XR650L

These Sequential Turn Signals are available in a 2 pack or 4 pack short stem with 7 LEDs.

Matte Black, plastic body with smoke lens and 8mm mount bolt.

Specifications

• E-marked.
• Short Stem: 75mm x 15mm

Triangle/Teardrop style signals with LEDs. Mounts on any flat surface to keep out of the way of brush, branches, and your exhaust system. Requires LED flasher or LED turn signal resistors to flash properly. 

• Fits on the fender with screws for secure installation
• Rubber mount base fits even curved surfaces
• Terminals and bolts are included for installation
• Comes in pairs
• Works on 12V AC/DC

This Diode Kit is only necessary if you have a single dash indicator for your turn signals. One dash light for both left and right signals (such as on the DR650).

This kit allows power to flow in just one direction from the LED signals to the dash indicator light regardless of which direction you are signalling.

You may have noticed after adding aftermarket turn signals (especially LED units) that your blink rate has significantly increased. OEM flashers are designed for standard bulbs which draw a few watts each, much more than typical aftermarket bulbs or LED signals. This device is an effective alternative to using load resistors because it consumes considerably less watts, consumes less space, and does not generate excessive heat.

The plug is exactly the same as the OEM unit making swap outs a cinch. No wiring changes, cutting and adding connectors. Just plug it in and you will have a steady flash at the DOT OEM rate regardless of what signal bulbs you use. It is an all solid state design and will blink correctly with loads all the way down to 0.1W / 0.01A.

  Not for any DRZ400 or Royal Enfield Himalayan

This type of flasher is required for LED turn signals. For DC (battery) systems only. Includes 2 female connectors for universal fit.

  Not compatible with any DRZ400

Works on AC and DC lighting systems

  Not compatible with any DRZ400

The SignalMinder unit is designed as a plug-in accessory for many Japanese bikes. SignalMinder uses a microprocessor to cancel the turn signals at one of three selectable time outs; 10, 20 or 30 seconds.

You can also make it so that all four of your signal lights also act as running lights and establish a dual-channel system on your bike. With the dual-channel system, when you activate the RIGHT turn signal three times in succession, you get 4-way hazard flash lights.

Connecting the 12 volt supply from the brakes to the SignalMinder, also allows for a brake flash option.

There are many options and configurations using this electronic tool.

No wire cutting required. The kit includes Scotchlok connectors to tap into existing wires.

Allows LED type turn signals (and low wattage flush mounts) to flash using a standard flasher unit. Connectors included. One kit works with 4 signals.

The Barkbusters 10 OHM Resistor Set for LED Indicator Lights will correct the flash rate of your auxiliary signal lights. Ready to plug in connectors make installation a breeze. These resistors are intended for Barkbusters LED Indicator Lights.

Features:

• 10 OHM
• Intended for Barkbusters LED Indicator Lights
• Corrects flash rate of LED signals
• Flash rate: 90 (+/- 30) times per minute

This devices allows any two wire after market LED turn signal indicators to operate as running lights (always on), and will blink on / off when the turn signal switch is activated. It is highly recommended to use this product with the Fixed Rate Turn Signal Flasher. This device, as well as aftermarket turn signals, use much less current than stock turn signals, thus an increased flash rate will occur. Load resistors or a fixed rate turn signal flasher will get your flashers operating at the normal flash rate again.

Each package contains two separate adapter boxes, good for operating both turn signals, left and right of either the front OR rear of your motorcycle. You will need to purchase a 2nd kit if doing the Front AND Rear of the motorcycle.

This device is universal; designed to work for any motorcycle with a DC electrical system. Kit comes with bullet connectors to wire in manually. Works with any two wire non-sequential aftermarket LED turn signal indicators.

• Eliminates the need to cut and splice wiring when using aftermarket turn signals or marker lights
• Plug into the OEM turn signal plug and then use bullet style connectors used on aftermarket lights
• To verify proper fitment, compare connector photos to OEM connector
• Sold in pairs

These turn signal relocation brackets from ProMoto Billet provide an easy way to move the stock turn signal lights, useful if you find them getting in the way of your luggage configuration.

