A complete set of gaskets, o-rings and oil seals. Everything you will need when doing a complete engine re-assembly.
Always a good idea to put in a new set of Oil Change O-Rings at the first sign of any leakage. This package gives you the three most important: oil filter cap and the one behind the filter as well as the one on the filler cap. All are new OEM Suzuki O-Rings.
A Suzuki OEM gasket for the Cam Chain Tensioner. You are going to need it if you work on your starter motor. It is not a good idea to re-use this gasket. If it blows out, it will dump a large amount of oil onto your right foot.
Add a backup kick start system to your electric start DRZ400. Complete with everything you need to add the kick starter to your bike.
This kit will fit all DRZ400s but the manual decompression lever can only be installed on the 2006 to Current DRZ400 E models.
Higher pressure in the cooling system, raises the coolant boiling point and increases protection from coolant loss due to overheating.
23 PSI - 1.6 Bar.
New Bearings for your DRZ400.
If you are in the lower end doing work, new bearings are cheap insurance for all that hard work.
This will not fit the DRZ400 kick start models. Nothing is available for the kick start models.
Replace your worn clutch plates and springs to reduce fade and slip.
A high quality cam chain from the folks at Wiseco. New cams, big bore kit, high-mileage motor, you might want to think about a new cam chain. Direct replacement for stock unit.
As the leader in innovation, design and development of aftermarket high-performance camshafts, Hot Cams is certain to provide the added boost that enthusiasts are looking for.
Designed, dyno proven and made in the USA, Hot Cams performance camshafts are one of the most economical, reliable and easy to install ways to add a 5-10% power gain to your bike.
Stage 1: These cams provide better low RPM torque, pulling power, and throttle response.
Stage 2: These cams will provide improved full throttle torque and horsepower starting at 4000 RPM and up.
Tech Notes: This cam replaces the 2047-1IN. It has better low RPM torque, pulling power, and throttle response. For best results it should be used with the #2050-1E exhaust cam. Uses stock DRZ400 valve springs.
All in one package.
We suggest adding a set of HotCams camshafts and a new clutch kit for the best results.
Stock bore replacement pistons from Wiseco. You have your choice of the standard compression ratio of 12.2:1, or a high-compression ratio of 13.5:1.
This high-compression kit will run perfectly with standard pump Premium.
Kits include piston, rings, wrist pin and circlips.
Includes three 9.48mm o.d. shims in each size from 1.20mm to 3.50mm in .05mm increments
Made from laser-cut, medical-grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area over many paper filters, catching debris down to 35 microns. The FLO filter pleat seam is welded and able to withstand up to 600 deg. F. Filter maintains consistent flow under all conditions including extreme heat, the presence of water and cold start-ups where paper filters can flow so poorly that they often cause the bypass valve to open and allow unfiltered oil to enter your engine.
This cleanable oil filter should be the last one you ever purchase.
Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
Grab our 5-pack and save both time and money!
Keep your motor running right with a fresh plug.
A Dual Electrode spark plug will last longer than a single electrode plug because the wear is shared between the electrodes.
E3 Resistor Spark Plugs
The unique design of the electrode maximizes the power generated by the spark plug through Diamond Fire technology. This electrode combines advanced performance capabilities and innovative technology to enhance the shape of the flame kernel. Consequently, the flame front ignites the air/fuel mixture more rapidly, accelerates heat transfer into the combustion chamber, and creates a more concentrated pressure front, facilitating a quicker pressure rise during the cylinder power stroke. The outcome is a more efficient combustion process and improved engine performance, making this a truly premium spark plug.
The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail/stop light function. 3 white LED's are used for license plate illumination. Included is a set of turn signal brackets that bolt to the mount. These are designed for a small signal with a 8mm mounting stud.
Lose that ugly stock taillight and license plate bracket and install this tidy one from ProCycle. We designed this unit and have it manufactured here in Oregon. Kit includes a LED taillight / brake light unit as well as compact turn signals. We also include splice connectors and split tubing, everything you need for this installation.
There is also an option to include matching front turn signals with side mount brackets that allow you to replace the clunky front signals with the same style as the rear in this kit.
