Search Products

Quality rebuild kit by Moose Racing. Comes with everything you need to get your stock carburetor back in shape!

Designed for use with stock engines using either stock or aftermarket exhaust and air filters.

• Provides a simple and affordable solution to carburetor tuning problems
• Allows you to tune your bike for increased power and smoothness while retaining fuel economy
• Includes a guide booklet on how to install and use your jet kit to it's full potential

• Increased air flow over the stock air filter.
• Designed to increase horsepower and throttle response.
• Easily fits inside the factory air box.
• Larger surface area over foam filters which offers longer service intervals in dusty conditions.
• Four layers of premium cotton gauze provides outstanding filtration.
• Washable & re-usable, never wears out.
• One filter will last the lifetime of your bike.

This seal helps keep debris and water out of your DR650 air box and it may become damaged or missing over the years. It is an important part of your DR650's intake system to maintain & prolong air filter life.

Simply, remove the air box door, then remove the old seal and clean out the track it sat in. Set the new seal in place and cut off any excess material remaining. Install the air box door and you are done.

• Dual-bonded foam design filters out even the smallest dirt particles, while allowing more airflow than two separate layer filters (flow bench proven)
• Twin Air filters are slightly smaller than stock to make them easier to change and to increase dead air space around the filter for better performance
• Flat foam sealing ring securely seats against the airbox, even in the worst riding conditions
• Complete kit that includes a new cage.  Replacement foam can be purchased separate for routine maintenance.

Dual stage foam: 2 different pore sizes create more trapping area for even the smallest dust particles. Flame laminated foam: Both "Stages" are not glued but heat sealed to provide maximum air flow. Light color foam makes it easier to see where the filter oil has covered and where it has not.

• Made of flame-laminated dual-layer foam, bonded with the highest quality glue to stand up to the roughest and toughest of any style of riding or terrain
• This filter, used with No Toil foam filter treatment, provides the best air filtration system in the world
• Fully open-cell structure for highest airflow and maximum protection
• Heavy-duty glue provides protection from all solvents
• Wide soft sealing ring for extra protection
• Flexible seams prevent cracking
• Original OEM size

All the advantages of a flatslide pumper carburetor at a much friendlier price than a Keihin FCR.

Our complete genuine Mikuni TM40 pumper carburetor kit comes with alloy adapter rings bonded to the carburetor body for a firm reliable fit in the stock air boots. We also include new 3" longer than stock throttle cables, a remote mounted choke knob, complete instructions along with a wide range of main jets and pilot jets for fine tuning or to accommodate bikes with extensive modifications.

This optically clear headlight guard is CNC cut for a perfect fit on your XT250. It is made of durable aircraft grade 3/16" thick cast acrylic which resists harsh rock impacts, trail scuffs, and incidental scratches. Velcro fasteners hold the guard firmly in place and allow for easy on & off should it need an occasional cleaning. Installation is a quick five minute job, positioning template included.

Double the size of your side stand footprint and half the chances of your KLR tipping over when parked on soft terrain. This laser cut, TIG welded 0.190" thick slice of aluminum bolts to your machine with just the addition of a hole in the stock side stand pad. Just takes minutes to mount.

Low peg mounts from JNS Engineering. Your choice of a straight 1.5" drop or get that drop and a 1" rearward offset. You can use your stock pegs or click on one of the optional pegs that are made to fit the stock DR650 mounts.

These heavy duty steel mounts are pressed, welded and then powdercoated black for protection. Includes mounting bolts.

Note: These mounts are compatible with the SW Motech Center Stand by adding a 1/8" spacer behind the mounts.

This is the ultimate adventure bike platform, it measures 2.25" wide, 4.75" long.

Patented adjustable collars make it easy to run them in the stock or lowered positions on most bikes.

Gain more room for bulky boots, or for longer legs. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long. Kamber bolts lets you adjust the 'tilt' of your pegs to increase comfort, or to give better squeeze on your bike.

Kit includes required fit kit.

Pegs that are designed for real adventure, providing a level of comfort not seen with other pegs. 2.25" by 3.5" makes for a platform that you can stand on for long periods with no worries. All necessary parts included for a direct bolt-on application.

Available in a beautiful anodized black or clear aluminum for durability and protection from the elements.

Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way. Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.

You can also order serrated or spiked cleats separately.

These AIR pegs are offered in several colors, but some colors may require extra time, call for availability.

