Replace your worn clutch plates and springs to reduce fade and slip.
Complete set of friction plates, HD springs and steel separator plates prevent premature driven plate wear, oil muddying and loss of stack height.
Built with swaged aluminum carriers that spread the load on the clutch basket and prevent clutch basket "dogging".
Anti-swell, alloy impregnated heavy-duty, cork-based facings for smooth clutch take-up, and allows engagement modulation, unlike paper clutches which tend to snatch.
All in one package.
We suggest adding a set of HotCams camshafts and a new clutch kit for the best results.
You will need to tune your EFI with something like the Power Commander V to get the most out of your Big Bore kit.
This will not fit the DRZ400 kick start models. Nothing is available for the kick start models.
This is a completely rebuildable stroker crank (3mm additional stroke) turns your mild mannered 250cc motor into a 263cc trail shredding monster! OK, maybe not, but sure makes it a fun machine.
Want the COMPLETE package? Order a Big-Bore kit to go with your stroker! That will give you a 308cc ripper! That is 24% larger than the stock 250. This package includes the Athena Big Bore Kit plus the 3mm Hot Rods Stroker Crank with new Genuine Yamaha crank bearings.
You will need to tune your EFI with something like the Power Commander V to get the most out of your Stroker kit.
For stock bore Hot Rods highly recommends you use the Vertex Stroker Piston Kit.
A high quality cam chain from the folks at Wiseco. New cams, big bore kit, high-mileage motor, you might want to think about a new cam chain. Direct replacement for stock unit.
Stage 1: Excellent mid-range and top-end power increase. Uses stock valve springs and rockers.
Fitment Specs: Exhaust Lift: 8.7; Exhaust Duration at 1.00mm: 236°; Intake Lift: 9; Intake Duration at 1.00mm: 236°
Here's another item you might want to replace when you are changing out your front sprocket. Because of it's big back tire, the chain is further away from the center of the engine than most bikes. The engineers at Yamaha decided they had better support the end of the countershaft since it is cantilevered out there so far. They also figured they had better feed some oil out there as well. These Countershaft Seals keep that oil where it belongs, lubricating the countershaft outer support.
Leaking Base Gasket? Replacing your worn Rings? Here are the gaskets you need to put your TW200 top end back together after a tear down. Includes: Head Gasket, Base Gasket, Stud Gasket, Head Side Cover O-Ring, two Valve Cover O-Rings, Base O-Ring, Stud O-Ring, Rocker Shaft O-Ring, two Cam Chain Tensioner O-Rings, Intake Manifold O-Ring, two Valve Stem Seals, and Exhaust Gasket.
Changing your countershaft sprocket? Here is the gasket you need for the left hand side case cover of your TW200. This is the same side of the engine as your gear shift lever and chain.
High quality aftermarket paper gasket.
Fresh O-rings to ensure your XRL stays oil-tight and leak free. The Valve Cover Kit includes 4 new valve cover O-rings.
Fresh O-rings to ensure your XRL stays oil-tight and leak free. The Oil Change O-Ring kit includes a filter cover O-ring and a filler plug O-ring.
A high quality top end gasket set for the XR650L
Works Connection Billet Plugs for your left side case. These blue plugs includes both the timing mark plug and the crankshaft access plug.
Keep yourself COOL with a set of Moto Hoses. Moto Hoses are what you need to handle the heat that your bike is putting out whether you're pushing it to the limit or just stuck in slow city traffic.
Each Kit Contains:
10mm diameter - Includes three valve shims of each size from 1.85 to 3.20 in .05 mm increments. 84 shims in total, 83 cents per shim!
Direct replacement for old or broken stock spark plug caps.
Spark plug caps contain a resistor that can burn out with age. Fresh caps ensure your motor gets a strong spark.
Complete set of 'Adventure' wheels. These are the same rim sizes as used by the BMW GS and other big adventure bikes. The 19" front and wide 17" rear will give you great twisty road handling on the pavement while still being dual-sport friendly.
