Universal fit. May require additional adjustment or modification.
Optimate Lithium 0.8A
At 0.8A, it’s a lower amp charger but still charges or maintains All 12V LiFePO4 batteries, protecting and keeping the battery at 100% charge. A great, cost-effective charger for your lithium battery maintenance.
A unique LiFePO4-specific program recharges and balances cells within the battery efficiently and safely. BMS re-activates battery from sleep or deep discharge protection mode. Protects LiFePO4 batteries in the most effective way. Protects a large investment and guarantees Lithium Iron Phosphate (LiFePO4 / LFP) batteries will perform as advertised for a very long time.
No risk of overcharging. Totally safe for vehicle electronics. Sparks suppressed. Safe for long-term battery maintenance. Automatic shut-down if short-circuited or battery disconnected.
A motorcycle rectifier-regulator is a crucial part of the charging system, acting as a charging control device to prevent damage to your battery and electrical system. These OEM-style units are direct replacements, providing the proper fit and the expected performance on your bike
Shorai batteries deliver more energy faster, with less weight and with less wear on the battery per start cycle than any other brand or technology available on the market today.
Up to 80 percent lighter than their lead acid equivalents
A Battery Management System that protects the battery from over-discharge.
Improved starting performance
Does not sulfate while sitting
Three year warranty
Weight (lbs): 2.45 lbs Weight (kg): 1.11 kg Cold Cranking Amps: 285 Polarity: [+ -] Dimensions: 5.8"x 3.4" x 3.5"
Self-adhesive foam shims are included and insure a great fit to the battery box, as well as extra vibrational an thermal insulation.
This box moves up the rev limiter allowing higher revs. It also has a hotter advance curve from the OEM box. This allows for a bit crisper throttle response and easier starting.
Raises rev-limiter 1200 rpm over the OEM ignition
Hotter advance curve for better performance
Direct replacement for the OEM CDI ignition box
These items are designed exclusively for closed course competition use ONLY. Use on public lands or highways in the state of California is illegal
Designed to enhance overall performance when installing a high-flow jet kit. This CDI box enhancements include:
Altered ignition advance curves
Wire lead for a tachometer
This unit may also be used to replace a defective CDI box on a stock machine.
Please note that the internal circuitry of Rick's CDI unit necessitates the engagement of the clutch or kickstand neutral safety switch for proper operation. Specifically, the clutch must be engaged (pulled in) when the kickstand is in the down position. This requirement may not be present in the original Yamaha OEM CDI unit.
This is an extended version of the stock DR650 clutch release arm that is manufactured by Suzuki.
Upgrading to a longer clutch release arm will lighten the pull of the clutch lever through means of increased leverage. This means less fatigue, quicker clutch engagement, easier clutch modulation and longer rides.
The extended clutch arm will not offer a drastic change in clutch pull. If you're looking for a major change in clutch pull at the lever, we recommend getting a Magura hydraulic clutch kit.
A direct replacement for the stock KLR hoses that tend to crack and leak after a few years.
These silicone hoses are custom made for us. Silicon hoses operate at much higher temperatures and pressures than other rubbers, they don't perish, and they look great!
The complete Thermo Control package - Our in-house designed Thermostat Bypass kit, a set of Custom Silicone Hoses and a Hi-Pressure Radiator Cap. All combined to help your KLR cooling system be at the top of its game. The Thermostat Bypass kit includes a thermostat with a higher temperature rating that will keep the motor more in its happy spot.
The Silicone hoses are stronger than the stock rubber units and will better resist cracking and leaking.
The Complete Doohickey Replacement Kit features the Doohickey supplied by Eagle Manufacturing, a torsion spring accompanied by a drill bit, a generator cover gasket, and an exterior cover gasket. Additionally, it includes all necessary components for rotor removal, along with a replacement bolt for reassembly.
Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
Stock and typical after market drain plugs can protrude past some skid plates. This steel low profile drain plug stays inside the skid plate so it can't be snagged by passing objects.
State-of-the-art replacement seats, Sargent seats are built on a percision-molded lightweight Polytec seat pan. Sargent's proprietary seat foam (Super Cell Atomic Foam) is their own unique blend of resilience, firmness, and vibration-absorption qualities, making it well suited for long distance comfort and support. Sargent seats are covered in a marine-grade, UV-stablized mildew resistant CarbonFX vinyl. Available in standard height and 1" lower than stock. These seats will fit bikes with the stock, IMS, or any other aftermarket fuel tank.
Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.
The correct spring rate for your weight will give a smoother more controlled ride. No more bottoming and better traction and confidence off-road. Kit includes required adapter collars
Stock Shock Spring 7.28 kg/mm
*Spring color may vary due to specification requirement and availability.
Lowers the rear suspension. Precision machined from billet aluminum and anodized.
*Important when lowering the rear suspension you want to raise the fork tubes in the clamps an equal amount of inches that the rear is being lowered. That way your bike will sit level when done.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Acerbis 3.9 gal tank adds function and great looks to your DRZ. This high capacity fuel tank incorporates modern lines and high quality construction that can't be beat. Includes gas cap, petcock and all mounting hardware.
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of the big Acerbis or Clarke tank? The 4.0 gallon tank from IMS might be just right. Includes cap, uses stock petcock.
This CNC cap will replace the stock gas cap on the stock tank. You do need some parts from the stock cap, so don't throw it away yet! It is not difficult and this kit includes the additional hardware required. Also included is a vent tube with a matching cap.
For use on STOCK TANK ONLY! This is NOT a locking cap.
Does not fit California model DR650
The Magura Hymec Hydraulic Clutch system. Simply remove the stock perch, lever and cable and bolt this in its place. This system replaces the stock cable with a small lightweight hydraulic system for improved clutch control, easier operating pressure, a constant pressure point and smoother actuation. Developed over many years and tested under the toughest conditions possible in the off-road motorcycle world.
You will have to bypass your clutch safety switch to use this unit.
Never hurts to have a bit of the Margura specific Blood Red hydraulic fluid as well.
The MAGURA HYMEC hydraulic clutch system gives you an ease and smoothness of pull that cannot be equaled by a cable unit. No need to lube the cable, no more broken cables. The HYMEC is simply a fantastic hydraulic retrofit clutch system. You will be able to get away with applying a lot less pressure than with a standard cable clutch. Depending on riding style, this can make for huge benefits in terms of riding comfort and control. The master cylinder control naturally has reach adjustment.
The advantages of the MAGURA hydraulic clutch are many:
Forged lever with improved lever ergonomics
Filled and delivered ready to install
Easy to install, detailed instructions included
Less energy required
Fine response
Finely tuned metering capability
No fluctuation in the pressure point
Maintenance free
First class workmanship-"Made in Germany"
MAGURA favors use of their 'MAGURA Blood' for its clutch systems. Mineral oil is non-toxic and not hygroscopic. Regular changes of the clutch fluid are not required.
We have worked closely with Magura to come up with a kit that fits properly.
Want an easier pull on your DR clutch? No cable to break? Then say hello to the Magura Hymec Hydraulic Clutch. Simply remove the stock perch, lever and cable in bolt this in its place. This system replaces the stock cable with a small lightweight hydraulic system for improved clutch control, easier operating pressure, a constant pressure point and smoother actuation.
Developed over many years and tested under the toughest conditions possible in the off-road motorcycle world. World champions to novices all agree on the benefits of the Hymec Hydraulic Clutch system. Due to demand, Magura is now making this available for many dual-sport motorcycles, and now the DR650!
Never hurts to have a bit of the Margura specific Blood Red hydraulic fluid sitting on your shop bench. 4 oz. bottle available as an option.
The MAGURA HYMEC hydraulic clutch system gives you an ease and smoothness of pull that cannot be equaled by a cable unit. No need to lube the cable, no more broken cables. The HYMEC is simply a fantastic hydraulic retrofit clutch system. You will be able to get away with applying a lot less pressure than with a standard cable clutch. Depending on riding style, this can make for huge benefits in terms of riding comfort and control. The master cylinder control naturally has reach adjustment.
The advantages of the MAGURA hydraulic clutch are many:
Forged lever with improved lever ergonomics
Filled and delivered ready to install
Easy to install, detailed instructions included
Less energy required
Fine response
Finely tuned metering capability
No fluctuation in the pressure point
Maintenance free
First class workmanship-"Made in Germany"
MAGURA favors use of their 'MAGURA Blood' for its clutch systems. Mineral oil is non-toxic and not hygroscopic. Regular changes of the clutch fluid are not required.
Universal fit. May require additional adjustment or modification.
