Re-pack your silencer with this pro-quality, three layer packing system and restore lost power and sound control.
Kit includes:
The EVO R is a tried-and-true series that will save weight, add noticeable performance gains and sound tremendously better than stock.
This exhaust system is ideal for a racer on a budget that is not willing to compromise on performance! The T-4 comes complete with our stainless head pipe that works in conjunction with the silencer to produce more power from bottom to top. The use of stainless steel for the header pipe offers increased strength and should give years of trouble-free use. The silencer canister is easy to repack by removing the inlet cap screws and re-wrapping the silencer core. The T-4 meets all AMA sound restrictions.
The headpipe gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head, thereby making them a single use part. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
The muffler joint gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers (Q4 or PowerCore 4) do not require a joint gasket but the all other aftermarket mufflers as well as the stock muffler do require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.
Genuine Yamaha replacement throttle cables.
High quality replacement cables from Motion Pro.
A high quality replacement clutch cable.
These tips are for the Warp 9 Shift Levers only.
These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours.
You can also order just a new pin hardware kit which comes with new pin and clip.
These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.
These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.
Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.
OEM spring rate is 6.7kg/mm. We offer stiffer spring rates for riders who wish to carry luggage or just prefer stiffer suspension.
Race Tech shock springs require adapter collars which are included with your spring. *Spring color may vary due to specification requirement and availability.
| Shock Spring | Qty 1 |
| Spring Adapter Collar | Qty 2 |
| Spring Adapter Collar 2 | Qty 1 |
8.0 kg/mm is 24% stiffer than stock
This adapter set is required to fit an aftermarket spring to the Vstrom shock
Adapters are required for this spring
The correct spring rate for your weight will give a smoother more controlled ride. No more bottoming and better traction and confidence off-road. Kit includes required adapter collars
Stock Shock Spring 7.28 kg/mm
*Spring color may vary due to specification requirement and availability.
The Moab shock from Cogent Dynamics will change how you feel about your KLR. You may like it now, maybe even like it a lot, but you will absolutely fall in love with it once you mount up a Moab shock.
Spring duties are handled by a custom spring available in either Standard or Heavy-Duty weights. The Standard spring will be fine if you are under 250 pounds and don't ride with luggage or passengers often. Ride heavily loaded or with a passenger regularly and you will probably want the Heavy-Duty spring.
For a true comfort and performance package, we highly recommend upgrading your front suspension at the same time.
If you have '87-'07 KLR, you MUST order a new mounting bolt. Not required for 2008-2018 models.
A stiffer shock spring will help you get through the whoops or just help handle that extra baggage on the rear.
Stock spring rate is 10.5 KG/mm
*Spring color may vary due to specification requirement and availability.
This complete fork upgrade kit includes stiffer fork springs and Race Tech cartridge emulators, as well as a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
You can select from various straight rate springs to customize the package to your needs.
The complete fork upgrade kit - your choice of springs and Race Tech Gold Valves. Also includes a set of top quality fork seals and 5W fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
You can select from various straight rate springs to customize the package to your needs.
Stock Spring Rate for XR650L: 0.44 kg/mm
Lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.
DRZ400 E/S
A pair of Race Tech fork springs to dial in your front suspension to suit your weight.
Fits all DRZ400 models with conventional forks (not for SM)
Recommended spring rates:
| Rider Weight w/gear lbs. | Spring Rate |
|---|---|
| 90 or less | .42 |
| 90-119 | .44 (stock) |
| 120-150 | .46 |
| 150-180 | .48 |
| 180-220 | .50 |
| 220-250 | .52 |
| 250+ | .54 |
Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. Designed by Rick at Cogent Dynamics on his high-tech suspension dyno, then tested and endorsed by KLR owners all over, these units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the units under the springs and hit the trails.
If you weigh up to 250 pounds, select the .64 spring kit. If you are over 250 or carry lots of luggage, please select the .70 spring kit. Please call if you have any further questions.
All of these kits include DDCs, springs, fork oil and preload spacers.
A dual-rate fork spring for the early KLR650. These springs start with a .40 kg/mm winding and after approximately 20% of the stroke, stiffen up to .60 kg/mm for the remainder of the travel. A very nice improvement over the stock springs which are .40 kg/mm for the entire travel.
The complete fork upgrade kit - Straight rate springs and Race Tech Gold Valves. Also includes a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
Replace the internal components in your shock with a completely updated design with adjustments for both compression and rebound damping.
The new shaft assembly has improved valving for both compression and rebound, a thicker, stronger shaft, new seal head and bottoming bumper. Comes as a complete assembly ready to go into your shock body. You can add choice of rear spring (required).
