Genuine Keihin spring, washer, and oring for the fuel screw of FCR and FCR MX carbs.
Just the parts…
Fuel screw spring, washer, o-ring (fuel screw not included)
Each kit contains float bowl gasket (or o-ring), float valve assembly (or float needle) and o-rings to rebuild one OEM carburetor body.
Comes with everything you need to freshen up your carburetor.
Genuine Honda replacement air filter.
Dual stage foam: 2 different pore sizes create more trapping area for even the smallest dust particles. Flame laminated foam: Both "Stages" are not glued but heat sealed to provide maximum air flow. Light color foam makes it easier to see where the filter oil has covered and where it has not.
Hiflofiltro air filters are manufactured to fit the factory air box and are a direct replacement for original equipment filters.
Top quality powerflow filtering media, developed for modern high performance engines.
Twin Air's patented design, high quality materials and superior construction deliver unbeatable performance and protection - and make Twin Air Filters the hands-down choice of more World and National Champions than all other filters combined.
An air filter is your engine's only protection against the elements, and your stock filter isn't up to the task. Replace it with a Twin Air - the #1 filter system proven on motocross tracks around the world.
Twin Air's fused layers of open-pore foam and fine inner foam trap even the smallest particles-without restricting airflow.
Replacement rubber boot for choke knob assembly.
Providing unbeatable performance and exceptional value, Hi-Flo Filter is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
Grab our 5-pack and save both time and money!
Superior Filtration:
Honda recommends replacing this oil filter screen every 7500 miles.
The Complete Doohickey Replacement Kit features the Doohickey supplied by Eagle Manufacturing, a torsion spring accompanied by a drill bit, a generator cover gasket, and an exterior cover gasket. Additionally, it includes all necessary components for rotor removal, along with a replacement bolt for reassembly.
Includes forged JE 89mm piston 10.5:1 piston, Rings, Clips, Pin, big bore sleeve and top end gasket set. You will have to have the big bore sleeve installed in your cylinder and bored to fit the larger piston.
Replacement friction plates and drive plates.
Gasket for the engine case cover over the clutch. Doing any clutch work, you probably want to replace this gasket so you don't have any leaks when you are all done with the project.
A high quality top end gasket set for the XR650L
Clymer manuals are the most user-friendly repair manuals. They are written for the do-it-yourself-er as well as the experienced mechanic by industry experts. Step-by-step instructions based on the complete disassembly of the machine. This manual in written to cover 90-94 models but nearly all of the information will apply to newer models also.
Genuine Honda Factory Service Manual specifically for your CRF250L
Honda XR650L rear shock upgrade. The experts at Cogent Dynamics know suspension! A proven performance rear shock for your XR650L for use under the most demanding conditions and on the roughest terrain worldwide.
Damping rates optimized to your specific needs, giving you the best ride comfort, traction and control. Frequency and velocity sensing valving works great over wide ranging conditions. Low internal friction. All CNC machined components for top quality and performance. Compact and rigid design with internal separator piston. Adjustable for spring preload and rebound damping. Fully serviceable shock is designed for the long haul.
*Spring color may vary due to specification requirement and availability.
| Standard Spring | 10.71 kg/mm |
| Heavy Duty Spring | 12.50 kg/mm |
| Low Shock | 1.5 inches lower |
Good News: There’s finally a plug & play LED headlight conversion kit for your 2008-2020 WR250R and WR250X!
This kit includes a sealed LED headlight assembly with plug & play electrical connection, adjustable powder coated steel mounting bracket set, and mounting hardware.
Installation is a five minute, one beer exercise. If you can change a residential light bulb you will have no problem installing this conversion kit. We promise.
Please note that you will need to reuse your OEM upper headlight mounting grommet and two aim adjustment springs. Or add new ones to freshen up your whole headlight unit.
Low Beam: 2,100 Lumens, 20 Watts
High Beam: 2,800 Lumens, 30 Watts
Operating Voltage: 10V-30V DC
Color Temp: 6,000K
Lifespan: >50,000 hours
Acerbis 5.3 gal tank adds function and great looks to your DR650. This high capacity fuel tank incorporates modern lines and high quality construction that can't be beat. Includes gas cap, petcock and all mounting hardware.
