Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
You pay $3.59 per filter with our value 5-pack!
Made from laser-cut, medical-grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area over many paper filters, catching debris down to 35 microns. The FLO filter pleat seam is welded and able to withstand up to 600 deg. F. Filter maintains consistent flow under all conditions including extreme heat, the presence of water and cold start-ups where paper filters can flow so poorly that they often cause the bypass valve to open and allow unfiltered oil to enter your engine.
This cleanable oil filter should be the last one you ever purchase.
Providing unbeatable performance and exceptional value, Hi-Flo Filter is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
Grab our 5-pack and save both time and money!
This is an extended version of the stock DR650 clutch release arm that is manufactured by Suzuki.
Upgrading to a longer clutch release arm will lighten the pull of the clutch lever through means of increased leverage. This means less fatigue, quicker clutch engagement, easier clutch modulation and longer rides.
The extended clutch arm will not offer a drastic change in clutch pull. If you're looking for a major change in clutch pull at the lever, we recommend getting a Magura hydraulic clutch kit.
Complete set of friction plates, HD springs and steel separator plates prevent premature driven plate wear, oil muddying and loss of stack height. Built with swaged aluminum carriers that spread the load on the clutch basket and prevent clutch basket "dogging". Anti-swell, alloy impregnated heavy-duty facings for smooth clutch action. Allows modulation, unlike paper clutches which tend to snatch. Don't forget to add a fresh gasket.
Stock and typical after market drain plugs can protrude past some skid plates. This steel low profile drain plug stays inside the skid plate so it can't be snagged by passing objects.
Comes with 4 crush washers.
Generator cover gasket to seal up the cover once you have your new Doohickey in place. New OEM gasket. What else can we say? If in doubt, put in a new one.
This 3rd gear set is made for us by Nova Racing Transmissions in England to replace the fragile stock third gear set. These folks build complete transmissions for World Superbike teams among others, so we believe them to be highly qualified to build this set of replacement gears.
These gears are made from a high quality special alloy steel and then heat treated and superfinished. The mainshaft drive gear and the countershaft driven gear are sold only as a set.
The PSR Oil Filler Caps are CNC machined from high quality aluminum and come with an E-clip that is already safety wired to a mounting tab. The wire is covered with silicone tubing that will not melt or discolor. Available in silver, black and gun metal.
Includes forged JE 89mm piston 10.5:1 piston, Rings, Clips, Pin, big bore sleeve and top end gasket set. You will have to have the big bore sleeve installed in your cylinder and bored to fit the larger piston.
These gaskets seal the joint between the head pipe and muffler. They are easily damaged when removing the original muffler. Get a fresh pair now to ease installation of your new performance muffler. Sold as a set of 2.
This gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers do not require a joint gasket but the all other aftermarket mufflers as well as the stock muffler require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.
This is a new gasket for the cylinder head - head pipe junction. Installing a new one with your new header will ensure a good seal and no exhaust leak.
Set your bike apart with a custom exhaust look. Withstands direct heat up to 2000°F.
Protect your head pipe from rock damage. This stainless steel spine clamps to your head pipe to add a layer of protective armor between your vulnerable pipe and those nasty rocks or logs. Fits the stock headpipe. Will fit the FMF head pipe with the addition of larger clamps.
The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.
X3 EVO represents the off-road evolution: LeoVince has combined all its experience in the off-road world with cutting-edge materials and Italian design, enhancing freedom in its purest form.
The X3 EVO body is made of AISI 304 stainless steel with TIG welds handcrafted by specialized operators, to guarantee long-lasting performance. X3 EVO will allow you to face the most extreme environments and conditions because it does not fear water or mud, nor wear over time.
The LV logo is their tribute to a motorcycle culture that we have loved for 70 years and is laser etched on the body of the exhaust: it is as endless as their passion.
They manufacture the end cap in 100% real carbon, with their special 2x2 twill carbon fiber, specifically designed to resist high temperatures and make the X3 EVO even lighter.
The matte clear coating, in addition to enhancing the carbon texture, protects the end cap from wear and UV rays, keeping the X3 EVO always in a perfect shape.
The sound of X3 EVO is already unmistakable at low revs. X3 EVO has a direct interior, specially conceived to channel the exhaust gas in an optimal way, to unleash a deep sound, giving a new voice to your bike.
