Search Products

Plug-In connector kit for your CRF. This kit fits Rally and Non-Rally Versions of the Motorcycle. Wires and terminals will come pre-attached with subharness.  

Plugs into the Aux Power connector. 
Harness length is 32" (2.66ft)

The Bag Snake kit works great for rear bags and side bags. When rigged with a side bag the second ring on the ring tensioner creates a secondary buckle so you can loosen the top for access and your bag doesn't fall away from the bike.

When rigged for a rear bag the diagonal section of the strap prevents any slippage over the ends of the bag. For this reason, the Bag Snake is great for smaller rear bags.

Kit Includes:

• 1 Heavy Duty Cam Tension Loop
• 1 Heavy Duty Metal Ring Tension Loop
• 1 Six Foot Runner Loop
• 1 Heavy Duty Metal Ring Loop

These flat tie down 'stretch' straps are designed specifically for motorcycles, ATVs and snowmobiles. Carry anything on your motorcycle securely and without scratches with these flat - no hook - tie down straps.

ROK Straps are a two-piece strap with a quick-release buckle in the middle and loops on each end. One end of the strap is a heavy duty nylon, the other has a strong stretchable section. Instead of hooks that can slip or come undone, ROK Straps have a loop sewn in each end. you pass the buckle around your frame, rack or other secure point and then back through the loop in the end making for a very secure mount. With each end secured, connect the buckle in the middle and simply tug the slack end of the strap until your load is firmly held in place.

• Smartly designed to accommodate, but not limited to: 1 gal. - 1.75 gal. Rotopax fuel/water packs, Wolfman Luggage - Wolf Tail bag (M303), and Givi Monokey top cases (separate mounting kit required)
• Large 14.5"(Width) X 13"(Length) luggage platform
• CNC laser cut from 1/4" 5052 Aluminum - weighing only 2lbs. 10oz.
• Each rack is sand-blasted and sprayed with a premium DuPont semi-gloss mini-tex powder-coat finish
• Stainless hardware kit and installation instructions included
• All materials and craftsmanship are sourced 100% in the USA
• Carrying capacity is 20lbs.

PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash. 

Sold as a pair.  Easy to Install

• Complete with all necessary mounting hardware
• Fabricated with 1/2 inch steel tubing, MIG welded
• Finished with a semi gloss black industrial grade powder coat
• Comes with left and right side racks, each side weighs 2 lbs
• The TW200 side racks are intended to work hand in hand with our ENDURO Series rear rack.

Nomadic Rack for the TW200. CNC laser cut from 3/16" 5052 aluminum with a large 12 x 10-7/8 mounting surface area. Sand blasted and then powder coated black to give it a shot peened look. This rack is an easy installation with a 4 point mounting system with no modifications required. There are multiple strap slots for securing gear bags and cargo. Doubles as a grab handle or tow bar. Is compatible with RotoPax mount. All hardware and instructions included.

You may purchase just the rack or you can order the Rack with the RotoPax Mount. If you really want it all, you can order the Rack, Mount and a Fuel or Water Container.

• Powder coated black (shot peened look)
• Fully welded construction
• Rigid 4 point mounting system
• Hardware and detailed instructions included

The Nomadic Rack is a favorite for dual-sport riders with ruggedness and ease of installation. This rack does not need to be removed for under-seat maintenance. The mounting area is large 11" x 10" and the rack weighs just under 3 lbs. It constructed of 16 ga. steel and fully welded, then powder-coated black with a shot-peened look. Has a rigid four point mounting system and doubles as a grab handle. Complete instructions and stainless steel hardware are included.

• CNC laser cut from light weight 1/8" 5052 Aluminum
• Easy installation, no modifications required
• Large 12" x 9" surface area
• Sleek low profile, and lightweight!
• Rigid 4 point mounting system
• RotoPax 1 gal or 1.5 gal compatible

You may purchase just the rack or you can order the Rack with the RotoPax Mount. If you really want it all, you can order the Rack, Mount and a Fuel or Water Container.

