This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.
This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.
Put fresh O-rings on your KLR when you do your next oil change. Here you have new ones for the Oil Filler and the Oil Filter Housing Cover.
Changing your countershaft sprocket? Here is the gasket you need for the left hand side case cover of your TW200. This is the same side of the engine as your gear shift lever and chain.
DRC is one of the leading manufacturers of silicone hose kits for motorcycles.
Higher pressure in the cooling system, raises the coolant boiling point and increases protection from coolant loss due to overheating.
23 PSI - 1.6 Bar.
Add a backup kick start system to your electric start DRZ400. Complete with everything you need to add the kick starter to your bike.
This kit will fit all DRZ400s but the manual decompression lever can only be installed on the 2006 to Current DRZ400 E models.
The complete Thermo Control package - Our in-house designed Thermostat Bypass kit, a set of Custom Silicone Hoses and a Hi-Pressure Radiator Cap. All combined to help your KLR cooling system be at the top of its game. The Thermostat Bypass kit includes a thermostat with a higher temperature rating that will keep the motor more in its happy spot.
The Silicone hoses are stronger than the stock rubber units and will better resist cracking and leaking.
The starter bushing in the DR650 leads a tough life. Exhaust heat and minimal lube from the factory take their toll. Warp 9 has a high quality solution - a billet starter cover with a sealed ball bearing.
Outer Clutch Cover O-Ring, Inner Clutch Cover Gasket, Stator Cover Gasket.
Sold individually, not as a kit
The EBC DRC kit is the best way to reset your bike’s clutch to the exact as new standard sizing. Replacing just the plates can work but new clutch springs are always better and springs get tired and can cause slippage plus the separator steel plates from EBC are pin-planished, forming tiny indents in the steel which improves the spread of oil around the clutch surfaces.
Includes:
Billet plugs for your left side case.
Includes both the timing mark plug and the crankshaft access plug.
The 244 Series Dual Sport street and trail tires were designed to be equally at home on dirt or pavement. Great value.
The Shinko 244 is a very popular tube-type upgrade for the front tire on the TW200 or the VanVan. DOT approval coupled with excellent performance both on and off-road make this tire a winner!
The 244 Series dual purpose street and trail tire is designed to be equally at home on dirt or pavement.
Available in 5.10-18 (69P load / speed rating) and 4.60-18 (69S load / speed rating).
Motoz Tractionator Desert H/T series of tires are renowned for great traction and long wear life. These tires are designed to handle hard terrain, fast and rocky trails as well as gravel roads and desert hard pack. Tricky off-cambers, ruts and hard braking at extreme lean angles are no problem for this DOT approved tire.
Note: Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.
This kit fits all Nomadic tubular type racks. (All flat stock racks are already RotoPax compatible)
The second image shows the kit, which includes all the hardware and instructions required. The lower image is just an example of what the eXpander looks like mounted to one of their racks.
You may purchase just the rack or you can order the Rack with the RotoPax Mount. If you really want it all, you can order the Rack, Mount and a Fuel or Water Container.
DRZ400 rack is available in both a Utility and Sport version. The Sport version is 9" x 9" and the Utility is a full 2" longer for added storage space. Both of the S/SM racks have tabs so you can bolt the stock tool bag on.
Please select the rack for your specific model as the differences are significant
CNC machined from 5mm aluminum 5083 plate with lots of slots to attach your Rok Straps (or other straps). This gives a considerably wider deck than the standard B&B Rack. Attaches directly to the B&B rack with four screws that are included. Available in either polished aluminum or a black polymer coating.
These plates are pre-drilled and countersunk from the bottom making installation of a RotoPax mount quick and easy.
Some older carry racks will not have predrilled holes in them to mount luggage plate in which it will require you to drill yourself (select pre2018 version)
This is for the add -on Top Plate only.
Fits B&B Luggage Rack purchased AFTER 2018
Hand built aluminum luggage rack from the B&B Off Road Engineering folks down under. This unit really is a beauty to look at and extremely rugged, made from 4mm 5083 aluminum plate! Tie down whatever you need with confidence. Whether it's your books to get to school or a bag to get across the country, no worries mate. Available in either bare polished aluminum or with a black polymer coating.
While plenty rugged to use as grab handles, you can keep your stock handles if you so desire. All necessary stainless clamps and bolts are provided.
If you want a wider platform for support, consider adding the luggage plate to this rack.
Bike must have the DR250 Taillight installed to work with this rack.It will not work with the stock USA taillight.
These flat tie down 'stretch' straps are designed specifically for motorcycles, ATVs and snowmobiles. Carry anything on your motorcycle securely and without scratches with these flat - no hook - tie down straps.