The X3 EVO's Spark arrester has been tested and approved by the United States Forest Service and is essential for off-road riding in compliance with regulations, with more peace of mind, more respect for the environment and more fun.
A quality replacement speedometer cable from Motion Pro.
A quality set of replacement throttle cables from Motion Pro
The Trail Mirror is a simple solution for any dirtbike or mountain bike. Gives you hindsight when you need it, but you forget it's there otherwise.
Zip ties directly to the bar- no hardware required.
Sold individually
A stock replacement brake pedal for the DR650. Nothing fancy but sure gets the job done. Just order it up and get back on the trail. See our Brake Pedal Adjuster Bracket that allows you to adjust the position of your brake pedal to perfection.
For the frame drain on your XR650L ,extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!
Motoz Tractionator Desert H/T series of tires are renowned for great traction and long wear life. These tires are designed to handle hard terrain, fast and rocky trails as well as gravel roads and desert hard pack. Tricky off-cambers, ruts and hard braking at extreme lean angles are no problem for this DOT approved tire.
Note: Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.
This street-legal knobby from Pirelli has good stability and cornering precision thanks to the carcass stiffness. The tread pattern optimized for use on dirt and gravel roads, cross-country racing and desert tours. It has lasting off-road performance and knob tearing resistance due to the special off-road compound.
This is a great Dual-Sport tire from Dunlop. Designed for the true 50/50 rider. An Adventure product for the price-conscious customer. Full tread depth pattern designed for rigorous off-road use yields excellent traction on everything from hard-packed fire roads to soft single-track trails. Versatile tire performance allows riders to travel on the street and venture off-road. A tire equipped to go anywhere, the D605 is a value option for the all-around rider. DOT approved.
RallZ is the most aggressive off-road adventure tire in the Motoz range. Its DNA is part desert race tire and part long distance adventure tire. An ADV tire designed in Australia for adventure and rally use. Based on the popular Tractionator Adventure but with more aggressive off-road traction in all weather extremes.
DOT ECER75 approved.
NOTE: Tubes can be run in Tubeless (TL) tires, but a Tube Type (TT) tire cannot be run Tubeless.
The Rally windscreen from Parabellum is the perfect protection from wind and debris without sacrificing technical off-road capabilities. This is an upright rally type windscreen that looks aggressive and performs well under all types of riding. Designed primarily for the off-road / dualsport enthusiast, this shield keeps pressure off the rider's chest while commuting from home to adventure and back.
This windscreen mounts securely to the three stock windshield holes as well as the two side cowling mounts. The shield is 14 inches tall, 13 inches wide at the bottom narrowing to 11 inches at the top. Made from 3/16" military aircraft grade cast acrylic.
Quality windscreen made from Lucite aircraft acrylic making it more rigid and optically clearer than OEM windscreens
These models are 2"-4" shorter or 2"-4" taller than stock to meet your particular riding preference.
Includes new Suzuki side panels, heat shield, headlight cover, rear fender and your choice of aftermarket off-road or supermoto front fender.
Choice of off-road or supermoto (SM) front fender.
Blue kits come with white side panels.
Rear Fender comes with built in tabs designed to be used with Maier USA Side Panels.
OEM Suzuki headlight cowling.
Quality replacement headlight fairing for Gen 1 KLR650.
Available in 4 colors.
Quality replacement radiator air scoops. Sold in pairs for gen 1 KLR650.
Available in 4 colors.
Has your TM40 carburetor been sitting for too long and now needs to be rebuilt? Then what you need is this TM40 Rebuild Kit that contains Genuine Mikuni replacement parts.
This kit includes:
Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air- the number 1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow
Unsurpassed in airflow, dirt stopping and overall performance. Adding a pre-filter to your intake system gives you extra protection from damaging contaminants.
Is the cylinder head intake boot on your DR650 cracked or weathered, is it missing parts of the lip to seal around the carburetor, have you recently pulled the intake boot off only to realize the O-ring behind it is hard & brittle? This kit is your solution to solving some of those mystery problems and make your bike like new again. There can be a great deal of heat that can radiate behind the cylinder head on a DR650 as it is an air cooled engine. With that comes long term maintenance items that will need to be replaced due to them being made of materials that cannot withstand those constant heat cycles indefinitely.