These brackets may utilize an existing hole in some of the rack side brackets, though many applications will require drilling or fabricating in order to mount properly.

Replacement Halogen bulbs for mini style turn signals. Sold in a pack of 5 bulbs.

Roll-up pouch ideal for tucking away your lights when out on the trail.

Taillight and brake light Attaches to the top of the rear fender. Dimensions: 3 1/2" wide x 2" long x 3/4" tall. D.O.T. approved.

LED powered taillight, brake light, license plate light & license plate mount. Attaches to the underside of MX style rear fenders.

Taillight, brake light, & license plate holder (no plate light). Attaches to the underside of MX style rear fenders. Small and good looking!

Taillight, brake light, & license plate light. Attaches to the top side of enduro style (XR, KDX, etc) rear fenders. Dimensions: 2 3/4" x 4 3/4" x 2 1/2" tall. Wiring instructions included.

Taillight, brakelight, turnsignals, license plate light & license plate mount. Taillight is DOT approved, turn signals are not. Attaches to the underside of MX Style rear fenders. Turnsignals are embedded in the taillight housing. Wiring instructions included.
*Flushmount signals may require resistors to flash correctly

Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on 12-24 volt DC circuits.

Has both high and low beams. Attaches to the upper fork tubes with rubber straps. DOT and CE approved.

Here is an adjustable height centerstand from T-Rex Racing. If you are running supermoto wheels or lowering links, this centerstand will be much easier to use.

T-Rex stands are made from steel tubing finished in black powder coating for durability. Back by a 3-Year limited warranty for any material or manufacturing defects. Rest assured that you are getting best material commercially available.

Greatly eases basic chain maintenance, tire changes, parking, cleaning, etc. All necessary hardware is included. Installs using basic hand tools.

Revolutionize your riding experience with Swiftkicker.
An adjustable kickstand for your motorcycle. Swiftkicker is built for offroad motorcycles, dual sports, and dirt bikes. Designed with the idea in mind that motorcycles should be able to take you anywhere, the Swiftkicker motorcycle kickstands help you do just that. You can set the length to anywhere in a six inch range of travel so you can stop anywhere without having to worry about having an even surface to park.

With just a flick of your toe, you can adjust the kickstand to the desired height, park your motorcycle, and be on your way. 
No longer will you have to search for a rock or piece of wood to prop your motorcycle up with, or even worse, coming back to your bike to find it has tipped over from unstable ground.

The Swiftkicker is 100% manufactured in the USA from the highest quality components. 
The billet 6061 head and the hard anodized tube are significantly stronger than the stock stand. An oversized foot will assure that the end of your stand stays where it belongs, rather than eight inches underground with your bike lying on top of it. The design is trail proven in the harshest possible conditions. Because nothing is indestructible, any of the kickstand components are replaceable at a lower cost than purchasing an OEM kickstand.

Measured from the center of the pivot to the bottom of the foot.

• Standard length travel range is 13.5"-19.5" (the middle of the travel is approximately the same length as the stock stand)

Double the size of your side stand footprint and half the chances of your XR650L tipping over when parked on soft terrain. This laser cut, TIG welded 0.190" thick slice of aluminum bolts to your machine with just the addition of a hole in the stock side stand pad. Just takes minutes to mount! All hardware provided.

Inexpensive way of getting the factory look. Adds 1/2" of width to any standard foot peg. These will give you a much more stable platform when standing on the pegs.

Sold in pairs.

Not your average rubber insert! These rubber covers go over the top of your MK3 or MK4 Pivot Pegz so that the aggressive teeth are only exposed when you need them in muddy conditions.

• Unique, innovative design
• Wide flat platform
• Openings allow mud/dirt to pass through
• Easy and quick to get on/off
• Good grip
• Reduced vibration
• Extra comfort

Important to verify which style Pivot Pegz you have before ordering.

The IMS Pro-Series foot pegs are made of stainless steel and are hard coated to prevent drooping. 

