KLX125: Tools

Ready to go tool kits. Just toss it in your bag and hit the road... or the trail.

GET JumpStarter Mini, the second-generation, multifunctional jump starter. Now lighter and smaller, it's ready to help you restart any motorcycle or scooter when the battery is low. You can also use the powerful built-in LED flashlight or charge your use it as a power bank to charge your electronic devices. JumpStarter Mini comes together with a hard, water-resistant case perfect for carrying it anywhere and protecting it on your journeys.

• Light and compact multifunctional mini starter
• Allows restart of motorcycles and scooters when they are out of battery
• Can also be used as a Power Bank for electric devices thanks to the USB output port
• USB 5V2.4A output allows connection to tablets, smartphones, MP3 etc.
• Has built-in LED flashlight
• Easy to use; provides special protection against overvoltage and inversion of power supply polarity
• Start current: 200A, peak current: 400A, operating temperature range of -20°C to 60°C
• Includes JumpStarter, Smart Cable, 3-in1 USB cable and user instructions
• Measures 155 mm x 79 mm x 16 mm

A portable device that can jump-start your motorcycle or car. It can also charge your cell phone, GPS unit, laptop or other electronic devices via USB cable.

• XP-1 is 6" x 2 7/8" x1" 14oz.
• XP-3 is 5" x 2 7/8" x 1" 12oz.
• Holds a charge for up to 1 year.

• Designed to quickly and precisely remove outer bearing race from the steering head without the use of a hammer and punch
• Puller design ensures bearing is pulled perfectly straight to eliminate possible damage to frame
• Works on all tapered bearing races from 47 mm to 55 mm OD
• Precision machined anodized aluminum cup will not damage seal surface
• Brass bearing washers for easy use and long life
• Hardened steel jaws engage securely on inner bearing lip
• Lifetime limited warranty

These Rider's Wrenches by Fredette are combination wrenches that have three wrenches in one! A 2-stroke size spark plug wrench - a front axle and a rear axle wrench. Yep, all three in one unit.

Available in the combinations shown that will fit virtually all current dual-sport machines.

A kit that includes an Axle Wrench combo for your bike with a 19mm for the front, and a 24mm for the rear. Just 7 1/2" long, it is long on leverage, but short enough to fit in even the smallest tool kit.

Also includes a pair of 'trail size' small tire irons.

Here is a set of 'trail size' tire irons. At 8-1/2 inches long they are small enough to fit in a fender bag with your spare tube.

Motion Pro T-6 Combo Lever has a hex box wrench for your axle nut on one side and a perfectly contoured tire spoon on the other. Manaufactured from lightweight forged T-6 aluminum with a hard anodized finish. These beauties are just under 10 inches long and weigh only 3.5 oz. Available in a 12/13 combo unit and a 22, 24, 27 and 32mm hex ends.

Our portable 12v compressor is perfect for any tool kit. This unit weighs only 14 oz and measures just 4"x2"x6".

Features a built in LED light and 0-120 psi gauge

• Comes with everything shown

The Mini-Morph is actually a bicycle pump, but it is the best manual compact pump for adventure / dual-sport riding. It has a fold-out foot and handle and a 4 inch hose so you can set it on the ground to pump!

This thing is small enough to stow away in just about any bag and go unnoticed until you need it to fix a flat or add air after a long arduous ride.

It seems that while packing for every adventure … we always end up with a few items that were either neglected to be packed, were last minute gear additions, or just needed to be packed in a readily accessible location…. The OBR Adv Gear Tool Pouch is the perfect solution for these miscellaneous items. Once packed the tool pouch can be slipped into any bag or attached externally using integrated webbing loops that are built into the pouch.

Features

• Heavy duty industrial material construction with high strength UV resistant nylon webbing
• Heavy duty #10 coil zipper that won’t jam up in the dust
• External reflective webbing with Molle loops
• Pouch dimensions 5” x 13”

* Tools not included

Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.

Thin wall bi-hex sockets designed to access narrow spark plug holes.

Fits 3/8" square drive and hex drive, 14mm, 16mm, 18mm, 21mm.

The Pro Fill Air Chuck from the people at Motion Pro is perfect for those tough to reach valve stems with its pivoting angled head. The design gives users extra hand clearance to avoid hot brake rotors or dirty chains. Billet manufactured from aluminum gives it a precise fit and function combined with light weight. It is finished off with a beautiful blue anodizing and then the Motion Pro logo is laser etched on forever. 1/4" NPT female inlet allows use with common air hose couplings and fittings.