Our kit includes O.E. parts from Suzuki to include:
The Chilly Exhaust Heat Shield is the most effective heat shield on the market. The innovative three piece design consists of a top shield attached to 2 rails with rivets and spacers. This reduces the contact area and slows down heat transfer. They have incorporated a patented, insulated reflective blanket on the underside of the shield to reduce radiant heat transfer. The included stainless steel clamp makes it simple to install.
We highly recommend a heat shield if you run soft luggage without hard racks.
FEATURES:
DIMENSIONS:
If you already have a Quad Lock Case, you can Twist Lock and Go with any of these secure mounts.
Or Choose the Universal Adaptor to use your current phone case.
The Quad Lock® Handlebar Mount is the ultimate smartphone mount for motorcycles, compatible with all Quad Lock® Cases including the Quad Lock® Universal Adaptor for other Android phone devices.
The Quad Lock® Handlebar Mount gives you the flexibility to mount your phone in a convenient and visible location using a rotating head and includes an extension arm if extra clearance is required. With your phone securely mounted to your motorcycle, you can use navigation apps to guide you to your location with ease and always stay connected.
Standard:
NOTE: Case not included
Motorcycle Vibration Dampener is recommended for use with this product.
If you already have a Quad Lock Case, or Universal Adapter and Mount you can add these accessories to Twist Lock and Go on another level.
The level of vibration from some motorcycles can affect the image stabilisation on new smartphones. The Quad Lock Vibration Dampener ensures you can confidently mount your smartphone to any motorcycle.
FURTHER PROTECT YOUR SMARTPHONE
Compatible with all Quad Lock Motorcycle Mounts and Quad Lock Motorcycle Accessories, the Quad Lock Vibration Dampener reduces over 90% of high frequency vibrations produced by motorcycles.
PRECISION ENGINEERED
Featuring a dual chassis suspension system with precision engineered silicone grommets, the Vibration Dampener absorbs vibrations to protect your smartphone’s camera.
EASY TO INSTALL
The Quad Lock Vibration Dampener comes with everything you need to integrate with your existing Quad Lock Motorcycle Mount and can be installed in minutes.
PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash.
Sold as a pair. Easy to Install
Precision Motorcycle Racks strongly recommends these side racks be used with their Top Rack because the racks use each other to mount properly. They were never intended to be used by themselves without the rear rack.
If you are going to mount these side racks without the use of their top rack please select the extra hardware kit option that includes 2 brackets, 2 steel spacers, and an extra hardware kit that is required for proper installation.
These side racks will not play nice with any other brand rear rack, and installation without their top rack will prove to be quite difficult.
The B&B Off Road Engineering rear carry rack is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible. Our carry racks are Tig welded with a polished finish and are sturdy enough to use as a grab handle.
DIMENSIONS
Width Flat Surface Approx 18cm
Length Approx 33cm – Total Length Approx 45cm
Please Note- To fit rack, two holes need to be drilled into the rear guard. The position of holes are already marked on genuine Yamaha guard so no template is required.
These are high-quality straps made by Givi. They have a nylon belt with an anti-slip metal safety buckle. The long strap is 67" long by 1" wide with a 100 kg maximum traction load. The short straps are 39" long by 3/4" wide with a 75 kg maximum traction load.
Size: 25mm-1700mm
2 high-quality bushings per set. They recommend changing bushings every 40 hours or at least once a year to get the best performance out of a set. If you are on an Adventure Bike and are doing a lot of road miles they recommend swapping out bushings once a year to ensure that you get the most vibration dampening of the bushings.
Every new set of pegs comes with a 90A bushing installed. This is a medium flex rating.
80A is the softest and 95A lock-out is the stiffest and has the least amount of flex.
The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference.
The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.
For use on Motion Factory Foot Pegs Only
50mm step width provides better grip and control
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm.
Our complete foot peg assemblies. 1-3/4" lower than stock. No extra brackets that hang down below the frame. Easier on the knees. Wider platform Yamaha YZ style footpegs are stronger and give you firmer footing. Mount solid to the frame. No more 'droopy' feeling when standing on the stock pegs. Lowering your footpegs makes it easier to stand and less of a reach down to the bars when standing.