Secure storage of a spare tube, tire irons, or random miscellaneous items is a must for any trail ride or adventure. The OBR ADV Gear Fender Bag is constructed from a heavy duty industrial grade ballistic fabric that secures tightly to any fender via oversized heavy duty gutter hooks. The OBR ADV Gear Fender Bag also utilizes an optional double button snap system that when used eliminates any potential for shifting of the fender bag when riding off road or over rough terrain.

Features

• Heavy Duty industrial grade material construction with high strength UV resistant nylon webbing
• Heavy duty dust resistant #10 coil zipper with cover flap 
• Secure attachment with oversized heavy duty gutter hooks
• Optional secondary button snap retainment system
• Sized to fit most HD 18” or 21” tubes

The little tool bag that Yamaha provides behind the side cover is nice, but adding this Tool Tube to your TW will make it easier to carry some real tools! The ABS pipe is plugged on each end with waterproof expanding plugs. It is held to the frame of your TW with powder-coated steel straps and brackets. It provides a storage space of 3" ID x 10-1/2" long. Includes all hardware required to mount to your TW200.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 3 strong powder coated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approximately 13" long.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

More range at a great price. Choose  the 2.7 gallon tank for the KLX250S in Black, Green, Natural or White.

  This tank will NOT fit the 2009-2015 models.

All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.

The Warp 9 shift lever is black anodized and the Warp 9 logo is laser etched into the finish. The black anodized knurled aluminum tip is folding and returns via a stainless-steel return spring. Includes the pinch bolt as well.

The tip is replaceable in the event of damage.

Order up your new levers here! If you keep breaking levers, you might want to think about a set of hand guards to protect them in case of a fall.  

These are genuine factory Yamaha replacements.

Folding tip, forged aluminum shift lever from BBR Motorsports. Stronger and lighter than the stock shift lever.

• Strong forged aluminum construction
• Steel knurled folding tip (chrome plated)
• Anodized titanium finish
• 1/2" longer than stock

Warp 9 has created a beautiful brake pedal machined from billet aluminum to an 8mm thick work of art. A stainless steel pin eliminates wear in the frame. This pedal has the ability to move the spring loaded brake tip 10mm either way from the center position. The arm is arched to provide clearance for riders who have the lowpeg + centerstand combination.

Direct replacement cables for your T-Dub. OEM or high-quality replacements will keep you on the road or trail. Pay attention to the model year for correct fitment, then select the cable type: Throttle, Clutch or Speedo, they're all here.

Quality replacement clutch cable.

• Nylon-lined housings and precise OEM component dimensions

• Adapt 7/8" bar mounts to accept oversized 1-1/8" handlebars
• An economical alternative to replacing expensive top triple clamps
• Include mounting bolts.

DRZ400 E/S

A pair of Race Tech fork springs to dial in your front suspension to suit your weight.

Fits all DRZ400 models with conventional forks (not for SM)

Recommended spring rates:

Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.

Both kits include all bushings, snap rings, and washers.

Gen 2 kit also includes the necessary O-rings.

Gen 1 kits are OEM bushings, snap rings and washers.

Genuine Yamaha OEM Replacement airfilter.  Designed to increase horsepower and acceleration while providing excellent filtration.

Twin Air's high quality materials and superior construction deliver unbeatable performance and protection. The hands-down choice of more World and National Champions than all other filters combined.

Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles without restricting airflow.

Comes with everything you need to freshen up your carburetor.

This is an O.E. replacement diaphragm for your BST40 carburetor.

Genuine Keihin spring, washer, and oring for the fuel screw of FCR and FCR MX carbs.

Just the parts…
Fuel screw spring, washer, o-ring (fuel screw not included)

• Complete kit from Moose Racing to rebuild the OEM carburetor
• Each kit contains all necessary gaskets, O-rings, float valve and jets
• Supplied to Moose Racing by the same supplier the OEMs use

This kit is for the 36mm Mikuni CV carburetor and includes 2 Needles that have been developed by JD Jetting and manufactured for them to their exacting specifications. These two needles allow a wide range of tuning possibilities and provide correct fuel delivery at any throttle position.