We start with silver Excel or Sun rims, OEM hubs and Buchanan's heavy gauge stainless steel spokes. Rims and spokes are precision machined for a perfect match to your bike.
Our pro shop then laces and trues your wheels to perfection, giving you the highest quality set of custom wheels available.
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
This nice piece replaces your plastic sprocket cover and protects your engine case from a chain derailment or failure. The 3/16" (5mm) thick steel plate is adjustable to accommodate 14, 15 and 16 tooth sprockets. Includes mounting hardware.
By simply replacing a motorcycle's stock shock linkage with with a longer, stronger and lighter DeVol Lowering Linkage, a bike's seat height will be dramatically lower to help give those riders with shorter inseams a more confident and enjoyable ride.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Kouba lowering link will lower the rear 1.75". Comes with bearings and seals installed for a quick and easy installation. Instructions included. WILL NOT FIT THE CRF250L RALLY OR CRF300L.
Billet aluminum lowering links. Lowers the rear suspension.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Precision tolerances – The tightest in the industry. Ultra-lightweight, for reduced unsprung mass. Straight rate springs will give better control.
Sold in pairs.
Tired of your mushy front suspension? ProCycle now offers heavy duty fork springs for the TW200!
Includes material for spacers.
Stock Spring Rate is .50 kg/mm. The .60 kg/mm springs are 20% stiffer than stock while the .70 kg/mm is 40% stiffer than stock.
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.
OEM spring rate is .46kg. We offer stiffer spring rates from -5% to 10% for riders who wish to carry luggage or just prefer stiffer suspension.
5% Less than stock
Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.
Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward.
Simple to install and completely tunable for all conditions and rider preferences.
Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.
Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward.
Simple to install and completely tunable for all conditions and rider preferences.
This 'Bling Ring' replaces the two stock preload/lock rings. The ring is CNC machined aluminum with the additional thickness to provide superior support on the shock body.
The added needle bearing thrust washer will make preload adjustments much easier. The ring then spins much easier against the spring making adjustments quite a bit easier.
To install the Bling Ring on a Cogent or Race Tech Shock Shaft Assemblies, it must either be disassembled or have the lower clevis removed.
Cogent Dynamics takes a stock DR650 shock, tears it down, cleans it up, adds a hard ceramic coating, then rebuilds it with a completely new custom shim stack that gives you excellent rear wheel control.
This custom Cogent valve stack makes this shock behave much like the Cogent Shock Shaft without the rebound adjustment capability. Providing a greatly improved suspension feel over stock at an affordable price.
Spring not included, sold separate.
Recommended spring rates:
This shock includes the Bling Ring preload adjusting ring AND the Thrust Bearing! This replaces the two stock preload/lock rings. This ring is CNC machined aluminum with the additional thickness to provide superior support on the shock body.
This option is ideal for those who desire the least amount of down time to install this suspension upgrade.
This kit includes a core charge that allows us to ship your new shock before we receive your stock shock core in 'good' condition. More details regarding core exchange linked below.
Lighter and stiffer than stock, these high quality straight rate springs are custom made specifically for the TW200. No adapter is needed! A proper rear spring will give a smoother more controlled ride. No more bottoming and better traction and confidence off-road.
If you (with all your gear on) weigh up to 220 lbs, you want the 15 kg/mm spring. 225 lbs and up will want the 19 kg/mm spring.
Replace those worn-out and high-priced stock KTM swingarm bearings with this swing arm bearing kit from Moose Racing.
Repair kit includes all the bearings, seals, shafts and spacers required for a complete rebuild.
Constructed from OEM-quality components at a fraction of the cost.
Complete Swingarm Bearing kit to replace the bearings and seals in the WR swingarm pivot.
| Description | QTY per Kit |
|---|---|
| Needle Bearing | 4 |
| Needle Bearing Shaft | 2 |
| Seal | 4 |
Complete kit to replace the bearings and seals in the WR shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Seal | 8 |
| Needle Bearing Shaft | 6 |
| Needle Bearing | 5 |
Complete high quality kit to replace the bearings and seals in the swingarm pivot.