The Apollo Heated Grips are designed with an integrated adjustable thumb switch, which allows them to easily fit on any kind of motorcycles on the market. The integrated thumb switch gives control to the rider to adjust the temperature level while keeping hands on the bar for a safer ride.
Its wide temperature setting range will keep the rider comfortable under the cold riding conditions.
The 5 color LED display will enhance the visual look of the heated grips and will allow the rider to quickly know at which heat level the grips are set.
This system will also detect if the battery voltage is too low and will automatically shut down the heated grips in order to make sure the rider have enough power to start the engine or use the motorcycle.
Specifications:
Integrated thumb switch designed for easy installation and control.
“Plug & Play” wiring connections to shorten the installation time.
Wide temperature settings for various weather conditions.
Low Battery Warning protection to ensure the motorcycle has enough power to start.
5 color LED Indicators for the rider to quickly know in which heat level the grips are set.
Universal fit. May require additional adjustment or modification.
Mika Metals Hybrid Series handlebars are truly a marvel of engineering. It is the first oversize handlebar in the world that fits on 7/8" clamps.
The patent pending design is the most unique idea to shake up the handlebar industry in quite some time. They retain all the flex properties of the pro series handlebars and allow you to run oversize bars without the oversize clamps.
Constructed from the highest quality aerospace 7075 aluminum for maximum strength. CR High Bend, includes injection molded bar pad.
Universal fit. May require additional adjustment or modification.
Sold individually.
The Adventure Kit is perfect for adventure and touring bikes where the mirrors are kept up most of the time. This mirror offers the widest field of view, and is ideal for riding paved and dirt roads. The 6 inch arm is a little longer than anything else on the market, for great visibility on loaded bikes.
Made from super tough glass reinforced zytel
Reflector Dimensions: 5.25" x 3.5" (135mm x 95mm)
Overall mirror length: 7" (175mm) (not including arm mount)
Convex lens meets SAE and CE specifications
Mirror mounts to any 10mm perch.
The new Doubletake ball is oversized, and high quality nitrile rubber surrounds an aluminum base that won't degrade under extended compression.
The Doubletake Base Kit includes bolts to thread into every application (even reverse thread Yamaha's), without adapters.
ADV 6" Arm Mirror
Kit Includes:
1 Adventure Mirror
1 6" arm
1 Ball Stud
3 Adapters (1Base Extension, 1 Reverse-Thread Adapter, 1 BMW Adapter)
The Nomadic Rack for the early generation KLR650. CNC laser cut from 3/16" 5052 aluminum with a large 12" x 18" mounting surface area. Sand blasted and then powder coated black to give it a shot peened look. This rack is an easy installation with no modifications required. There are multiple strap slots for securing gear bags and cargo. Rack is compatible with RotoPax mount. All hardware and instructions included.
Packages available include Rack with the RotoPax Mount or if you really want it all, you can order the Rack, Mount and a Fuel or Water Container.
PMR side utility racks are great for strapping down your soft luggage and keeping it off the rear plastics and exhaust pipe, while adding plenty of new tie down points for any luggage you have on your seat or tail section. They also add an enhanced level of security and strength to the rear end of your motorcycle in the event of a tip over or crash.
Sold as a pair. Easy to Install
Complete with all necessary mounting hardware
Fabricated with 1/2 inch steel tubing, MIG welded
Finished with a semi gloss black industrial grade powder coat
Comes with left and right side racks, each side weighs 2 lbs
Precision Motorcycle Racks strongly recommends these side racks be used with their Top Rack because the racks use each other to mount properly. They were never intended to be used by themselves without the rear rack. If you are going to mount these side racks without the use of their top rack please select the extra hardware kit option that includes 2 brackets, 2 steel spacers, and an extra hardware kit that is required for proper installation.
These side racks will not play nice with any other brand rear rack, and installation without their top rack will prove to be quite difficult.
The B&B Off Road Engineering rear carry rack is made from 4mm aluminum 5083 plate. This plate is chosen because of its extreme suitability for welding, abrasion and impact resistance, bearing in mind the full weight of the bike and rider. All Carry/Luggage Racks are supplied with the necessary stainless clamps and bolts where possible. Our carry racks are Tig welded with a polished finish and are sturdy enough to use as a grab handle.