ROK Straps are a two-piece strap with a quick-release buckle in the middle and loops on each end. One end of the strap is a heavy duty nylon, the other has a strong stretchable section. Instead of hooks that can slip or come undone, ROK Straps have a loop sewn in each end. you pass the buckle around your frame, rack or other secure point and then back through the loop in the end making for a very secure mount. With each end secured, connect the buckle in the middle and simply tug the slack end of the strap until your load is firmly held in place.
The Motorcycle Adjustable Strap is 1 inch wide and adjusts in length from 18 to 60 inches.
Rated to carry 100 lb (200 lb burst strength)
Designed specifically for motorcycle and ATV use.
Here is the best value in Dual Sport luggage, the Nelson Rigg Sierra Dry Saddle Bags.
Fly Racing small tank bag has a 7.5 liter capacity, with touch screen compatible top map/device pocket that holds most GPS and cell phones.
Combined strap and magnet mounting system, reflective piping and logos, and convenient carry handle.
Micro fleece lined exterior pocket, and includes rain cover. Measures: 13"L x 10"W x 5"H
Lite:
The Go Cruise cruise control mounts over the throttle grip and rests on the brake lever to hold your throttle open, allowing you to stretch and rest your hand on long rides. Installs and removes in seconds with no tools. You can roll off the throttle manually to disengage the Go Cruise.
NOTE: These will not work with Warp 9 levers
High quality steel rear sprockets from 39 to 53 teeth.
Sprocket color may differ depending on size.
Quality steel front sprockets. Choose 525 or 520. Also available 'Wide Boss' JTF438 520 sprockets.
All 520 sprockets require a new retainer plate, please add on if purchasing this size.
Quality steel rear sprockets. Choose 525 or 520. 41T to 50T
48 and 50 sprockets require removal or modification of your lower chain guide.
Chain Size Recommendations:
*Actual sprocket color may differ from image shown.
We have 44, 45, 46 and 47 tooth rear sprockets available for the SV. Select the sprocket size from the dropdown.
JT Sprockets is the world's leading manufacturer of aftermarket sprockets, constantly raising the industry's standards for quality and service. JT Sprockets are the only sprocket manufacturer using the ultra-durable high carbon C49 steel for rear sprockets.
These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Individual 14T, 15T or 16T front sprockets.
JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.
Quality rear steel sprockets.
These masterlinks fit the original OEM Suzuki chain. The original chain is marked DID 525 V8. Choose from Clip Type or Rivet Type.
Quality steel sprockets and 525 O-Ring chain. 525 chains come in 120 link length and will have to be cut down to fit. They also come with rivet type master links. Clip type master links are available below. Single sprockets and chains are also available below.
Get better range from your XR650L by adding a Clarke 4.7 gallon fuel tank. Cannot use stock shrouds.
Available in Natural, White, Black, and Red. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap, uses stock petcock.
More range at a great price.
The 3.6 gallon tank is for the off-road DRZ400 and DRZ400E.
The 3.9 gallon tank for the dual-sport DRZ400S. The 3.9 gal tank also fits the ES and SM models.
Both tanks are available in a selection of colors.
NOTE: Clarke tanks do not come with a vent hose or vent cap.
Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for the dunes or the race track! These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of the big Acerbis or Clarke tank? The 4.0 gallon tank from IMS might be just right. Includes cap, uses stock petcock.
A replacement Clarke Gas Cap that fits most Clarke Gas tanks. Comes with rubber gasket.
TechSpec’s Motorcycle Tank Grips were developed to improve body, bike control and increase riders comfort. Gripping your motorcycle between your knees or thighs improves overall control of your ride by better securing your body weight and seat position under the forces of braking, cornering and acceleration while also relieving pressure from your wrists, elbows, shoulders and lower back giving you increased control and a more comfortable, safer ride. Snake Skin is a thin, .125” medium durometer “rubber” material that offers a secure, comfortable grip, durable protection and a clean stock look.
This universal precut kit includes left and right tank grips. (8" X 3") Triangle
A popular upgrade from the stock vacuum operated fuel valve. Manually operated. Must be shut off any time the bike is parked for more than a few hours. Fits stock tank or aftermarket tank and has both main and reserve. Fully rebuildable.
Motion Pro T-6 Combo Lever has a hex box wrench for your axle nut on one side and a perfectly contoured tire spoon on the other. Manaufactured from lightweight forged T-6 aluminum with a hard anodized finish. These beauties are just under 10 inches long and weigh only 3.5 oz. Available in a 12/13 combo unit and a 22, 24, 27 and 32mm hex ends.