4 allen type screws for the top of the carburetor are also enclosed should you strip out the stock screws during your tuning process. Complete instructions with photos, jetting suggestions for different set-ups and situations, 5 Main Jets, a Pilot Jet and a drill bit complete the package.

Geared for the do-it-yourselfer that already has a TM40 or HS40. This kit supplies everything you need to convert it for use on your bike.

Kit includes intake and air boot adapters, throttle cables, choke knob, accelerator pump nozzle, a wide selection of main and pilot jets plus a TM40 tuning manual.

OEM Suzuki headlight cowling.

Quality replacement headlight fairing for TW200

Formerly DSA, now ProCycle brand, is a plastics kit in three colors - Black, White, and Blue, as well as Blue fenders with White side panels and Black fenders with White side panels. (headlight cowl not included).

Vacuum molded, these parts are a design improvement over the stock pieces. The side panels have a crisper, more angular look than the stock parts while the front fender is shaped like the DRZ400SM OEM front fender. Big enough to be functional without wind-steering the bike like the stock fender does.

Kits include front and rear fenders, a new LED tail/brake light and license plate holder, and both side panels.

Add a fresh new side panel hardware kit and an adhesive heat shield for a fresh off the showroom floor look.

Add a stock Suzuki headlight cowl if you are doing a complete color change to your DR (must select plastic kit with head light cowl option)

Freshen up the look of your TW. New Plastic in Black or White. Includes Rear Fender, Side Panels, Headlight Cover, and Front Fender.

Choose a Kit with OEM Front Fender or after market SuperMoto fender.

SuperMoto fender kit includes our High Mount Fender Bracket!

Transform your ride. MadStad's patented mounting system allows riders to adjust the height and angle of their motorcycle windshield resulting in much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide. Better still, this dual-sport version pivots the shield down and forward to get it out of your way for off-road riding!

What's included in the kit:
Their complete bolt-on system is custom-made for your bike and includes everything needed to mount and position the shield. Your bike will not require any modification.

• A set of MadStad adjustable dual-sport brackets
• 3/16" (4.5 mm) thick cast acrylic windshield.

The MadStad brackets bolt to the top of your fork clamps and are completely free of the handlebars. You can adjust the shield for the optimum height, angle and airflow for comfortable street and highway riding. When going off-road you can leave your comfort adjustment as-is and pivot the entire system down and forward in front of the headlight so you can get it out of your face completely. When it comes time to hit the pavement again, simply pivot it back up and you are back in street riding comfort mode.

Zero Gravity windscreens feature the finest optics of any windscreen on the market. All Zero Gravity windscreens are fabricated using highly specialized "vacuum forming" techniques similar to those used to form aircraft canopies. The result is a virtually distortion free optical lens.

Made from the finest grade of acrylic plastic, Zero Gravity windscreens are stretched as they are formed, a process which results in superior strength and flexibility. This flexibility allows the windscreen to absorb road vibrations and resist cracking. All of our windscreens are factory pre-drilled and ready to install. The mounting holes and windscreen profile match the O.E.M. windscreen for a precision fit.

Zero Gravity currently offers three types of windscreens for the new version of the KLR.

SR is the Stock Replacement

DB is the Double Bubble screen

ST is the Sport Touring model.

The DB model is approximately 1.75 inches taller than stock and the ST is approximately 3.5 inches taller than the original. Each screen is available in Clear, Smoke or Dark Smoke colors as well.

This is the brace needed to stabilize the big front fender on the XR650L. This simple bolt-on brace reduces wind buffeting at highway speeds. It also helps carry the weight of a fender mounted tool bag.

Made from laser cut 5052 aluminum, then CNC formed and beautified with a shiny black powder coat. Easily mounts in a few minutes using the included hardware.

