We are now accepting submissions for this year’s Calendar Photo Contest! Please upload your images here by 9am Pacific on September 16, 2025.
A complete kit to rebuild and refresh your stock carburetor. Kit contains Genuine Mikuni replacement parts.
**Due to varying model requirements, this kit does not include main or pilot jets.
Repair leaking carburetor or worn out float needle assembly.
The Phillips screws in Japanese motorcycles are not really Phillips screws. They are actually Japanese Industrial Standard (JIS) screws that are very easy to strip with Phillips head drivers.
Is the cylinder head intake boot on your DR650 cracked or weathered, is it missing parts of the lip to seal around the carburetor, have you recently pulled the intake boot off only to realize the O-ring behind it is hard & brittle? This kit is your solution to solving some of those mystery problems and make your bike like new again. There can be a great deal of heat that can radiate behind the cylinder head on a DR650 as it is an air cooled engine. With that comes long term maintenance items that will need to be replaced due to them being made of materials that cannot withstand those constant heat cycles indefinitely.
Our kit includes O.E. parts from Suzuki to include:
This kit includes 2 Needles that have been developed by JD Jetting and manufactured for them to their exacting specifications. These two needles allow a wide range of tuning possibilities and provide correct fuel delivery at any throttle position.
4 allen type screws for the float bowl are also enclosed should you strip out the stock screws during your tuning process. Complete instructions with photos, jetting suggestions for different set-ups and situations, 5 Main Jets and a drill bit complete the package.
Now you can have minimum output shaft wear, minimum chain drive wear with the FRITZCO DRIVELINE sprocket. The design of their sprockets provide correct chain alignment, allows for full spline contact with the XR650L's output shaft, fit the counter shaft either way, and straight up no hassle installation with the OEM two bolt retainer and fasteners (except 13 tooth that comes with it's own quick change retainer). Their sprockets are machined from alloy steel that is comparable in every way to OEM Honda and the best offered by other manufactures. The sprockets are then given a heat treatment that provides a compatible sprocket for the Honda output shaft and longest wear life possible.
A way to double the sprockets life would be to have a sprocket that fits on the shaft either way so both sides of the teeth can be used. Bear in mind you can't wear one side of the teeth all the way through, then flip the sprocket, and expect double life. You must reverse when a normal wear pattern develops.
16 tooth sprocket is the biggest front sprocket that will run with the standard 110 link chain and 45 tooth rear sprocket on an XR650L
The OEM cover will require modifying to use the 16 tooth sprocket on your XR650L.
Quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
Quality steel front sprockets. Choose 525 or 520. Also available 'Wide Boss' JTF438 520 sprockets.
All 520 sprockets require a new retainer plate, please add on if purchasing this size.
High quality sprockets
Counter shaft sprocket replacement requires the removal of the left side case cover. A new gasket may be required. This is also a great time to replace that leaking oil seal!
Individual 14T, 15T or 16T front sprockets.
JT Sprockets are made from the latest generation of computer design and control metal cutting equipment for maximum durability. Front sprockets are made from chromoly SCM420 steel alloy. All sprockets are heat-treated and hand-finished to meet or exceed the highest possible quality standards.
Reduce the friction dragging down your drivetrain. This chain roller is made from Delrin®, it's self-lubricating and a significant improvement over stock.
Does not use a bearing but rides directly on the frame boss. There is no mounting hardware included.
A real Heavy-Duty Chain Guide manufactured from 5mm (3/16") thick 5052 Aluminum. This guide will take a pounding and continue to put that chain right on the sprocket. The rub block is machined from UHMW plastic and can be positioned to fit just about any sprocket available for the DR. These are powder coated black for a great look and additional protection.
Chain guides are subject to wear over time due to friction produced by chain movement. To restore optimal performance, replace them with this authentic Yamaha component.
Chain sliders undergo performance degradation over time due to the friction experienced by the chain. To maintain optimal functionality, it is recommended to replace worn components with genuine Honda parts.
High Quality chain. You'll need to cut to fit your sprocket combination.
Non O-ring, Clip Style Master link
High Quality chain. Will need to be cut to fit your sprocket combination.
Lower friction and longer life. X-rings have twice the sealing ability as compared to o-rings. They do a better job of keeping the lube in the links and the dirt out. DID VX chains have a reputation for being the best chain you can buy for dual sport riding. DID VX chains come with rivet type master links.
Replace those worn out brake pads with quality EBC replacements.
GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 2 |
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 2 |
Wheel bearing kit contains all of the bearings and seals required to re-fit a wheel.
Wheel bearings typically fail from water and dirt contamination. These wheel bearing were developed in partnership with KML Bearing and is designed for the difficult operating environment of the Power Sport industry.
Premium EMQ quality, hi-speed-bearing featuring low drag, double lip rubber seals which provide superior exclusion of water, dirt and to improved grease retention.
Type TC Nitrile Elastomer wheel seals are specifically designed to keep out water and dirt.
Packed with Chevron SR1-2 high-performance grease with rust and oxidation inhibitors.
The rubber coated outside diameter creates an optimum seal at the hub.
Steel garter spring guarantees constant pressure on the axle shaft over the life of the seal.
| Description | QTY per Kit |
| Ball Bearing | 2 |
| Seal | 2 |
Replacement Inner Tubes for your VanVan or TW200. Always a great idea to carry a spare on your adventures as the rear tube is often hard to find.
Shinko 700 Series tire features an aggressive 60% on-road and 40% off-road read pattern for good dirt riding performance, without sacrificing pavement grip. Other features:
The GP-1 Dual Sport Tire from IRC is designed to provide the best possible handling and control for both on and off the pavement. Special knobs penetrate loose surfaces for excellent traction, braking and cornering off the road yet won't wear off as fast as a full knobby when used on the street. Features include:
Available for Front 3.00x21 only
Made for the true adventure rider, the K784 has everything you need to get you anywhere on or Off-Road.
This street-legal knobby from Pirelli has good stability and cornering precision thanks to the carcass stiffness. The tread pattern optimized for use on dirt and gravel roads, cross-country racing and desert tours. It has lasting off-road performance and knob tearing resistance due to the special off-road compound.
Motoz Tractionator Desert H/T series of tires are renowned for great traction and long wear life. These tires are designed to handle hard terrain, fast and rocky trails as well as gravel roads and desert hard pack. Tricky off-cambers, ruts and hard braking at extreme lean angles are no problem for this DOT approved tire.
Note: Tubes can be run in Tubeless tires, but a Tube Type tire cannot be run Tubeless.
Kenda's Dual-Sport tire designed for the 80% on-road, 20% off-road crowd.
The TCK70 combine rugged off-road ability with balanced street performance. Unique tread block pattern makes this tire quiet and stable on the road yet still agile on gravel. Combined with a MultiGrip semi-dual compound technology allows different levels of tire 'hardness' on the central tread and tire shoulder for extended mileage and improved cornering grip.
Tires listed are all standard Bias Ply tires unless noted with an -R after the size.
All of the TKC70's are Tubeless Tires. However, tubes can be used in Tubeless tires.
A highly refined blend of aluminum, copper and graphite lubricants. Use during assembly to prevent galling, corrosion and seizing due to weathering or chemicals. Anti-Seize assures easier disassembly. Temperature range: -60°F to 1600°F (-50°C to 870°C). Salt, corrosion and moisture resistant – ideal for marine use. Meets Mil Spec #907E.
Replacement folding shift lever, stock length made by IMS.
These versatile Risers allow you to clamp a 7/8" diameter handlebar or you can remove the 7/8" reducers and then clamp an 1- 1/8" aluminum "fatbar". If you are thinking of going to a fatbar after you bend your stock set or just want the versatility and option to run any bar, this is the riser to go with. Reducers lock into risers to insure no slippage between components.
These risers use 8mm bolts. Always check and confirm that your bike has adequate cable and brake line length before installing any handlebar risers.
Anti-Vibration Risers may interfere with aftermarket large capacity fuel tanks, and some steering stem clamp configurations (in these cases we recommend using standard pivoting risers).
Throttle cable routing on the XR650L gives you very little extra slack for raising the bars or adjusting them towards the rider. We now offer throttle cables that are 3" longer than stock allowing you to customize the bar position to your riding style.
These quality cables are made by Motion Pro.
Keep your motor running right with fresh spark plugs!
NGK is one of the world's largest manufacturer of spark plugs, whose products are used as original equipment (OE) on countless motorcycle and automobile models.
This kit provides much of the performance gain of our 130 kit but keeps you legal for racing classes that do not allow motors over 125cc.
This kit provides much of the performance gain of the more expensive 150 (143cc) kits. But gives better reliability due to the thicker wall of the cylinder sleeve.
Cycle Racks Bag Supports can used for many different Cycle Racks and can be used on either the front or rear rack.