The new Fastway Evolution AIR footpegs are now the ultimate pegs in the Universe.

Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way. Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.

You can also order serrated or spiked cleats separately. See images.

These AIR pegs are offered in several colors, but some colors may require extra time, call for availability.

Fastway offers a large ADV peg that is 4.75" long and 2.25" wide. With these pegs you can adjust the camber with their patented FKMS Kamber bolt. ´Tilt´ your pegs to increase comfort, or to give better squeeze on your bike. These pegs come with two sets of F3 cleats (one standard, one long). You can order serrated or spiked cleats separately.

These Adventure pegs are offered in several colors, but some colors may require extra time, call for availability.

This is the ultimate adventure bike platform, it measures 2.25" wide, 4.75" long.

Patented adjustable collars make it easy to run them in the 'standard' or 'low boy' positions on most bikes.

Gain more room for bulky boots, or for longer legs. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long. Kamber bolts lets you adjust the 'tilt' of your pegs to increase comfort, or to give better squeeze on your bike.

Finally, the ultimate Adventure peg, from the folks at Fastway - Pro Moto Billet. This peg is big enough to stand on all day with no fatigue, it measures 2.25" front to back and is 4.75" wide.

In addition to the big size, you can also adjust the camber with their patented FKMS Kamber bolt. ´Tilt´ your pegs to increase comfort, or to give better squeeze on your bike. You can further customize them with 3 styles of patented adjustable threaded cleats. Take your traction from comfortable to gnarly. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long. You can also order serrated (F5 - bottom left image) or spiked (F6 - bottom right image) cleats separately.

These Adventure pegs are offered in several colors, but some colors may require extra time, call for availability.

The new Fastway Evolution AIR foot pegs are now the ultimate pegs in the Universe.

Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way.

Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.

The ultimate Adventure peg, from the folks at Fastway - Pro Moto Billet. This peg is big enough to stand on all day with no fatigue, it measures 2.25" front to back and is 4.75" wide.

In addition to the big size, you can also adjust the camber with their patented FKMS Kamber bolt. ´Tilt´ your pegs to increase comfort, or to give better squeeze on your bike. You can further customize them with 3 styles of patented adjustable threaded cleats. Take your traction from comfortable to gnarly. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long.

These Adventure pegs are offered in several colors, but some colors may require extra time, call for availability.

Mounting these pegs to your KLR takes just a bit of work.

Please see link to the instructions below. These apply to the ADV and Evolution AIR Peg as well as the Evolution II pegs referred to in the instructions.

Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way. Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.

These AIR pegs are offered in several colors, but some colors may require extra time, call for availability.

Mounting these pegs to your KLR takes just a bit of work. Please see link to instructions below to see what you will need to do. These instructions apply to the ADV and Evolution AIR Peg as well as the Evolution II pegs listed on the instructions.

This is the ultimate adventure bike platform, it measures 2.25" wide, 4.75" long.

Patented adjustable collars make it easy to run them in the 'standard' or 'low boy' positions on most bikes.

Gain more room for bulky boots, or for longer legs. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long. Kamber bolts lets you adjust the 'tilt' of your pegs to increase comfort, or to give better squeeze on your bike.

The new Fastway Evolution AIR foot pegs are now the ultimate pegs in the Universe.

Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way.

Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.

These mounts provide a 1.0″ drop and 1.0″ shift to the rear which lowers your center of gravity and puts you in a better position of control especially when standing.

They are precision fabricated in Oregon. The icing on the cake, they are 0.5 pounds lighter than the factory peg mounts.

Upgrade your Honda XR650L with a Subframe Brace Kit, designed to enhance strength and rigidity for your bike. This complete kit connects the frame and subframe, reinforcing the structure to support increased load capacity—perfect for riders using side cases, top cases, and rear racks.

Key Features:

• High-Quality Materials: Attachment points are machined from 6061-T6 billet aluminum for superior strength and durability.. The 6.5mm thick support bars are laser-cut for a perfect fit.

• Easy Installation: No cutting, drilling, welding, or modifications required for installation. Easy 20 min installation.

• Enhanced Load Capacity: Provides added rigidity and support to the subframe, improving bike stability when carrying additional gear.

• Exhaust Compatibility: Compatible with both STOCK Exhaust and FMF Exhaust systems.