DIMENSIONS
Width Flat Surface Approx 18cm
Length Approx 33cm – Total Length Approx 45cm
Please Note- To fit rack, two holes need to be drilled into the rear guard. The position of holes are already marked on genuine Yamaha guard so no template is required.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Significantly improves response and feel over factory rubber lines
Largest performance improvement for your money over any other braking upgrade
Stainless steel hose resists abrasion and puncture
Teflon core does not degrade over time like rubber lines
PTFE Dupont 64 Teflon® hose
Feature a heavy-duty stiffener sleeve and route just like the factory lines
Proprietary, premium fittings
Banjos utilizes a unique machined channel and sealing surface for leak-free installations
R&D and engineered in the USA
GBrakes USA controls the manufacturing process, ensuring the highest level of quality control
JT steel rear sprockets are manufactured using only the finest grade of C49 high carbon steel.
Two styles of rear sprocket were used on the DR350. The 90-95 'S' and 'SE' (street legal) models have a cush drive hub. The 96-99 'S' and 'SE' as well as all of the 'dirt only' models have a non-cush rear hub. Select your sprocket accordingly. If you are not sure, look at your bike. If the sprocket is bolted directly to the wheel hub you have a non-cush model. If your sprocket is bolted to a separate sprocket carrier you have a cush drive model.
The 50 tooth rear sprocket will give you much lower gearing for off-road use. You will need a longer chain for this rear sprocket, please order the 130 link chain to fit with this larger sprocket, it may need to be shortened to fit correctly.
Fully encloses the chain to guide it onto the rear sprocket. Stainless steel hardware, anodized aluminum plate, and plastic buffer for low friction and noise. Saves expensive engine cases.
Universal fit. May require additional adjustment or modification.
This Quiet Insert comes stock in all new FMF Q4 mufflers. If you lost yours, this is the replacement you need.
It will fit Q4, Q4 Hex, Powercore and Powercore Hex mufflers.
It will reduce the sound rating of the Power Core models, from about 99db down to about 96db.
Please choose the correct Insert for your muffler. If you are unsure of the year that your muffler was manufactured you can easily identify visually which insert you will need.
This gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
These gaskets seal the joint between the head pipe and muffler. They are easily damaged when removing the original muffler. Get a fresh pair now to ease installation of your new performance muffler. Sold as a set of 2.
This gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers do not require a joint gasket but the all other aftermarket mufflers as well as the stock muffler require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.
The RS-2 is a potent and versatile design that evolved from the original TRC, engineered to provide increased power and power delivery. With a different pyramidal shape that features increased volume, the RS-2 is a quieter system with a larger core - and it offers the added bonus of outstanding performance in a value-priced package.
Diamond-shaped Stainless steel sleeve for increased durability.
Large core and increased muffler packing volume means quieter operation
No repacking required! The Leo Vince X3 Enduro is made with TIG welded stainless steel internals and aluminum outer shell. It features a semi-direct chamber design that is maintenance free. It's quiet too! Our own in-house testing showed a 84dB sound level using the USFS J1287 testing procedure. 84dB is louder than stock but significantly quieter than any other aftermarket muffler. It includes a certified Spark-Arrestor.
Developed to increase the horsepower and torque throughout the entire power curve producing a noticeable power increase that is usable and compatible with every style of riding
Aluminum construction and stainless steel Hi-Flo end caps make for the perfect balance of performance and strength
Removable spark arrestor included
Backordered: Waiting for stock from suppliers to fulfill orders placed on or after April 2025
The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.
Uses long-life muffler packing for increased packing life
All of these options are for complete systems, including head pipe and muffler. The S option is for a Silencer only while the S/A is for a system with a Spark Arrestor.
The latest version of the Powercore 4 design incorporates a hi-flow core which mas more surface area to absorb more sound while flowing more exhaust. The silencer is constructed with an extruded aluminum canister is MIG/TIG welded and has space age internal packing. This system is lighter, stronger and provides more power than stock exhausts. The pipe is a stainless steel unit for strength and weight savings.
Powercore 4 S/A has a US Foresty approved, maintenance free, stainless steel spark arrestor screen to be sure you are safe and legal in the woods.
Repair leaking carburetor or worn out float needle assembly.
Kit contains all necessary gaskets, O-rings, float valve and jets
Supplied by the same supplier the OEMs use
Complete kit to rebuild OEM carburetor
The Phillips screws in Japanese motorcycles are not really Phillips screws. They are actually Japanese Industrial Standard (JIS) screws that are very easy to strip with Phillips head drivers.