Add a bottle of 3w Shock Oil to your order so you can start your project right away.
Complete kit to replace the bearings and seals in the XR650L shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Spherical Bearing | 1 |
| Snap Ring | 2 |
| Seal | 8 |
| Needle Bearing Shaft | 3 |
| Needle Bearing | 6 |
| Bushing | 2 |
Adjustable lowering links by PSR. Adjusts the rear suspension from stock height to 4 inches lower.
Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.
The three forces of suspension, testing procedures, even the black arts of chassis geometry: This explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.
10mm diameter - Includes three valve shims of each size from 1.85 to 3.20 in .05 mm increments. 84 shims in total, 83 cents per shim!
Complete set of engine gaskets with oil seals.
A complete set of gaskets, o-rings and oil seals. Everything you will need when doing a complete engine re-assembly.
Complete top end gasket kit for the mighty XT250
Includes all necessary top quality gaskets, and seals for engine rebuilds.
Kit includes all seals in the TW200 engine (including crank shaft seals) except valve stem seals. These are high-quality seals made in the USA.
Gasket for the engine case cover over the clutch. Doing any clutch work, you probably want to replace this gasket so you don't have any leaks when you are all done with the project.
Genuine Yamaha replacement gaskets for your side covers.
Add a backup kick start system to your electric start DRZ400. Complete with everything you need to add the kick starter to your bike.
This kit will fit all DRZ400s but the manual decompression lever can only be installed on the 2006 to Current DRZ400 E models.
This 3rd gear set is made for us by Nova Racing Transmissions in England to replace the fragile stock third gear set. These folks build complete transmissions for World Superbike teams among others, so we believe them to be highly qualified to build this set of replacement gears.
These gears are made from a high quality special alloy steel and then heat treated and superfinished. The mainshaft drive gear and the countershaft driven gear are sold only as a set.
Made from laser-cut, medical-grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area over many paper filters, catching debris down to 35 microns. The FLO filter pleat seam is welded and able to withstand up to 600 deg. F. Filter maintains consistent flow under all conditions including extreme heat, the presence of water and cold start-ups where paper filters can flow so poorly that they often cause the bypass valve to open and allow unfiltered oil to enter your engine.
This cleanable oil filter should be the last one you ever purchase.
Outer Clutch Cover O-Ring, Inner Clutch Cover Gasket, Stator Cover Gasket.
Sold individually, not as a kit
T-Rex stands are made from steel tubing finished in black powder for durability. Back by a 3-Year limited warranty for any material or manufacturing defects. Rest assured that you are getting best material commercially available.
Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools.
The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option.
Wider foot pegs for sure-footed comfort.
17-4 cast stainless steel.
| Width | 1.97" |
| Length | 3.18" |
50mm step width provides better grip and control
ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology. Try the grip with the technical advantage of three dedicated rubber compounds.
The difference between the original Pillow Top and the Pillow Top Lite is the overall diameter of the grip surface. The Lite offers a smaller diameter so the grips don't feel as large reducing fatigue in your hands while riding.
ProTaper Pillow Top Grip with 3-D (Tri-Density) Technology. Try the grip with the technical advantage of three dedicated rubber compounds.
Each pattern is available in three advanced synthetic rubber compounds. This means you can have the optimum combination of strength, tackiness and shock absorption to suit every riding condition and individual style. Soft grip is extremely soft, giving you a very comfortable ride, great feel and reduces the chance of blisters; however, because the grip is so soft, it wears quickly. Medium is a compromise between firm and soft. Firm grip has the same feel as a stock grip, it is very strong and has very good resistance to tearing and abrasion. Half Waffle has waffle pattern in finger area for traction and diamond pattern on palm side to reduce blisters. Full Waffle: designed after the CR Honda® grip.
Eight ultra-bright amber LED lights in a sleek design. Flexible stem helps absorb the occasional hit. Available in 2 pack or 4 pack
Recommended to use resistor for proper turn signal flash rate.
Specifications
If you just installed aftermarket LED turn signals or an LED integrated tail light and your turn signals are flashing way too fast, or perhaps simply staying on completely, you're at the right place to find the solution! The TST Gen2-SK LED Flasher Relay fixes what we call "hyperflash". It slows the flash rate down to a pre-set 85 cycles per minute but can be sped up or slowed down using the adjustment dial located within the unit so you can get the exact speed you are looking for. The plug-and-play installation means that you don't need to splice in any load balancing resistors that generate unnecessary heat and require splicing into your stock wires. Simply remove the stock relay and install your new TST relay and your wiring job is done. It's that simple!