T-Rex stands are made from steel tubing finished in black powder for durability. Back by a 3-Year limited warranty for any material or manufacturing defects. Rest assured that you are getting best material commercially available.

Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools.

The indestructible, yet lightweight steel tube construction offers the best angle and ground clearance, makes it easy to jack up and provides stability - whether it's during maintenance or on the road. In most cases, you will no longer need to buy an additional swing arm stand. During long downtimes in the winter months, the centerstand helps take the load off your tires.

• Stands securely when traveling with lots of luggage and during maintenance
• Bike-specific design for easy mounting and high cornering clearance
• Easy to lift up the motorcycle
• Outrigger for optimal leverage
• Best corrosion resistance due to sand blasting and powder coating of the surface
• Made of robust steel
• Total Weight: appr. 1,6 kg / appr. 3.6 lb

New Hot Shot Suzuki Stator: aftermarket stator is made with heavy duty components and is a direct replacement for OE# 32101-32E01 or 32101-32E00. 

This stator will provide your bike with 20% more power (240W) to support your added gear. Whether you have heated grips or you're running multiple aux lights, this unit will give you the power that you're looking for.

Keep your smartphone, GPS and/or MP3 charged while enjoying your ride. Water- and weather-resistant, the Dual USB Port/Plug Charger offers you 5-Volt/2-Amp dual USB ports that have an inline fuse for protection. It comes with 38" of wire and 12" long battery quick connect rings. The mounting bracket that is included fits 7/8" and 1" bars.

• High sound level 105-118 db
• 80mm diameter and only 7.5 oz
• Wire extension included
• Universal for street and off road use

SuperBrace is the leading motorcycle fork stabilizer. This patented brace provides better stability, superior aerodynamics and a more streamlined look than other multi-piece braces on the market.

• Reduces low and high speed wobbles
• Improves stability in tight cornering
• Improves tire life and reduces cupping
• Decreases sensitivity to rough road surfaces and rain grooves
• Each SuperBrace is designed and manufactured for each specific motorcycle and made of 6061-T6 aircraft aluminum
• Ten minute easy installation

Limited to stock on hand

Quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

JT steel rear sprockets are manufactured using only the finest grade of C49 high carbon steel.

Two styles of rear sprocket were used on the DR350. The 90-95 'S' and 'SE' (street legal) models have a cush drive hub. The 96-99 'S' and 'SE' as well as all of the 'dirt only' models have a non-cush rear hub. Select your sprocket accordingly. If you are not sure, look at your bike. If the sprocket is bolted directly to the wheel hub you have a non-cush model. If your sprocket is bolted to a separate sprocket carrier you have a cush drive model.

These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

This kit will replace your stock sprocket bolts and nuts with new hardware.

Factory Honda replacements in a convenient kit.

Complete Gasket Set includes all the gaskets necessary to rebuild the entire engine and transmission, including valve seals.

Choose standard bore top end, big bore top end or a complete gasket set for the standard bore motor. These are high-quality gasket sets from Athena.

• The Complete Gasket set for the stock bore does NOT include Oil Seals. Must purchase those separately.
• The Top End Gasket set for the stock bore includes all the necessary gaskets, rubber parts and valve stem seals for a complete top end rebuild.
• The Big Bore Top End set includes a base and head gasket

GoldPlug is the gold standard in engine protection.

Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.

12mm Thread, 17mm Head.

GoldPlug is the gold standard in engine protection.

Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.

10MM Thread

Heavy duty springs help prevent clutch slip in high-performance motors.

• Custom wound from chrome-silicon wire
• Preset for long life
• Higher spring seat pressure to resist clutch slip

The PSR Oil Filler Caps are CNC machined from high quality aluminum and come with an E-clip that is already safety wired to a mounting tab. The wire is covered with silicone tubing that will not melt or discolor. Available in silver, black and gun metal.

The starter bushing in the DR650 leads a tough life. Exhaust heat and minimal lube from the factory take their toll. Warp 9 has a high quality solution - a billet starter cover with a sealed ball bearing.

• CNC machined starter endcap
• Black anodized for good looks
• High Speed Abec 3 double sealed roller bearing installed
• Reduced amperage needed to start bike
• Brushes will have extended life

New starters that are manufactured to meet or exceed OEM specifications. Pull out your old starter, put in this new one and go riding. These units are built to provide a longer life than the OEM unit with these features:

• The armature is insulated for rust and corrosion protection
• Rubber seals on the top and bottom of the unit ensure a dry operation
• 90/10 copper bushings
• Extended shaft replaces long or short shaft OEM starters

Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

Grab our 5-pack and save both time and money!