New replacement side panels specifically made for TW200.

Sold in pairs, designed to be used with Maier USA Rear Fender.

Universal off-road front fender. Must be drilled to fit your mounting bolt pattern.

Made from laser cut, medical grade, 304 stainless steel micronic filter cloth. This filter provides 200% more filter area than most other filters. Most high quality filters will pass particles in the 90 to 95 micron range, and some tested, as much as 300 microns. Sand is about 125 microns and a white blood cell approximately 25 microns. Scott's stainless filter catches items down to 35 microns "absolute". The pleat seam is welded, not glued like paper filters, increasing temperature resistance to 600 degrees F.

This is all you need to not only change your oil, but protect your motor as well. We include a magnetic drain plug in the standard kit, to help catch stray metal pieces, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

This is all you need to not only change your oil, but protect your motor as well. We include a billet oil drain plug cap, a 5-pack of oil filters, and new O-Rings to replace any you have that may be leaking or worn.

• Billet Oil Drain Plug Cap
• O-Ring Kit
• 5-Pack of Oil Filters

Includes forged JE 89mm piston 10.5:1 piston, Rings, Clips, Pin, big bore sleeve and top end gasket set. You will have to have the big bore sleeve installed in your cylinder and bored to fit the larger piston.

Generator cover gasket to seal up the cover once you have your new Doohickey in place. New OEM gasket. What else can we say? If in doubt, put in a new one.

A high quality top end gasket set for the XR650L

Complete set of friction plates, HD springs and steel separator plates prevent premature driven plate wear, oil muddying and loss of stack height. Built with swaged aluminum carriers that spread the load on the clutch basket and prevent clutch basket "dogging". Anti-swell, alloy impregnated heavy-duty facings for smooth clutch action. Allows modulation, unlike paper clutches which tend to snatch. Don't forget to add a fresh gasket.

Heavy-Duty clutch springs

• 15% stiffer than original
• Minimize clutch slip
• Reduce plate wear
• Improve power to ground

Iridium spark plugs are made with premium quality materials.

Iridium plugs last longer than standard ones, meaning you won't have to replace them as often.

• The ultimate in the evolution of spark plug technology and performance from an industry leader
• The iridium electrode is 25% smaller than a platinum electrode, and it's just 1/4 the size of a conventional nickel electrode
• Ultra-small diameter center electrode reduces voltage requirement and extends ignition system life
• Metal shell plating has enhanced anti corrosion qualities

Sold individually, unless otherwise stated.

To fit tapered 28.5mm (1 1/8") handlebar.

• Barkbusters strongest handguard EVER!
• Designed for Enduro and Trail bikes.
• Two mounting points secure the full wrap around aluminum design.
• Compact curved profile to protect hands and levers during intense trail and tight bush riding.
• Heat treated aluminum backbone for maximum strength.
• Replaceable, high impact resistant EGO plastic guards included.
• Large range of colors matched to popular motorcycle brands.
• Deflectors available for increased protection (sold separate).
• Easy installation.
• Note: Not ideal for bikes with long clutch and brake levers.

NOTE: will not fit Renthal Twin Wall or Barkbusters VSBar.

Replacement handguards for your Cycra set up. Injection-molded high-impact plastic replacements. Includes all hardware needed for mounting.

X3 EVO represents the off-road evolution: LeoVince has combined all its experience in the off-road world with cutting-edge materials and Italian design, enhancing freedom in its purest form.

The X3 EVO body is made of AISI 304 stainless steel with TIG welds handcrafted by specialized operators, to guarantee long-lasting performance. X3 EVO will allow you to face the most extreme environments and conditions because it does not fear water or mud, nor wear over time.

The LV logo is their tribute to a motorcycle culture that we have loved for 70 years and is laser etched on the body of the exhaust: it is as endless as their passion.

They manufacture the end cap in 100% real carbon, with their special 2x2 twill carbon fiber, specifically designed to resist high temperatures and make the X3 EVO even lighter.