When they developed these, they wanted a functional, yet "Easy On- Easy Off application. The pig tail hook goes up, over and underneath the bar of the rack, they can also be used upside down on the rear rack as side boards. To install them, wing them out, slide them in place and then wing them back down. Simply reverse the process to remove them.
Rok-Straps are supplied to secure them in place. They are pre-drilled to accept the pattern of the Roto-Pax Pack Mount (sold separately) so you can carry fuel or attach them to your own bags.
They are sold together in a set of one right support and one left support.
COLOR: Black
Steel cargo rack from Moose Racing. It features a nice wide platform and a durable powder coat finish. 17" wide and 10" long.
Their rear racks are great for adding the extra storage needed for your next adventure. They are the perfect size for a backpack or small duffel bag. Their steel racks are built to handle any riding style you throw at them, now Rotopax ready! This is the ENDURO Series CRF450L rear rack which measures 10 inches wide and 12 inches long.
Easy to Install
CycleRacks are made out of steel tubing, bent in a press, and welded together in a jig. All of their racks have the same platform, 18" wide by 12" deep. Includes lower mount hardware.
All of their products are 100% made in the USA. If the rack is ever broken for any reason, CycleRacks will replace it for free, you just pay the shipping.
Race Tech HP Springs have a high stiffness-to-mass ratio. In other words; the springs are light weight for their particular spring rate. This requires the finest materials and processing. Shot-peened and pre-set so they cannot sack out. All Race Tech HP Springs have the highest rate tolerances in the industry. These are the finest springs in the world-guaranteed.A stiffer shock spring will help you get through the whoops or just help handle that extra baggage on the rear.
Stock spring rate is 10.5 kg/mm
Spring color may vary due to specification requirement and availability.
The complete shock upgrade kit - a shock spring of your choice, Race Tech Gold Valve kit, detailed instructions and a bottle of quality shock oil to complete the job. Everything you need to transform your mushy stock shock into suspension that really works.
Recommended rates:
The correct spring rate for your weight will give a smoother more controlled ride. No more bottoming out, and improved traction and confidence off-road.
8.6 & 9.6 springs require an adapter which is included.
Recommended rates:
*Spring color may vary due to specification requirement and availability.
Race Tech shock springs in a wide range of spring rates to dial in your rear suspension to suit your weight (stock spring is 5.3 kg/mm). Recommended spring rates:
| Rider Weight w/gear lbs. | Spring Rate |
|---|---|
| 100 or less | 4.6 |
| 100-124 | 4.8 |
| 125-149 | 5.0 |
| 150-174 | 5.2 |
| 175-199 | 5.4 |
| 200-224 | 5.7 |
| 225-274 | 6.0 |
| 275 + | 6.3 |
A CNC machined fork brace to stiffen up the notoriously wimpy front end on the DR. Have more confidence in your front end on or off the pavement.
Split design means that installation takes minutes without having to remove the forks. Available in a black anodized finish.
The complete fork upgrade kit - Race Tech springs and emulators. Also includes a set of top quality fork seals and fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.
Progressive springs offer a soft initial spring rate for a plush ride. Progressively wound design provides increased resistance to bottoming as spring compresses. These springs are significantly stiffer than the wimpy stock springs.
They will make a big improvement in front fork action while still delivering a smooth ride. Sold in pairs.
Hard anodized oval shaped aluminum muffler with a TIG welded reinforced muffler bracket and red powder coated stainless steel end tip. Sleek muffler design gives you lots of clearance and it has a removable screen-type USFS approved spark arrestor. Head and mid-pipe are constructed from 304 stainless steel. Entire unit is pounds lighter than stock and gives great horsepower and torque gains throughout the RPM range.
All handmade in the USA with a 1 Year Limited Manufacturers Warranty.
New design gives you more protection and uses OEM mounting points for easy installation.
Yes, plastic! This is a product from our friends at Acerbis. Ultra tough injection molded reinforced composite. Flexible Heavy-Duty Polypropylene will not effect chassis ability to flex, will not effect handling.
Made to bolt in factory mounting points, no frame modification needed
It's twice as thick as a metal skid plate but is only half the weight. Plastic glides over rocks and roots better than aluminum. It also reflects less engine noise.
From JNS Engineering, a super solid Rear Master Cylinder Guard for the XT250, WR250R and X. CNC formed and then powdercoated black for lost lasting corrosion protection. Did we mention how good it looks? All hardware provided.