Complete high quality kit to replace the bearings and seals in the KLX shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Washer | 4 |
| Seal | 8 |
| Needle Bearing Shaft | 4 |
| Needle Bearing | 7 |
Complete high quality kit to replace the bearing and seals in the DRZ400 swingarm pivot.
Complete high quality kit to replace the bearing and seals in the DRZ400 shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Seal | 8 |
| Needle Bearing Shaft | 4 |
| Needle Bearing | 7 |
The little WRs have decent shocks but it can surely be improved with a Rear Shock Gold Valve from Race Tech. This will improve the damping in both directions and make the clickers more responsive to adjustments.
The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.
Top suspension performance requires firm bottoming resistance with plushness at the same time. Even the best suspension tuners can only make the stock valving design work so well. The Gold Valve Shock Suspension System is a proven bolt-on shock valving system that improves control, traction, performance and bottoming resistance.
For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.
The stock sprocket retainer will rub the chain when it is used with 13 and 14 tooth sprockets.
We have our own sprocket retainer laser cut from 13 gauge stainless steel. This retainer works with all 3-hole 13T, 14T, 15T and 16T DR650 countershaft sprockets.
This kit will replace your stock sprocket bolts, nuts and keepers with new hardware.
Many aftermarket sprockets are thinner where they bolt to the wheel and the threads on the stock bolts do not allow these sprockets to be tightened down all the way. These grade 10.9 bolts will alleviate that problem. They are the same length as the stock ones, but the threaded area is longer allowing stock sprockets or aftermarket sprockets to be securely tightened down.
The bolt keepers are genuine Yamaha replacement parts to ensure an accurate fit. It's a perfect upgrade if your keepers have been removed too many times.
A CNC machined chain guide for the DR. Stronger than the wimpy stock unit and can easily accommodate the stock 525 chain as well as a 46 tooth rear sprocket (by moving the lower rub block to the forward position). The rub blocks are also a higher grade, longer lasting material.
More range at a great price. Choose the 2.7 gallon tank for the KLX250S in Black, Green, Natural or White.
This tank will NOT fit the 2009-2015 models.
More range at a great price. Choose the 2.6 gallon tank for the newer KLX250S in Black, Green, Natural or White.
This tank will NOT fit the 2006-2008 models.
Includes all necessary o-rings and diaphragms
This chain lube comes in a squeeze-tube bottle with an integrated brush nozzle. It makes applying chain lube easy and less messy than spray on lubes.
The Warp 9 shift lever is black anodized and the Warp 9 logo is laser etched into the finish. Comes with a black anodized knurled aluminum tip that folds and returns via a stainless-steel return spring. Includes the pinch bolt as well.
This bracket mounts between the frame and your right footpeg bracket (works with both stock and low mounts) and allows you to adjust the slop out of the stock system.
Places the pedal in the ultimate location for immediate brake activation and eliminates unwanted pedal motion.
Kit includes plate, adjuster bolt with lock nut and instructions.
Centerstands may impede the proper operation of this bracket.
Better throttle response. More power over a much wider range.
Kit includes pre-jetted genuine Mikuni TM36 Pumper carb and push/pull throttle cables. Everything is included to mount this carb to your bike. Well suited for stock to mildly modified motors.
A set of six high quality grade 10 sprocket bolts with lock nuts. Thread-lock compound has already been applied for extra security.
These bolts are flat head style, requiring a countersunk hole in the sprocket.
Simple, quick installation of this 1 pound rack made from rugged 1/8" 5052 Aluminum. A rigid 4-point mounting system, but still sleek and low allowing for seat removal with no hassles.
Features:
Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.
The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary hardware is included. 10.5"Wx11.5"L
Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets.
An optional add on to your ProCycle Top Rack to relocate your rear turn signals with ease.
This gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. Get a fresh one now to ease installation of your new performance muffler.
This gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
The headpipe gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head, thereby making them a single use part. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
The muffler joint gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers (Q4 or PowerCore 4) do not require a joint gasket but the all other aftermarket mufflers as well as the stock muffler do require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.