Installation of the Acerbis tank requires relocation of the front turn signals. Otherwise the stock signals will contact the tank at full lock. Our Turn Signal Relocation Brackets Move the front turn signals up and forward to clear the bigger tank.
Limited Time SALE Blue Only
The new 4.1 gallon fuel tank from Clarke. Carries almost 2 more gallons than the stock tank. Available in Blue, Black, Silver, White or Natural
More range at a great price. Choose the 2.6 gallon tank for the newer KLX250S in Black, Green, Natural or White.
This tank will NOT fit the 2006-2008 models.
Get better range from your early KLR650 by adding an IMS 6.6 gallon fuel tank. The big tank also provides radiator protection.
Designed to enhance the appearance of your motorcycle, yet provide greater riding distance per tankful. Larger capacity than stock, yet very slim and sleek. Perfect for the dunes or the race track! These tanks are made with POLYETHYLENE CROSSLINK for extra strength and durability.
Natural color is recommended if you wish to easily see the fuel level in the tank.
This tank requires you to re-use your stock petcock valve. Does Not Use OEM/Stock Shrouds
Available for stock gearing, 49 tooth rear sprocket
OEM Honda rear sprocket for the XR150L
Reduce the friction dragging down your drivetrain. This chain roller is made from Delrin®, it's self-lubricating and a significant improvement over stock.
Does not use a bearing but rides directly on the frame boss. There is no mounting hardware included.
A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.
Fits 520, 525, and 530 pitch chain.
A fresh set of brake rotor bolts. These bolts already have thread lock compound applied to the threads.
Stock OEM works with factory rotors, comes in a pack of 6.
For aftermarket rotors like Warp 9 or EBC front and rear sets are available.
Front comes in pack of 6
Rear comes in pack of 4.
A kit consisting of 15 (9 front - 6 rear) KLR650 rotor bolts, enough to do the front and rear.
Class 10.9 steel rotor bolts provide excellent sheer strength and include medium-strength threadlock patches to securely fasten your rotor
Special tool to remove the flywheel/rotor from the end of the crankshaft. You have to remove the flywheel/rotor to upgrade the doohickey.
Secure storage of a spare tube, tire irons, or random miscellaneous items is a must for any trail ride or adventure. The OBR ADV Gear Fender Bag is constructed from a heavy duty industrial grade ballistic fabric that secures tightly to any fender via oversized heavy duty gutter hooks. The OBR ADV Gear Fender Bag also utilizes an optional double button snap system that when used eliminates any potential for shifting of the fender bag when riding off road or over rough terrain.
Features
THE LUGGAGE RIGGING POSSIBILITIES ARE ENDLESS!
This kit will set you up with the full Green Chile Adventure Gear treatment. You will be able to haul up to four bags of your choice. One system that can be rigged for day trips and easily scaled up for an expedition or extended trip.
No expensive bags required. Any bag becomes motorcycle luggage.
Don't have a rack on your bike? No problem! The flexible soft rack system attaches easily to fenders, footpegs, sissy bars, or your existing rack. Just tighten up the sturdy cam buckles and you're ready to get rigging! Use the versatile combination of runner loops, tensioner straps, and velcro loops to affix any bag you please to any one of over 60 daisy-chain style contact points.
Contruction Features:
This Kit Includes:
Nomadic Rack for the TW200. CNC laser cut from 3/16" 5052 aluminum with a large 12 x 10-7/8 mounting surface area. Sand blasted and then powder coated black to give it a shot peened look. This rack is an easy installation with a 4 point mounting system with no modifications required. There are multiple strap slots for securing gear bags and cargo. Doubles as a grab handle or tow bar. Is compatible with RotoPax mount. All hardware and instructions included.
You may purchase just the rack or you can order the Rack with the RotoPax Mount. If you really want it all, you can order the Rack, Mount and a Fuel or Water Container.