They are the original Cast 17-4 Stainless steel pegs that revolutionized the foot peg market.

These pegs are 50mm(1.95") x 78mm(3.1"). 

The IMS Super Stock pegs are the perfect choice for both the daily commuter and the rider-in-training. Their mellow tooth design keeps you planted while preventing wear on your soles. They are also perfect for young riders who don't need or want a more aggressive option. 

Wider foot pegs for sure-footed comfort. 

17-4 cast stainless steel.

• Each footpeg is cast, heat treated, and hardened from 17-4 stainless steel, given a solution annealing treatment, and age hardened for superior strength
• Width (57 mm) and length (90 mm); slightly convex platform for better boot positioning and grip when leaning forward or back
• Dual plane teeth provides traction without the "stuck" feeling
• Made in the U.S.A.

• Durable steel wide foot pegs.
• Made of chromium molybdenum steel for extreme durability.
• Black powder coating finish

Services two Pivot Pegz and fits MK2, MK3 and MK4 Pivot Pegz

Kit Contents:

• Two pivot tension springs
• Two lock nuts
• Two washers
• Six o-rings
• Two split pins
• Pivot Pegz sticker and instruction sheet

Pegs that are designed for real adventure, providing a level of comfort not seen with other pegs. 2.25" by 3.5" makes for a platform that you can stand on for long periods with no worries. All necessary parts included for a direct bolt-on application.

Available in a beautiful anodized black or clear aluminum for durability and protection from the elements.

Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty. Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever!

• Wider, lighter, stronger design
• Widest (mm) and lightest pivoting pegs on the market
• Upgraded heavy duty, long life springs
• Unique multi-directional grip pattern
• Outstanding build quality
• Lifetime Warranty*

Tapered roller bearings provide decreased maintenance, less wear, smoother operation and longer life.

This set of high quality replacement steering stem bearings includes:

• Upper and lower tapered bearings
• Upper and lower bearing races
• Upper and lower seals

• Designed to quickly and precisely remove outer bearing race from the steering head without the use of a hammer and punch
• Puller design ensures bearing is pulled perfectly straight to eliminate possible damage to frame
• Works on all tapered bearing races from 47 mm to 55 mm OD
• Precision machined anodized aluminum cup will not damage seal surface
• Brass bearing washers for easy use and long life
• Hardened steel jaws engage securely on inner bearing lip
• Lifetime limited warranty

Upgrade your Honda XR650L with a Subframe Brace Kit, designed to enhance strength and rigidity for your bike. This complete kit connects the frame and subframe, reinforcing the structure to support increased load capacity—perfect for riders using side cases, top cases, and rear racks.

Key Features:

• High-Quality Materials: Attachment points are machined from 6061-T6 billet aluminum for superior strength and durability.. The 6.5mm thick support bars are laser-cut for a perfect fit.

• Easy Installation: No cutting, drilling, welding, or modifications required for installation. Easy 20 min installation.

• Enhanced Load Capacity: Provides added rigidity and support to the subframe, improving bike stability when carrying additional gear.

• Exhaust Compatibility: Compatible with both STOCK Exhaust and FMF Exhaust systems.

High Quality chain. Will need to be cut to fit your sprocket combination.

Always carry a spare master link when out on the trail.

  Master links are not interchangeable. Be sure to check the manufacturer and series on your chain.

These do not fit the TW200 or XT250. Only for 520 or 525 chains, Please verify chain size.

Quality steel front sprockets. Choose 13T through 15T. The stock size for the XRL is 15T. Go down in tooth count for faster acceleration.

This retainer is has a no hassle installation for quick change sprocket swaps with simple readily available tools (pliers and screw driver).

This spring clip retainer takes the place of the OEM two bolt retainer and fasteners when a FRITZCO sprocket is used.

Designed for OFF ROAD USE with the thought in mind that you can ride to your favorite off road spot using a 15 or 16 tooth sprocket and larger than stock rear sprocket. Then quickly change to the 13 tooth and enjoy the ripping torque provided by the huge amount of reduction the 13 tooth offers. Making the XRL much better in the technical stuff. You will really be surprised how much better a big bike like an XRL handles off road with low gearing.

