for those tough to reach valve stems with its pivoting angled head. The design gives users extra hand clearance to avoid hot brake rotors or dirty chains. Billet manufactured from aluminum gives it a precise fit and function combined with light weight. It is finished off with a beautiful blue anodizing and then the Motion Pro logo is laser etched on forever. 1/4" NPT female inlet allows use with common air hose couplings and fittings.
A great addition to any tool box!
Changing tubes or tires without the right tools can be a real chore. Don't fight your snug beads any longer, use this 27" long tool that opens to 7-3/4" to provide the leverage you need to easily break your tire bead. Constructed from heavy-duty steel with comfortable no-slip grips, this tool makes the job a snap.
The Moose Tire Bead Tool holds your tire in place as you work you way around the tire
Made of aluminum with a nylon screw so it will not scratch the rim
Sold in pairs
No more fighting to keep the bead down while installing or repairing your off-road tires. The Bead Buddy holds the tire bead down in the drop center of the rim during tire changes making changes as easy as possible. Machined from tough 6000 series aluminum the Bead Buddy is light weight and compact enough for any tool pack. The Delrin securing thumb screw insures no scratches to your rims.
The Bead Buddy is NOT recommended for use with Bib Mousse tubes.
Available in 9.5" aluminum (ideal for travel) and 16" forged steel (useful in a home shop/garage)
Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.
The three forces of suspension, testing procedures, even the black arts of chassis geometry: This explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.
The MotoPressor Puncture Repair Tool combines the four tools essential for tubeless tire repair into a single tool.
With the motorcyclist in mind, they've designed a "4 in 1 multi-tool" that uses pre-vulcanized repair strings and packs into a sheath measuring a mere 130 x 68 x 50mm, that's small enough to fit in your pocket. The tool contains a pair of pliers, a rasp, an insertion tool and a sharp knife, which is all you'll need to fix 99% of punctures. The repair strings are pre-vulcanized, so they've done away with the "little tube of glue". The repair plugs the hole AND leaves a "patch style" repair on the INSIDE of your tire.
If you'd like to see the tool in action go just click HERE, and watch the demo.
Nitro Tape is a self-fusing silicone tape that's easy to remove with no residue.
It is waterproof, stretches up to 300%, has a temperature range from -65° to 500°F and insulates 8,000 volts per layer.
It resists UV, salt and corrosive chemicals.
20 mil thick, 1" wide by 10' long.
If you've split a radiator hose, this can help. A 'must have' for all tool kits.
Warp 9 stem puller
Here is a list of the features of their CNC machined tool.
This brake bleeder makes bleeding your brakes a one man job.
The unique check valve allows fluid and air to escape while preventing air from re-entering the system.
Combines wrench and bleeder valve into one convenient and compact tool
Features:
Keep your cables lubed up and working freely, with Motion Pro's Cable Luber. This tool is used to inject lubricant into any cable housing. Clamps over housing and cable allowing an aerosol can with nozzle to be connected. Once the lubrication solution runs out the far end, the cable is lubricated.
Designed to seal completely around the cable housing and stop all those messy leaks. With the unit closed and sealed around the cable, your cable gets better lubrication and you waste less lubricant.
A handy pocket size slide calculator from Mikuni to help you calculate jetting changes due to temperature and elevation changes. Will work for single and multiple cylinder machines whether 2 or 4 stroke. Also includes a guide for determining rich or lean conditions.
Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.
Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.
The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!
Can break or rivet chains from #35 to #530 like a pro.
kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.
kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.
NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.
Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.
Features:
This bright and compact 6-LED flashlight plugs right into your SAE battery charging socket for hours of light. In addition, it has a charging system check that lets you know if your bike is charging properly. It features a 40 inch cord so you can see in those out of the way places when you need to.
Quick release one-piece clamps that saves space. These are great for fuel lines, controlling wires, and can be used many times.
Comes with 4 each of 8mm, 9mm 10mm, and 12mm.
No special tools needed, from Helix Racing.
Made from medium carbon steel with hardened jaws. It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. Made by Motion Pro.
This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.
The Phillips type screws used in Japanese motorcycles are actually Japanese Industrial Standard (JIS) screws are very easy to strip if you are using a regular Phillips screwdriver.
This is a high quality Motion Pro T-handle driver with #1, #2, and #3 JIS bits made from S2 tool steel. There is bit in each end of the driver held in place magnetically. These are 1/4" hex drive heads so you can use all common driver bits as well. The narrow drive head profile easily fits into tight locations. Main shaft is 8.5" long and is chrome plated for protection.
Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on 12-24 volt DC circuits.
Having the proper fork oil level is imperative to the handling of your bike. Setting the correct fork oil level is a snap with this fully adjustable gauge. The adjustable aluminum level plate can be set from 0 to 295mm. The oil reservoir has single milliliter markings up to 60ml.
Being able to accurately tune your forks by adjusting the oil level can make them better resist brake dive or bottoming. Oil level should be thought of as a fine tuning method to make your choice of spring rate work perfectly for your bike.
Features:
The Phillips type screws used in Japanese motorcycles are actually Japanese Industrial Standard (JIS) screws and are easy to strip if you are using a regular Phillips screwdriver.
Here is a little kit that will make removing and replacing JIS screws much easier. Includes 2 each of JIS No. 1, No. 2 and No. 3 bits.
These will work in other bit holders and have a mild magnetic tip.
Use this tool to check for air leaks in two-stroke engines. It includes air pressure gauge, pump-up bulb and most fittings and adapters for single and twin-cylinder two-stroke motorcycle engines. Packed in a convenient carrying case with instructions.
The GCAG handles are comfortable to pull so whoever is helping will pull harder, and they are soft against your fender so you won't have any annoying bouncing, noise, or graphics damage.
GCAG dirt bike lift strap handles are constructed of 1" thin nylon webbing with flat stainless steel tri-glides for attachment. The grip section is built with 1" climb-spec tubular nylon webbing and a comfort grip handle.
Features:
Light up your work area with this LED Flexible Light with Magnetic Base.
Ever had to turn back on the trail because of downed limbs? Or have you ever been moto camping and needed some wood for a fire?
This is the tool for you then! We have tried this manual chainsaw and it makes quick work of hard woods like Oak.
The chain itself is 25 inches long with 8 inch nylon straps at each end. All together this saw weighs 1/4 of a pound. This will tuck away nicely into any tool pouch or saddle bag as it roll up into a tight round.
Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.
This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).
Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.
Maximum master link width 24.8mm.
Will not damage master links, hardened steel pins for reliable use.
Light weight billet aluminum construction.
A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.
Fits 520, 525, and 530 pitch chain.
Originally developed for premixing 2 stroke fuel, the Ratio Rite is a must have for EVERY shop.
Calibrations also include oz., c.c.’s and pints on the opposite side for transmission oil, fork oil, engine oil, etc.
Total capacity: 24oz
Includes storage lid
Latex free gloves for the shop or garage.
Showa removed the schrader valve on many newer rear shocks. Now you need a needle to recharge your shock with nitrogen after a rebuild. Race Tech built this unit just for that job.
The features of this tool include 300 psi capacity, bleeder valve and T-handle plunger pin chuck. Swivel chuck has a 12" flexible hose. Comes complete with instructions, carrying box and Schrader valve extension (required on some Showa shocks). Nitrogen bottles available at any welding supply house.
For easy removal of recessed oil filters.
Conical point screws pierces and grabs the metal end cap of the filter.
reduces potential damage to the engine cases.
NOT for use on re-usable oil filters.
Maintain your chain or sprocket, even change your rear tire or wheel while out on the road without the need for a center stand, with the BikeMaster Liftstick. Handy and convenient to carry. Perfect for street, dual sport and trail use. Liftstick includes non-slip rubber boots, which protect your motorcycle's swingarm from any scratches while claws at the base provide traction and stability during use.
The Snap Jack is an easy to use, portable, sturdy jack for chain lubricating, adjustment and chain drive maintenance. Also, simplifies cleaning. It can lift the rear tire up to 1/2" to allow the tire to spin freely. Includes front brake locking strap and handy carrying bag.
7" wire twisting pliers with return spring mechanism for easy and safe wire twisting.
A must have when blazing new or old trails!
This Super Siphon has a (1/2 inch x 6 foot) long hose, which makes it quite easy to transfer fuel from one bike to another! Simply, shake the hose to prime it and get fuel moving. The hose is resistant to gasoline and any other hazardous chemicals. Roll it up, stuff it in your bag and you will be very happy whenever you need it.
A professional level adjustable spoke torque wrench. Range from 0 to 62 inch pounds. The handle has a rubber coated end to protect your rims from scratches. Includes Torque wrench, standard handle (for tough disassembly work) and seven different size tips, all packed in a protective case.
