Africa Twin (CRF1000L): Fuel and Intake

*NEW OFFERING

The Dynojet Auto Tune kit is an "add on" accessory that can be used with any of our Power Commander V’s. It connects to the PCV with a single cable and requires only a ground and +12 volt connection to be made to install. If your exhaust does not already have one, a "weld in" O2 sensor bung is included.

Once installed, the Auto Tune kit monitors the fuel mixture (by installing the included Wide Band O2 sensor in the exhaust). It then sends this information to the Power Commander V and automatically corrects it while you ride. Each map that we offer has preset Air/Fuel ratio values included that we find to be the best overall settings. This lets you simply plug in the unit and let it do the work.

POD-300 Digital Display

Simply connect the included CAN cable and you’re ready to go; there’s no need to tap power or deal with other messy connections.

• Real time fuel adjustments
• Display channels real-time: RPM, TP, map position (when using map switch), duty cycle, fuel change, speed, pressure, ignition change & wideband air/fuel ratio- (w/WB2 or AutoTune connected)
• Weather resistant for use in all conditions
• Log channels saved to internal memory and can be viewed / analyzed with Dynojet’s PowerCore Software
• High contrast display, viewable in direct sunlight
• 3 Programmable light alarms

Two-position map-switching is capable with this Single Pole, Single Throw switch. You can toggle between two different fuel maps quickly and easily.

For Use with the DynoJet Power Commander V

The EJK evolved out of the need to address the ever-increasing complexity of factory fuel injection. For the newcomer to the market or professionals wanting an easier method for tuning fuel injection, the EJK is a customizable solution for the rider that wants to take control of their tuning needs.

This unit is a piggy-back EFI controller because it does not replace the stock ECU, but rather monitors the signals to the injectors and makes fuel adjustments based on the mode settings. The GEN 3 has a push button interface allowing access up to 6 different modes to allow for quick fine tuning by the end user without needing a computer.

Key Features:

• No computer or dyno needed!
• Plug and play, simple to install, base settings preset
• Unique load based technology
• Full range tunability available
• Does NOT interfere with stock ECU operation
• Simple push button adjustment interface
• Water-resistant 
• 2-Year warranty
• Compact size - 2.2" H x 3.4" W x 0.5" D

Genuine Keihin spring, washer, and oring for the fuel screw of FCR and FCR MX carbs.

Just the parts…
Fuel screw spring, washer, o-ring (fuel screw not included)

Original equipment replacement 'in-tank' fuel filter.

Traveling where fuel quality will be questionable? Carry a spare fuel filter.

The small size and right angle hose barbs make this filter easier to fit into the small space between your fuel petcock and carburetor. Filter body is only 7/8" diameter. Straight filter is 2" long, 90 degree filter is only 1-5/8" long.

This filter is meant for 5/16" fuel lines. Only 1/2" thick it is small enough to fit just about anywhere.

Two layers of foam, catch and retain nearly any contamination you will encounter.

The adhesive that holds the two materials together withstands repeated cleanings even with harsh solvents or gasoline.

These filters are slightly smaller than stock to increase air space around the filter, improving circulation and air flow. A thick, flat breathable foam gasket forms a grease free sealing ring that ensures maximum contact with your airbox.

This kit includes 2 fire resistant pre-oiled air filters and 2 plastic filter frames.

Sold in 6 packs

• Compatible with many air filter boxes. Easy to install by drilling 1’’ holes in airbox housing and snap fitting vents in.
• May be cleaned and re-oiled
• More air flow allows you to add more fuel to your intake mixture, increasing performance.
• 1" Diameter

Not legal for use on pollution controlled vehicles in the state of California.