Now you can get our Low Pegs with MK4 Pivot Pegz or black Fastway ADV pegs (both Yamaha YZ pegs) installed!
The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option.
Wider foot pegs for sure-footed comfort.
17-4 cast stainless steel.
| Width | 1.97" |
| Length | 3.18" |
Upgrade your Honda XR650L with a Subframe Brace Kit, designed to enhance strength and rigidity for your bike. This complete kit connects the frame and subframe, reinforcing the structure to support increased load capacity—perfect for riders using side cases, top cases, and rear racks.
Key Features:
High-Quality Materials: Attachment points are machined from 6061-T6 billet aluminum for superior strength and durability.. The 6.5mm thick support bars are laser-cut for a perfect fit.
Easy Installation: No cutting, drilling, welding, or modifications required for installation. Easy 20 min installation.
Enhanced Load Capacity: Provides added rigidity and support to the subframe, improving bike stability when carrying additional gear.
Exhaust Compatibility: Compatible with both STOCK Exhaust and FMF Exhaust systems.
Hardened chrome vanadium steel with built in rubber insert to hold spark plug steady.
Thin wall bi-hex sockets designed to access narrow spark plug holes.
The genuine factory shop service and repair manual. This is the reference manual Yamaha dealers use in their service departments. It has all the necessary info to do any maintenance or repairs to your WR250R or X.
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of the big Acerbis or Clarke tank? The 4.0 gallon tank from IMS might be just right. Includes cap, uses stock petcock.
You’d be amazed at the dirt and debris that can work its way into your gas can – and from there, your fuel tank. Twin Air’s monofilament screen pocket inserts in your tank to catch particles as small as 40 microns (.00165”) while allowing the gas to flow freely.
The flange is custom-sized for each modern 4-stroke model to ensure a leak-proof seal. Just remove the filter periodically, turn it inside-out, and clean out the debris that could have been in your engine.
Will not work with factory locking gas caps.
Inside tank inlet diameter must be approximately 43.5mm (1.71") to fit.
Includes all necessary o-rings and diaphragms
For reference, the stock gearing for the WR250R is 13/43 while the X model runs with a 13/42 stock configuration because of the SM wheels/tires. Both use a 108 link chain with the stock gearing.
The JT rear sprockets listed are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Limited availability on Aluminum from PBI. Manufactured from aircraft 7075 T651 Plate Aluminum.
If you want the additional low-end grunt that the 46, 48 or 50 tooth rear sprocket will give you, you will need longer chain as well.
New Rear Sprockets require new Sprocket Bolts because of a difference in the holes vs. the stock bolts.
Now you can have minimum output shaft wear, minimum chain drive wear with the FRITZCO DRIVELINE sprocket. The design of their sprockets provide correct chain alignment, allows for full spline contact with the XR650L's output shaft, fit the counter shaft either way, and straight up no hassle installation with the OEM two bolt retainer and fasteners (except 13 tooth that comes with it's own quick change retainer). Their sprockets are machined from alloy steel that is comparable in every way to OEM Honda and the best offered by other manufactures. The sprockets are then given a heat treatment that provides a compatible sprocket for the Honda output shaft and longest wear life possible.
A way to double the sprockets life would be to have a sprocket that fits on the shaft either way so both sides of the teeth can be used. Bear in mind you can't wear one side of the teeth all the way through, then flip the sprocket, and expect double life. You must reverse when a normal wear pattern develops.
16 tooth sprocket is the biggest front sprocket that will run with the standard 110 link chain and 45 tooth rear sprocket on an XR650L
The OEM cover will require modifying to use the 16 tooth sprocket on your XR650L.
High quality steel rear sprockets from 39 to 53 teeth.
Sprocket color may differ depending on size.
There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.
You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.
We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.
This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.
Easily turn your blinkers into additional running lights and brake lights (rear) for added visibility.
White light in the front and red in the rear. Rear red running lights and bright red brake lights. You can omit the running and brake lights if you wish and still have the best blinkers on the market.
Dazzling bright Amber blinker functions.