Available in 9.5" aluminum (ideal for travel) and 16" forged steel (useful in a home shop/garage)
Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air- the number 1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow
This Kit replaces vital components in the BST40 Carburetor including new a Float, Needle Valve, Gaskets, Seals, Diaphragm, Spring and Float Bowl Screws to return the stock Mikuni BST40 Carburetor to like-new operation. As a bonus we have included Viton o-rings for the float assembly and 4 stainless steel allen screws.
Stock suspension suffers from poor compression damping and limp rebound damping. The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.
Genuine Yamaha fork seals and dust wipers.
Add a fresh set of inner and outer bushings for a complete fork restore.
The complete shock upgrade kit - a shock spring of your choice, Race Tech Gold Valve kit, detailed instructions and a bottle of quality shock oil to complete the job. Everything you need to transform your mushy stock shock into suspension that really works.
Recommended rates:
Race Tech shock springs in a wide range of spring rates to dial in your rear suspension to suit your weight (stock spring is 5.3 kg/mm). Recommended spring rates:
| Rider Weight w/gear lbs. | Spring Rate |
|---|---|
| 100 or less | 4.6 |
| 100-124 | 4.8 |
| 125-149 | 5.0 |
| 150-174 | 5.2 |
| 175-199 | 5.4 |
| 200-224 | 5.7 |
| 225-274 | 6.0 |
| 275 + | 6.3 |
DRZ400 E/S
A pair of Race Tech fork springs to dial in your front suspension to suit your weight.
Fits all DRZ400 models with conventional forks (not for SM)
Recommended spring rates:
| Rider Weight w/gear lbs. | Spring Rate |
|---|---|
| 90 or less | .42 |
| 90-119 | .44 (stock) |
| 120-150 | .46 |
| 150-180 | .48 |
| 180-220 | .50 |
| 220-250 | .52 |
| 250+ | .54 |
The DG RST (Reduced Sound Technology) muffler is the quietest DG muffler and is designed especially for dual-sport machines (Just 84db @ 3200 RPM). A new baffle design dissipates sound waves reducing noise output in a very efficient manner. This new design also stretches out the time between muffler repacks. Included is a Stainless Steel mid-pipe, USFS Approved Spark Arrestor and a new Aluminum end cap.
To fit tapered 28.5mm (1 1/8") handlebar.
NOTE: will not fit Renthal Twin Wall or Barkbusters VSBar.
Protect your motorcycle’s levers from damage during an impact with the solid protection offered by Barkbusters aluminum bar lever protection handguards. Constructed with solid heat treated aluminum backbones these hand protectors use a two point mounting system that provides strength to withstand plenty of force. Motorcycle handguards by Barkbusters with their full wrap design will help keep your levers operational and your ride from coming to a premature end in the event of a drop or other mishap.
Features:
Add Plastic Handguards for a complete kit.
Please Note: This aluminum bar handguard kit requires the removal of original external and internal bar weights on '19-Current models. This will leave a hollow handlebar for mounting the handguard.
Warp 9's CNC shark fin rear rotor protector. To make installation super-easy this fin bolts to a brand new CNC machined caliper bracket. Just remove your existing caliper bracket and remove the pins, install them on this new one and then put the caliper and fin back on.
Replace those worn out brake pads with quality EBC replacements.
Galfer USA produces several different brake pad compounds for all types of riding styles and uses. With over 60 years of friction material production and research, they have learned that one compound doesn’t always do the trick across the board. If you are just looking for an OEM brake pad replacement or a high performance race brake pad, they have you covered!
Set includes front and rear brake pads.
Semi-Metallic Compound
OEM replacement upgrade. Great feel, long lasting, and very little rotor wear with this durable compound. Compound applications for almost every need, including off road, street, touring, enduro, dual sport and more. Precision made in our Galfer factory in Spain.
Our most popular compound! This compound is the work horse of the Galfer family and is a great OEM upgrade for the everyday rider.
Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.
EBC rear replacement brake rotor. High friction billet steel.
Rotors are laser-cut from high-carbon content 410 stainless steel then lap cross hatch ground and heat-treated. The finished rotors are mounted on a floating black steel carrier for durability and strength.
The oversize floating pins are CNC machined stainless steel rivets with stainless wave washers to ensure they will not crush as more traditional steel pressed rivets can. Finally, high-temp paint is applied to surfaces like cooling holes and edges to provide a clean, finished look.
Includes a fresh set of brake rotor bolts.