Please make sure your bike uses a 2-pin relay for the signaling system. If your bike has hazard lights it may need the 4-pin relay. Please also note the pin configuration and make sure it matches what is on your bike. It is very important to verify fitment before making your purchase.
The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail/stop light function. 3 white LED's are used for license plate illumination. Included is a set of turn signal brackets that bolt to the mount. These are designed for a small signal with a 8mm mounting stud.
Taillight and brake light Attaches to the top of the rear fender. Dimensions: 3 1/2" wide x 2" long x 3/4" tall. D.O.T. approved.
If you're like us, you hate the long floppy vent hose hanging off the cap of your aftermarket tank.
This one-way vent cap replaces the long hose with a short one only about 2" long. It allows air into your tank but prevents fuel from sloshing out.
Machined from billet alloy and anodized for good looks.
Not for stock fuel tanks!
Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for wherever your adventure takes you! This tank is made from POLYETHYLENE CROSSLINK for extra strength and durability.
DOES NOT FIT NEW KLX300 "R" Models
Does your stock vacuum operated petcock not shut off when your bike is parked? Replace your stock vacuum operated petcock with this manual one. Must be shut off any time the bike is parked for more than a few hours. Fits stock or aftermarket tanks. Plastic tanks may need the hole 'ovalized' to fit the dual standpipes.
Does not fit OEM XR650L metal tank
An Old School design that works great on today's Dual Sport bikes.
The rubber compound is engineered for high grip and long-lasting tread wear.
DOT approved, tube type, and might be the best value in a DOT knobbie.
An ADV tire designed in Australia for real off-road riding. Technically 25% stronger than many adventure tires with a tread deeper than most and a compound formulated to perform in a wide variety of conditions. The tread design on this tire is unique in that the blocks self-sharpen for better grip through the life of the tire.
If you want the best in traction, wear and dependability, try a set of Tractionator ADV Rear with Dual Venture Front. All sets now have Dual Venture Front with ADV Rear.
NOTE: All of the sizes listed are Tubeless Tires (unless otherwise noted) and can be used as such with tubeless certified wheels. Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.
Standard Duty tubes are made with seamless construction from natural rubber with heavy duty valves. Great replacements for stock tubes and perfect as spares to carry on your bike.
Don't forget a Rim Strip. New tubes deserve new rim strips.
Replacement Inner Tubes for your VanVan or TW200. Always a great idea to carry a spare on your adventures as the rear tube is often hard to find.
Each kit includes all necessary rubber components and brake pins.
High quality carbon steel brake rotor.
A great option for every day use, or on your spare rear wheel.
Rotors are laser-cut from high-carbon content 410 stainless steel then lap cross hatch ground and heat-treated. The finished rotors are mounted on a floating black steel carrier for durability and strength.
The oversize floating pins are CNC machined stainless steel rivets with stainless wave washers to ensure they will not crush as more traditional steel pressed rivets can. Finally, high-temp paint is applied to surfaces like cooling holes and edges to provide a clean, finished look.
Includes a fresh set of brake rotor bolts.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
The best product for those surfaces that mate together without a gasket. Like center cases, cam covers and the like.
Muc-Off Air Filter Cleaner is a state of the art, professional strength bio-degradeable cleaner that's designed to clean and care for foam filters. Its unique combination of active ingredients is formulated to rip through dirt and oil in seconds, without damaging the foam or glue.
Repair kit comes with everything you need to get your carb back in shape.
Here is the O-Ring that fits in the carburetor manifold. This is the manifold that holds the carb up to the cylinder head. The O-Ring mounts between this manifold and the cylinder head. When this O-Ring fails it allows air into your cylinder and makes your Air Fuel ratio too lean which causes the engine to run too hot.
This is an O.E. replacement diaphragm for your BST40 carburetor.
This is ONLY a replacement filter for the ProCycle ITG kit and is not a direct swap for OEM.
This kit is for the 36mm Mikuni CV carburetor and includes 2 Needles that have been developed by JD Jetting and manufactured for them to their exacting specifications. These two needles allow a wide range of tuning possibilities and provide correct fuel delivery at any throttle position.
4 allen type screws for the top of the carburetor are also enclosed should you strip out the stock screws during your tuning process. Complete instructions with photos, jetting suggestions for different set-ups and situations, 5 Main Jets, a Pilot Jet and a drill bit complete the package.
Kit includes:
Everything you need to dial in your FCR/DR650 conversion. Enough jetting to cover most modifications or altitudes.