Simple, lightweight rack made from rugged 1/8" 5052 Aluminum, with a rigid 5-point mounting system.
Low profile allows for easy seat removal.
Features:
Note: Placement of this top rack does require removal of the stock tool bag.
Cycle Racks Bag Supports can used for many different Cycle Racks and can be used on either the front or rear rack.
When they developed these, they wanted a functional, yet "Easy On- Easy Off application. The pig tail hook goes up, over and underneath the bar of the rack, they can also be used upside down on the rear rack as side boards. To install them, wing them out, slide them in place and then wing them back down. Simply reverse the process to remove them.
Rok-Straps are supplied to secure them in place. They are pre-drilled to accept the pattern of the Roto-Pax Pack Mount (sold separately) so you can carry fuel or attach them to your own bags.
They are sold together in a set of one right support and one left support.
COLOR: Black
Pair of medium sized expandable saddle bags that can either be side or top loaded. Semi-rigid construction made of thermoformed EVA. These saddlebags are expandable up to 30 liters. Hexagonal design matches the angular styling of modern sport, sport touring, and adventure bikes.
Features:
Constructed from heavy-duty waterproof tarpaulin with durable heat welded seams. This coated material makes clean-ups a breeze. Roll-down tops create a waterproof seal and are held in place with heavy-duty ITW quick release buckles. Wide support straps are adjustable via hook and loop material to fit almost any width seat.
Replacement Cleats for use with Fastway Pegs.
Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. These pegs are 50mm x 75mm.
Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools. Tough black powder coated finish.
For riders who wish to run the centerstand and the lowered footpegs we recommend installing a Warp 9 brake pedal. The Warp 9 pedal is arched to give the necessary clearance under the pedal.
This adapter set is required to fit an aftermarket spring to the Vstrom shock
Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.
Adapters are required for this spring
Both kits include all bushings, snap rings, and washers.
Gen 2 kit also includes the necessary O-rings.
Gen 1 kits are OEM bushings, snap rings and washers.
Billet aluminum lowering links. Lowers the rear suspension approximately 1 to 2 inches depending on application.
*Important when lowering the rear suspension you want to raise the fork tubes in the clamps an equal amount of inches that the rear is being lowered. That way your bike will sit level when done.
Note: We only recommend the 2" lowering links for lighter non-aggressive riders as they allow the tire to rub when near bottoming.
Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.
Some KLR models from 2004 - 2007 may have a longer shank that do not allow the bolts to tighten to the bearing. If that is the case, we recommend the addition of either a 14 mm split type lock washer or a 15 mm flat washer under the nut of both link mounting bolts.
Reproductions of the original DR650 factory turn signals. Save a bundle compared to the $70+ each cost of the OEM signals. The wire pigtails plug directly into the factory harness. No cutting or splicing necessary. Choose original style amber lens or clear lens with amber bulb.
Bike-specific light mounts made of powder coated steel allow easy installation and maximum stability, even off-road. Includes mounting material and instructions.
This listing is for the mount only, no lights included.
This kit is not just a bulb, but an entirely new LED specific headlight! A specially designed adjustable steel mounting bracket replaces the stock unit. Included is a wiring harness and all the required hardware to make this installation quick and easy and entirely plug and play. No cutting, drilling, or wiring modifications are necessary. The headlight features separate low and high beam projectors in a custom headlight shell designed specifically for this LED bulb.
This kit is available with either a chrome or black chrome reflector in the headlight.
Check out the images for stock vs. LED patterns and brightness. (Images are of a DR/DRZ unit, but the light unit is the same as that on the XRL.)
Replacement folding shift lever, stock length made by IMS.
A stock replacement brake pedal for the DR650. Nothing fancy but sure gets the job done. Just order it up and get back on the trail. See our Brake Pedal Adjuster Bracket that allows you to adjust the position of your brake pedal to perfection.
Sold individually.
Enduro Mirror 4"
The Enduro Kit is a great option for your street legal dirtbike if you fold away your mirrors often. The longer stem helps the reflector fold behind the headlight and gives good visibility when extended.
Their Doubletake Arm 3.5" is perfect for aggressive riders- long enough to see, but small enough to tuck away.