The matte clear coating, in addition to enhancing the carbon texture, protects the end cap from wear and UV rays, keeping the X3 EVO always in a perfect shape.

The sound of X3 EVO is already unmistakable at low revs. X3 EVO has a direct interior, specially conceived to channel the exhaust gas in an optimal way, to unleash a deep sound, giving a new voice to your bike.

The X3 EVO's Spark arrester has been tested and approved by the United States Forest Service and is essential for off-road riding in compliance with regulations, with more peace of mind, more respect for the environment and more fun.

Since Kawasaki brought back the popular little KLX250 with updated fuel injection, Yoshimura brought back an updated RS-2 slip-on that now incorporates an o2 sensor that accommodates the new fuel injection technology on the KLX. All of that with added power, torque and that distinct Yoshimura exhaust note.

Entire unit is proudly made in the good old US of A to boot!

• Diamond-shaped sleeve
• Large core and increased muffler packing volume means quieter operation
• Stainless steel cone end-cap
• Stainless steel tail-pipe
• 2.8 lbs. lighter over stock unit.
• Comes with USFS Approved Spark Arrestor

The product that you are purchasing is designed and intended for closed course competition use only and is labeled as such, i.e. Yoshimura "RACE SERIES." Yoshimura RACE SERIES products are neither designed nor intended for use on PUBLIC ROADS or LAND. Such use is prohibited by Federal and State regulations.

Protect your head pipe from rock damage. This stainless steel spine clamps to your head pipe to add a layer of protective armor between your vulnerable pipe and those nasty rocks or logs. Fits the stock headpipe. Will fit the FMF head pipe with the addition of larger clamps.

This is a genuine Suzuki part. We recommend installing a countershaft seal retainer to prevent the countershaft seal from popping out while riding.

Slime Tube Sealant is formulated and tested for use in all tube tires. Once installed, Slime remains liquid and will not harden or dry out. Slime is guaranteed for 2 years.

As the Slime treated tube rotates, centrifugal force pushes the sealant to the tread area creating a layer of protection, repairing punctures as they occur and treating existing punctures. Slime is not intended for use in tubes losing pressure from sidewall punctures, bead leaks, damaged rims or faulty valves. Slime for tube type tires is not recommended for use in tubeless tires.

• Prevents and repairs punctures up to 1/8"
• Remains liquid inside the tire, coating the tread area as the tire rotates
• Non-toxic, non-hazardous, non-flammable, non-aerosol and water soluble
• Tubes treated with Slime can be patched with a conventional vulcanized patch using a bit of patience and care

Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.

This set of high quality replacement steering stem bearings includes:

• Upper and lower tapered bearings
• Upper and lower bearing races
• Upper and lower seals

The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option. 

Wider foot pegs for sure-footed comfort. 

17-4 cast stainless steel.

Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm. Lo-pegs are down and back 1/4".

Inexpensive way of getting the factory look. Adds 1/2" of width to any standard foot peg. These will give you a much more stable platform when standing on the pegs.

Sold in pairs.

T-Rex stands are made from steel tubing finished in black powder for durability. Back by a 3-Year limited warranty for any material or manufacturing defects. Rest assured that you are getting best material commercially available.

Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools.

The basic purpose of a center stand serves to enhance ownership experience by easily raising the rear wheel completely off the ground for drive chain lubrication and adjusting, tire & tube patching/replacement and even FRONT wheel work. Those fortunate enough to have owned a motorcycle equipped with a center stand have come to learn the game-changing role it can play -even off-road.

Center stands have many more inherent uses including:

• Increased stability when parked on soft ground
• Easier cleaning and pre/post ride inspections due to the upright positioning
• Less effort required to place on its stand when compared to a milk crate or portable stand
• Superior parking/storage advantages in tight spaces

Unlike a basic portable moto stand, your center stand is ALWAYS available wherever your need it, whenever you need it.