Has your TM40 carburetor been sitting for too long and now needs to be rebuilt? Then what you need is this TM40 Rebuild Kit that contains Genuine Mikuni replacement parts.
All the advantages of a flatslide pumper carburetor at a much friendlier price than a Keihin FCR.
Our complete genuine Mikuni TM40 pumper carburetor kit comes with alloy adapter rings bonded to the carburetor body for a firm reliable fit in the stock air boots. We also include new 3" longer than stock throttle cables, a remote mounted choke knob, complete instructions along with a wide range of main jets and pilot jets for fine tuning or to accommodate bikes with extensive modifications.
Universal fit. May require additional adjustment or modification.
Attach this over your brake lever and hand grip, squeeze the brake lever, pull the locking bar in and lock the black portion down. This creates a locked front brake, making parking safe and secure with about 5 seconds of effort.
To unlock the BrakeFix, you just lift the back of the black hooking portion to release it. This takes about 2 seconds. Perfect for use with Snapjack type stands or just parking on an incline.
Universal fit. May require additional adjustment or modification.
These grips feature a thicker design that dampens vibration. The soft shoulder allows ease of movement. Three wire-tie grooves are molded into the grip to make securing them a breeze. We think they are great!
Do you have the SW Motech Centerstand and Skid Plate mounted to your Africa Twin? If so, it is a great idea to mount up the Skid Plate Extension. This plate adds protection to the undercarriage where the engine guard ends, giving you a more complete protection system. 3mm thick aluminum plate mounts to tabs that are built into the Centerstand. The Centerstand and the CS Extension function seamlessly together. These two pieces assure that you are completely protected down under. Kit includes Centerstand, hardware and detailed instructions.
Please Note that this Skid Plate Extension is only compatible with the SW Motech Skid Plate and the SW Motech Centerstand.
Clutch and Ignition covers made by B&B Eng. Formed from 2mm thick 5052 aluminum plate, selected because of its strength, corrosion resistance, excellent abrasion and impact protection. These will help protect your cases in the event of a bad fall.
These covers are attached to the engine cases with high quality heat resistance silicone adhesive
These covers will NOT fit early kick start only models that did not come standard with electric start. If you have added a kick starter to your bike that came with an electric start, covers will fit with no problem.
Warp 9's CNC shark fin rear rotor protector. To make installation super-easy this fin bolts to a brand new CNC machined caliper bracket. Just remove your existing caliper bracket and remove the pins, install them on this new one and then put the caliper and fin back on.
Universal fit. May require additional adjustment or modification.
For Straight 7/8" handlebar
Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.
Note: This kit includes the handguards only. Deflectors sold separate, can be added by selecting color from drop down menu.
For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.)
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
A premium billet sprocket carrier from Warp 9 Racing that houses 2 bearings to help protect against the sideways twisting load that is commonly known to prematurely wear out the bearing and cush rubbers. This wear can cause extreme failure possibly damaging the hub.
Offered in anodized Silver or Black, Includes spacers and hardware.
These are designed to work with Warp 9 and OEM hubs.
These top of the line Adventure pegs from Warp 9 are 5" long and 2.5" wide. They will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a singletrack trail.
Ceracote coated Chromoly steel pivot for the ultimate in strength
Replaceable 7075 T6 Aluminum Platform
Permanent Stainless Teeth provide the ultimate in non-slip traction
2 high-quality bushings per set. They recommend changing bushings every 40 hours or at least once a year to get the best performance out of a set. If you are on an Adventure Bike and are doing a lot of road miles they recommend swapping out bushings once a year to ensure that you get the most vibration dampening of the bushings.
Every new set of pegs comes with a 90A bushing installed. This is a medium flex rating. 80A is the softest and 95A lock-out is the stiffest and has the least amount of flex.
The bushings act like the suspension on your bike. With bushings, there are a couple of things to think about. The more firm the bushing the more durable and longer it will last. They use a durometer, a hardness scale 0 being the softest and 100 being the hardest. They don't go below a80 because they found that durability isn't great below this but have tested as low as a60 bushings. A bigger person that rides enduro-style terrain might want an a96 or a98 rated bushing. A lighter person might want the opposite but in the end, it comes down to personal preference.
The bushings are high quality yet inexpensive (they achieve this because they use skateboard bushings that are already developed and produced in massive quantities around the world) and a wear item designed to be replaced each season or depending on how hard or often someone rides.