A great addition to any tool box!

Changing tubes or tires without the right tools can be a real chore. Don't fight your snug beads any longer, use this 27" long tool that opens to 7-3/4" to provide the leverage you need to easily break your tire bead. Constructed from heavy-duty steel with comfortable no-slip grips, this tool makes the job a snap.

• A tool to keep open up the bead when replacing a tube.
• Works smoothly even with the toughest beads.

The Moose Tire Bead Tool holds your tire in place as you work you way around the tire

Made of aluminum with a nylon screw so it will not scratch the rim

Sold in pairs

• Durable 6061 aluminum with blue anodized finish and laser engraved logo
• Used to push the tire bead down into the drop center of the rim on off-road wheels while using tire tools to change tires
• Hooks over spoke and pushes bead down on opposite side of tire from tire irons
• No more fighting to keep bead down while installing off-road tires

No more fighting to keep the bead down while installing or repairing your off-road tires. The Bead Buddy holds the tire bead down in the drop center of the rim during tire changes making changes as easy as possible. Machined from tough 6000 series aluminum the Bead Buddy is light weight and compact enough for any tool pack. The Delrin securing thumb screw insures no scratches to your rims.

The Bead Buddy is NOT recommended for use with Bib Mousse tubes.

• Innovative multi-use tire tool set
• Breaks the bead on most street and off road motorcycle tires
• Integrated tire spoon for tire removal and installation
• Light weight and compact size is perfect for tool packs
• Ergonomic handles with crossguard to keep hand from riding forward
• Forged 7075-T6 aluminum construction for strength and durability
• Black anodized finish
• Patent pending

Available in 9.5" aluminum (ideal for travel) and 16" forged steel (useful in a home shop/garage)

Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.

The three forces of suspension, testing procedures, even the black arts of chassis geometry: This explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.

The MotoPressor Puncture Repair Tool combines the four tools essential for tubeless tire repair into a single tool.

With the motorcyclist in mind, they've designed a "4 in 1 multi-tool" that uses pre-vulcanized repair strings and packs into a sheath measuring a mere 130 x 68 x 50mm, that's small enough to fit in your pocket. The tool contains a pair of pliers, a rasp, an insertion tool and a sharp knife, which is all you'll need to fix 99% of punctures. The repair strings are pre-vulcanized, so they've done away with the "little tube of glue". The repair plugs the hole AND leaves a "patch style" repair on the INSIDE of your tire.

If you'd like to see the tool in action go just click HERE, and watch the demo.

Nitro Tape is a self-fusing silicone tape that's easy to remove with no residue.

It is waterproof, stretches up to 300%, has a temperature range from -65° to 500°F and insulates 8,000 volts per layer.

It resists UV, salt and corrosive chemicals.

20 mil thick, 1" wide by 10' long.

If you've split a radiator hose, this can help. A 'must have' for all tool kits.

• Resists extreme environments; won't melt up to 500°F; remains flexible to -60°F
• No adhesive; fuses only to itself
• Forms a water- and air-tight seal
• Tensile strength of 600 psi
• Insulates to 400 Volts/Mil
• Tight insulating tape is 1" wide x 10' L and stretches to three times its length

• Large display, readings are shown to 0.1 psi
• Kpa and Kg-cm2 scales also provided
• Reads up to 99 psi
• Ergonomic shape fits nicely in your hand

Warp 9 stem puller

 Here is a list of the features of their CNC machined tool.

• Stainless Steel tip, wont break like softer brass tip
• Ribbed head for easier core removal
• Core tip threads into handle to protect tip from damage
• Includes spare valve core in handle for easy trail side repairs
• Tapered handle ends to make tip removal easier with gloved hands and non square edge doesn’t damage tool bags

This brake bleeder makes bleeding your brakes a one man job.

The unique check valve allows fluid and air to escape while preventing air from re-entering the system.