When in use, this kit raises your rear tire 3/4" off the ground. When retracted, the stand tucks away, 100% unobtrusive to the rider and passenger. A robust retention spring ensures the stand remains retracted, even on the roughest trails.

Each kit comes with all hardware and detailed instructions. All parts are powder coated black with a fine texture

High quality sprockets

• Stock size is 14 tooth
• Add teeth for highway riding
• Subtract teeth for low end gearing

Counter shaft sprocket replacement requires the removal of the left side case cover. A new gasket may be required. This is also a great time to replace that leaking oil seal!

Now you can have minimum output shaft wear, minimum chain drive wear with the FRITZCO DRIVELINE sprocket. The design of their sprockets provide correct chain alignment, allows for full spline contact with the XR650L's output shaft, fit the counter shaft either way, and straight up no hassle installation with the OEM two bolt retainer and fasteners (except 13 tooth that comes with it's own quick change retainer). Their sprockets are machined from alloy steel that is comparable in every way to OEM Honda and the best offered by other manufactures. The sprockets are then given a heat treatment that provides a compatible sprocket for the Honda output shaft and longest wear life possible.

A way to double the sprockets life would be to have a sprocket that fits on the shaft either way so both sides of the teeth can be used. Bear in mind you can't wear one side of the teeth all the way through, then flip the sprocket, and expect double life. You must reverse when a normal wear pattern develops.

16 tooth sprocket is the biggest front sprocket that will run with the standard 110 link chain and 45 tooth rear sprocket on an XR650L
The OEM cover will require modifying to use the 16 tooth sprocket on your XR650L.

High quality steel rear sprockets from 39 to 53 teeth.

Sprocket color may differ depending on size.

High Quality chain. Will need to be cut to fit your sprocket combination.

Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.

With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way. 
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.

The Swiftkicker is 100% manufactured in the USA from the highest quality components. 
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.

Measured from the center of the pivot to the bottom of the foot.

• Standard length travel range is 13.5"-19.5" (the middle of the travel is approximately the same length as the stock stand)

Ride in warm temperatures a lot? Worried about your motor oil just getting too hot? The Trail Tech Universal Fan Kit mounts up to the backside of the DR's oil cooler to draw cool air across it and keep those oil temps down. An electronic temperature sensor mounts to the fan, no need to cut any fluid lines, and automatically turns the fan on when needed to keep the temperature in the optimum range.

The activation sensor can be set wherever you like to keep the temperature right where you want it. Backlit for easy viewing anytime it also includes a volt meter.

Kit Contents

• 4 inch SPAL fan
• TTV Temp Meter
• Temperature Sensor
• Complete Wire Harness

A complete kit to mount your phone (or other electronic device) to your motorcycle. The universal cradle expands from 2.25" to 3.25" wide and 4.75" to 6.25" tall. The width is adjustable but fixed while the upper portion of the cradle is spring loaded to keep your device secured in the roughest conditions.

Select the mount option that works best for you. The mirror mount is shown in the photo at left and is a flat plate with an 11mm hole on one side and a RAM ball on the other. Simply remove your mirror, place the plate between your mirror and the perch and tighten it down.

The handlebar mount kit allows you to mount to either a 7/8" or 1-1/8" bar. Also includes hardware to mount to the back of a lever perch. See image at bottom middle for kit pieces.

The X-Grip with handlebar mount is best suited for larger phones up to 4.5" wide. The spring loaded X-Grip cradle expands and contracts, allowing for a perfect custom fit. Kit also includes a device tether recommended for outdoor applications.

When upgrading your Suzuki DR650 with LED turn signals, it's required to install a diode module to prevent all of the signals from blinking at once regardless of left or right signal activation. Some riders choose to splice and solder their own solution, but we like things plug and play. That means all you have to do is plug in the TST kit and you're done! There's no need to cut or splice your OEM wiring harness or break out the soldering iron and electrical tape.