The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail/stop light function. 3 white LED's are used for license plate illumination. Included is a set of turn signal brackets that bolt to the mount. These are designed for a small signal with a 8mm mounting stud.
This plug-n-play kit includes sealed LED headlight assembly and adjustable mounting brackets specifically designed for the 2008-2018 Yamaha XT250. The new design for the black headlight produces more light and has much more uniform beam pattern when compared to the previous version. New design currently only available in black, chrome may be available in the near future. No wiring, soldering, resistors, trimming, drilling, or fabrication required.
Universal fit. May require additional adjustment or modification.
A portable device that can jump-start your motorcycle or car. It can also charge your cell phone, GPS unit, laptop or other electronic devices via USB cable.
Universal fit. May require additional adjustment or modification.
Planning a motorcycle trip can be hard work. Butler G1 Maps highlight the best paved motorcycle rides in the country so you don’t have to guess which roads are good. Their dedicated team rides and rates every road you see on the water-proof maps, hundreds of thousands of miles so far. Their easy to read rating system clearly indicates the most dramatic and scenic stretches and are accompanied by detailed inset boxes, written descriptions, elevation profiles and whole bunch of useful information to help you plan your journey.
Universal fit. May require additional adjustment or modification.
If you already have a Quad Lock Case, you can Twist Lock and Go with any of these secure mounts.
Or Choose the Universal Adaptor to use your current phone case.
The Quad Lock® Handlebar Mount is the ultimate smartphone mount for motorcycles, compatible with all Quad Lock® Cases including the Quad Lock® Universal Adaptor for other Android phone devices.
The Quad Lock® Handlebar Mount gives you the flexibility to mount your phone in a convenient and visible location using a rotating head and includes an extension arm if extra clearance is required. With your phone securely mounted to your motorcycle, you can use navigation apps to guide you to your location with ease and always stay connected.
Standard:
Secure - Patented Dual Stage Locking Mount
Convenient - Use Navigation Apps on the go
Discrete - Small mount size
Multiple Mounting configurations (360 degree arm rotation)
Universal fit. May require additional adjustment or modification.
If you already have a Quad Lock Case, or Universal Adapter and Mount you can add these accessories to Twist Lock and Go on another level.
The level of vibration from some motorcycles can affect the image stabilisation on new smartphones. The Quad Lock Vibration Dampener ensures you can confidently mount your smartphone to any motorcycle.
FURTHER PROTECT YOUR SMARTPHONE
Compatible with all Quad Lock Motorcycle Mounts and Quad Lock Motorcycle Accessories, the Quad Lock Vibration Dampener reduces over 90% of high frequency vibrations produced by motorcycles.
PRECISION ENGINEERED
Featuring a dual chassis suspension system with precision engineered silicone grommets, the Vibration Dampener absorbs vibrations to protect your smartphone’s camera.
EASY TO INSTALL
The Quad Lock Vibration Dampener comes with everything you need to integrate with your existing Quad Lock Motorcycle Mount and can be installed in minutes.
For the frame drain on your XR650L ,extra protection for your motor! Strong magnet at the end of the plug picks up metallic flakes in your oil, protecting your engine!
Universal fit. May require additional adjustment or modification.
The Chilly Exhaust Heat Shield is the most effective heat shield on the market. The innovative three piece design consists of a top shield attached to 2 rails with rivets and spacers. This reduces the contact area and slows down heat transfer. They have incorporated a patented, insulated reflective blanket on the underside of the shield to reduce radiant heat transfer. The included stainless steel clamp makes it simple to install.
We highly recommend a heat shield if you run soft luggage without hard racks.
FEATURES:
Solid Top Shield- The logo is laser etched and there are no cutouts on the top shield. This prevents radiant heat from passing straight through to your luggage.
Side Rails- By isolating these with spacers the heat conductive surface area to the top shield is reduced and slows down heat transfer.
Radiant Heat Shielding- The reflective insulated blanket on the bottom of the shield is the real hero. This patented material won't be found anywhere else in the motorcycle industry.
Stainless Steel Clamp- Slots have been provided in the side rails to make installing as easy as it gets.
Brushed Aluminum- Lightweight and looks nice.
DIMENSIONS:
Length 7.5" (190mm) x Width 3.5" (76mm) x Height 1" (25mm)