Not for the stock carburetor Fits FCR-MX conversions Only
For reference, the stock gearing for the WR250R is 13/43 while the X model runs with a 13/42 stock configuration because of the SM wheels/tires. Both use a 108 link chain with the stock gearing.
The JT rear sprockets listed are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Limited availability on Aluminum from PBI. Manufactured from aircraft 7075 T651 Plate Aluminum.
If you want the additional low-end grunt that the 46, 48 or 50 tooth rear sprocket will give you, you will need longer chain as well.
New Rear Sprockets require new Sprocket Bolts because of a difference in the holes vs. the stock bolts.
Choose either a 14, 15, 16 or 17 tooth JT countershaft sprockets.
Go down in tooth count for faster acceleration.
Go up for lower RPMs at cruising speeds.
High quality steel front sprocket
For reference, the stock gearing for the WR250R is 13/43 while the X model runs 13/42 stock gearing.
Warp 9’s Pro Rim Locks are developed with Ice Track, Dirt Track and Flat Track Racers in mind!
Burnt Titanium Main Bolt
Lightweight Forged Aluminum Body
Black 7075 T6 Tower Nut and Base Washer
Base washer is machined to match each specific rim curvature for a perfect fit
About half the weight of OEM rim locks!
1.60 front – 1.8 oz
1.85 front – 2.0 oz
2.15 rear – 2.3 oz
2.50 rear – 2.7 0z
3.00 rear – 3.10 oz
Construction of these handguards feature heavy duty aluminum guards with colored plastic deflector shields. They offer great protection from those trees that jump out at you on the trail and the cold wind and rain you encounter on the street. They feature a deep bend on the outer bar end for maximum freedom of hand placement and high quality bar mounts on the inside.
Select your desired color.
Must add the corresponding size mounts to fit your handlebar.
For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.)
Please Note: These handguards do not fit the Yamaha T7
Replace these any time you feel excessive play in the sprocket hub.
Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.
Sold as a full set.
Genuine Suzuki super moto fender. A perfect match for the original gray plastic.
Quality replacement radiator air scoops. Sold in pairs for gen 1 KLR650.
Available in 4 colors.
Freshen up the look of your TW. New Plastic in Black or White. Includes Rear Fender, Side Panels, Headlight Cover, and Front Fender.
Choose a Kit with OEM Front Fender or after market SuperMoto fender.
SuperMoto fender kit includes our High Mount Fender Bracket!
Choose mechanical or hydraulic brake switches for your dual-sport conversion
10x1.25 thread. Low profile pressure switch for those applications with limited space above the brake banjo bolt. Kit includes a special replacement banjo bolt. Choose 10x1.25 thread pitch for most Japanese models. Choose 10x1.00 thread pitch for European bikes with Brembo brakes or Japanese bikes with Tokiko brakes.
Mondo Straps are named after the classic motorcycle movie, "Mondo Enduro". When they set out on their world trip they had hard luggage on their bikes. By the end of the movie the riders that were still pushing forward were all using simple straps and some homemade dry bags. The simple fact is soft luggage is more durable off road than hard luggage.
The Mondo Straps Kit has been designed to work with or without their Uprising Soft Rack. These straps allow you to use any bag you want for luggage. When installed properly you will be able to thrash about offroad and your luggage will stay put!
To use the Mondo Straps make a girth hitch around any mount point on your bike. Next, thread the flat runner back through the heavy duty metal cam buckle and pull it tight. The Mondo straps are easy on and easy off. The integrated tensioner system will keep your luggage in place no matter what terrain your adventure takes you on!
Kit Includes:
You can add the double D ring loop to any 1" flat webbing system. This simple piece adds a lot of flexibility to any luggage system you are using. Instantly and easily create a mount point or adjustment point on almost anything. Double D Rings can be used as a secondary buckle and works the same way as a helmet strap. However, the double D rings should NOT be used as a primary means of securing luggage.
Available in 6 colors.
CONSTRUCTION FEATURES
The perfect dry trail pack from Moose. Constructed of heavy-duty waterproof tarpaulin with heat-welded seams. Heavy-duty ITW quick-release buckles and YKK water-resistant zippered external pockets make for a versitle bag.
The roll-down top creates a truly waterproof seal for the main compartment. Dual compression straps provide a secure closure and can be used to store gear externally as well. Coated tarpaulin material makes cleaning a breeze. Available in three great sizes - 25, 40 and 60 liters.
If you like these bags, you might like the matching ADV1 Backpack.