Everything comes in a spring-loaded stock designed to keep it safe from those unexpected tip-overs, crashes, or encounters with brush and trees. They’re flexible enough to bend 360 degrees, yet tough, durable, and almost impossible to break!
If you have a single indicator light for the blinkers that is not built into the display and is not LED you will need the diode kit (AKA DR650) If it is built into the speedo display it should not require the diode kit.
Available in a generic kit with Bullet connectors supplied. Great for your DR or almost any other bike with a single post blinker setup. These will work well on bikes that use a flasher, but you might have to add the female side of the connectors that are included in the kit.
Not for Yamaha T7, see model specific listing
Now available in the original version or the Ultra version. The original uses the front two emitters for low beam and then switches to the rear two emitters for high beam. The Ultra uses the front two emitters for low beam and then runs all 4 emitters on high beam at a reduced wattage. Wattage is 38 watts on low and 38 watts on high.
This bulb uses 4 Cree XHP 50 emitters, capable of more than 2500 lumens each. At 5000 lumens on each function, this is the brightest Cyclops H4 bulb.
*UNIVERSAL PART, PLEASE CHECK YOUR APPLICATION FOR FITMENT
A game changer in auxiliary lights. High output, compact and lightweight!
The New Cyclops Aurora 2 inch lights rated at 4000 lumens combined. Using an authentic top binned Cree XHP50 emitter these lights pack a punch!
Available with or without the daytime Running light option (DRL) which can also be a front blinker. (you may need an LED flasher to do that)
Like all Cyclops lights we only use the Best Real Cree emitters. R113, R10 TUV and Emark certified IP68 rated.
Includes a full relayed wire harness designed for a Motorcycle. No need to use a switch if running the DRL version, also no need for a switch if using the skene dimmer or want the lights on in high beam and off in low beam. The factory switch will work for these applications.
Look at these quality features!
There is a lot of technology packed into this tail light/fender eliminator kit. You have programmable turn signals and Safety Brake Pulsing both built into this product.
You can enable or disable the safety brake pulsing feature.
This kit includes only the highest quality components, including the pre-installed 12oClockLabs processor board, which is made in the USA.
We recommend a "Fixed Rate Flasher" unit for use with this kit. When you install aftermarket signals it changes the load on a factory signal system.
This kit does not include parts to mount aftermarket turn signals. The pre-installed processor board allows the turn signals to be integrated in to the tail light.
This kit includes a DOT LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
How does this headlight compare to our original TW200 kit? First and foremost, this kit has SAE/DOT markings and a much wider/brighter high beam pattern. The low beam is very similar to our original kit: wide, flat, and bright but with more punch. The DOT headlight assembly has also proven to be more durable than the original headlight.
Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Approved
CE, RoHS, ISO9002, IP67
No cutting, drilling, or wiring modifications! Installation takes 5 minutes.
Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.
Please note that this product is not compatible with the 1987 TW200.
This kit includes the all new Morimoto 4×6 LED headlight and a pre-assembled JNS Engineering adjustable mounting bracket set. Like the rest of the JNS headlight kits, installation is a simple 5 minute plug-and-play procedure.
This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform/controlled, and features a proper upper cut-off. The high beam is amazingly bright, eliminating the need for auxiliary lighting (money saved!). Plus the 5,000K color temperature is extremely easy on the eyes. The materials, construction, and aesthetics are all top notch.
It’s a next level headlight, you won’t be disappointed.
Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive
Does not fit '87 TW200 because that year has a unique AC powered headlight circuit.
Both kits include all bushings, snap rings, and washers.
Gen 2 kit also includes the necessary O-rings.
Gen 1 kits are OEM bushings, snap rings and washers.
Lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.
Stock spring rate 0.60 kg/mm
Race Tech Recommends 5w oil, 2 qts to reach 110 mm oil level.
In stock form, the forks, featuring a single spring design are under sprung for any rider over 100 pounds. With limited travel, adding a stiffer spring in the right leg only per the stock design was not a viable option.
Race Tech instead offers a High Performance Spring Kit that adds a stiffer spring to the other fork. (The overall spring rate in the forks is the average spring rate between both legs.) This upgrade will make a drastic improvement in handling for most riders.
0.50KG/MM KIT
Included in this kit are .42 kg/mm fork springs, Cogent DDC (Drop in Damper Cartridge) performance cartridges and two bottles of 5w fork oil.