The science behind the MegaBomb header may be FMF's greatest engineering accomplishment to date. You can bolt on a MegaBomb with an existing FMF Racing slip on for as much as a 3hp boost, plus the MegaBomb actually reduces noises levels by as much as 1.5dB. The MegaBomb technology is evolved to produce more low end to mid range gains as well as broadening out the mid to top end power gains over stock. MegaBomb is the next level technology you can have today.
For FMF mufflers only
The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels.
Constructed from 304 stainless steel and breathes much better than the stock unit. Handmade in the USA with a 1 Year Limited Manufacturers Warranty.
The V2 Series Slip-On muffler features an aluminum body, TIG welded components, stainless steel inlet tube and a great new look. This Lightweight Slip-On weighs approximately 5.5 lbs.
The DG Performance systems offer increased throttle response, power and torque. Standard sound level is approximately 98 db. Equipped with a US Forestry approved spark arrestor.
No repacking required! The Leo Vince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed a 84dB sound level using the USFS J1287 testing procedure. 84dB is louder than stock but significantly quieter than any other aftermarket muffler. It includes a certified Spark-Arrestor.
This muffler works on OEM header only!
Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Unit is pounds lighter than stock and gives gains in horsepower and torque throughout the RPM range. All of that in a package handmade in the USA with a 1 Year Limited Manufacturers Warranty.
This is a new Diaphragm Set for your 1987-2000 TK carburetor. If yours has cracked or ripped, here is a replacement.
Repair kit comes with everything you need to get your carb back in shape.
Top quality brass screw with molded knob for easy adjustments.
Not for the stock DR650 carburetor Fits FCR-MX conversions Only.
The Power Commander 6 fuel injection tuning device allows you to optimize your fuel and timing curve (where applicable) giving you the confidence to roam freely. With fine tune adjustability and multiple inputs, the Power Commander 6 will keep your vehicle running at its full potential letting you concentrate on the journey ahead.
Featuring a plug-and-play setup, Power Commander 6 can be installed discreetly underneath your seat, cowl, dash or other location ensuring your ride looks as good as it runs. Removing the device reverts your vehicle completely back to stock. With the ability to store and switch between two maps on-the-fly (via the map switch accessory) and connect to various Power Commander accessories such as the Autotune, Quickshifter or POD-300, the Power Commander 6 gives you features and functions that provide you with the ultimate ride.
All PC6 models have an end-user adjustment of +/-15 in the FUEL table and +/- 8 in the timing table (if applicable). This adjustment is on top of the values that are in the BASE map loaded to the device. This BASE map can be any of the available maps from the Dynojet website, or those you may have received from a third party.
Genuine Honda replacement air filter.
Yamaha uses this seal material in many places on several motorcycles. It is like weatherstripping and is used to seal up the edges in the TW200 air-box. It seals up the air-box so that water and grime can't enter the air-box from the side. Ensures that air entering the box comes from up under the seat.
Hiflofiltro air filters are manufactured to fit the factory air box and are a direct replacement for original equipment filters.
Top quality powerflow filtering media, developed for modern high performance engines.
We all love our TWs, but the stock jetting leaves much to be desired! Here is a Jet Kit for your stock TK carburetor to improve your throttle response. Included in the Kit are a wide range of main jets to cover any setup, one Pilot Jet, one Jet Needle, and five Needle Shims. If you have added an exhaust system or ride at higher elevations, this is a great way to tune your TW for your needs.
Quality air cutoff valve replacement kit contains parts necessary for a complete rebuild.
Since Kawasaki brought back the popular little KLX250 with updated fuel injection, Yoshimura brought back an updated RS-2 slip-on that now incorporates an o2 sensor that accommodates the new fuel injection technology on the KLX. All of that with added power, torque and that distinct Yoshimura exhaust note.
Entire unit is proudly made in the good old US of A to boot!