Combines wrench and bleeder valve into one convenient and compact tool

• Fits most 8 mm bleeder nipples
• Bleeds brake systems and hydraulic clutch systems
• Internal check valve for fast easy bleeding
• Anodized billet aluminum handle with chrome moly steel body
• Compact size for tight spaces
• High quality internal seal
• Multi position handle

Features:

• 2-ended design combines brush and pick with a curved spade to help vehicle clean off mud and debris
• Curved spade for the big stuff
• Brush head to clean controls and radiator
• Pointed tip for foot pegs and hard to reach places
• Includes a hanging hole for easy storage in the garage
• Ergonomic handle is made from durable ABS plastic
• Patented design

Keep your cables lubed up and working freely, with Motion Pro's Cable Luber. This tool is used to inject lubricant into any cable housing. Clamps over housing and cable allowing an aerosol can with nozzle to be connected. Once the lubrication solution runs out the far end, the cable is lubricated.

Designed to seal completely around the cable housing and stop all those messy leaks. With the unit closed and sealed around the cable, your cable gets better lubrication and you waste less lubricant.

• Works on most cables with a 4mm - 8mm O.D. housing.

• Contains degree wheel, standard unit indicator, adjustable magnetic stand, and three positive stops (10 mm, 12 mm and 14 mm threads)
• Can be used to install and adjust timing of any cam
• Wooden carrying case

A handy pocket size slide calculator from Mikuni to help you calculate jetting changes due to temperature and elevation changes. Will work for single and multiple cylinder machines whether 2 or 4 stroke. Also includes a guide for determining rich or lean conditions.

• Accurately and quickly measures chain slack
• Two scales measure both chain slack and chain to swingarm clearance
• Setting chain slack properly dramatically improves chain life
• Lightweight compact design fits easily in your tool box or road kit
• Works on most street and dirt bike applications up to 75mm chain slack
• Made from engineered nylon with aluminum measuring scale
• Anodized laser-etched precision measuring scale
• Refer to your owner's manual for proper chain slack and procedure
• Patent pending

Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.

Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.

The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!

• PBR = press, break, rivet
• Innovative design will press, break and rivet 520, 525 and 530 chains with one convenient tool (not for use on 428 chains)
• Versatile design will remove chain pins, press master-link plates and rivet hollow nose and soft nose (quad stake) master link pins on O-Ring and non O-Ring type chains
• Easy-to-use design allows you to change tool functions by simply moving the position of the anvil block
• Indexing letters on movable anvil and body ensures correct tool configuration; simply line up the letter on the anvil to the letter on the body to get the configuration you need
• All components conveniently store on tool when not in use
• All steel construction with heat-treated components for strength and durability
• May be supported in a vise or held with included handle
• Great for the professional technician or DIY mechanic
• Compact and light enough to carry in a tool bag for trail-side repairs
• Patent Pending

Can break or rivet chains from #35 to #530 like a pro.

kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.

kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.

NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.

Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.

• Will not harm O-ring chains
• Easily adjustable for all chain sizes

Features:

• Versatile, light and super compact chain tool for adventure touring and long distance trail riding
• 6061 billet aluminum body, complete tool weighs only 230 grams (8 oz)
• Will break 520, 525, and most 530 chains and master links (maximum link width of 20 mm)
• Included steel press plate for removing and installing clip style press-on master link plates
• Innovative dovetail closure provides ease of use and superior strength
• Hardened steel thread insert on body provides strength and durability
• Includes durable cloth pouch for easy transport on your adventure
• Requires use of a 12 mm and 14 mm wrenches (not included)
• Does not rivet master links.
• We recommend using the Motion Pro PBR Chain Tool if you have a rivet style master link

This bright and compact 6-LED flashlight plugs right into your SAE battery charging socket for hours of light. In addition, it has a charging system check that lets you know if your bike is charging properly. It features a 40 inch cord so you can see in those out of the way places when you need to.

Quick release one-piece clamps that saves space. These are great for fuel lines, controlling wires, and can be used many times.

Comes with 4 each of 8mm, 9mm 10mm, and 12mm.

No special tools needed, from Helix Racing.

Made from medium carbon steel with hardened jaws. It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. Made by Motion Pro.

This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.

The Phillips type screws used in Japanese motorcycles are actually Japanese Industrial Standard (JIS) screws are very easy to strip if you are using a regular Phillips screwdriver.

This is a high quality Motion Pro T-handle driver with #1, #2, and #3 JIS bits made from S2 tool steel. There is bit in each end of the driver held in place magnetically. These are 1/4" hex drive heads so you can use all common driver bits as well. The narrow drive head profile easily fits into tight locations. Main shaft is 8.5" long and is chrome plated for protection.

Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on 12-24 volt DC circuits.