• Warp 9 Flex Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces
• Adjustable reach allows customization to the rider’s hand size
• Double hinge design allows lever to flex out of the way in most impact situations
• Pushrod or Bearing contact styles for smooth brake modulation
• Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal
• Will not fit with the stock OEM wind deflectors.

The Front Rack gives a lot of options for functionality.

CycleRacks are made out of Schedule 40 11/16 black steel pipe, bent in a press, and welded together in a jig.

All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.

Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.

The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary hardware is included. 10.5"Wx11.5"L

Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets.

Not only are Pro Moto Billet Cargo Racks brutishly strong and functional, but they look great too. Each cargo rack is methodically engineered, then CNC machined on-site from a 1/2 inch thick plate of USA made 6061 aluminum by master machinists.

The cargo racks are then hard clear anodized for durability. PMB uses only stainless steel fasteners for worry-free years of riding. Excellent instructions and all necessary hardware is included.

Need to mount your turn signals to your new Pro Moto Billet Rack? Just add a set of CNC machined aluminum Turn Signal Brackets.

Stamped from heavy gauge stainless steel, Giant Loop® Mounts bolt onto virtually any motorcycle, snowmobile, snow bike, ATV, UTV, SxS, 4×4—and even boats. These mounts help keep straps away from hot exhaust while shortening strap lengths for maximum stability and helps make installation of Giant Loop Saddlebags, Panniers, Dry Bags, and Tank Bags even easier. 

Sold as a set of two (2).

• DIMENSIONS: 2.5″ L x 1.75″ W (64 cm L x 44 cm W) Hole: 0.39” (10 mm)
• MATERIALS: Stamped heavy gauge stainless steel.

Keep essential items easily accessible with the OBR ADV Gear Sherpa Tail Bag. The OBR ADV Gear Sherpa Tail Bag attaches to your motorcycles rear rack via an optional strap free base panel or by a series of adjustable buckle straps. A padded spacious main compartment is perfect for carrying those items you wish to keep close such as tools, cameras, documentation, rain jacket, etc. A smaller mesh lid pocket sits above the main pocket for storage of smaller items.

Features

• High strength, abrasion and water resistant ballistic nylon construction 
• Heavy duty #10 coil zippers with storm flap
• Secure attachment to your bikes rear rack via an optional strap free plastic mounting plate or adjustable buckle straps
• Spacious and padded trapezoid 9x10x5 main compartment 
• Secondary lid mesh pocket adds even more storage
• Three sided reflective webbing with Molle loops
• 4 external D-rings on top lid with 3mm shock cord gives you a place to put those gloves during a ride break

• Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life
• Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material
• Triple-lip seal design
• Dyno-tested to last 3 to 4 times longer than OEM seals
• Directional ribs allow seal to be installed easily
• Kits include fork seals and dust wipers

Low friction 'triple lip' seal design. Oil seals last 3-4 times longer that OEM seals. Kit includes Fork Seals and dust wipers.

• Seal profile is engineered to create equal pressure in each seal lip; equalized seal pressure creates less drag and longer seal life
• Patented MAX-LIFE has a coefficient of friction up to 3 times less than the OEM seal material
• Triple-lip seal design
• Dyno-tested to last 3 to 4 times longer than OEM seals
• Directional ribs allow seal to be installed easily
• Kits include fork seals and dust wipers

The Moab shock from Cogent Dynamics will change how you feel about your KLR. You may like it now, maybe even like it a lot, but you will absolutely fall in love with it once you mount up a Moab shock.

Spring duties are handled by a custom spring available in either Standard or Heavy-Duty weights. The Standard spring will be fine if you are under 250 pounds and don't ride with luggage or passengers often. Ride heavily loaded or with a passenger regularly and you will probably want the Heavy-Duty spring.

For a true comfort and performance package, we highly recommend upgrading your front suspension at the same time.

Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.

A stiffer shock spring will help you get through the whoops or just help handle that extra baggage on the rear.

Stock spring rate is 10.5 KG/mm

*Spring color may vary due to specification requirement and availability.

Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.

Lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.

Stock spring rate 0.60 kg/mm

Race Tech Recommends 5w oil, 2 qts to reach 110 mm oil level.