• Plug and play installation - meaning no cutting, splicing, or soldering
• Eliminates issue of all signals blinking when activating only one side of turn signals
• Enables power to flow in single direction from LED turn signals to the dash indicator
• Does not fix hyperflash (LED turn signals flashing faster than OEM specified rate)
• (1) TST Plug and Play Diode Module
• 1 Year Warranty 

This relay will fix your flash rate problem caused by aftermarket signal lights and/or integrated tail light. If your signal lights flash too fast or do not flash, this part is your solution! Plug and play - easy installation.

Only ONE relay is needed per motorcycle.

Features

• Slows signaling flash rate back to the normal rate when your bike goes into hyperflash state (or your signals stay on constantly)
• Plug and play installation: simply replaces the relay already on your bike
• Fits like OEM

This component works with the following signal configurations:

1. All stock
2. Stock taillight, aftermarket signals
3. Integrated taillight, stock signals
4. Integrated taillight, aftermarket signals.

This heavy duty aluminum bracket is specifically designed for mounting auxiliary LED lights to the front of your XR650L without interfering with your large aftermarket fuel tank.  If your bike needs improved lighting this mount is the best place to start!

– 0.190″ 5052 Aluminum
– Laser cut
– CNC formed
– Powder coated black
– Includes stainless mounting hardware and JNS stickers.

LED auxiliary lights are sold separate.

Modern LED technology with a classic look!

This plug & play kit is built around the all new Holley RetroBright LED headlight which comes in three different colors.  

Choose from Classic White (3,000K), Modern White (5,700K), and Euro Yellow.  The RetroBright also features a replaceable bulb.
 

Low Beam: 25W, 2,000 Lumens
High Beam: 30W, 3,000 Lumens
Color Temperature: 3,000k or 5,700k
DOT Compliant
Beam Pattern: Left Hand Drive (USA)

This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a plug and play installation however a small amount of trimming on the backside of the plastic headlight shroud is required.

This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive). The high beam is amazingly bright eliminating the need for auxiliary lighting.

The materials, construction, and aesthetics are all top notch. You won’t be disappointed.

Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive

Now available in the original version or the Ultra version. The original uses the front two emitters for low beam and then switches to the rear two emitters for high beam. The Ultra uses the front two emitters for low beam and then runs all 4 emitters on high beam at a reduced wattage. Wattage is 38 watts on low and 38 watts on high.

This bulb uses 4 Cree XHP 50 emitters, capable of more than 2500 lumens each. At 5000 lumens on each function, this is the brightest Cyclops H4 bulb.

• All metal construction for bases and collars
• Better thermal efficiency 
• Better beam pattern distinction between high and low beams
• 5600k
• 38 watts 
• Removable metal base plate for easy install.
• Screw on connectors at driver
• Standard H4 connector
• High/Low Beams

*Universal part, Please check your application for fitment

Here is another great upgrade for the TW200 or the VanVan front tire.

Universal 'old school' trials type tread pattern. A versatile performer with a tough nylon carcass and raised dimpled knobs that work well in a variety of terrain.

• Narrow knobby configuration means less of an environmental foot print on the trail
• 4 ply rated
• DOT approved
• Not intended for extended highway use

Tire size is 4.00-18 (64P load / speed rating)

From Shinko Tires, the 705 Series are DOT approved Dual Sport tires designed for 75% street and 25% trail riding. A versatile tread pattern provides excellent wet and dry weather adhesion and the compound resists tearing while riding off-road. "R" in size denotes a radial tire.

Features:

• Aluminum air valve cap
• Comes in pairs
• Add some " bling " to your bike
• Helps Keep the air in your tire

We offer two different types of SuperMoto tubes. The first are Standard Tubes and are meant to be used with standard bias-ply type tires, but can be used with radial tires also.

But, if you are running radial tires, like SuperMoto, or have a retro bikes with spoked wheels and radial tires, you probably want to run the 'Radial Tubes'. Front tubes fits 120/70 and 120/60 tires. Rear tubes fits 150/60, 150/70 and 160/60 tires. These have a metal valve stem.