Includes Tips 5.1, 5.6, 5.8, 6.1, 6.3, 6.5, 6.7, 6.8, 6.9 and Spline drive.
Convenient professional grade spoke wrench, a great addition to any tool pouch.
Recommended for use with Warp 9 wheels. Please measure nipple size to ensure proper fit.
Precision cut from heavy gauge material.
Extremely durable design.
Push/Pull design for hard to reach places.
Soft but durable PVC coated handle.
ULTIMATE SPROCKET WRENCH KIT
Use simple leverage to easily lift your dirt bike up on to a flat platform.
The platform angle adjusts easily so either wheel can be off the ground quickly and safely for work or cleaning. These adjustments can be made with the bike on the stand.
Folds up for easy storage and transport.
Adjustable legs for use on any terrain and allows for even lift height for any dirt bike.
Closeout item, as is, no warranty.
Thread Chasers are designed to clean and re-cut damaged aluminum threads.
This kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.
Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.
Uses 8mm or 10mm hex sockets, a Must for all tool kits.
The Giant Loop Tow Strap is a multi-functional tool that helps get you or your riding friends out of sticky situations.
This Cordura® Ballistic tow strap, designed with sewn loops on each end, can be girth hitched around a tree, bumper, rock, etc.; or used with footpeg-to-footpeg or other motorcycle (and snowmobile, ATV, snow bike) towing techniques. Constructed in the USA from ultra-durable custom woven Cordura® Ballistic webbing, which folds up into a compact integrated cover made with 22 oz. vinyl-coated polyester, or what they like to call “truckers tarp.”
Doubles as a quick deploying, super-strong ridge line for pitching a shelter tarp.
Color may vary based on manufacturer availability, quality will not be compromised.
A compact and lightweight solution to eliminate the SNAP for a safer tow. If you have ever towed a motorcycle you are familiar with the snap that comes with a traditional tow strap. GCAG made the Dynatow with a section that gives 32 inches of stretch so both riders have an easier tow.
The 26 foot total length gives you enough room to maneuver around obstacles and allows the freedom to choose better lines if you are towing in the gnar.
You can also use this as a recovery strap. You can girth hitch the loop end to the bike and throw the other end to a friend to pull. The dynamic properties of the Dynatow will help assist the pull. All of this functionality fits in a flat pouch about the size of sandwich and only weighs 12.8 oz. Throw it in your bag and be prepared.
Specifications:
Please consider the following before use: Practice before you need to use this product. Always inspect your Dynatow strap before use and NEVER use a worn strap. They recommend a proper training class to learn safe methods for towing a motorcycle.
Simplify self recovery with this quick deploy Z-Drag kit. It can sap your energy trying to get your bike unstuck. It can also fall in a way that makes it very difficult to pick up. The Z-Drag is a common rig to give you a mechanical advantage for reduced pull. The combination of roller cams provides a 4:1 pulling ratio for self recovery and a 5:1 ratio when you have help. A laminated instruction card is included in the bag.
| Quick Deploy | No knowledge of rigging and knot work required. Our Z-Drag comes out of the bag rigged and ready to use. |
| Color Coded | For simple operation. |
| Locking Carabiners | Two climbing rated, locking carabiners for secure attachment. |
| Lightweight | Approx. 3 pounds and small enough to pack on a motorcycle. |
| Strong | Even though its small, it still has a 1000 pound working load. |
| Versatile | With a 74' mainline you will always have enough length to get creative in a tough situation. |
| Multi-Function Bag | The bag features MOLLE compatible webbing on the outside for external attachment. The bag can also be utilized as a dead man anchor. |
| Storage | Comes in a 1000D Cordura storage bag. |
| Recovery | Can be used for solo recovery or with help from friends. |
| Trail Repairs | Can easily be used to hoist your bike from an overhead support for repairs and maintenance while traveling. |
| Clearing Trails | Move fallen trees out or other obstacles out of the way. |
| Camping | Can be used to hoist a bear bag, act as a ridge line for stringing a tarp, etc. |
3.5MM X 20FT
Made from Tough but lightweight 12 Strand SPECTRA / UHMWPE
2200LBS Break Strength
Double Looped Ends
Each Looped end is Covered in a Kevlar Sheath to protect the rope from abrasion
A must for getting your wheels straight, concentric and true. For use with a truing and balancing stand.