These heavy-duty aluminum brackets are laser cut from 0.190" 5052 Aluminum then powdercoated black. Designed specifically for mounting auxiliary lights to the front of your DR650, the mount goes between the fender and the lower triple clamp. Longer fender bolts are included in each kit. installs in 10 minutes.
Three options are available: two different dual mounts that place the lights outside the fender and a single, center type mount. The 2" mount is for smaller type lights and is 8-5/8" between the mounting holes while the 3" is 10-3/8" between the mounting holes. If you are going to use larger style lights, the 3" mount is for you.
Note! The Dual 2" and 3" mounts do not work with the Acerbis 6.6 gallon tank! They make contact prior to full lock. Mounts are fine with other oversize tanks.
An aluminum Light Mount for your bike. Put whatever light you like up front for more light as well as great daytime visibility to other vehicles. Win-win situation. Choose the Single Mount or Double Mount.
B&B Off Roads Auxiliary single light bracket is made from 5mm 5083 structural plate. It was designed to suit a 6 " light bar. Add an auxiliary bracket and LED light to help Improve visibility whilst night riding.
Now available in the original version or the Ultra version. The original uses the front two emitters for low beam and then switches to the rear two emitters for high beam. The Ultra uses the front two emitters for low beam and then runs all 4 emitters on high beam at a reduced wattage. Wattage is 38 watts on low and 38 watts on high.
This bulb uses 4 Cree XHP 50 emitters, capable of more than 2500 lumens each. At 5000 lumens on each function, this is the brightest Cyclops H4 bulb.
*Universal part, Please check your application for fitment
This is a standard H4 bulb that has a 80 watt low beam and a 100 watt high beam. This is an easy lighting upgrade that should not over tax a stock charging system.
Make the Edge-2 Circuit Board installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. You will need a crimp tool or set of needle nose pliers to crimp connectors on.
This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.
Features:
This kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
The headlight features two primary sets of LED projectors, a wide low-beam pattern with distinct upper cutoff and a center spotlight high-beam for long range visibility.
The low-beam consumes 20W and remains powered when the 15W high-beam is fired. There is also a daytime running light feature which can be powered for additional glow. The LEDs are rated for 50,000 hours and operate at a 6000K color temperature.
No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.
Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.
Non-DOT
This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 1996-2020 DR650SE. No wiring, soldering, resistors, drilling, or fabrication required however due to the size of the headlight minor trimming on the backside of factory plastic headlight fairing is needed in non-visible areas.
Aircraft aluminum withstands hard hits from logs and rocks. All mounting hardware and wear blocks included.
Complete chain and sprocket replacement packages.
High quality steel front sprockets.
High Quality chain. Will need to be cut to fit your sprocket combination.
All of these chains come with a clip type master link.
Replace your lower chain roller with this high quality roller with 2 sealed ball bearings. The stock roller has no bearings. It's just a plastic wheel riding on a bolt. Ball bearing chain rollers are smoother, quieter and last longer.
Replace the wimpy stock DRZ400 Skid Plate made from 4mm thick 5083 aluminium plate. Strong and great looking. Leave the stock wings in place and give yourself something that will really stop any damage between the frame rails. Supplied with all the necessary stainless steel clamps and bolts required. Available in polished or with the heavy-duty black polymer coating. Like all he other B&B Bash Plates, these plates have foam or rubber where required to keep things a bit more quiet. This plate fits the E, S, SM & kick start models.
Clutch and Ignition covers made by B&B Eng. Formed from 2mm thick 5052 aluminum plate, selected because of its strength, corrosion resistance, excellent abrasion and impact protection. These will help protect your cases in the event of a bad fall.
These covers are attached to the engine cases with high quality heat resistance silicone adhesive
These covers will NOT fit early kick start only models that did not come standard with electric start. If you have added a kick starter to your bike that came with an electric start, covers will fit with no problem.
Protect your brake discs with high-grade aluminum alloy disk guards by Devol.
B&B Off Road Engineering Fender Brace is made to help support your front fender/guard. Also helps support and reduce fatigue from constant vibration.
Made from 4mm 5083 structural aluminum plate. If you wanted to carry a small tool bag this would be a perfect product to support the weight and strap the bag to.
