It's never too early to start thinking about the next calendar photo contest. Submit your photos here all year round to be considered in next years calendar and maybe win a prize too!
This is the ultimate in radiator guards! It will protect your fragile radiator from nasty front & side impacts.
This ultra tough guard is constructed from 1/8" aluminum and is easy to install.
All Flatland Racing radiator guards have rear mounting brackets for that extra support! All Mounting hardware is included.
The Race Tech Gold Valve allows you to tune both compression and rebound valving for vastly improved performance.
- Bolt-on shock valving for riders serious about suspension performance
- Improves control, traction, plushness and bottoming resistance
- Improved, long-wearing, low-friction sealing design decreases fade
- Includes complete instructions
These thumb-screws replace the stock headlight adjustment screws. These adjusters make it much easier to keep your headlight aimed properly. This is even more important if you are running the HID headlight as it is very easy to dazzle oncoming traffic if your headlight isn't aimed correctly.
- Sold in pairs.
An aluminum Light Mount for your bike. Put whatever light you like up front for more light as well as great daytime visibility to other vehicles. Win-win situation. Choose the Single Mount or Double Mount.
B&B Off Roads Auxiliary single light bracket is made from 5mm 5083 structural plate. It was designed to suit a 6 " light bar. Add an auxiliary bracket and LED light to help Improve visibility whilst night riding.
- Designed to fit with standard tank only
- Will not fit with Australian Safari Tanks
For a top notch rebuild or re-valve of your rear shock use this high quality replacement seal head.
- Complete assembly, ready to install into the shock body
- Has air bleed holes to help remove air from the oil reservoir during installation
- Double-lip oil seal design keeps out dirt and keeps friction low
- Kits include aluminum body, dust seal, bushing, oil seal, O-ring, internal guide bushing/washer, snap ring, and top-out bumper
These heavy-duty aluminum brackets are laser cut from 0.190" 5052 Aluminum then powdercoated black. Designed specifically for mounting auxiliary lights to the front of your DR650, the mount goes between the fender and the lower triple clamp. Longer fender bolts are included in each kit. installs in 10 minutes.
Three options are available: two different dual mounts that place the lights outside the fender and a single, center type mount. The 2" mount is for smaller type lights and is 8-5/8" between the mounting holes while the 3" is 10-3/8" between the mounting holes. If you are going to use larger style lights, the 3" mount is for you.
Note! The Dual 2" and 3" mounts do not work with the Acerbis 6.6 gallon tank! They make contact prior to full lock. Mounts are fine with other oversize tanks.
Lose that ugly stock taillight and license plate bracket and install this tidy one from ProCycle. We designed this unit and have it manufactured here in Oregon. Kit includes a LED taillight / brake light unit as well as compact turn signals. We also include splice connectors and split tubing, everything you need for this installation.
There is also an option to include matching front turn signals with side mount brackets that allow you to replace the clunky front signals with the same style as the rear in this kit.
Now available in the original version or the Ultra version. The original uses the front two emitters for low beam and then switches to the rear two emitters for high beam. The Ultra uses the front two emitters for low beam and then runs all 4 emitters on high beam at a reduced wattage. Wattage is 38 watts on low and 38 watts on high.
This bulb uses 4 Cree XHP 50 emitters, capable of more than 2500 lumens each. At 5000 lumens on each function, this is the brightest Cyclops H4 bulb.
- All metal construction for bases and collars
- Better thermal efficiency
- Better beam pattern distinction between high and low beams
- 5600k
- 38 watts
- Removable metal base plate for easy install.
- Screw on connectors at driver
- Standard H4 connector
- High/Low Beams
*UNIVERSAL PART, PLEASE CHECK YOUR APPLICATION FOR FITMENT
This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a plug and play installation however a small amount of trimming on the backside of the plastic headlight shroud is required.
This is the best performing and highest quality headlight they currently offer. The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive). The high beam is amazingly bright eliminating the need for auxiliary lighting.
The materials, construction, and aesthetics are all top notch. You won’t be disappointed.
Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive
The Trail Tech Vapor Speedometer/Tachometer units are custom designed for an exact fit. They feature a bright white backlit LCD display, waterproof connections, and all parts needed for a complete installation. These units accept AC and DC power input, and automatically switch to internal power if external power is removed. Power connectors are included. Permanent solid-state memory guarantees that data is never lost, even without power. Units are available in black.
Trail Tech provides a one year warranty and unlimited free phone and email support.
Unit functions:
- Speedometer
- Current Speed
- Maximum Speed
- Selectable MPH/KMH Display
- Tachometer
- Real-Time RPM Bar Graph
- Numeric RPM Readout
- Dual Programmable Shift Lights
- Up to 20,000 RPM
- Temperature
- Ambient Temperature
- Engine Temperature (liquid cooled only, optional air cooled sensors available)
- Dual Programmable Temp Lights
- Distance
- Adjustable Distance
- Permanent Odometer
- Selectable Mile/Kilometer Display
- Clock
- Hour Meter, Stop Watch, Ride Time
- Accumulated Ride Time
- Permanent Hour Meter
Give your DRZ that factory prepped look and protect your frame.
These frame guards from industry leaders Works Connection are CNC cut and formed from aircraft grade 5052 aluminum. These not only protect your frame from scuff and rub marks from your boots, but also give you a flatter surface for better grip and control with your lower legs. All the necessary mounting hardware is included making these a very simple bolt-on installation.
Stock bore replacement pistons from Wiseco. You have your choice of the standard compression ratio of 12.2:1, or a high-compression ratio of 13.5:1.
This high-compression kit will run perfectly with standard pump Premium.
Kits include piston, rings, wrist pin and circlips.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series DRZ400S/KLX400S rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
- Great for carrying cargo, duffel bags/backpacks, and mounting Pelican, Seahorse, or any other hard cases. Givi compatible.
- Holes are in place to accept Rotopax mount with no drilling required.
- Stainless steel mounting hardware and instructions included.
- Fabricated with mild steel, MIG welded, and finished with a semi gloss black industrial grade powder coat.
- Weighs 3 lbs, 10 inches wide, 12 inches long.
- Works with stock tool bag. You can remove the seat with no interference from the luggage rack.
- Rear rack only, no Rotopax mount or side racks included.
- Includes aluminum cylinder, piston kit, and special gasket set designed for larger water jackets
- Bolts on with no machining required
- 94mm big bore piston
- Aluminum cylinder designed with wider water jackets for better cooling.
- Forged hi-compression piston 12.8:1
- Includes all necessary Rings, Clips, and Gaskets.
New wider seat to help keep comfortable on that long commute or dual sport ride. The added width and foam density will help keep the seat from being an item to stop you from going on that ride or enjoying the bike.
The new updated 2.0 version has a sleeker shape and a better fit in the tank area.
Complete Seats come assembled on an aftermarket pan and ready to ride.
Width: | 9 1/8" (232mm) |
Height: | 1" (25mm) Lower than stock |
This CNC cap will replace the stock gas cap on the stock tank. You do need some parts from the stock cap, so don't throw it away yet! It is not difficult and this kit includes the additional hardware required. Also included is a vent tube with a matching cap.
For use on STOCK TANK ONLY! This is NOT a locking cap.
Does not fit California model DR650
Steel braided lines have a Teflon tube as a core wrapped with a stainless steel wire braided exterior which doesn't allow the brake lines to stretch under pressure like stock rubber lines do.
The benefit is a firmer brake lever with better feel because the energy that was going into stretching the stock lines now goes straight to the brakes.
No longer need your speedo drive? Install an electronic unit? This CNC machined aluminum unit will replace the stock speedo drive on the front wheel keeping things properly spaced and sealed up.
To suit a 20mm Axle.
Before placing your order please ensure you check the diameter of the axle, as the earlier models may have different sized axles.
A stainless steel front fender brace. Helps stabilize your front fender.
Gives additional strength for carrying a fender mounted tool bag.
Fits on top of the fender and bolts between the fender and bottom triple clamp. Stainless steel won't rust or corrode. Includes hardware.
Requires you to drill one hole in the fender for mounting.
Transform your ride
Now there is wind protection for on and off-road use with no compromises! MadStad's new rotating dual-sport windshield brackets put the windshield where you need it for street riding, but tuck it down out of the way for off-road. Adjust the height and angle for much smoother airflow, better wind protection and a more comfortable ride than any fixed windshield can provide, and it's not in your face when you want to hit the trails.
Their complete drop-in system is custom-made for your bike and includes everything needed to mount and position the shield. Your bike will not require any modification.
What's included in the kit
- A set of MadStad dual-sport adjustable brackets
- The acrylic windshield
The MadStad brackets bolt to your fork clamps putting the windshield just in front of your instrument cluster for street riding, with adjustability for height and angle. The rotation feature allows you to shift the shield forward and down through 7 different settings bringing it down in front of the head light and out of your way. Their custom knobs lock the brackets in their multiple positions so the shield stays where you want it to, even bouncing around off-road.
Front fender from ProCycle Plastics (formerly DSA) is shaped very much like the OEM DRZ400SM front fender. Big enough to be functional without wind-steering the bike like the stock fender does. Vacuum molded, these are a design improvement over stock. These are fully compatible in any combination with the original factory plastic.
Emulators make damping rod forks perform like well-tuned cartridge forks. Emulators are tunable valves that sit inside your forks on top of the damping rods and are held in place by the fork springs. Simple to install and completely tunable for all conditions and rider preferences.
ProTaper's ADV handlebars give you a bar taller than most with extra space on the control portion of the bar. These bars provide an additional 20mm of space next to where your levers and throttle are located for your GPS, phone cradle, auxiliary switches, etc . They come in Adventure (which is taller than stock) and Adventure High (which is even taller).
These are oversize bars, which means they are are 1 1/8", not the smaller 7/8" diameter. Therefore some bikes will require a adapter and there are several available to select from.
Using the same manufacturing techniques and materials as ProTaper’s industry-changing 1⅛" motocross handlebar, the EVO Adventure is specifically designed to provide adventure/touring riders with the increased comfort and control they need. With over 8" of straight section in the control areas, mounting vital components is made easier than ever. With its premium 7000 series aluminum alloy construction and computer-profiled four millimeter-thick wall design, the EVO Adventure Handlebar is up to 25% lighter and 45% stronger than competing handlebars.
- 1⅛" tubing at the clamping area
- Exclusive 4 mm-thick 7000 series aluminum alloy for superior tensile and yield strengths
- Optimum balance between fatigue life, impact strength, and impact-absorbing flex
- High-tech shot peened, stress-relieved, and anodized finish for unmatched durability
- Independent lab tests show that the EVO Handlebar leads the market in fatigue life
- Epoxy inner coating resists corrosion
- Chemically applied cut lines and alignment grid are scratch- and peel-resistant
- Plastic bar end plugs keep the elements out and provide a stronger base for grip ends
- Weighs only 1.55-1.7 lbs. (720-780 grams), depending on bend
New wider seat to help keep comfortable on that long commute or dual sport ride. The added width and foam density will help keep the seat from being an item to stop you from going on that ride or enjoying the bike.
The new updated 2.0 version has a sleeker shape and a better fit in the tank area.
Complete Seats come assembled on an aftermarket pan and ready to ride.
Width: | 8" (203mm) |
Height: | Same as OEM |
CNC machined from 5mm aluminum 5083 plate with lots of slots to attach your Rok Straps (or other straps). This gives a considerably wider deck than the standard B&B Rack. Attaches directly to the B&B rack with four screws that are included. Available in either polished aluminum or a black polymer coating.
These plates are pre-drilled and countersunk from the bottom making installation of a RotoPax mount quick and easy.
Some older carry racks will not have predrilled holes in them to mount luggage plate in which it will require you to drill yourself (select pre2018 version)
This is for the add -on Top Plate only.
Fits B&B Luggage Rack purchased AFTER 2018
The B & B Eng. DRZ400 Bash Plate is made from 4mm thick 5083 aluminium plate. Strong and great looking, this is the top of the line protection plate for the DRZ. Supplied with all the necessary stainless steel clamps and bolts required. Available in polished or with the heavy-duty black polymer coating. Like all he other B&B Bash Plates, these plates have foam or rubber where required to keep things a bit more quiet. This plate fits the E, S, SM & kick start models.
Their baffle was designed to replace the stock insert. The baffle produces a nice note compared to the de-restricted stock version and dyno test results showed an increase on 2 hp up top.
A noise test on the insert was conducted at the EPA Victoria Vehicle Test Station at Macleod under controlled conditions with Class 1 meters.
Tested Bike | ADR Signature dB(A) & test RPM | ADR tess with B&B Tip |
---|---|---|
Suzuki DRZ 400 | 93 dB(A) @ 3375 RPM | 97 dB(A) @ 3375 RPM |
Some extra details:
- The ADR test is conducted at an engine speed which is 50% of the engine rpm at which the engine develops maximum power. However, this engine speed is determined when the bike is in restricted form, with a throttle restrictor that stops the throttle being fully opened. This is why the ADR engine test speeds are so low. However, they are the engine speeds used to determine compliance.
- On the ADR test, the B&B tip was over the signature noise emission, but a tolerance of 5 dB(A) is allowed before prosecution would be initiated. With this tolerance, the insert would not be prosecuted as it is just 4 dB(A) over the signature.
- When tested with the standard OEM tips (as fitted when delivered from Suzuki Australia), the Suzuki came in at 95 dB(A) for the ADR test
Does not contain a spark arrestor. Check local laws on spark arrestors before purchase.
GoldPlug is the gold standard in engine protection.
Stainless steel drain plug with an extremely strong magnet that picks up metal flakes in your oil.
12mm Thread
It is a good practice to replace your sealing washer with every oil change. These 10 piece kits are made up of 5 Copper washers and 5 Aluminum washers. The manufacturer recently decided to make half of the kit Copper washers as that is the material of choice for many OEM manufactures. This gives you the opportunity to decide which you prefer, but either will work great at creating a leak-free seal between the case and the drain plug.
Clymer repair manuals provides step-by-step procedures based upon the complete disassembly of the motorcycle. This hands-on experience combined with extensive research results in a manual that is both user-friendly and detailed. Hundreds of original photos and illustrations guide the reader through every job.
- Hot Rods complete stroker crank assembly includes +4mm stroke for maximum power and performance output.
- Hot Rods constructs their complete stroker crank assembly to meet or exceed OEM specifications for maximum durability.
- Hot Rods stroker cranks are completely rebuildable and have been trued to within 0.001" from the factory.
- The Hot Rods stroker crank increases the stock displacement to 424cc when used with the stock bore piston or 462cc when used with a 94mm big bore kit.
- Main bearings sold separately.
This will not fit the DRZ400 kick start models. Nothing is available for the kick start models.
The Q4 employs intricate chambers, baffles and proprietary multistage packing material making it the best performing quiet muffler available.
Constructed from aircraft grade aluminum and high strength stainless steel.
Sound output 96dB. Several pounds lighter than the stock muffler.
Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Head and mid-pipe are constructed from 304 stainless steel. Entire unit is pounds lighter than stock and gives great horsepower and torque gains throughout the RPM range.
All handmade in the USA with a 1 Year Limited Manufacturers Warranty.
The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels.
Need to remove your clutch assembly? This holder is the quickest and easiest tool out there to get a grip on that hard to handle hub. Laser cut to the exact pattern that EBC makes their clutch plates from, it makes loosening and re-tightening the clutch nut easy. All of that and no worries about doing any damage to your expensive clutch hub.
Race Tech shock springs in a wide range of spring rates to dial in your rear suspension to suit your weight (stock spring is 5.3 kg/mm). Recommended spring rates:
Rider Weight w/gear lbs. | Spring Rate |
---|---|
100 or less | 4.6 |
100-124 | 4.8 |
125-149 | 5.0 |
150-174 | 5.2 |
175-199 | 5.4 |
200-224 | 5.7 |
225-274 | 6.0 |
275 + | 6.3 |
Yoshimura RS-3 that will slip right on to your stock header. Made by hand to the highest quality standards using the championship-winning racetrack experience and their extensive R&D facility ensure these pipes perform and will last.
Both full systems and slip-on mufflers include 96 dB sound insert/USFS approved spark arrestor installed in the muffler. Mid-pipe is stainless steel while the stainless RS-3 oval muffler design has a slim profile with an aluminum end cap.
Works on OEM header only!
High-quality, direct replacement plastic kit includes:
- Front and rear fender
- Side covers
- Air box cover
- Radiator shrouds
Yellow kit is only available with white side covers
Add-on Headlight cowling fits S and SM models not "E" offroad model
The race-bred RS-2 exhaust has proven to be extremely popular among rider looks for a combination of performance and value. It enhances performance dramatically, provides an enviable exhaust note and offers the unmistakable look and sound of Yoshimura. RS-2 mufflers feature a straight baffle that leads to a single turn-down machined aluminum end cap.
All models have a USFS Approved spark arrester in a oval-shaped sleeve with a large volume of packing material.
Remove the bulky stock number plate holder with our slim design- comes with LED number plate light.
- Quick and easy install
- Mounting hardware supplied
- Comes with clear LED tail, brake & number plate light
- No mods required for installation
- Available in polished or black PPA coating.
- Pre drilled to suit Australian licence plate
*Please Note: Brake light does not come with necessary/factory connectors. Some cutting, crimping, soldering of wires may be required for connection.
More range at a great price.
The 3.6 gallon tank is for the off-road DRZ400 and DRZ400E.
The 3.9 gallon tank for the dual-sport DRZ400S. The 3.9 gal tank also fits the ES and SM models.
Both tanks are available in a selection of colors.
NOTE: Clarke tanks do not come with a vent hose or vent cap.
The Powercore 4 spark arrestor muffler. FMF developed the Powercore 4 to increase the horsepower and torque throughout the entire power curve. Highest quality packing for long life. Removable spark arrestor included. Louder than the Q4. Approximately 99db stock or about 94db with optional Quiet Insert installed.
- Uses long-life muffler packing for increased packing life
- Forest Service approved spark arrester
Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
You pay $3.50 per filter with our value 10-pack!