Dial Indicator Features:
Magnetic Base Features:
Kit Includes:
Always wanted to build or true your own wheels? Maybe just be able to balance your wheels after changing tires. This stand is perfect for both of those tasks.
Made from precision-drawn, chrome-vanadium tool steel, the BikeMaster® 9-Piece Ball End Hex Wrench Set and Holder features a bead-blasted surface for a better grip and a corrosion-resistant coating. They have a ball end, allowing an angled reach and access to obscured bolts. It comes with a durable holder and manufacturer's lifetime warranty.
Comes with sizes 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm and 10mm
Our latest casual t-shirt with a classic ProCycle Logo on the front and a topo map of our favorite local riding spot on the back. High quality soft t-shirt perfect for everyday wear.
T-Shirt Specs:
Similar to our Adventure Shirts, this super soft hoodie features our logo on the front and our Topo design on the back. Perfect for those cool evenings or brisk days.
The current ProCycle logo on front, with the design on the back showing our favorite 'Pavement Ends' sign with the DR rider continuing up the road on the pegs, ready for an adventure!
ProCycle's custom calendar features specially selected customer submitted photos from around the world. Real riders on real adventures.
Each of the two calendar sizes will feature different pictures. Even more reason to get both!
The desk top is 6" by 3.75" the perfect size to sit on your desk.
The wall calendar is 12" by 18" when fully open for use on any wall. Marks USA holidays and moon cycles.
The three images featured are the finalists in this years photo contest who will all be featured in the wall calendar for 2025.
Keep your head warm while you're not wearing your helmet on those colder days. Our premium waffle knit beanie is available in black or olive green.
Comes complete with our custom ProCycle embroidered patch.
Not sure what to get the adventure/ dualsport rider in your life?
How about a ProCycle Gift Card!
Load as much as you would like in $25 increments. This is a digital gift card, we will send you the information and redemption code via email once the order is processed.
*please allow 1-2 business days after the order is placed to receive the email containing the details and redemption code.
**If you would like a physical certificate to give as a gift instead of the digital code, choose USPS First Class Domestic for shipping at checkout, otherwise please choose curbside pickup and we will email you the redemption code and instructions for no shipping cost.
Keep track of your keys easier with our embroidered patch on a keychain.
Finished with metal ring with eyelet and merrowed border.
Patch measures 1.5" x 5"
As pictured; includes:
| 2 | Classic Swingarm Stickers (1% power gain) |
| 1 | Sheet of 3 small "black" stickers |
| 1 | Sheet of 3 small "yellow" stickers |
| 2 | "Adventure Begins Here" stickers |
| 1 | "Back Roads or No Roads" magnet |
Our logo on a 20oz double wall 18/8 stainless steel thermal tumbler with copper vacuum insulation, threaded snap-fit lid, and powder coated finish.
The copper plating on the inner wall is an extra defense against temperature transfer. Heat escapes much slower so your hot coffee stays hot even in a snow storm, and heat enters much slower so your ice water doesn't melt even under a blistering summer sun.
We have tested this bottle with 160° water placed on it's side for 7 hours mimicking being in a saddle bag with coffee from the morning campsite. The bottle did not leak when the lid was properly secured and the water only dropped to 113° at the end of our test.
Pair it with the OBR bottle wrap for even better value and have a holder on your luggage for your new bottle for ease of access and security.
Ballistic nylon padded construction absorbs vibration and shock protecting your radio from abuse. The updated design is longer now, to accommodate our radios with extended batteries. Each bag also comes with a foam block to properly position radios without extended batteries. Zipper top closure keeps the radio secure.
The Rugged Radios bag is built to perform in tough environments.
Fits: R1, RDH-X, V3, RH5R
Does not include handheld radio.
Walkie-talkie compatibility keeps you connected to friends and family on the trails! The MOTO-MAX kit is manufactured to strict standards and made to take on extreme offroad environments.
With heavy electrical shielding, genuine Nexus Military-grade connectors and a handlebar-mounted Push-To-Talk button, this race kit offers no-compromise communications and full operation without ever having to take your hands off the bars or the trail.
MOTO-MAX is the go-to communication solution for hardcore riders.
Compatibility:
Works with all GMRS/FRS radios operating on the same frequencies, including but not limited to GMR45, GMR25, GMR2, and more.
Business License is required. Click here to learn more.
Kit Includes:
