Search Products

Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Head and mid-pipe are constructed from 304 stainless steel. Entire unit is pounds lighter than stock and gives great horsepower and torque gains throughout the RPM range.

All handmade in the USA with a 1 Year Limited Manufacturers Warranty.

These gaskets seal the joint between the head pipe and Exhaust port. They are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now avoid having an exhaust leak when you install your new exhaust. Sold as a set of 2.

Ultra-Light, Race Inspired Titanium Muffler

Available in slip-on/bolt-on and full system configurations depending on the application

• Titanium body
• Spring retained inlet
• 2.25" Spiral perforated core
• Billet CNC machined aluminum outlet
• Carbon fiber end cap
• Tunable for tone with P1 and P1-X insert options
• Stainless steel headers/mid-pipes where applicable
• Made in the USA

Replacement Exhaust Pipe Retention Spring

• This swivel spring replacement will work on nearly any exhaust system with a similar spring.
• Made from stainless steel, and has a high temp silicon sleeve to protect exhaust component finish.
• Made by Akrapovic, 60mm size, SOLD EACH

Quality air cutoff valve replacement kit contains parts necessary for a complete rebuild.

• Direct OEM-style replacement carburetor air cut-off valve set
• Includes diaphragm, spring and O-ring
• Located on the side of the carburetor, the air cut-off valve prevents lean fuel mixture (backfire) when decelerating
• Temporarily closes the pilot jet airway to provide a richer mix as the throttle closes

Repair kit comes with everything you need to get your carb back in shape.

Genuine KTM replacement air filter. Replace your air filter at recommended service intervals.

The map selection switch allows the rider to switch between two different maps "on the fly" within the Power Commander V.

Don't have a dyno tuning center nearby? Are you more of a do it yourself type? Are you constantly changing parts on your bike?

If you answer "yes" to any or all of the questions above, then our Auto Tune kit is for you. The Dynojet Auto Tune kit is an "add on" accessory that can be used with any of the Power Commander Vs

It connects to the PCV with a single cable and requires only a ground and +12 volt connection to be made to install. If your exhaust does not already have one, a "weld in" O2 sensor bung is included

Once installed, the Auto Tune kit monitors the fuel mixture (by installing the included Wide Band O2 sensor in the exhaust). It then sends this information to the Power Commander V and automatically corrects it while you ride. Each map that we offer has preset Air/Fuel ratio values included that we find to be the best overall settings. This lets you simply plug in the unit and let it do the work.

Complete high quality kit to replace the bearing and seals in the DRZ400 swingarm pivot.

For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.

• Complete assembly, ready to install into the shock body
• Has air bleed holes to help remove air from the oil reservoir during installation
• Double-lip oil seal design keeps out dirt and keeps friction low
• Kits include aluminum body, dust seal, bushing, oil seal, O-ring, internal guide bushing/washer, snap ring, and top-out bumper

Replacement shock link bearings and seals. One kits has all you need to get the job done right. Restores your linkage to new condition for better suspension control and smoother action.

• Race Tech's original bolt-on fork valving system for front cartridge forks
• Triple the flow area of pistons
• Put valving control on the shim stack
• Outstanding tunability; improved control, traction, plushness and bottoming resistance
• Complete instructions, Gold Valve pistons, valving charts, valving shims
• Technical Edge Fork Maintenance and Gold Valve Installation video all included

Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.

Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward. 

Simple to install and completely tunable for all conditions and rider preferences.

These Cogent Dynamic Drop-in Cartridges will vastly improve both the compression and rebound damping of your stock forks. These units have been given the seal of approval by the ProCycle staff for both performance and ease of installation. No disassembly of your forks, no drilling of damper rods. Just change the oil over to 5w and install the DDCs under the springs and hit the trails.

The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.

• Bolt-on shock valving for riders serious about suspension performance
• Improves control, traction, plushness and bottoming resistance
• Improved, long-wearing, low-friction sealing design decreases fade
• Includes complete instructions

Cogent Dynamics has created another winner - the 'World's Edge' shock for the 650 V-Strom the rear end you have wanted for all these years. This unit gives the DL650 excellent control with a firm but comfortable ride, both solo and two-up. This shock is equipped with adjustable damping control so you can customize the action to your preference. Please call for lowering options also if you need them.

The Bling Ring preload adjuster and thrust bearing on the spring make preload changes easy when you fill the bags and add a copilot. Keeping the ride height up can make the difference between a good handling motorcycle and a peg scraping pig. Want to make it easier yet? Add a Hydraulic Preload Adjuster like the stock shock has.

Includes mounting bracket.

  Bikes with ABS require the hydraulic preload adjuster

Because the stock shock cannot be rebuilt and offers insufficient adjustment, Race Tech developed a bolt on replacement shock to cure an under sprung and under-damped stock setup.

Race Tech's G3-S Custom Series Shocks are truly custom with spring rates and valving picked specific to each rider. Each shock is built to order featuring Gold Valves to guarantee a plush feel and great bottoming resistance while also providing more traction than any other setup on the market.

Please include your riding weight, skill level, and type of riding in the order comments.

The chain slider protects the swingarm from contact with the chain. Replace yours before it wears through to the swingarm.

• Made of CNC machined A7009-T6 aluminum
• Finished in anodized titanium-color
• Simple bolt-on application

Aircraft aluminum withstands hard hits from logs and rocks. All mounting hardware and wear blocks included.

Replace your lower chain roller with this high quality roller with 2 sealed ball bearings. The stock roller has no bearings. It's just a plastic wheel riding on a bolt. Ball bearing chain rollers are smoother, quieter and last longer.

These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.

JT Sprockets is the world's leading manufacturer of aftermarket sprockets, constantly raising the industry's standards for quality and service. JT Sprockets are the only sprocket manufacturer using the ultra-durable high carbon C49 steel for rear sprockets.

• CNC machined anodized axle blocks
• Made of A6061-T6 aluminum
• Rotate using the forward and reverse positions, able to offset axle shaft 13mm in reverse position. (Mini size is 11mm)
• Scales on both sides of axle block for easy adjusting

One of the most advanced radiator protection systems available for the DRZ400. These guards feature maximum side and front impact protection by using a combination of CNC machined 6000 series aluminum and 5000 series alloy plate to create a complete system to protect your radiators from virtually every direction. Roost and debris protection is exceptional thanks to the angle fin design that leaves minimal exposure to the radiator core and veins.

Even with all of this protection, cooling airflow is still at its maximum with a front louvered panel built with fins designed to mimic the airflow characteristics of the OEM plastic fins. This panel can be removed easily facilitating cleaning of the radiator.

Three-piece modular construction eliminates the design limitations of one-piece designs. Integrated modular construction- Three piece modular construction allows for greater design flexibility eliminating the compromises inherent with one piece designs. Easy fitment no mods required- Radiator guards can be fitted in approx ½ hour using basic tools. Sold in pairs, but repair parts are available individually.

Can be fitted with 17L safari tank & Acerbis tank 

Will not fit the "S" & "SM" model if thermo fan is fitted

Replace the wimpy stock DRZ400 Skid Plate made from 4mm thick 5083 aluminium plate. Strong and great looking. Leave the stock wings in place and give yourself something that will really stop any damage between the frame rails. Supplied with all the necessary stainless steel clamps and bolts required. Available in polished or with the heavy-duty black polymer coating. Like all he other B&B Bash Plates, these plates have foam or rubber where required to keep things a bit more quiet. This plate fits the E, S, SM & kick start models.

Thick carbon fiber plate with many advantages over aluminum.

The use of anti-ballistic composite material provides a longer fatigue life and greater tensile strength than aluminum.

Composite plates are molded to the exact shape desired, making for a closer fit and a more protective plate.

Composite plates absorb vibration and do not amplify sounds like aluminum plates do.

When hit hard, aluminum permanently deforms, bending frame tubes and slicing into water pumps.

Composite plates will bounce back from hard hits and look great long after aluminum plates give up.

Skid plates protect the side engine cases and the water pump in addition to the frame and the center case.

Designed with a high front to keep mud from building up on the engine.

Mounting hardware included.

• Made from strong and lightweight aircraft aluminum
• Protects vital engine parts from rocks and debris
• Custom fit to your specific bike model
• Oil drain hole for easy access
• All mounting hardware included

• Made from strong and lightweight 4mm thick aircraft aluminum
• Protects vital engine parts from rocks and debris
• Custom fit to your specific bike model
• Oil drain hole for easy access
• All mounting hardware include

Protect the underside of your TW!