• Use this tool to check and adjust the oil level on conventional and single chamber cartridge forks
• Adjustable ring will measure oil levels from 0 to 300 mm in 5 mm increments
• Syringe has a capacity of 60 ml
• New plunger head design features two fluorocarbon elastomer X-Ring seals that provide superior sealing and chemical resistance
• Billet aluminum plunger knob with durable black anodized finish
• New plunger head design allows easy cleaning and replacement of seals

• Extracts dirt and debris trapped between fork seal and tube
• Easy way to keep fork seals clean and debris free
• Works on conventional and upside-down forks

• Integrated shutoff valve allows precise amount of liquid to be dispensed
• Graduation marks for cubic centimeters, fluid ounces and premix ratio
• 1000 cc (34 oz) capacity
• Easy to understand premix ratio graduations for 32:1, 40:1, 50:1, and 60:1 for 1 to 3 gallons
• Adjustable ball-pivot spout allows easy, spill-free filling
• Top cover keeps dust and dirt out when not in use
• Magnet allows funnel to be stored conveniently on the side of your tool box
• Large molded handle for secure grip
• Reduced neck keeps funnel from dripping residue when funnel is laid on its side

Features:

• Two tools in one. One end is used to loosen stuck hose, the other end assists in pulling the hose off the fitting
• Reduces the possibility of damage to hoses and related components
• Lock nut at base of each tip allows 360 degree adjustment or removal of one tip for use in tight spaces
• Compact aluminum handle provides solid grip and excellent control
• High-quality steel tips with durable black oxide coating

The Phillips type screws used in Japanese motorcycles are actually Japanese Industrial Standard (JIS) screws and are easy to strip if you are using a regular Phillips screwdriver.

Here is a little kit that will make removing and replacing JIS screws much easier. Includes 2 each of JIS No. 1, No. 2 and No. 3 bits.

These will work in other bit holders and have a mild magnetic tip.

Use this tool to check for air leaks in two-stroke engines. It includes air pressure gauge, pump-up bulb and most fittings and adapters for single and twin-cylinder two-stroke motorcycle engines. Packed in a convenient carrying case with instructions.

The GCAG handles are comfortable to pull so whoever is helping will pull harder, and they are soft against your fender so you won't have any annoying bouncing, noise, or graphics damage.

GCAG dirt bike lift strap handles are constructed of 1" thin nylon webbing with flat stainless steel tri-glides for attachment. The grip section is built with 1" climb-spec tubular nylon webbing and a comfort grip handle.

Features:

• Quick tool-less install
• Stainless steel hardware (no metal contacts your fork tubes)
• Comfort Grip Handle
• Fits any bike

Light up your work area with this LED Flexible Light with Magnetic Base.

• Ultra thin, flexible, bendable and foldable
• Wrap it around, loop it over, set it down or use the magnets to hold it up
• Silicone construction body

Ever had to turn back on the trail because of downed limbs? Or have you ever been moto camping and needed some wood for a fire?

This is the tool for you then! We have tried this manual chainsaw and it makes quick work of hard woods like Oak.

The chain itself is 25 inches long with 8 inch nylon straps at each end. All together this saw weighs 1/4 of a pound. This will tuck away nicely into any tool pouch or saddle bag as it roll up into a tight round.

Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.

This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).

Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.

Maximum master link width 24.8mm.

Will not damage master links, hardened steel pins for reliable use.

Light weight billet aluminum construction.

A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.

Fits 520, 525, and 530 pitch chain.

Originally developed for premixing 2 stroke fuel, the Ratio Rite is a must have for EVERY shop.

Calibrations also include oz., c.c.’s and pints on the opposite side for transmission oil, fork oil, engine oil, etc.

Total capacity:  24oz

Includes storage lid

• No figuring
• No guessing
• No mistakes

Latex free gloves for the shop or garage.

• 10 Pack

Showa removed the schrader valve on many newer rear shocks. Now you need a needle to recharge your shock with nitrogen after a rebuild. Race Tech built this unit just for that job.

The features of this tool include 300 psi capacity, bleeder valve and T-handle plunger pin chuck. Swivel chuck has a 12" flexible hose. Comes complete with instructions, carrying box and Schrader valve extension (required on some Showa shocks). Nitrogen bottles available at any welding supply house.

For easy removal of recessed oil filters.