The new Doubletake ball is oversized, and high quality nitrile rubber surrounds an aluminum base that won't degrade under extended compression.
The Doubletake Base Kit includes bolts to thread into every application (even reverse thread Yamaha's), without adapters.
Mika Metals Hybrid Series handlebars are truly a marvel of engineering. It is the first oversize handlebar in the world that fits on 7/8" clamps.
The patent pending design is the most unique idea to shake up the handlebar industry in quite some time. They retain all the flex properties of the pro series handlebars and allow you to run oversize bars without the oversize clamps.
Constructed from the highest quality aerospace 7075 aluminum for maximum strength. CR High Bend, includes injection molded bar pad.
Bars only fit 7/8" clamps
Keep track of your keys easier with our embroidered patch on a keychain.
Finished with metal ring with eyelet and merrowed border.
Patch measures 1.5" x 5"
As pictured; includes:
| 2 | Classic Swingarm Stickers (1% power gain) |
| 1 | Sheet of 3 small "black" stickers |
| 1 | Sheet of 3 small "yellow" stickers |
| 2 | "Adventure Begins Here" stickers |
The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.
Delayed stock from manufacturer, please ask for availability.
The RS-2 removes 2 pounds from the stock unit and it also provided the XR an increase of +5% max HP and 1.7% max torque. Now the XR has gains across the entire power spectrum and is ready to tackle trails and highways alike.
This RS-2 Enduro Series Slip-on includes an installed USFS spark arrestor SA-02-K.
Yoshimura's RS-2 is proudly designed, developed and manufactured in Chino, California.
This gasket seals the joint between the head pipe and muffler. These gaskets are easily damaged when removing the original muffler. FMF mufflers do not require a joint gasket but all other aftermarket mufflers as well as the stock muffler require a joint gasket. Get a fresh one now to ease installation of your new performance muffler.
This gasket seals the joint between the head pipe and Exhaust port. These gaskets are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now avoid having an exhaust leak when you install your new exhaust.
Reusable billet aluminum muffler joint gasket. Factory joint gaskets usually cannot be removed from the pipe without damage. This one can be used over and over again. Pays for itself the first time you need to remove you muffler during service or repairs.
Additional protection against rocks and contact with the ground for the engine: the high-quality, aluminium alloy engine guard shows what it's capable of off the street, but provides extra safety and an individualized look on the streets, too. State-of-the-art production gives these bike-specific protectors a secure fit. The installation on frame mounting points lends additional stability and allows for easy installation.
Made from strong and lightweight 4mm thick aircraft aluminum.
Protects vital engine parts from rocks and debris.
Custom fit to your specific bike model.
Oil drain hole for easy access.
All mounting hardware included.
Constructed of 3mm-thick (1/8"-thick) aluminum for heavy-duty, light-weight protection. Baseplate includes side protectors that wrap around the engine case to provide both bottom and side protection.
This is one of the gnarliest skid plate made for the KLR. Made from 3/16" aluminum, it is laser cut and CNC formed. All seams are welded on both sides and the entire plate is black texture powder coated. Includes all the mounting hardware.
This is one of the gnarliest skid plate made for the KLR. Made from 3/16" aluminum, it is laser cut and CNC formed. All seams are welded on both sides and the entire plate is black texture powder coated. The plate mounts in minutes using stainless steel hardware.
IMPORTANT NOTE: The standard kit will work with all crash bars except for Givi and Happy Trails. Select the Givi option for that brand. This plate will not work with the Happy Trails crash bars.
Select the optional heavy duty mounting brackets if you want to replace the wimpy stock mounts with steel brackets.
Moose Racing's Heavy-Duty, 4mm thick 5052 aluminum, to protect expensive and fragile radiators from side impacts and twisting.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 3 |
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 2 |
All the parts you need to freshen up your front brake caliper. New piston seals, slide pin and boots. Fix that sticky or limp front brake.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.
Made by Nissin, an OEM supplier in Japan
EBC Double H Sintered pads feature the HH friction rating - the highest in the industry.