New from Warp 9, a full floating 320mm Supermoto disc with caliper relocation bracket! These rotors have an additional hole for placement of a magnet for an electronic type speedo like the Vapor.
Includes a fresh set of brake rotor bolts.
Add bling and performance to your bike with a fresh new Warp 9 rear rotor!
Includes a fresh set of brake rotor bolts.
Warp 9 320mm Supermoto front brake rotor kit. Newly updated and stronger.
Adds serious stopping power to the DR. Included is a new rotor floating on a central mounting carrier along with a caliper relocation bracket.
Available add on options include a Galfer braided stainless steel brake line, and 12oz bottle of Bel-Ray DOT4 brake fluid.
Includes a fresh set of brake rotor bolts.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Quality parts from Acerbis. Replace those big white ones with black ones for a custom look, or you can just replace your trashed white ones with crisp clean new ones for that great stock look.
Depending on your application and preferences, more than one optional heat shield may be useful.
The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.
This shield mounts simply to the stock headlight shroud using minimal hardware to keep weight down. The Rally Windshield measures 12.5 inches tall, 11.5 inches wide at the bottom, and 8.5 inches wide at the top. Made from 1/8 inch acrylic and offered in clear or tint.
Quality replacement headlight fairing for TW200
A quality replacement speedometer cable
These tips are for the Warp 9 Shift Levers only.
These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours.
You can also order just a new pin hardware kit which comes with new pin and clip.
Warp 9 Flex 3-Finger Levers are machined Billet, anodized and hinged levers with CNC machined master cylinder interfaces.
Adjustable reach allows customization to the rider's hand size.
Double hinge design allows lever to flex out of the way in most impact situations.
Pushrod or Bearing contact styles for smooth modulation.
The Warp 9 shift lever is 7075T6 CNC arm, the Warp 9 logo is laser etched into the finish.
Includes a black folding aluminum tip and stainless spring and pivot pin for years of rust free use.
1" longer than stock
Genuine factory shop service and repair manual. This is the reference manual Yamaha dealers use in their service departments. It has all the necessary info to do any maintenance or repairs to your XT250.
ADV Sushi is a webbing reinforced velcro strap with integrated daisy loops. These are as handy as zip ties and duct tape. This is one of those products that you will use frequently if you have them with you.
A single strap was load tested at 200 pounds before it let go and a single strap held 50 pounds overnight with no issues.
Use this kit to build your custom solutions such as a fuel bottle holster, spare tube carrier, or use them to attach your bags to your Uprising Soft Rack. The possibilities are truly endless.
This Kit Includes:
Slack control has never been more convenient.
Simply slip the webbing through the slots and use the shock cord to secure the slack.
You can roll the webbing around the Web Dominator or you can bundle the webbing and secure it by snapping the shock cord around the built in anchor.
Sold in a package of 4.
A premium billet sprocket carrier from Warp 9 Racing that houses 2 bearings to help protect against the sideways twisting load that is commonly known to prematurely wear out the bearing and cush rubbers. This wear can cause extreme failure possibly damaging the hub.
Offered in anodized Silver or Black, Includes spacers and hardware.
These are designed to work with Warp 9 and OEM hubs.
Warp 9’s Pro Rim Locks are developed with Ice Track, Dirt Track and Flat Track Racers in mind!
Burnt Titanium Main Bolt
Lightweight Forged Aluminum Body
Black 7075 T6 Tower Nut and Base Washer
Base washer is machined to match each specific rim curvature for a perfect fit
About half the weight of OEM rim locks!
1.60 front – 1.8 oz
1.85 front – 2.0 oz
2.15 rear – 2.3 oz
2.50 rear – 2.7 0z
3.00 rear – 3.10 oz
These wider seat kits from Seat Concepts keep you comfortable on those long commutes or dual sport rides. The added width and improved foam density will help keep your seat from being the item to stop you from going on those big rides or enjoying the bike.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
| Width: | 9.5" (241mm) |
| Height: | Same as OEM |
These wider seats from Seat Concepts help keep you comfortable on those long commutes or dual sport rides. The added width and improved foam density help keep your seat from being the item to stop you from going on those big rides or enjoying the bike.
The Complete Seats come fully assembled on an aftermarket seat pan, and are ready to install and ride.
| Width: | 9.5" (241mm) |
| Height: | Same as OEM |
The current ProCycle logo on front, with the design on the back showing our favorite 'Pavement Ends' sign with the DR rider continuing up the road on the pegs, ready for an adventure!
High quality soft blend t-shirt perfect for everyday wear (90/10 Airlume combed and ring spun cotton/poly).