The product that you are purchasing is designed and intended for closed course competition use only and is labeled as such, i.e. Yoshimura "RACE SERIES." Yoshimura RACE SERIES products are neither designed nor intended for use on PUBLIC ROADS or LAND. Such use is prohibited by Federal and State regulations.
Use this installation tool from Cogent to be sure that your Cogent Drop-in Dynamic Cartridges are installed correctly. A strong magnet in the end holds the cartridge firmly while you lower it into your fork leg. Then slide the spring over the tool until it holds the DDC down, then gently remove the tool. That simple. Never again question if it is properly seated on the damper rod.
Works equally well for removal when you need to change your fork oil. Also works great with Race Tech Emulators.
New wider seat to help keep comfortable on that long commute or dual-sport ride. The added width and foam density will help keep the seat from being an item to stop you from going on that ride or enjoying the bike.
Each kit contains detailed instructions for easy "Do It Yourself" installation. This provides the highest level of quality & comfort at an affordable price.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
The Foam and Cover Kit is only for the OEM pan. It DOES NOT include the pan.
Only Available in Tall; All Carbon Fiber
| Width: | 9.5" (241mm) |
| Height | 1" (25mm) TALLER than the stock seat |
Recover that shredded or uniquely colored stock seat cover with this OEM black cover. This includes only the cover material (grab strap is no longer available). Designed to fit over your stock seat pan and foam.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail / stop light function. 3 white LED's are used for license plate illumination.
Included is a set of turn signal brackets that bolt to the mount, but these are designed for a smaller LED type signal with a mounting stud of just 8mm. Or consider the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!
NOTE: LED's must be installed on a 12 V DC system!
Clean up the backside of your TW200 and upgrade to a brighter, safer LED taillight in one go!
The Tidy Taillight Kit includes a durable, high-quality steel mounting bracket that mounts under your rear fending using the existing bolts. The bracket also has slots to mount your license plate.
The included LED taillight helps make your TW more noticeable to other drivers at night, and the super-bright LED brake lights activate more quickly than stock incandescent bulbs when you get on the brakes, giving drivers behind you more reaction time. The taillight unit also features white LEDs on the underside to light up your license plate and keep you legal.
The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail/stop light function. 3 white LED's are used for license plate illumination. Included is a set of turn signal brackets that bolt to the mount. These are designed for a small signal with a 8mm mounting stud.
Here is the little switch that mounts inside your brake or clutch lever perch and controls the brake light or clutch safety circuit. This switch often gets damaged in an unplanned dismount (aka: crash) or the plastic simply cracks from age. When this happens, you can find yourself chasing a short circuit that keeps blowing your fuse every time the brakes are applied. If this has happened to your TW, here's the fix!
The 12oclock Labs EXUP Emulator is used in place of the stock exhaust servo motor when you replace the stock exhaust with an aftermarket exhaust system. The microprocessor controlled EXUP, emulates the exact characteristics of the stock exhaust servo motor and its motor delay sweeps, keeping the ECU from displaying the dreaded check engine light. Weight is less than 1/2 an ounce and it is a direct plug and play replacement.
If you are looking to swap out your stock CDI box, the Big Gun Rev Box is an affordable alternative to highly-priced OEM replacement boxes. It increases the overall RPM limit over the stock box and advances the timing curve and is a direct plug-in replacement.
You must cut the green wire on the 8-prong plug going into CDI box.
Shorai batteries deliver more energy faster, with less weight and with less wear on the battery per start cycle than any other brand or technology available on the market today.
Specifications:
Weight (lbs): 2.30 lbs
Weight (kg): 1.04 kg
Cold Cranking Amps: 270
A/HR: 18
Polarity: [+ -]
All the parts you need to freshen up your rear brake master cylinder. New piston, seals, return spring, boot and snap ring.
GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
A set of front and rear brake rotor bolts.
Class 10.9 steel rotor bolts provide excellent sheer strength and include medium-strength threadlock patches to securely fasten your rotor.
This kit is for those of you looking for a bit more leg and arm room in the DR cockpit. Included are ProCycle Low Foot Pegs and our oversize bars.