Fits on top of the fender and bolts between the fender and bottom triple clamp. Requires you to drill one hole in the fender for mounting.
A stainless steel front fender brace. Helps stabilize your front fender.
Gives additional strength for carrying a fender mounted tool bag.
Fits on top of the fender and bolts between the fender and bottom triple clamp. Stainless steel won't rust or corrode. Includes hardware.
Requires you to drill one hole in the fender for mounting.
High-quality, direct replacement plastic kit includes:
Yellow kit is only available with white side covers
Add-on Headlight cowling fits S and SM models not "E" offroad model
Genuine Suzuki super moto fender. A perfect match for the original gray plastic.
Front fender from ProCycle Plastics (formerly DSA) is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does. Vacuum molded, these are a design improvement over stock. These are fully compatible in any combination with the original factory plastic.
OEM Suzuki headlight cowling.
Molded using a very durable, lightweight 1/8" thick polycarbonate - giving the windshield a high impact strength and making it shatter-resistant with a superior light transmission quality. Mounts quickly and easily onto the stock headlight cowling for a clean factory look. Drilling of the cowling is required, hardware is included. Removal for trail riding is also quick and easy.
Only Clear screens are available at this time.
Made of military aircraft grade 3/16" cast acrylic, this guard will protect your lens from roost, rocks and branches. Optical clarity of the acrylic ensures brightness and projection of your headlight are minimally effected while all the while protecting your headlight from impact and abrasion.
Guards are held to the headlight lens with an industrial strength hook and loop system on each corner.
Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists and then anodized black.
The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary hardware is included.
Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets.
Replacement shift lever from IMS with folding tip.
These tips are for the Warp 9 Shift Levers only.
These are held to the cast Warp 9 lever with a pin and e-clip making them easy to change out. Includes new pin and e-clip in case you lose yours.
You can also order just a new pin hardware kit which comes with new pin and clip.
Original Suzuki factory replacement levers for your DRZ400S/SM/E
A quality replacement speedometer cable from Motion Pro.
Suzuki makes it almost impossible to replace your stock grips. It's much easier with a new throttle tube.
Ease the pressure on your wrist during those long highway drones out to where the fun begins. ProCycle has developed this kit that includes a Vista-Cruise throttle lock, a specially modified alloy throttle tube and an anchor plate that attaches to your throttle housing. Just flip the thumb lever down to apply enough friction to hold the throttle in place. Use the supplied longer screw to attach the anchor plate to your lower throttle housing bolt hole. Also included is a tension adjustment tool that you can keep on your key ring. Keep the applied tension lightly adjusted so it's easy to roll the throttle off.
Fits bikes with dual cable throttle housings.
The headpipe gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head, thereby making them a single use part. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
The muffler joint gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers (Q4 or PowerCore 4) do not require a joint gasket but the all other aftermarket mufflers as well as the stock muffler do require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.
The V2 Series Slip-On muffler features an aluminum body, TIG welded components, stainless steel inlet tube and a great new look. This Lightweight Slip-On weighs approximately 5.5 lbs.
The DG Performance systems offer increased throttle response, power and torque. Standard sound level is approximately 98 db. Equipped with a US Forestry approved spark arrestor.
Yoshimura RS-3 that will slip right on to your stock header. Made by hand to the highest quality standards using the championship-winning racetrack experience and their extensive R&D facility ensure these pipes perform and will last.
Both full systems and slip-on mufflers include 96 dB sound insert/USFS approved spark arrestor installed in the muffler. Mid-pipe is stainless steel while the stainless RS-3 oval muffler design has a slim profile with an aluminum end cap.
Works on OEM header only!
The Q4 employs intricate chambers, baffles and proprietary multistage packing material making it the best performing quiet muffler available.
Constructed from aircraft grade aluminum and high strength stainless steel.
Sound output 96dB. Several pounds lighter than the stock muffler.
Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Unit is pounds lighter than stock and gives gains in horsepower and torque throughout the RPM range. All of that in a package handmade in the USA with a 1 Year Limited Manufacturers Warranty.
The RS-4 Twin Pipe kit was previously only available as a custom system for Kevin Schwantz.