You want a lighter replacement for your heavy steel stock tank? Don't need the extended range (or bulk) of a big tank? The 3.7 gallon tank from Clarke might be just right. It's almost 5 lbs lighter and holds close to 1/2 gallon more fuel than stock to increase your range by about 20 miles. Fits with your stock petcock, Pingel or Raptor petcock.
Get better range from your XR650L by adding a Clarke 4.7 gallon fuel tank. Cannot use stock shrouds.
Available in Natural, White, Black, and Red. Natural color is recommended if you wish to easily see the fuel level in the tank. Includes cap, uses stock petcock.
More range at a great price.
The 3.6 gallon tank is for the off-road DRZ400 and DRZ400E.
The 3.9 gallon tank for the dual-sport DRZ400S. The 3.9 gal tank also fits the ES and SM models.
Both tanks are available in a selection of colors.
NOTE: Clarke tanks do not come with a vent hose or vent cap.
A replacement Clarke Gas Cap that fits most Clarke Gas tanks. Comes with rubber gasket.
If you need a replacement cap for your Acerbis tank, why not go bling? These caps have a carbon fiber pattern molded into them that is extremely realistic. Looks like the real thing. Topping off the cap is a CNC Machined metal vent cap. This eliminates the need for a lengthy vent tube that gets in the way. The vent cap allows air to vent into the tank but does not allow fuel to splash out during normal use or during a tip over.
These caps fit Acerbis tanks only.
This CNC cap will replace the stock gas cap on the stock tank. You do need some parts from the stock cap, so don't throw it away yet! It is not difficult and this kit includes the additional hardware required. Also included is a vent tube with a matching cap.
For use on STOCK TANK ONLY!
This is NOT a locking cap.
Does not fit California models.
Replacement brush plate kit fits both original stock or aftermarket starter motor.
ProCycle Dashboard designed to power multiple electronic devices. It can also be used for accessory lights, heated grips or gear, whatever you like. You can also use the two pre-drilled holes to attach a RAM mount and place your phone or GPS unit on that while charging.
The dash panel is manufactured from laser cut 5/64 mild steel and powder coated black. Also included are 2 weather resistant green LED rocker switches, a voltmeter with two 4.2 amp weather resistant USB ports, a wiring harness with a built in 20 amp fuse/holder, and complete instructions. Everything you need to mount it and connect the outlets back to the battery.
**If you would like the Voltmeter & USB ports to be powered by a "key-on" power source, add the "Auxiliary Power Plug" adapter to your order and you will be able to connect the positive and negative terminals directly into the aux plug behind the cowling for a quicker and easier installation as well.
New Hot Shot Suzuki Stator: aftermarket stator is made with heavy duty components and is a direct replacement for OE# 32101-32E01 or 32101-32E00.
This stator will provide your bike with 20% more power (240W) to support your added gear. Whether you have heated grips or you're running multiple aux lights, this unit will give you the power that you're looking for.
Used for DC conversions, this product allows a Trail Tech NiMH battery pack to mount to the vehicle.
Note: Not for use on bikes with electric starters.
Small 12 volt 3700 mAH NiMH (Nickel-Metal Hydride) battery used for DC conversions, it mounts to the bike and is recharged by the bike’s electrical system.
Dimensions: 1.5" X 3" X 3.8" Weighs only 20 ounces.
Note: Not for use on bikes with electric starters.
This box moves up the rev limiter allowing higher revs. It also has a hotter advance curve from the OEM box. This allows for a bit crisper throttle response and easier starting.
State-of-the-art replacement seats, Sargent seats are built on a percision-molded lightweight Polytec seat pan. Sargent's proprietary seat foam (Super Cell Atomic Foam) is their own unique blend of resilience, firmness, and vibration-absorption qualities, making it well suited for long distance comfort and support. Sargent seats are covered in a marine-grade, UV-stablized mildew resistant CarbonFX vinyl. Available in standard height and 1" lower than stock. These seats will fit bikes with the stock, IMS, or any other aftermarket fuel tank.
| Width: | 11" (279mm) |
| Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a plusher ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
Complete seats are built by Seat Concepts on a new seat pan and come ready to be installed on your bike.
| Width: | 10" (254mm) |
| Height: | Same as OEM |
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
On this model, they built up the front of the seat, but dished out the rear slightly to level out the angle of the rider platform, and reduce the slope-into-tank feeling of the stock seat.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or Dual-Sport ride!