• Made from 3/16' Aluminum.
• All Mounting Hardware Included

The ultimate in protection for the bottom of your 650 V-Strom. Constructed from 5mm aluminium 5083 plate. Selected because of its extreme suitability for welding and impact resistance, this material makes a great looking and very strong Bash Plate. This plate extends up far enough to be a great Oil Cooler protector as well. All Bash Plates have a polished finish and have foam or rubber where required.

Protect your frame/paint from scuffs and scratches with frame guards. The DRZ 400 frame guards are made from 2mm 5052 marine grade alloy and CNC machined in one piece for strength. All frame guards are supplied with all necessary mountings and stainless bolts. With a polished finish they look great and are easy to install.

Give your DRZ that factory prepped look and protect your frame.

These frame guards from industry leaders Works Connection are CNC cut and formed from aircraft grade 5052 aluminum. These not only protect your frame from scuff and rub marks from your boots, but also give you a flatter surface for better grip and control with your lower legs. All the necessary mounting hardware is included making these a very simple bolt-on installation.

Constructed of heavy-duty mild steel, SW Motech crash bars are designed to provide maximum protection, optical integration, and high-quality fit and finish.

The new SW Motech Rally Crash bars feature a thicker tubing diameter than the previous guards, extend higher up on the side panels for more direct impact protection, and still work perfectly with the aluminum skid plate from SW Motech.

All components are protected against corrosion by sandblasting and black powder coat. Two high-strength frame mounting points.

The SW Motech skid plate is not compatible with Givi or Hepco-Becker crash bars.

Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

Grab our 5-pack and save both time and money!

Superior Filtration:

This should be the last oil filter you will ever buy. Made from laser cut, medical grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area in many cases. Most good paper filters will pass particles in the 90 to 95 micron range, and some tested, as much as 300 microns. Sand is about 125 microns and a white blood cell approximately 25 microns. Scott's stainless filter catches items down to 35 microns "absolute", which is about 3 times better than most good paper or brass filters. The pleat seam is welded, able to withstand up to 600 degrees in our filter, not glued, like paper filters.

Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.

Grab our 5-pack and save both time and money!

Fresh o-rings to ensure your DR650 stays oil-tight and leak free. Includes one of each: oil filter o-ring, filter cover o-ring and filler cap o-ring

Always a good idea to put in a new set of Oil Change O-Rings at the first sign of any leakage. This package gives you the three most important: oil filter cap and the one behind the filter as well as the one on the filler cap. All are new OEM Suzuki O-Rings.

A pair of factory OEM o-rings for the valve covers. Your valve cover o-rings live in one of the hottest parts of the engine and have a pretty short life. Replace them on your next valve adjustment to prevent oil leaks.

New Bearings for your DRZ400.

If you are in the lower end doing work, new bearings are cheap insurance for all that hard work.

• Hot Rods complete stroker crank assembly includes +4mm stroke for maximum power and performance output.
• Hot Rods constructs their complete stroker crank assembly to meet or exceed OEM specifications for maximum durability.
• Hot Rods stroker cranks are completely rebuildable and have been trued to within 0.001" from the factory.
• The Hot Rods stroker crank increases the stock displacement to 424cc when used with the stock bore piston or 462cc when used with a 94mm big bore kit.
• Main bearings sold separately.

This will not fit the DRZ400 kick start models. Nothing is available for the kick start models.

A high quality cam chain from the folks at Wiseco. New cams, big bore kit, high-mileage motor, you might want to think about a new cam chain. Direct replacement for stock unit.

• Direct bolt-on, ready-to-install cylinder; requires no replating and looks virtually identical to the OEM
• Nickel Silicon Carbide plated for long life
• Honed to exact size for easy piston installation
• Big bore cylinders do not require any machine work
• Come complete with gaskets, cylinder, 94mm piston, rings, pin and clips

Barnett high performance clutch kit includes drive plates, carbon fiber friction plates, and heavy duty springs.

Moose Race Fit Radiator Hose Kit

• Manufactured by Samco® Sport UK – the world leader in silicone hose, with over 20 years experience
• Hand wrapped and 100% visually inspected in the UK
• European grade hi-temperature silicone guaranteed to 356°F
• Smooth flow and improved insulation promotes radiator efficiency and improves engine cooling
• Single-molded, Y-piece hoses eliminate the need to reuse OEM 3-way fitting, which reduces weight and eliminates leak points
• Single-molded, T-piece hoses eliminate vulnerable threaded leak points and reduce weight
• Three layers of reinforcement fabric offer high burst pressures and provide better debris/crash resistance
• Zero block tooling technology results in clear and open hose junctions, free from dangerous and restrictive flashing
• Used by leading MX/Enduro and Off-road racing teams
• UV-stable colors don’t fade with heat or sun and are color matched to OEM brands
• Clamps made from 18/8 marine-grade 100% stainless steel have rounded edges that prevent the clip from cutting into the hose and a non-perforated band prevents clip from biting into the hose
• Kit contains hoses and necessary clamps

State-of-the-art replacement seats, Sargent seats are built on a percision-molded lightweight Polytec seat pan. Sargent's proprietary seat foam (Super Cell Atomic Foam) is their own unique blend of resilience, firmness, and vibration-absorption qualities, making it well suited for long distance comfort and support. Sargent seats are covered in a marine-grade, UV-stablized mildew resistant CarbonFX vinyl. These seats will fit bikes with the stock, IMS, or any other aftermarket fuel tank.

Moose Racing Adventure seat provides improved comfort for your riding adventures, or just commuting around. You choose between the stock seat height, or a low seat height (about 1 inch lower). The durable micro-fiber suede top cover enhances rider comfort and increases stability. Side gripper panels ensure secure seating during aggressive maneuvers. The cover is constructed from smooth marine-grade vinyl and features an embossed Moose Racing logo. It includes a strap kit that enables secure attachment of cargo to the pillion section of the seat.

Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam. On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as similar to stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.

Sargent World Sport Performance Modular Seat System with ZONE SUSPENSION BODY CONTOUR TECHNOLOGY.

Honda Africa Twin, 2016+ (CRF1000L) and Africa Twin Adventure Sport 2018+ (CRF1000L2) with ZONE SUSPENSION BODY CONTOUR TECHNOLOGY.

Transform your Honda Africa Twin and Adventure Sports into a long-distance explorer! Sargent's patented Zone Suspension Body Contour Technology, beautiful hand-crafted upholstery, and high-quality lightweight precision construction make World Sport Performance Seats the best choice for the long-haul.

In addition, this two-piece World Sport Seat offering for the Honda Africa Twin features marine-grade, UV-stabilized, hand-crafted upholstery specifically designed to maximize the suspension qualities of the Super Cell Foam.

This is a high-quality seat cover done by Moose for the DRZ400. This is a replacement cover only, no seat foam and you must install on your existing pan with existing foam. Heavy-duty marine grade vinyl with UV protection for long life. Double stitched for durability too!

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area. 

These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or adventure ride!

Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!

Fits Models/Years:
2004-2007 950 Adv.
2008-2013 990 Adv.
2009-2011 990 Adv. R
2013 990 Adv. Baja

The Foam and Cover Kit is only for the OEM pan. It DOES NOT include the pan.

The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail/stop light function. 3 white LED's are used for license plate illumination.

Included is a set of turn signal brackets that bolt to the mount, but these are designed for a smaller LED type signal with a mounting stud of just 8mm. If you think this might be a problem, look at the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!

NOTE: LED's must be installed on a 12 V DC system!

You may have noticed after adding aftermarket turn signals (especially LED units) that your blink rate has significantly increased. OEM flashers are designed for standard bulbs which draw a few watts each, much more than typical aftermarket bulbs or LED signals. This device is an effective alternative to using load resistors because it consumes considerably less watts, consumes less space, and does not generate excessive heat.

The plug is exactly the same as the OEM unit making swap outs a cinch. No wiring changes, cutting and adding connectors. Just plug it in and you will have a steady flash at the DOT OEM rate regardless of what signal bulbs you use. It is an all solid state design and will blink correctly with loads all the way down to 0.1W / 0.01A.

  Not for any DRZ400 or Royal Enfield Himalayan

This nice piece replaces your plastic sprocket cover and protects your engine case from a chain derailment or failure. The 3/16" (5mm) thick steel plate is adjustable to accommodate 14, 15 and 16 tooth sprockets. Includes mounting hardware.

CNC laser cut from 1/8"5052 aluminum then black powder coated and the logo laser etched in place with the V-Strom 650 logo to really set it off. The laser etched logo will not wear off like a vinyl or screen printed graphic.