Provides maximum brake effect and lasts twice as long as organic pads.
Motocross brake rotor featuring ultra lightweight radically profiled contours for great looks, great self cleaning and brake performance. Made with tough and durable heat treated stainless steel. Heat treated to perfection and then diamond ground to micron accurate surface finish and parallelism and will deliver great brakes that perform well and last.
Stock size rear brake rotor laser-cut from high-carbon content 410 stainless steel, then lap cross hatched and heat-treated. Each one then has a high-temp paint applied to surfaces like cooling holes and edges for a clean finished look.
Includes a fresh set of brake rotor bolts.
Dual Sport tube-type tires for the TW200 or the VanVan.
With its versatile tread pattern, the E200 makes an ideal OEM replacement.
Dual Sport tube-type tires for the TW200 or the VanVan.
With its versatile tread pattern, the 428 makes an ideal OEM replacement.
Front tire is a 130/80-18 (66P load / speed rating) while the rear is a 180/80-14 (78P load / speed rating).
From Michelin. An innovative tread pattern with blocks and curved grooves, based on the Dakar-winning Desert Race tire, provides real off-road performance especially in soft terrain and challenging conditions. Specially designed compound gives a long tread life for extended adventure rides. Front and rear tire casing design ensures excellent on-road stability.
An -R after the size indicates that these are Radial tires.
These tires are R-rated (max speed of 106 mph)
Heidenau tires are made in Germany and they are high quality motorcycle tires for street, off road and adventure riding.
Durability, It’s about the Rubber
Heidenau’s compound uses a high natural rubber content, and there’s a lot on there. This naturally resilient compound, combined with sturdy Belted construction, makes for one of the most trusted, longest lasting tires available to long distance travelers.
K60 Tread design:
The K60’s interrupted block chevron pattern makes for a respectable off road tire that’s smooth on the street.
Heidenau tires are made in Germany and they are high quality motorcycle tires for street, off road and adventure riding.
A tire worthy of standing side by side with the legendary K60 Scout. The K60 Ranger is designed and developed to be the off-road cousin in the K60 family. This is not a Scout with different tread. Heidenau started from scratch with entirely new carcass and compound to maximize off-road performance and reliability.
“Rated by Heidenau as a 30% street / 70% off-road tire, the new K60 Ranger sits next to the K60 Scout in Heidenau’s lineup, offering a more off-road biased design to help adventure riders explore further into the backwoods with more confidence to tackle difficult terrain. Like the Scout, the K60 Ranger also gets a reinforced carcass with high puncture resistance. Where it differs is a more-open, knobby tread pattern that utilizes large gaps between center blocks, instead of a continuous center strip, giving it the ability to dig into loose terrain more effectively. What’s more, the Ranger utilizes a softer rubber compound that helps increase grip both off-road and on the street. Plus alternating side lugs, tied together with crossbars, enhance the tires ability to climb out of ruts and improve cornering stability.” – Rob Dabney - ADV Pulse
Tread design:
The K60 Ranger’s new tread design has dirt and big bikes in mind. While the open block design should keep the tread from loading-up in muddy conditions, the compound and carcass should keep the ride stable when you’re back on the street. With features intended to give integrity to the side blocks, the K60 Ranger should be at home on single track or cruising down the highway.
Tubeless tires (TL) can be used with spoke wheels, but Tube Type (TT) tires cannot be used with TL wheels.
New tires and tubes deserve new rim strips! Choose the correct size for your wheels and toss-out those old cracked and broken ones.
For 19" rims, please order the 18" rim strip. These fit just fine!
Be sure to order the 2.25" wide strip ONLY if you have SuperMoto rear rim. This is a 16" strip that will fit your 17" SM rim perfectly!
You can purchase single strips or sets for your wheel sizes.
Optimate 1 Global Charger-Maintainer
This charger is perfect for 24 hour, 7 days a week, 365 days a year smart battery maintenance. It delivers precise microprocessor controlled charging and long term maintenance.