A dual-rate fork spring for the early KLR650. These springs start with a .40 kg/mm winding and after approximately 20% of the stroke, stiffen up to .60 kg/mm for the remainder of the travel. A very nice improvement over the stock springs which are .40 kg/mm for the entire travel.

Cogent Drop-in Dynamic Cartridges will vastly improve both the compression and rebound damping of your stock forks. Designed by Rick at Cogent Dynamics on his high-tech suspension dyno, then tested and endorsed by KLR owners all over, these units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the units under the springs and hit the trails.

If you weigh up to 250 pounds, select the .64 spring kit. If you are over 250 or carry lots of luggage, please select the .70 spring kit. Please call if you have any further questions.

All of these kits include DDCs, springs, fork oil and preload spacers.

Precision tolerances – The tightest in the industry. Ultra-lightweight, for reduced unsprung mass. Straight rate springs will give better control.

Sold in pairs.

Aluminum alloy lowering link. Lowers the rear suspension approximately 1 inch.

Bearings included.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions 
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand 
• Race Sintered are designed for racing use only; not for street use

Includes front and rear pads

Rotors are laser-cut from high-carbon content 410 stainless steel then lap cross hatch ground and heat-treated. The finished rotors are mounted on a floating black steel carrier for durability and strength.

The oversize floating pins are CNC machined stainless steel rivets with stainless wave washers to ensure they will not crush as more traditional steel pressed rivets can. Finally, high-temp paint is applied to surfaces like cooling holes and edges to provide a clean, finished look.

Includes a fresh set of brake rotor bolts.

Did you snap a headpipe bolt on your XRL or are your headpipe bolts looking a bit dingy and rusty?

These replacement header exhaust stud bolts are made of super corrosion resistant 316 stainless steel.  They provide excellent resistance to chemicals and saltwater to give your exhaust system a hassle free service life.  

If you've got an older XR650L, you know the struggle of removing the O.E. nuts from the studs.  They either snap, remove the stud or come off as they should.  At some point you're likely to snap on or come across a seized nut to stud.  These bolts are a superior upgrade to the O.E. nut and stud.

Kit includes: 4 Stainless Steel bolts

• Developed to increase the horsepower and torque throughout the entire power curve producing a noticeable power increase that is usable and compatible with every style of riding
• Aluminum construction and stainless steel Hi-Flo end caps make for the perfect balance of performance and strength
• Removable spark arrestor included

The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.

• Uses long-life muffler packing for increased packing life
• Forest Service approved spark arrester

Set your bike apart with a custom exhaust look. Withstands direct heat up to 2000°F.

• 2 inches wide and 25 feet long
• Available in black or natural
• 4 stainless steel tie wraps

Clymer repair manuals provides step-by-step procedures based upon the complete disassembly of the motorcycle. This hands-on experience combined with extensive research results in a manual that is both user-friendly and detailed. Contains hundreds of original photos, exploded views, drawings, specifications and charts to illustrate each job. Also features shortcut repairs and high-performance modifications.

Whether you're interested in routine maintenance tasks, troubleshooting, or more extensive repairs, the in-depth coverage provides indispensable information about your KLR650.

All of these lines are stronger and more durable than vinyl fuel lines and are resistant to swelling, UV light, as well as hardening and cracking.

An OEM type replacement for the mighty XRL from the folks at Fuel Star. Single inlet that threads directly onto the stock fuel tank. Also works on the adapters that come on some aftermarket large capacity plastic tanks (like IMS).

Kit comes with a new Petcock, O-Ring, Fuel Line and Fuel Line Clamps! Everything you need for a complete fuel connection replacement.

3.5MM X 20FT

Made from Tough but lightweight 12 Strand SPECTRA / UHMWPE

2200LBS Break Strength

Double Looped Ends

Each Looped end is Covered in a Kevlar Sheath to protect the rope from abrasion

To be fitted to the top of the Barkbuster EGO handguard.

• Easy installation.
• Can be removed in minutes for a more compact feel.
• Deflectors provide maximum protection and coverage from the elements.
• Deflector Set available in black or white to suit your style.
• Includes two deflectors and mounting screws.