Heavier gauge aluminum than other aftermarket guards and better coverage than the stock guard. It also will not crack at the stress points. Uses the stock mounting screws.

• CNC machined front sprocket cover
• Designed to keep mud out of the front sprocket area
• Made of A7009-T6 aluminum

The little tool bag that Yamaha provides behind the side cover is nice, but adding this Tool Tube to your TW will make it easier to carry some real tools! The ABS pipe is plugged on each end with waterproof expanding plugs. It is held to the frame of your TW with powder-coated steel straps and brackets. It provides a storage space of 3" ID x 10-1/2" long. Includes all hardware required to mount to your TW200.

You can now order your Tool Tube with a Locking End cap, mini padlock and keys included, on the exposed end.

If you already have a Tool Tube you can order just the Locking End Cap and lock.

Trails End Adventure Motorcycle Tank Bag by Nelson-Rigg, a lot of bag for a little money.

• V-shaped base to accommodate off-road, dual-sport and adventure motorcycles
• New quick release makes for quick mounting and refueling
• Top quality UltraMax™ polyester with maximum UV protection
• Convenient side pockets to hold smaller items for easy access
• Bag maintains shape, has reflective piping and a lined interior
• Reverse coil zippers help keep out dust and dirt, keeping zippers working smoothly
• Adjustable shoulder/tether strap
• Protective base material prevents slipping or marking
• Clear map pocket is touch screen device friendly
• Fully expandable when more room is needed
• Includes an exclusive Lifetime warranty and waterproof rain cover
• Main compartment measures: 12" L x 7" W x 9" H Standard Config. - 12" L x 7" W x 12" H Expanded
• Holds 12.4 Liters / 16.5 Liters expanded

Giant Loop’s 8-liter Fandango Tank Bag provides easy access to fuel, room enough to pack gear for a day trip or a long-haul journey, and is loaded with rider-friendly features similar to its smaller counterpart, the 6-liter Diablo. With its larger capacity, the Fandango provides riders a convenient way to carry larger items such as a DSLR camera, rain gear, first-aid kit, and more.

The Fandango makes packing a breeze with its handy movable interior divider featuring elastic organizers and a spot for your tire pressure gauge. With a fully lined interior that's compatible with hook-and-loop fasteners and an exterior mesh pocket, you'll have plenty of options to keep everything neat and tidy. Plus, if the weather decides to take a turn for the worse, we include a waterproof Tank Bag Dry Pod™ to keep your sensitive gear safe from moisture!

• Harness Dimensions: 8.5″ wide X 12″ long
• Tank Bag Dimensions: rear 8″ tall, front 5″ tall, 8″ wide
• Volume: 8 liters
• 22 oz vinyl coated polyester Bomb Shell™ reinforced with foam
• Slip-Not and clear vinyl top
• Rubber electronics port
• Water resistant YKK zipper (bag)
• Beefy YKK coil zippers (harness)
• Nylike webbing
• Reflective accents for visibility

This Trekker Top Case is manufactured from glass fiber reinforce polymers ensures high structural rigidity. An anodized aluminum cover is then placed over that to resist weathering. 52 liters in size, there is enough room for 2 helmets. Attaches to your favorite rack with a Monokey fixing system. Available in Aluminum or Matte Black.

• Dimensions: 23.6"L x 18.1"W x 12.4"H
• Volume: 52 Liter
• Max Load: 22 lbs.
• Helmet Capacity: 2
• Weight: 11.44 lbs.
• Color: Brushed Aluminum / Matte Black
• Material: Polypropylene / Aluminum

Siskiyou Panniers combine the convenience of top-loading hard panniers with the performance benefits of Giant Loop’s world-travelled soft luggage. Constructed with flexible, impact-resistant, and waterproof materials, Siskiyou Panniers deliver the ultimate lightweight, rugged, and compressible gear packing solution for on- and off-road motorcycle adventures. Choose the Siskiyou Panniers for multi-day rides when quick, top-loading gear access is a priority.

• Top loading for easy access to 70 liters of storage, including mesh pockets under lids.
• Capacity: 35 Liters per side
• Includes two removable waterproof inner liner Dry Pods™ for 100% waterproof performance in all conditions.
• Adjustable design is compatible with an array of side luggage racks — and they can be mounted without racks on some motorcycles.
• Designed by riders and built for the long haul with rugged yet lightweight materials (weighs just 10 lbs with all included components).
• Multiple attachment points secure additional dry bags and gear.
• Includes two Hot Springs Heat Shield™ kits for rackless mounting on compatible motorcycles.