3.5MM X 20FT
Made from Tough but lightweight 12 Strand SPECTRA / UHMWPE
2200LBS Break Strength
Double Looped Ends
Each Looped end is Covered in a Kevlar Sheath to protect the rope from abrasion
Simplify self recovery with this quick deploy Z-Drag kit. It can sap your energy trying to get your bike unstuck. It can also fall in a way that makes it very difficult to pick up. The Z-Drag is a common rig to give you a mechanical advantage for reduced pull. The combination of roller cams provides a 4:1 pulling ratio for self recovery and a 5:1 ratio when you have help. A laminated instruction card is included in the bag.
| Quick Deploy | No knowledge of rigging and knot work required. Our Z-Drag comes out of the bag rigged and ready to use. |
| Color Coded | For simple operation. |
| Locking Carabiners | Two climbing rated, locking carabiners for secure attachment. |
| Lightweight | Approx. 3 pounds and small enough to pack on a motorcycle. |
| Strong | Even though its small, it still has a 1000 pound working load. |
| Versatile | With a 74' mainline you will always have enough length to get creative in a tough situation. |
| Multi-Function Bag | The bag features MOLLE compatible webbing on the outside for external attachment. The bag can also be utilized as a dead man anchor. |
| Storage | Comes in a 1000D Cordura storage bag. |
| Recovery | Can be used for solo recovery or with help from friends. |
| Trail Repairs | Can easily be used to hoist your bike from an overhead support for repairs and maintenance while traveling. |
| Clearing Trails | Move fallen trees out or other obstacles out of the way. |
| Camping | Can be used to hoist a bear bag, act as a ridge line for stringing a tarp, etc. |
ADV Sushi is a webbing reinforced velcro strap with integrated daisy loops. These are as handy as zip ties and duct tape. This is one of those products that you will use frequently if you have them with you.
A single strap was load tested at 200 pounds before it let go and a single strap held 50 pounds overnight with no issues.
Use this kit to build your custom solutions such as a fuel bottle holster, spare tube carrier, or use them to attach your bags to your Uprising Soft Rack. The possibilities are truly endless.
This Kit Includes:
RotoPax are Rotational Molded - the process which produces indisputably superior products.
Need to mount two containers? A water and a fuel? Two waters? Finally, you can stack multiple packs together! Use in conjunction with a pack mount. You will need to purchase the Single Mount as well as the Extender.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 2 |
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 2 |
This is the more economical alternative to eliminating the 990 Adventure airbox. Better breathing equals more power. The ITG filter kit makes air filter service a snap. It also simplifies other engine and intake maintenance chores. Our kit features a steel base plate which will not deform like plastic and does not conduct heat as much as aluminum. The white powder coating also helps reflect engine heat. To take advantage of the increased airflow, we recommend upgrading your fuel injection map with TuneEcu or a Power Commander.
The FMF Power-Up jet kit makes jetting your carb simple. They teamed up with DynoJet to produce a kit that offers you a selection of jets and/or needles to get maximum horsepower out of your KLR. The easy to use instructions have diagrams and step-by-step procedures to help you get your jetting where it needs to be, no matter what elevation you ride at. No more driving back and forth to the dealer with a handful of jets and needles with a million questions running around in your head about where to start or turn next.
Honda XR650L rear shock upgrade. The experts at Cogent Dynamics know suspension! A proven performance rear shock for your XR650L for use under the most demanding conditions and on the roughest terrain worldwide.
Damping rates optimized to your specific needs, giving you the best ride comfort, traction and control. Frequency and velocity sensing valving works great over wide ranging conditions. Low internal friction. All CNC machined components for top quality and performance. Compact and rigid design with internal separator piston. Adjustable for spring preload and rebound damping. Fully serviceable shock is designed for the long haul.
*Spring color may vary due to specification requirement and availability.
| Standard Spring | 10.71 kg/mm |
| Heavy Duty Spring | 12.50 kg/mm |
| Low Shock | 1.5 inches lower |
Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.
With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way.
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.
The Swiftkicker is 100% manufactured in the USA from the highest quality components.
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.
Measured from the center of the pivot to the bottom of the foot.
Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.
With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way.
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.
The Swiftkicker is 100% manufactured in the USA from the highest quality components.
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.
Measured from the center of the pivot to the bottom of the foot.
As pictured; includes:
| 2 | Classic Swingarm Stickers (1% power gain) |
| 1 | Sheet of 3 small "black" stickers |
| 1 | Sheet of 3 small "yellow" stickers |
| 2 | "Adventure Begins Here" stickers |
| 1 | "Back Roads or No Roads" magnet |