Fits Moose and other aluminum hand guards

• Aerodynamic and stylish design
• Protect hands from brush, water and cold wind
• Simple installation
• Sold in pairs

Construction of these handguards feature heavy duty aluminum guards with colored plastic deflector shields. They offer great protection from those trees that jump out at you on the trail and the cold wind and rain you encounter on the street. They feature a deep bend on the outer bar end for maximum freedom of hand placement and high quality bar mounts on the inside.

Select your desired color. 

Must add the corresponding size mounts to fit your handlebar.

For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.) 

Please Note: These handguards do not fit the Yamaha T7

For Tapered 1 1/8" handlebar.

Contoured alloy hand guards with inner mounts, allow space for the clutch cable and brake hose.

Note: This kit includes the aluminum handguards only. Plastic deflectors sold separate, can be added by selecting color from drop down menu.

For DR650 or other models with long levers add the optional universal fit Spacer Kit so you don't have to cut the balls off the end of your levers when installing these handguards. (May require additional adjustment or modification on some models.) 

Protect the underside of your TW!

• Made from 3/16' Aluminum.
• All Mounting Hardware Included

This rear master cylinder guard is fabricated from 2mm thick 5052 marine grade alloy, CNC machined from one piece for maximum strength and polished for great looks. Made to cover and protect the master cylinder from all kinds of situations, it is supplied with all necessary hardware.

• Protect your DR650 from overheating.
• Inline temp block kit works with Trail Tech computers Striker, Vapor, Voyager, Voyager Pro, and all TTO temp meters. 
• Installs between the oil cooler and top oil supply line, giving a cooled oil temp reading.
• Includes 3 new o-rings, and 2 longer bolts, as well as the Trail Tech m6x1.0 temp prob.

• Quickly dissolves dirt and grime without harming filter glues
• Simply spray on, hose off and re-oil filter
• Available in 15-ounce net wt. aerosol can

These Sequential Turn Signals are available in a 2 pack or 4 pack short stem with 7 LEDs.

Matte Black, plastic body with smoke lens and 8mm mount bolt.

Specifications

• E-marked.
• Short Stem: 75mm x 15mm

These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.

These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.

Replacement front fender by Maier that will fit great on your TW200.

• All Maier bodywork is made of tough, vacuum-formed high-gloss polypropylene
• Drilling is required
• Colors are OE color matched

Note: The proper way to install this front is to install the stock fender bracket to the under side of new Maier front fender using stock screws and nuts.

Protect your thumbs from blisters caused by riding on the inside of your grips.

Sold in Pairs.

• Combines wrench and bleeder valve into one convenient and compact tool
• Fits most 10 mm bleeder nipples
• Bleeds brake systems and hydraulic clutch systems
• Internal check valve for fast easy bleeding
• Anodized billet aluminum handle with chrome moly steel body
• Compact size for tight spaces
• High quality internal seal
• Multi position handle

Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers

• Knurled anodized aluminum locking ring
• Perfectly weighted to drive seals
• Carbon steel body halves

Use this installation tool from Cogent to be sure that your Cogent Drop-in Dynamic Cartridges are installed correctly. A strong magnet in the end holds the cartridge firmly while you lower it into your fork leg. Then slide the spring over the tool until it holds the DDC down, then gently remove the tool. That simple. Never again question if it is properly seated on the damper rod.

Works equally well for removal when you need to change your fork oil. Also works great with Race Tech Emulators.

ProCycle Dashboard designed to power multiple electronic devices. It can also be used for accessory lights, heated grips or gear, whatever you like. You can also use the two pre-drilled holes to attach a RAM mount and place your phone or GPS unit on that while charging.

The dash panel is manufactured from laser cut 5/64 mild steel and powder coated black. Also included are 2 weather resistant green LED rocker switches, and a voltmeter with two 4.2 amp weather resistant USB ports, a wiring harness with a built in 10 amp fuse/holder, and complete instructions. Everything you need to mount it and connect the outlets back to the battery.

An ADV tire designed in Australia for real off-road riding. Technically 25% stronger than many adventure tires with a tread deeper than most and a compound formulated to perform in a wide variety of conditions. The tread design on this tire is unique in that the blocks self-sharpen for better grip through the life of the tire.

If you want the best in traction, wear and dependability, try a set of Tractionator ADV Rear with Dual Venture Front. All sets now have Dual Venture Front with ADV Rear.

NOTE: All of the sizes listed are Tubeless Tires (unless otherwise noted) and can be used as such with tubeless certified wheels. Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.