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Available as a Foam and Cover Kit for OEM pan. It DOES NOT include the pan.
| Width: | 12.5" (318mm) |
| Height: | Same as OEM |
ADV Sushi is a webbing reinforced velcro strap with integrated daisy loops. These are as handy as zip ties and duct tape. This is one of those products that you will use frequently if you have them with you.
A single strap was load tested at 200 pounds before it let go and a single strap held 50 pounds overnight with no issues.
Use this kit to build your custom solutions such as a fuel bottle holster, spare tube carrier, or use them to attach your bags to your Uprising Soft Rack. The possibilities are truly endless.
This Kit Includes:
Ride in warm temperatures a lot? Worried about your motor oil just getting too hot? The Trail Tech Universal Fan Kit mounts up to the backside of the DR's oil cooler to draw cool air across it and keep those oil temps down. An electronic temperature sensor mounts to the fan, no need to cut any fluid lines, and automatically turns the fan on when needed to keep the temperature in the optimum range.
The activation sensor can be set wherever you like to keep the temperature right where you want it. Backlit for easy viewing anytime it also includes a volt meter.
Kit Contents
This device will pulse your brake light automatically. There are over 1000 possible pattern combinations with individually programmable Flash Speeds, Pre-Delay, and Flash Durations, as well as a disable feature to disable the unit. This device gives the end user the widest range of possibilities for customizing your tail light safety flash. With simple programming setup using only your brake lever, their is no disassembly or removing of the seat required to change the programming on the device.
Features:
This auxiliary light harness is specifically built for the DR650 using the highest quality materials and components. Wire lengths, component locations, and end terminals are all predetermined and assembled for you. No electrical expertise needed! The relay is wired directly to the battery and Posi-Tap connectors are used to tap in to the existing headlight high beam circuit.
This eliminates the need for a separate switch to operate your auxiliary lights. When your high beam is on, your auxiliary lights will be too. Back to low beam and those high-powered beams will be off so you don't bother oncoming vehicles. There's also an in-line fuse holder for safety and peace of mind. A simple one page instruction sheet is included.
This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.
Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.
This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.
Triangle/Teardrop style signals with LEDs. Mounts on any flat surface to keep out of the way of brush, branches, and your exhaust system. Requires LED flasher or LED turn signal resistors to flash properly.
This kit includes a DOT LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
How does this headlight compare to our original TW200 kit? First and foremost, this kit has SAE/DOT markings and a much wider/brighter high beam pattern. The low beam is very similar to our original kit: wide, flat, and bright but with more punch. The DOT headlight assembly has also proven to be more durable than the original headlight.
Low Beam: 30W, 2,800 Lumens
High Beam: 50W, 3,600 Lumens
Color Temperature: 6,000k
DOT & SAE Approved
CE, RoHS, ISO9002, IP67
No cutting, drilling, or wiring modifications! Installation takes 5 minutes.
Two colors to choose from, Chrome or Black. Light output and beam pattern is the same for either color.
Please note that this product is not compatible with the 1987 TW200.
This kit includes the all new Morimoto 4×6 LED headlight and pre-assembled JNS Engineering adjustable mounting bracket set. It’s a one beer, plug & play installation.
This is the best performing and highest quality headlight they currently offer.
The low beam pattern is bright, very uniform, and features a proper upper cut-off (Left Hand Drive, ie USA).
The high beam is amazingly bright eliminating the need for auxiliary lighting.
The materials, construction, and aesthetics are all top notch. You won’t be disappointed!
Low Beam: 20W, 2,400 Lumens
High Beam: 35W, 4,300 Lumens
Color Temperature: 5,000k
DOT Compliant
Beam Pattern: Left Hand Drive. (USA)
This DOT kit includes LED headlight assembly with plug-and-play wiring harness, a specially designed adjustable steel mounting bracket, and all the required installation hardware.
No cutting, no drilling, no wiring modifications! Installation takes 5 minutes.
This kit is highly recommend over the non-DOT kit. The low beam has extra punch and a proper beam pattern cut-off. The high beam throws light far and wide. It’s already a crowd favorite!
Two colors to choose from, Chrome or Black. Light output and beam pattern are the same for either color.
JNS has come up with another great addition for the little XT250. Auxiliary light mounts that keep the lights up high for great projection, but still good and tight to the bike for protection. These heavy duty 1/8" stainless steel mounts put your lights out of harms way without interfering with controls, body work, or the fuel tank. Includes four longer upper triple clamp bolts. Everything but the lights themselves to light your way through the darkness.