Maintain any type of 12 volt lead-acid (STD, AGM, GEL) and 12.8V/13.2V Lithium (LFP) Non-RS/Non-BMS batteries without overcharging. Ideal for vehicles that are seldom or seasonally used, or kept in storage.
Global Three-step charging program ensures effective charging of the battery and is safe for prolonged connection to the battery, without risk of overcharging. Automatic shut-down if short-circuited or if battery is disconnected.
Dust proof case with wall mounts and 6ft AC supply lead and 6 ft charge lead ending in SAE connector. Weatherproof battery lead & OptiMate battery clip set included.
Charges and maintains all 12 volt lead acid, gel and lithium iron phosphate (LiFePO4)/lithium ion polymer Non-RS/Non-BMS powersport batteries
Features:
The Shorai LFM Duration Recommendation is the best overall pick for most applications, and has been selected to give strong cranking performance and long lifespan.
Measures 4.45" x 3.5" x 2.28"
Weight (lbs): 1.52 lbs
Weight (kg): 0.69 kg
Cold Cranking Amps: 210
Polarity: [- +]
Each Shorai battery includes self-adhesive foam panels to achieve a snug fit in your battery box.
The set includes a 27mm for the rear and a 22mm for the front. Each 10 inch forged steel tire iron has a hex wrench on one end. The rounded spoon end minimizes pinched tubes and scarred rims.
This is a DRC wrench for your axle nut on one side, and a great tire spoon on the other.The long handle makes it easy to undo tight axle nuts and give you a bunch of leverage for changing tires. These are heat treated steel and range from 10 to 10.6 inches long.
The Moose Tire Bead Tool holds your tire in place as you work you way around the tire
Made of aluminum with a nylon screw so it will not scratch the rim
Sold in pairs
Don't hit the trails without these tire irons. Each 10 inch forged steel tire iron has a hex wrench on one end. A 22mm for the front and a 24mm for the rear for older generation KLRs ('87 - '07) or a 19mm for the front and a 27mm for the rear for the new generation machines ('08 and newer). Rounded spoon end minimizes pinched tubes and scarred rims.
Ever had to turn back on the trail because of downed limbs? Or have you ever been moto camping and needed some wood for a fire?
This is the tool for you then! We have tried this manual chainsaw and it makes quick work of hard woods like Oak.
The chain itself is 25 inches long with 8 inch nylon straps at each end. All together this saw weighs 1/4 of a pound. This will tuck away nicely into any tool pouch or saddle bag as it roll up into a tight round.
Replace these any time you feel excessive play in the sprocket hub.
Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier.
Sold as a full set.
Here is the little switch that mounts inside your brake or clutch lever perch and controls the brake light or clutch safety circuit. This switch often gets damaged in an unplanned dismount (aka: crash) or the plastic simply cracks from age. When this happens, you can find yourself chasing a short circuit that keeps blowing your fuse every time the brakes are applied. If this has happened to your TW, here's the fix!
Ride in warm temperatures a lot? Worried about your motor oil just getting too hot? The Trail Tech Universal Fan Kit mounts up to the backside of the DR's oil cooler to draw cool air across it and keep those oil temps down. An electronic temperature sensor mounts to the fan, no need to cut any fluid lines, and automatically turns the fan on when needed to keep the temperature in the optimum range.
The activation sensor can be set wherever you like to keep the temperature right where you want it. Backlit for easy viewing anytime it also includes a volt meter.
Kit Contents
This is the secret for being able to put in those 500 mile days. Even a good touring seat can feel a bit harsh after a couple hundred miles. These very comfortable sheepskin seat covers give you that extra bit of 'cush' and provides superior air circulation. Velcro straps allow easy install and removal when you don't need it. Measures 14" wide by 19" long, the perfect size for Dual-Sport seats.
This is the brace needed to stabilize the wing like structure they call a front fender on the KLR – both generations. This simple bolt-on reduces wind buffeting and increases steering stability at highway speeds. It also helps carry the weight of a fender mounted tool bag.
Made from laser cut 5052 aluminum, then CNC formed and beautified with a shiny black powder coat. Easily mounts in a few minutes using the included stainless steel hardware.