Conical point screws pierces and grabs the metal end cap of the filter.

reduces potential damage to the engine cases.

NOT for use on re-usable oil filters.

Maintain your chain or sprocket, even change your rear tire or wheel while out on the road without the need for a center stand, with the BikeMaster Liftstick. Handy and convenient to carry. Perfect for street, dual sport and trail use. Liftstick includes non-slip rubber boots, which protect your motorcycle's swingarm from any scratches while claws at the base provide traction and stability during use.

• Made of heavy-duty steel with a powder-coated finish.
• Available in black or red.
• Extends from 12.5" - 18"

The Snap Jack is an easy to use, portable, sturdy jack for chain lubricating, adjustment and chain drive maintenance. Also, simplifies cleaning. It can lift the rear tire up to 1/2" to allow the tire to spin freely. Includes front brake locking strap and handy carrying bag.

7" wire twisting pliers with return spring mechanism for easy and safe wire twisting.

• 25ft of .032 stainless wire
• T302/304 Stainless steel
• Great for securing nuts, bolts and grips
• A must have in the shop or tool box

A must have when blazing new or old trails!

• Soft rubber handle
• Thumb latch release for safety
• 8" blade, 9" folded length
• Steel frame

This Super Siphon has  a (1/2 inch x 6 foot) long hose, which makes it quite easy to transfer fuel from one bike to another! Simply, shake the hose to prime it and get fuel moving. The hose is resistant to gasoline and any other hazardous chemicals. Roll it up, stuff it in your bag and you will be very happy whenever you need it.

Tips fit

• Spoke Torque Wrench
• Spoke Wrench Handle

Machined from tool-grade steel.

A professional level adjustable spoke torque wrench. Range from 0 to 62 inch pounds. The handle has a rubber coated end to protect your rims from scratches. Includes Torque wrench, standard handle (for tough disassembly work) and seven different size tips, all packed in a protective case.

Includes Tips 5.1, 5.6, 5.8, 6.1, 6.3, 6.5, 6.7, 6.8, 6.9 and Spline drive.

• Interchangeable tips to fit 8 sizes of spoke nipples.
• ( 5.6 / 5.8 / 6.0 / 6.2 / 6.4 / 6.6 / 6.8 / 7.0 mm )
• Main shaft is CNC precision machined from 7075A aluminum and designed for optimum grip.
• Tips are made of heat treated steel for strength.

Convenient professional grade spoke wrench, a great addition to any tool pouch.

• Knurled nonslip aluminum handle
• Includes 6.8mm tip
• Quick release ball detent tips allows for quick changes to other optional sizes

Recommended for use with Warp 9 wheels. Please measure nipple size to ensure proper fit.

Precision cut from heavy gauge material.

Extremely durable design.

Push/Pull design for hard to reach places.

Soft but durable PVC coated handle.

ULTIMATE SPROCKET WRENCH KIT

• 12” long wrench gives you more torque to get those thread locked sprocket bolts off easily
• Double ended 12mm & 13mm to fit all modern motocross, Enduro and dual sport bikes
• Dog leg wrench design allows wrench to easily clear rim edge and wide tires
• 8mm allen fits most Japanese bikes 8” long for extra leverage
• Torx T45 fits late model KTM and Husqvarna bikes, 8” long for extra leverage
• Vinyl coated handles to protect rim edge and give a non slip grip
• Makes routine sprocket bolt maintenance a quick and easy job

Use simple leverage to easily lift your dirt bike up on to a flat platform.

The platform angle adjusts easily so either wheel can be off the ground quickly and safely for work or cleaning. These adjustments can be made with the bike on the stand.

Folds up for easy storage and transport.

Adjustable legs for use on any terrain and allows for even lift height for any dirt bike.

Closeout item, as is, no warranty.

Thread Chasers are designed to clean and re-cut damaged aluminum threads.

This kit contains the two sizes most common on metric motorcycles, M6x1.0 and M8x1.25.

Thread Chasers also remove dirt and metal shavings that become captured in thread grooves.

Uses 8mm or 10mm hex sockets, a Must for all tool kits.

The Giant Loop Tow Strap is a multi-functional tool that helps get you or your riding friends out of sticky situations.