In order to be prepared for all possible mechanical mishaps along the trail or on any adventure, we are required to carry a certain selection of tools. The OBR ADV Gear Tool Roll will help keep those tools together and stored in an organized fashion easy to be found should one of those mechanical mishaps occur.

Features

• Heavy duty ballistic nylon construction
• Heavy duty #8 coil zipper
• Individual Tool Slots for Tire Irons, Wrenches, Screw Drivers … along with a zippered pouch providing secure storage for those smaller items
• Detachable 10”x10” slip pocket cover flap that also doubles as a hub pad keeping your hub out of the dirt when changing a flat
• Open dimensions 11” x 17”

This is a high-quality seat cover done by Moose for the TTR. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam. Strong marine-grade vinyl that's made to last. UV protected from sunlight for extended use and has double stitching for extra strength.

Our Adventure casual t-shirt, slightly redesigned from the original. Classic ProCycle Logo on the front left and a topo map of our favorite local riding spot in yellow on the back. High quality soft t-shirt perfect for everyday wear.

T-Shirt Specs:

• Retail fit
• Tear-away label
• Side seamed
• Shoulder taping
• Black Heather: 4.2-ounce, 90/10 Airlume combed and ring spun cotton/poly, 32 singles

This will give you a complete SET (Front and Rear) of brake pads.

• Sintered Pads are best for regular riding -long life, and good performance in all conditions.
• Sport Carbon pads are made for fast riding in dry conditions - not recommended for mud, water, or sand.
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered pads are high performance race pad with superb durability similar to that of the sintered pad. Higher friction level and fade resistance. Diamond ground surface finish to speed bed-in. Comes with new pad pins. Race Sintered are designed for racing use only; not for street use

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand

Kit includes front and rear brake pads.

EBC brake pad set.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads

• Aramid fibers have high strength-to-weight, thermal stability and abrasion resistance to provide advantages over cheaper steel fiber-based products
• Provide excellent stopping power without noise and rotor galling, even on polished rotors
• Fingertip control and strong, predictable brake response

DOUBLE-H SINTERED METAL PADS
Provide maximum brake effect and last twice as long as organic pads
Feature the HH friction rating – the highest in the industry

Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

Each kit includes all necessary rubber components and brake pins.

Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.

• manufactured from unique ebc low carbon hpsr steel
• laser & cnc punched for lightness
• hardened and ground for precision braking
• nickel coated to resist corrosion

This box moves up the rev limiter allowing higher revs. It also has a hotter advance curve from the OEM box. This allows for a bit crisper throttle response and easier starting. This is a "must have" for modified KLX110's.

• Raises rev-limiter 1200 rpm over the OEM ignition
• Hotter advance curve for better performance
• Direct replacement for the OEM CDI ignition box

Choose mechanical or hydraulic brake switches for your dual-sport conversion

Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.

The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!

• Accurately and quickly measures chain slack
• Two scales measure both chain slack and chain to swingarm clearance
• Setting chain slack properly dramatically improves chain life
• Lightweight compact design fits easily in your tool box or road kit
• Works on most street and dirt bike applications up to 75mm chain slack
• Made from engineered nylon with aluminum measuring scale
• Anodized laser-etched precision measuring scale
• Refer to your owner's manual for proper chain slack and procedure
• Patent pending

Cat Crap is the #1 voted anti-fog on the market. Lens cleaner and anti-fog in one. Works for all lenses, eyewear, goggles, helmet visors, etc.

Replace these any time you feel excessive play in the sprocket hub.

Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.

Sold as a full set.

Our Tool Tube mounts in place of the little stock tool carrier. The tube is made from 3 1/2" O.D. ABS pipe. It's held by 2 strong powdercoated steel straps. Both ends are sealed with waterproof expanding plugs. This is the ideal way to carry those items you always want to have with you on every ride. Tube is approx 13" long. Long enough to carry your Tire Iron Wrenches.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.