Low peg mounts from JNS Engineering. Your choice of a straight 1.5" drop or get that drop and a 1" rearward offset. You can use your stock pegs or click on one of the optional pegs that are made to fit the stock DR650 mounts.
These heavy duty steel mounts are pressed, welded and then powdercoated black for protection. Includes mounting bolts.
Note: These mounts are compatible with the SW Motech Center Stand by adding a 1/8" spacer behind the mounts.
These low peg mounts will drop your footpegs 1.5" and move them to the rear 1" for a much more comfortable riding position, especially for taller riders. Unlike relocation plates, these mounts do not hang dangerously below the frame. You can mount stock or aftermarket pegs and they are compatible with all skid plates, crash bars, and center stands.
New 10.9 high strength mounting bolts are included. Once installed the foot controls will need adjustment and the brake switch spring will need to be slightly modified.
Pegs that are designed for real adventure, providing a level of comfort not seen with other pegs. 2.25" by 3.5" makes for a platform that you can stand on for long periods with no worries. All necessary parts included for a direct bolt-on application.
Available only in clear aluminum for durability and protection from the elements.
Double the size of your side stand footprint and half the chances of your XR650L tipping over when parked on soft terrain. This laser cut, TIG welded 0.190" thick slice of aluminum bolts to your machine with just the addition of a hole in the stock side stand pad. Just takes minutes to mount! All hardware provided.
Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.
This set of high quality replacement steering stem bearings includes:
Maier headlight cowling in colors to match the ProCycle body plastics kit for the DR650.
New Body Plastics available in Black, White, Carbon Fiber, Dark Blue, or Yellow.
Also, Currently Exclusive to ProCycle: Olive Green, and Desert Sand (complete kit only)
Includes Rear Fender, Side Panels, Headlight Cover, and Front Fender.
Choose a Kit with Maier Front Fender [pic1] or after market SuperMoto Fender (black or white only) [pic2].
Formerly DSA, now ProCycle brand, is a plastics kit in three colors - Black, White, and Blue, as well as Blue fenders with White side panels and Black fenders with White side panels. (headlight cowl not included).
Vacuum molded, these parts are a design improvement over the stock pieces. The side panels have a crisper, more angular look than the stock parts while the front fender is shaped like the DRZ400SM OEM front fender. Big enough to be functional without wind-steering the bike like the stock fender does.
Kits include front and rear fenders, a new LED tail/brake light and license plate holder, and both side panels.
Add a fresh new side panel hardware kit and an adhesive heat shield for a fresh off the showroom floor look.
Add a Maier Mfg. headlight cowl if you are doing a complete color change to your DR (must select plastic kit with head light cowl option)
Freshen up the look of your TW. New Plastic in Black or White. Includes Rear Fender, Side Panels, Headlight Cover, and Front Fender.
Choose a Kit with OEM Front Fender or after market SuperMoto fender.
SuperMoto fender kit includes our High Mount Fender Bracket!
Includes new Suzuki side panels, heat shield, headlight cover, rear fender and your choice of aftermarket off-road or supermoto front fender.
Choice of off-road or supermoto (SM) front fender.
Blue kits come with white side panels.
Factory Replacement Body Plastics from Kawasaki
Universal design comes undrilled without mounting holes, allowing it to be custom fit to your bike.
Vents in the back improve airflow to motor. Smaller front reduces 'wind steer' and improves high speed stability.
Refer to pictures for color and fender design.
Quality replacement headlight fairing for Gen 1 KLR650.
Available in 4 colors.
Stock Suzuki choke knob holder guide. Replace your cracked or cross threaded stock unit with a new one.
RotoPax holder made to mount a single Fuel and/or Water container.
Need to mount two containers? A water and a fuel? Two waters? Get the extender which allows you to stack two containers no problem! Single mount, two containers
Don't get burned! Giant Loop's ingeniously simple and effective exhaust shield protects bags and bodywork from heat damage. The Hot Springs Heat Shield helps avoid the meltdown, preventing bags and side panels from touching your bike's exhaust. It's the lightweight, universal heat problem-solver for virtually any motorcycle exhaust system. Backed by a Limited Lifetime Warranty.
Hydraulic Clutch Bleeder Kit includes 2oz of Magura Blood clutch fluid, 2 bleeder tools and fittings to properly bleed your hydraulic clutch. Great if you have air infiltration in the system or damaged it in some fashion.