• Long mileage, serious traction and smooth transition from pavement to gravel to dirt, the GPS does it all.
• Reversible rear to suit the rider’s needs – either 50/50 or Mostly Off-Road.
• In 50/50 direction the GPS is a well behaved street-able tire with smooth cornering transition from center to cranked all the way over.
• In Mostly Off-Road direction the aggressive straight line hook-up and cornering drive is engaged for better off-road traction.
• Stronger carcass construction than other 50/50 adventure tires provides world class performance with a high resistance to punctures
• Deeper tread than most adventure tires.
• Unique Hybrid compound with Silica for long mileage and optimum grip in mud and snow.

NOTE: Tubes can be run in Tubeless (TL) tires.

An Old School design that works great on today's Dual Sport bikes.

The rubber compound is engineered for high grip and long-lasting tread wear.

DOT approved, tube type, and might be the best value in a DOT knobbie.

Only available for: Samsung Galaxy S9

For use with Quad Lock® mounts and accessories sold separately. 

SECURE MOUNTING

Featuring a Patented Dual-Stage Lock that’s quick and easy to attach / detach, but secure enough to lift up to 80 kg / 176 lbs (yes, they've tested). It’s all in the technique, not in the force.

PROTECTIVE / IMPACT RESISTANT

We would never suggest throwing your device off a double story building, that’s just silly. But with a tough, polycarbonate core and impact absorbing TPU edge-to-edge outer shell, you can be confident that your device will be protected in your everyday activities.

SLEEK DESIGN

The slim profile and soft touch material make it perfect for everyday use. Simplicity is key in all of our design, no showboating here.

And yes, it’s compatible with wireless charging.

• Secure Quad Lock® interface
• Composite construction (TPU / PC)
• Microfibre lining
• Impact absorbing shell
• Compatible with wireless charging

This is a genuine Suzuki part. We recommend installing a countershaft seal retainer to prevent the countershaft seal from popping out while riding.

Order up your new levers here! If you keep breaking levers, you might want to think about a set of hand guards to protect them in case of a fall.

Warp 9 Flex Brake Levers are machined Billet, anodized and hinged brake levers with CNC machined master cylinder interfaces.

Adjustable reach allows customization to the rider’s hand size.

Double hinge design allows lever to flex out of the way in most impact situations.

Pushrod or Bearing contact styles for smooth brake modulation.

Titanium Pivot / Black levers with laser-etched Warp 9 logo CNC Billet Brake pedal.

Can break or rivet chains from #35 to #530 like a pro.

kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.

kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.

NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.

GET JumpStarter Mini, the second-generation, multifunctional jump starter. Now lighter and smaller, it's ready to help you restart any motorcycle or scooter when the battery is low. You can also use the powerful built-in LED flashlight or charge your use it as a power bank to charge your electronic devices. JumpStarter Mini comes together with a hard, water-resistant case perfect for carrying it anywhere and protecting it on your journeys.

• Light and compact multifunctional mini starter
• Allows restart of motorcycles and scooters when they are out of battery
• Can also be used as a Power Bank for electric devices thanks to the USB output port
• USB 5V2.4A output allows connection to tablets, smartphones, MP3 etc.
• Has built-in LED flashlight
• Easy to use; provides special protection against overvoltage and inversion of power supply polarity
• Start current: 200A, peak current: 400A, operating temperature range of -20°C to 60°C
• Includes JumpStarter, Smart Cable, 3-in1 USB cable and user instructions
• Measures 155 mm x 79 mm x 16 mm

This is the more economical alternative to eliminating the 990 Adventure airbox. Better breathing equals more power. The ITG filter kit makes air filter service a snap. It also simplifies other engine and intake maintenance chores. Our kit features a steel base plate which will not deform like plastic and does not conduct heat as much as aluminum. The white powder coating also helps reflect engine heat. To take advantage of the increased airflow, we recommend upgrading your fuel injection map with TuneEcu or a Power Commander.

• OPTION - Twin Air Breather Filter (replaces standard breather filter)

Don't get burned! Giant Loop's ingeniously simple and effective exhaust shield protects bags and bodywork from heat damage. The Hot Springs Heat Shield helps avoid the meltdown, preventing bags and side panels from touching your bike's exhaust. It's the lightweight, universal heat problem-solver for virtually any motorcycle exhaust system. Backed by a Limited Lifetime Warranty.