Developed by the KLR suspenison experts at Cogent, this set of springs will stiffen up that wimpy KLR front end. Choose between .64 kg/mm springs (60% stiffer than stock) or .70 kg/mm units (75% stiffer than stock).
Will not work for 2014-Cur 'Mid-Year' New Edition Model
These springs are custom wound specifically for the XT225. Stiffer than the .36 kg/mm stock springs, these will make your front perform significantly better. Combine them with the Cogent DDC's and you will be very happy with the results. Sold as pairs.
The Pro-Series is an excellent replacement for the stock shock. With both compression and rebound adjustable as well as preload adjustable, you can tailor the performance to match your riding style. Compact and rigid design with piggyback type reservoir specifically engineered for your WR250R. Fully serviceable shock is designed for the long haul.
Select the spring you want installed based on the load you plan to carry. Choose the 'standard' 8.15kg/mm spring for rider/ luggage up to 220lbs. Weigh more than 220 lbs, or are loaded to the max, think about the 10.19kg/mm 'heavy' spring.
Replace the internal components in your shock with a completely updated design with adjustments for both compression and rebound damping.
The new shaft assembly has improved valving for both compression and rebound, a thicker, stronger shaft, new seal head and bottoming bumper. Comes as a complete assembly ready to go into your shock body. You can add choice of rear spring (required).
Add a bottle of 3w Shock Oil to your order so you can start your project right away.
These Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. No disassembly of your forks, no drilling of damper rods. Just change the oil to 5w and install the DDCs under the springs and hit the trails.
Stiffer fork springs are required to realize the full benefits of the DDCs. .42 kg/mm springs are the springs recommended for just about anybody out there. Please call if you have any further questions.
The DDCs are not recommended for use with progressive springs.
The DDC Install/Removal Tool which makes installation that much easier.
Adjustable lowering links by PSR. Adjusts the rear suspension from stock height to 4 inches lower.
The X-Factory Handguards from Acerbis are designed with a steel bar encased in an injection-molded Nylon composite. A replaceable dual-injected polypropylene shield attaches to the bar, providing excellent protection against debris and harsh conditions.
Included with the handguards is a universal mount kit, enabling installation on either 7/8" or 1 1/8" handlebars.
Will not fit XT250 with stock handlebars (oversize bars ok). Recommend Acerbis Rally Pro X-Strong to clear master cylinder.
Closed handguard with aluminum bar and bracelets.
Ultra-durable closed handguard designed for those seeking greater protection while competing or riding in enduro, hard-enduro and cross-country racing.
Equipped with a 35 mm "C" section anticorodal bar. Provides 5 times more resistance than the classic handguard with an aluminum bar.
The cuffs, oversized with a thickness of 19 mm, guarantee greater strength and increased torsional capacity.
Expanders made entirely of steel.
Cover is impact resistant; wide area protects the pilot's hands more, while flexible lower area absorbs any accidental contact with the knee.
Mounting kit included. Mounts to all off-road competition bikes (motocross and enduro) with inner size from 13.5-16 mm and outer size from 22-28 mm. Works with 7/8" or 1-1/8" bars.
Co-molded logo.
High quality aluminum caliper guards from Works Connection protects your brake caliper and looks great too.
This is the ultimate radiator guard for the CRF250L. Protects your radiator from both front and side impacts.
A rear mounting bracket provides that extra support. Constructed from 1/8" aluminum, the kit includes all necessary mounting hardware for a very simple installation.
Givi makes a great set of Crash Bars available for the Africa Twin. If your intentions include off-road riding of any kind, you really should not go without protection. Not only for you, but for your bike too. Even a slow-speed tip-over can cause damage that would make riding away impossible.
For the upper set, you just need to select the matching color to the lowers you have ordered. Install them all at once, or the lowers alone for a while, then the uppers. You cannot order the uppers without the lowers though as they will no mount correctly. The upper crash bars protect important radiators and bodywork. Essential in the event of any kind of crash. These also make excellent mounts for auxiliary lights for added visibility.
Included with each piece you receive a complete set of instructions and all mounting hardware required, in typical Givi fashion.