This Cordura® Ballistic tow strap, designed with sewn loops on each end, can be girth hitched around a tree, bumper, rock, etc.; or used with footpeg-to-footpeg or other motorcycle (and snowmobile, ATV, snow bike) towing techniques. Constructed in the USA from ultra-durable custom woven Cordura® Ballistic webbing, which folds up into a compact integrated cover made with 22 oz. vinyl-coated polyester, or what they like to call “truckers tarp.”

Doubles as a quick deploying, super-strong ridge line for pitching a shelter tarp.

• DIMENSIONS: Measures 14’-9″ L (450 cm), with 6″ (15 cm) loops sewn into each end. 10″ L x 2″ W x 2″ D (25 cm L x 5 cm W x 5 cm D) (packed)
• WEIGHT: 5 oz. (141 g.)

Color may vary based on manufacturer availability, quality will not be compromised.

A compact and lightweight solution to eliminate the SNAP for a safer tow. If you have ever towed a motorcycle you are familiar with the snap that comes with a traditional tow strap. GCAG made the Dynatow with a section that gives 32 inches of stretch so both riders have an easier tow.

The 26 foot total length gives you enough room to maneuver around obstacles and allows the freedom to choose better lines if you are towing in the gnar.

You can also use this as a recovery strap. You can girth hitch the loop end to the bike and throw the other end to a friend to pull. The dynamic properties of the Dynatow will help assist the pull. All of this functionality fits in a flat pouch about the size of sandwich and only weighs 12.8 oz. Throw it in your bag and be prepared.

Specifications:

• 1" Nylon Webbing - UV resistant and heavy duty.
• Tough Tensioners - The elastics are woven inside tubular nylon webbing for protection and strength.
• Hi-Viz Color - The bright green color will make this easy to see.
• Sewn Loop - The towing rider can choose to use a loop around the peg or wrap it. The loop also gives options to girth hitch if needed.
• 1000D Cordura Storage Pouch- protects the strap against abrasion while stored and keeps it compact.
• Multi Use - All good adventure gear is multi-use. Here's a few ideas.
  • Ridge line for a tarp.
  • Clothes line while camping.
  • Recovery strap for a friend to pull on.
• Compact and Lightweight
  • Dimensions - 8 in x 6 in x 1 in
  • Weight - 12.8 oz
• 1,000 LB Working Load - They made it strong just like all of their products.

Please consider the following before use: Practice before you need to use this product. Always inspect your Dynatow strap before use and NEVER use a worn strap. They recommend a proper training class to learn safe methods for towing a motorcycle.

Simplify self recovery with this quick deploy Z-Drag kit. It can sap your energy trying to get your bike unstuck. It can also fall in a way that makes it very difficult to pick up. The Z-Drag is a common rig to give you a mechanical advantage for reduced pull. The combination of roller cams provides a 4:1 pulling ratio for self recovery and a 5:1 ratio when you have help. A laminated instruction card is included in the bag.

3.5MM X 20FT

Made from Tough but lightweight 12 Strand SPECTRA / UHMWPE

2200LBS Break Strength

Double Looped Ends

Each Looped end is Covered in a Kevlar Sheath to protect the rope from abrasion

A must for getting your wheels straight, concentric and true. For use with a truing and balancing stand.

Dial Indicator Features:

• Revolution counter.
• Graduation: .001"
• .100" revolution
• Dial reading: 0-100

Magnetic Base Features:

• 130 lbs. of pull.
• With fine adjust.
• Base: 2-5/8" x 2"
• Overall Height: 9"
• Permanent magnetic type ON/OFF switch makes it easy to rest on iron or steel.

Kit Includes:

• Dial indicator.
• Magnetic base with fine adjust.
• Supplied in plastic storage case.

Always wanted to build or true your own wheels? Maybe just be able to balance your wheels after changing tires. This stand is perfect for both of those tasks.

• Features a bubble level to balance wheels correctly the first time
• Steel plate construction for durability and stability
• Comes with shaft, cones and spacers to fit just about any wheel

• 26 straight blades
• SAE and metric markings
• Check for clearance on valves, ignition points etc.
• Includes 26 blades varying in thickness from .0015"/.038 mm to .025"/.635 mm

Made from precision-drawn, chrome-vanadium tool steel, the BikeMaster® 9-Piece Ball End Hex Wrench Set and Holder features a bead-blasted surface for a better grip and a corrosion-resistant coating. They have a ball end, allowing an angled reach and access to obscured bolts. It comes with a durable holder and manufacturer's lifetime warranty.

Comes with sizes 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm and 10mm