GIVI Pair of waterproof side bags, 25 liter, Equipped with straps to be placed under the saddle, to allow the hooking of the bags through a double ring system.

Materials:
• Polyester 600D/PU W/R
• Pu inserts and fluorescent yellow reflective piping
• Non-slip PVC on the back
• Flameproof fabric at the base of bags
• Matte black reflective material

As standard:
• Roll closure system to ensure fully waterproof
• Front pocket with zipper
• Shoulder strap for transport
• Handle for carrying by hand
• Waterproof high frequency taped inner lining (IPX5 waterproof grade, withstands heavy rain and extreme conditions)
• Load compression straps positioned on the bottom
• Reflective inserts for greater visibility at night
• Reflective pattern prints for greater visibility

100% Waterproof! Saddlebag Dry Pods update Giant Loop’s Great Basin Saddlebag and Coyote Saddlebag, replacing the Great Basin Dry Pods and Coyote Dry Pods.

Keep gear organized and dry with this set of 3 roll-top inner liner Saddlebag Dry Pods, featuring RF welded seams and air purge valves that make it easy to compress gear by squeezing air out of the sealed Dry Pods. Specifically designed to fit inside every version of both the Great Basin Saddlebag and Coyote Saddlebag – as well as the new Great Basin Saddlebag Roll Top and Coyote Saddlebag Roll Top – Giant Loop’s Saddlebag Dry Pods also can be used anywhere you need high-quality, lightweight dry storage.

Includes two side Pods and one double-ended center Pod. Backed by a Limited Lifetime Warranty against defects.

The set includes a 19mm and a 22mm to hold the axle and nut both front and rear. Each 10 inch forged steel tire iron has a hex wrench on one end. The rounded spoon end minimizes pinched tubes and scarred rims.

High-quality, direct replacement plastic kit includes:

• Front and rear fender
• Side covers
• Air box cover
• Radiator shrouds

Yellow kit is only available with white side covers

  Add-on Headlight cowling fits S and SM models not "E" offroad model

Don't like the low fender on your TW200? The ProCycle High Mount Fender Bracket allows you to mount your fender under the lower triple clamp to create more clearance around your front wheel and drastically improve the look of your T-Dub.

The kit is made of high-quality steel components manufactured in the USA, and includes the bracket and all required hardware.

Don't forget to add a new fender for that supermoto look!

Quality windscreen made from Lucite aircraft acrylic making it more rigid and optically clearer than OEM windscreens

This screen is 5" shorter than stock which reduces buffeting.

Moose Adventure Windscreen

• Made from aircraft-quality Lucite®​ acrylic
• Heavy-duty, optically clearer than the OEM windscreens
• Available in various heights and sizes
• 5" Shorter version reduces buffeting and improves warm-weather comfort
• Made in the U.S.A.

Puig Visor Clip-On

• Suitable for screens with thickness between 3-5mm
• Multi-adjustable visor adaptable to Puig and OEM windscreens
• Visor is mounted by clip-ons and does not need to be drilled to the windscreen
• Visor sizes available include 90x230mm, 100x277mm and 102x325mm

The Voyager Pro GPS is designed for off-road and adventure-riding enthusiasts. The GPS delivers robust features that cater specifically to the needs of riders in rugged and challenging environments. The device integrates with your vehicle, and our patented buddy tracking feature ensures the best-connected experience, whether off-road or on-road. The Voyager Pro is perfect for any adventure. Get yours today!

Key Features of the Trail Tech Voyager Pro:

1. Display: The 4" color glove-friendly touchscreen is visible under all lighting conditions, especially in direct sunlight. The screen is designed to withstand harsh elements and has an IP67 rating.
2. Buddy Tracking: Group Ride with maximum enjoyment. This feature uses radio frequency to track up to 20 riders in a group. Quickly set up your group, customize the rider’s names, and spread out to avoid sucking dust and dirt. Get lost on purpose and hit that “buddy beacon” to notify your group of any riding emergency. Ride with confidence in remote areas; No cellular signal is required.
3. Bluetooth Connectivity: The Voyager Pro can connect via Bluetooth to phones and communication devices, allowing riders to receive texts and calls, stream music, and control these functions through the GPS unit.
4. Navigation and Mapping: The device comes with pre-loaded North American maps, and other regions can be downloaded. It supports GPX file import and export, and users can drop customized waypoints. Load your favorite GEO PDF on the device for the ultimate mapping experience.
5. Vehicle Integration: The Voyager Pro connects using vehicle sensors to display vital ride data such as engine temperature, RPM, battery voltage, speed, and distance.
6. Battery: The device requires a 12V DC power source. Note that you should not leave the Voyager Pro GPS on when leaving the vehicle to avoid a dead battery.
7. Quick Removal Dock: The mounting dock can be locked to secure GPS and allows for quick removal of Voyager Pro from the machine. Buy an extra dock and move the Voyager Pro head unit from vehicle to vehicle. The dock utilizes the AMPs hole pattern for compatibility with various mounts.

Summary:

Trail Tech’s Voyager Pro is a comprehensive GPS solution for all adventure-seeking riders. It is specially designed for off-road harsh, rugged conditions and offers a blend of navigation and buddy tracking with vehicle monitoring features. It is the best rugged GPS on the market.

Genuine Yamaha rebuild kit for leaking or damaged front disk brake master cylinders.

Genuine Yamaha caliper rebuild parts will get your front disk brake back in shape.

Semi-sintered construction contains 30% copper by weight within and organic matrix

This design combines the long life of a sintered pad with less rotor wear common with sintered pads

Includes pads for both front rotors.

These awesome rotors are laser-cut out of a high-carbon content 410 stainless steel, lap cross hatch ground, and heat-treated. The finished rotors are mounted on a floating black steel carrier for durability and strength.

The floating pins are an oversized CNC machined stainless rivet with stainless wave washer to ensure these rivets will not crush like more traditionally used steel pressed rivets. high temp paint is applied to surfaces like cooling holes and edges to provide a clean finished look.

Includes a fresh set of brake rotor bolts.

Savvy DR650 owners will remove the upper chain roller. You can use this stainless steel button head screw to plug the threaded hole. Suzuki did not make the upper roller mount strong enough. If you don't remove it yourself the chain will likely do it for you - along with a chunk of metal out of the frame.

These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!

Comfortable Oversize (or Fat Bar) Handlebars.

• CR High Bend
• Black in color. 
• Made from 5mm, proprietary, 2000 series T6 aluminum alloy for superior tensile and yield strength.
• Lighter and stronger than regular bars
• No-crossbrace allows flex to reduce shock and rider fatigue
• Oversize 1-1/8" diameter base reduces to 7/8" to allow standard-size controls/grips
• Etched alignment marks for fast and accurate positioning
• Bar pad included
• Works with stock controls and cables.

For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8  adapter (sold separate).

Ease the pressure on your wrist during those long highway trips.

ProCycle has developed this unique kit to work with your OEM bars and controls. Just flip the thumb lever down to apply enough friction to hold the throttle in place.

Customize the power characteristics of your bike by simply adding an altered ration cam. The Control cam allows smoother more controlled throttle while the Quick cam lets you put the power to the ground quickly.

Throttle Lock Kit Includes:

• Billet aluminum throttle tube with standard cam
• Vista Cruise Throttle Lock
• All mounting hardware
• Tension adjustment tool

Replacement shift lever from IMS with folding tip.

With this upgrade, you can avoid having to keep new replacement cotter pins on hand every time you adjust your chain.

The new Fastway Evolution AIR foot pegs are now the ultimate pegs in the Universe.

Designed and sculpted out of the best 7075 Billet aluminum by Pro Moto Billet elite engineers and machinists. Featuring Fastway's Patented adjustable height, traction, and camber options, the Evolution AIR footpegs are superior in every way.

Fastway Evolution AIR pegs are designed to shed mud and debris, while being ultra strong.

This is the ultimate adventure bike platform, it measures 2.25" wide, 4.75" long.

Patented adjustable collars make it easy to run them in the 'standard' or 'low boy' positions on most bikes.

Gain more room for bulky boots, or for longer legs. Fastway Adventure pegs come with two sets of F3 cleats, one standard, one long. Kamber bolts lets you adjust the 'tilt' of your pegs to increase comfort, or to give better squeeze on your bike.