NOTE: The upper units REQUIRE the lower crash guards for proper mounting and are not a stand alone item!
Please Note that these Crash Bars are also compatible with the Givi Skid Plate.
Use this tool to check for air leaks in two-stroke engines. It includes air pressure gauge, pump-up bulb and most fittings and adapters for single and twin-cylinder two-stroke motorcycle engines. Packed in a convenient carrying case with instructions.
Made from precision-drawn, chrome-vanadium tool steel, the BikeMaster® 9-Piece Ball End Hex Wrench Set and Holder features a bead-blasted surface for a better grip and a corrosion-resistant coating. They have a ball end, allowing an angled reach and access to obscured bolts. It comes with a durable holder and manufacturer's lifetime warranty.
Comes with sizes 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm and 10mm
Repair kit for your rear disc brake master cylinder.
EBC Double H Sintered pads feature the HH friction rating - the highest in the industry.
Provides maximum brake effect and lasts twice as long as organic pads.
• Front pad kits include pads for both rotors
Sintered Pads from EBC are the best pads we have found for the KLR, they provide good performance in all conditions yet still give you long pad life.
These sets include front and rear brake pads.
Premium quality EBC Rear brake shoes.
Organic brake pads contain man-made high-performance fibers that are used for their light weight, high strength abrasion resistance and thermal stability. These Aramid fibers have a high strength-to-weight, thermal stability and abrasion resistance to provide advantages over steel fiber-based products. They provide excellent stopping power without noise and rotor galling but still provide fingertip control and strong, predictable brake response.
Double-H sintered metal brake pads feature the HH friction rating, the highest in the industry. These pads provide maximum brake effect and last twice as long as organic pads.
Semi-sintered pads have an all new recipe containing 30% copper by weight with an organic matrix. This design combines the long life of a sintered pad with the great feel and lack of rotor damage common with full-sintered pads. These can be used to replace Kevlar or sintered metal compound pads.
Set includes pads for both front calipers.
All that you need to repair and inflate your tire on the road or trail.
Kit includes:
CO² cartridges cannot be transported on an aircraft.
Seat Concepts dual-sport/adventure seat-kits incorporate a wider seating area for the rider, which results in more even weight distribution, while reducing pressure points. Each individual seat model has been specially designed to increase comfort without compromising ride-ability. The more aggressive the bike, the more aggressive the seat-kit.
Each kit contains detailed instructions for easy "Do It Yourself" installation. This provides the highest level of quality & comfort at an affordable price.
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
| Width: | 9 1/4" (235mm) |
| Height: | Same as OEM |
Note:
This seat is based on the off-road version of this bike. The street version is 1 inch lower than this seat.
Will NOT fit DRZ 250
Maxima light viscosity 3w 75-390 shock oil, 1 US Quart.
Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.
With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way.
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.
The Swiftkicker is 100% manufactured in the USA from the highest quality components.
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.
Measured from the center of the pivot to the bottom of the foot.
Designed to enhance the appearance of your TW200, yet provide greater riding distance per tankful. This larger fuel tank has double the capacity of the stock tank at 3.6 Gallons, yet very slim and sleek. This tank has a custom design that will allow the use of OEM & Maier side covers. These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.
Comes with New Screw Cap.
Requires OEM/Stock petcock and oval rubber grommets for install.
If you do not have the grommets or if your O.E. grommets are in poor condition you can add these to your tank order.
Ride in warm temperatures a lot? Worried about your motor oil just getting too hot? The Trail Tech Universal Fan Kit mounts up to the backside of the DR's oil cooler to draw cool air across it and keep those oil temps down. An electronic temperature sensor mounts to the fan, no need to cut any fluid lines, and automatically turns the fan on when needed to keep the temperature in the optimum range.
The activation sensor can be set wherever you like to keep the temperature right where you want it. Backlit for easy viewing anytime it also includes a volt meter.
Kit Contents
A new high output stator for the XR650L. 25% more output than the stock unit. Approximately 50 additional watts. Now you can have enough power to run those driving lights and/or heated riding gear!
Stock chain guard crack and crumble on you? Won't happen to this unit CNC machined from 2.5mm marine grade aluminum. Polished to a beautiful sheen that will give your DR that little twinkle as well as better protection.