Yoshimura is offering these incredible "Twice Pipes" which are completely fabricated by hand and TIG welded to perfection. They certainly sit at the high end of what is available for the mighty SM... The pipes have a stainless steel header and "Y" pipe mated to twin carbon fiber or aluminum RS-4 mufflers for incredible looks and performance. The kit also comes with a custom Yoshimura side stand.
Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Head and mid-pipe are constructed from 304 stainless steel. Entire unit is pounds lighter than stock and gives great horsepower and torque gains throughout the RPM range.
All handmade in the USA with a 1 Year Limited Manufacturers Warranty.
These thumb-screws replace the stock headlight adjustment screws. These adjusters make it much easier to keep your headlight aimed properly. This is even more important if you are running the HID headlight as it is very easy to dazzle oncoming traffic if your headlight isn't aimed correctly.
Here's an easy way to add a Tach to your motorcycle.
More range at a great price.
The 3.6 gallon tank is for the off-road DRZ400 and DRZ400E.
The 3.9 gallon tank for the dual-sport DRZ400S. The 3.9 gal tank also fits the ES and SM models.
Both tanks are available in a selection of colors.
NOTE: Clarke tanks do not come with a vent hose or vent cap.
Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.
Available in multiple color choices. Choose Natural if you wish to easily see the fuel level of your bike. 4.0 gallons.
A popular upgrade from the stock vacuum operated fuel valve. Manually operated. Must be shut off any time the bike is parked for more than a few hours. Fits stock tank or aftermarket tank and has both main and reserve. Fully rebuildable.
This CNC cap will replace the stock gas cap on the stock tank. You do need some parts from the stock cap, so don't throw it away yet! It is not difficult and this kit includes the additional hardware required. Also included is a vent tube with a matching cap.
For use on STOCK TANK ONLY! This is NOT a locking cap.
Does not fit California model DR650
A replacement gas cap for your IMS tank. Newly redesigned to resist damage from new fuel additives that were hard on the seal in the old style cap.
Moose Racing Adventure seat provides improved comfort for your riding adventures, or just commuting around. You choose between the stock seat height, or a low seat height (about 1 inch lower). The durable micro-fiber suede top cover enhances rider comfort and increases stability. Side gripper panels ensure secure seating during aggressive maneuvers. The cover is constructed from smooth marine-grade vinyl and features an embossed Moose Racing logo. It includes a strap kit that enables secure attachment of cargo to the pillion section of the seat.
State-of-the-art replacement seats, Sargent seats are built on a percision-molded lightweight Polytec seat pan. Sargent's proprietary seat foam (Super Cell Atomic Foam) is their own unique blend of resilience, firmness, and vibration-absorption qualities, making it well suited for long distance comfort and support. Sargent seats are covered in a marine-grade, UV-stablized mildew resistant CarbonFX vinyl. These seats will fit bikes with the stock, IMS, or any other aftermarket fuel tank.
Billet aluminum lowering links. Lowers the rear suspension.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Complete high quality kit to replace the bearing and seals in the DRZ400 swingarm pivot.
Race Tech shock springs in a wide range of spring rates to dial in your rear suspension to suit your weight (stock spring is 5.3 kg/mm). Recommended spring rates:
| Rider Weight w/gear lbs. | Spring Rate |
|---|---|
| 100 or less | 4.6 |
| 100-124 | 4.8 |
| 125-149 | 5.0 |
| 150-174 | 5.2 |
| 175-199 | 5.4 |
| 200-224 | 5.7 |
| 225-274 | 6.0 |
| 275 + | 6.3 |
Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.
DRZ400 E/S
A pair of Race Tech fork springs to dial in your front suspension to suit your weight.
Fits all DRZ400 models with conventional forks (not for SM)
Recommended spring rates:
| Rider Weight w/gear lbs. | Spring Rate |
|---|---|
| 90 or less | .42 |
| 90-119 | .44 (stock) |
| 120-150 | .46 |
| 150-180 | .48 |
| 180-220 | .50 |
| 220-250 | .52 |
| 250+ | .54 |
For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.
The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.
Helps protect vulnerable fork tube and seal from dust, dirt, and corrosive elements. Hook & loop (Velcro) fastening on back side makes installation or removal for cleaning a breeze.
Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers
Twin Air Filter's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
The air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air-the #1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow.
Dynojet Jet Kits increase power and smoothness throughout the entire rev range, while maintaining optimum fuel economy. Each Dynojet Jet Kit includes comprehensive instructions which show step-by-step installation and testing procedures to ensure a perfect setup every time.
Dynojet Jet Kits increase power and smoothness throughout the entire rev range, while maintaining optimum fuel economy. Each Dynojet Jet Kit includes comprehensive instructions which show step-by-step installation and testing procedures to ensure a perfect setup every time.
This kit is for the 36mm Mikuni CV carburetor and includes 2 Needles that have been developed by JD Jetting and manufactured for them to their exacting specifications. These two needles allow a wide range of tuning possibilities and provide correct fuel delivery at any throttle position.
4 allen type screws for the top of the carburetor are also enclosed should you strip out the stock screws during your tuning process. Complete instructions with photos, jetting suggestions for different set-ups and situations, 5 Main Jets, a Pilot Jet and a drill bit complete the package.
Repair kit comes with everything you need to get your carb back in shape.
All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.
Made by Nissin, an OEM supplier in Japan
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Need to remove your clutch assembly? This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub. Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut easy. All of that and no worries about doing any damage to your expensive clutch hub.
Your automatic cam chain tensioner is spring loaded. This can make it difficult to install as it wants to extend before you have it bolted into place. This handy tool will back off the cam chain tensioner mechanism and hold it for you. No more awkward 3-handed contortions are required to get the tensioner installed.
Shield your bike’s vital drivetrain components with B&B Off Road’s heavy-duty front sprocket case saver. This premium guard, CNC-machined from high-strength 6mm aluminum plate, offers unparalleled protection against rocks, impacts, and other off-road hazards.
Uncompromising Strength, Precision Fit:
Engineered for maximum durability, this case saver boasts a 6mm main body crafted from 5083 structural aluminum – a material renowned for its resilience. Complementing this robust core is a 4mm thick front sprocket cover, ensuring comprehensive protection for your drivetrain.
Designed for Flawless Performance:
CNC machining guarantees a precise fit for both Suzuki DRZ400 (2000+) and Kawasaki KLX400 (2000+) models. This ensures seamless integration with your bike, eliminating concerns about interference or compatibility issues.
Peace of Mind on Every Ride:
Whether you’re navigating technical single tracks or powering through dusty plains, this case saver offers the confidence to push your limits. By safeguarding your front sprocket and surrounding components, it minimizes the risk of costly repairs and keeps you on the trail.
A set of six high quality grade 10 sprocket bolts with lock nuts. Thread-lock compound has already been applied for extra security.
These bolts are flat head style, requiring a countersunk hole in the sprocket.
This anodized billet piece, brings a touch of color to your bike. Available in red or blue, it replaces the stamped steel clevis that connects your brake pedal to the master cylinder.
Your choice of an aluminum bolt-on foot pad or a steel weld-on unit. Each will make the footprint of the stock side stand considerably larger, preventing your DR from tipping over in soft terrain. The bolt-on unit is cut from aluminum and then powder coated black, it comes with stainless steel mounting hardware.
The bolt-on pad and does require use of a drill for installation. The weld-on pad will need to be welded to the stand and then the entire unit painted for corrosion protection.
A 10-pack of drain plug sealing crush washers. Replace your sealing washer at every oil change to prevent a leak.
Extra protection for your motor! Strong magnet at the end of the plug picks up ferrous metallic flakes in your oil, protecting your engine!
It is a good practice to replace your sealing washer with every oil change. These 10 piece kits are made up of 5 Copper washers and 5 Aluminum washers. The manufacturer recently decided to make half of the kit Copper washers as that is the material of choice for many OEM manufactures. This gives you the opportunity to decide which you prefer, but either will work great at creating a leak-free seal between the case and the drain plug.
With this upgrade, you can avoid having to keep new replacement cotter pins on hand every time you adjust your chain.
*Black front fender with various superficial scratches on the top of the fender. Sold as is.
Front fender from DSA Concepts Plastics is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does. Vacuum molded, these are a design improvement over stock. These are fully compatible in any combination with the original factory plastic.