New from Warp 9, top of the line Adventure Pegs. a full 5" long and 2.5" wide will give your feet the perfect perch whether you are cruising down the highway or standing up hammering down a singletrack trail.

• Ceracote coated Chromoly steel pivot for the ultimate in strength
• Replaceable 7075 T6 Aluminum Platform
• Permanent Stainless Teeth provide the ultimate in non-slip traction
• Built-in bottle opener in the bottom!

Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.

Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.

• Wide 60mm platform
• Widest and lightest pivoting pegs on the market
• Open design = less mud packing
• Unique multi-directional grip pattern
• Outstanding build quality
• Race proven design and durability

This is the evolution of taking the proven GPRV1 steering damper and locating it under the handlebars. Mounting the damper unit under the bars allows for addition room on the top cross-bar or bar mounts.

This GPR setup is a good choice for the weekend warrior to the race professional that would like to raise the handlebar height. Perfect for desert and off-road GPs.

Make it easy to pull the rear axle out of your V-Strom. This little handle goes into the hollow axle and then tightens down to give you a handle so you don't have to tap it out from the other side.

Evans Waterless Coolant (EWC) can be used for all water cooled motorcycles to eliminate overheating. With a boiling point in excess of 375° F, it will not vaporize, thus eliminating overheating, boil-over and after-boil. At the other end of the spectrum, EWC freezes below -40° F.

EWC also delivers more power by eliminating pre-ignition and detonation caused by overheating, thus improving combustion efficiency. It also generates very low vapor pressures which reduces strain on cooling system components. EWC comes in 1/2 gal. containers.

  Installation requires specific procedures. Please refer to the instructions.

Mapping America's Back Roads

Amazingly detailed, large-format topographic & street map atlases of all 50 U.S. states. Unbeatable recreational information & detail.

 Map detail includes:

• Back roads, dirt roads and trails
• Elevation contours
• Remote lakes and streams
• Boat Ramps
• Public lands for recreation
• Land use / land cover – forests, wetlands, agriculture
• Trail heads
• Campgrounds
• Prime hunting and fishing spots

Limited to stock on hand

Driven Engine Block-off Plates will stop the annoying and possibly damaging backfires from occurring while allowing you to remove a few pounds in associated valves and hoses from your bike. On late model EFI bikes with O2 sensors, ESPECIALLY when using Dynojet's Power Commander 6 with the Autotune feature, the air injection system MUST be blocked as it will introduce additional oxygen into the system which will skew your O2 sensor's values and make it impossible to get a correct tune.

Showa removed the schrader valve on many newer rear shocks. Now you need a needle to recharge your shock with nitrogen after a rebuild. Race Tech built this unit just for that job.

The features of this tool include 300 psi capacity, bleeder valve and T-handle plunger pin chuck. Swivel chuck has a 12" flexible hose. Comes complete with instructions, carrying box and Schrader valve extension (required on some Showa shocks). Nitrogen bottles available at any welding supply house.

Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.

This is a weatherproof protectant for wiring and electrical connections. Goes on as a liquid and dries to a vinyl polymer that resists dirt, dust, chemicals and moisture, ensuring that connections stay intact. Brush-top applicator allows coverage without gaps and enables access to tight spaces that roll tape and shrink tubing can't get to.

Goes on wet but solvent evaporates to leave a dry moly film. This unique dry film won't attract dirt or dust, is highly resistant to water, prevents rust and corrosion. It is the perfect lubricant to use on brake and clutch cables. Includes applicator needle to get into cables, locks and anything else that needs dry lubrication.

• Synthetic spray wax technology
• Outstanding gloss, clarity, depth, and slickness
• Use on any hard surface including plastics, rubber, glass, chrome, paint, and fiberglass
• Fills minor scratches and cob-webbing

High quality blind bearing puller you will be proud to use and own.

• Includes 8, 10, 12, 15, 17, 20, 25, 30, and 35 mm collets
• Collets are precision machined for perfect fit and durable performance
• Collets have a innovative new design that improves durability and pulling strength
• Pull tests in our lab show our collets are 2x to 3x stronger than conventional collets
• Kit includes high quality slide hammer designed by Motion Pro with excellent weight and balance
• Slide hammer and individual collets are also available separately from Motion Pro
• Lifetime limited warranty

Givi Smart bar for attachment of electronics.

Bike specific mounting hardware (sold separately) required.