This retainer can only be used with FRITZCO sprockets and can not be used with thin OEM type sprockets.

Now you can have minimum output shaft wear, minimum chain drive wear with the FRITZCO DRIVELINE sprocket. The design of their sprockets provide correct chain alignment, allows for full spline contact with the XR650L's output shaft, fit the counter shaft either way, and straight up no hassle installation with the OEM two bolt retainer and fasteners (except 13 tooth that comes with it's own quick change retainer). Their sprockets are machined from alloy steel that is comparable in every way to OEM Honda and the best offered by other manufactures. The sprockets are then given a heat treatment that provides a compatible sprocket for the Honda output shaft and longest wear life possible.

A way to double the sprockets life would be to have a sprocket that fits on the shaft either way so both sides of the teeth can be used. Bear in mind you can't wear one side of the teeth all the way through, then flip the sprocket, and expect double life. You must reverse when a normal wear pattern develops.

16 tooth sprocket is the biggest front sprocket that will run with the standard 110 link chain and 45 tooth rear sprocket on an XR650L
The OEM cover will require modifying to use the 16 tooth sprocket on your XR650L.

Quality steel rear sprockets.

Color may vary based on manufacturer availability, quality will not be compromised.

This kit will replace your stock sprocket bolts and nuts with new hardware.

Factory Honda replacements in a convenient kit.

Chain guards experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.

Chain guides experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.

Chain guides experience degradation over time as a result of chain friction. To ensure optimal performance replace worn components with genuine Honda parts.

Chain sliders undergo performance degradation over time due to the friction experienced by the chain. To maintain optimal functionality, it is recommended to replace worn components with genuine Honda parts.

Chain slippers undergo degradation over time due to friction associated with the chain's movement. To maintain optimal operational performance, it is advised to replace worn components with authentic Honda parts.

• Accurately and quickly measures chain slack
• Two scales measure both chain slack and chain to swingarm clearance
• Setting chain slack properly dramatically improves chain life
• Lightweight compact design fits easily in your tool box or road kit
• Works on most street and dirt bike applications up to 75mm chain slack
• Made from engineered nylon with aluminum measuring scale
• Anodized laser-etched precision measuring scale
• Refer to your owner's manual for proper chain slack and procedure
• Patent pending

Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.

Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box.

The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!

• PBR = press, break, rivet
• Innovative design will press, break and rivet 520, 525 and 530 chains with one convenient tool (not for use on 428 chains)
• Versatile design will remove chain pins, press master-link plates and rivet hollow nose and soft nose (quad stake) master link pins on O-Ring and non O-Ring type chains
• Easy-to-use design allows you to change tool functions by simply moving the position of the anvil block
• Indexing letters on movable anvil and body ensures correct tool configuration; simply line up the letter on the anvil to the letter on the body to get the configuration you need
• All components conveniently store on tool when not in use
• All steel construction with heat-treated components for strength and durability
• May be supported in a vise or held with included handle
• Great for the professional technician or DIY mechanic
• Compact and light enough to carry in a tool bag for trail-side repairs
• Patent Pending

Can break or rivet chains from #35 to #530 like a pro.

kit includes a 2mm, 3mm, and a 4mm pin to fit most chains.

kit includes press plates,and all necessary riveting pieces and comes in a durable plastic case.

NOTE: when breaking a chain, YOU MUST grind the heads off of both pins on a link first.

This is without doubt the fastest, most effective, most meticulous, precise and systematic method for giving your chain a thorough cleaning. It forces its bristles between the plates where dried and hardened chain lube, road sand, glass, tar and other materials gather to form a hard shield of abrasive dirt where the O-ring meets the chain plates. 

• Chemical resistant nylon brush
• Flexible and adjustable
• 360 degrees of cleaning
• Compact size for easy storing

Note: Designed to be used with the engine off

Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets.

• Will not harm O-ring chains
• Easily adjustable for all chain sizes

Introducing Oinker®, the revolutionary chain lube attachment for dirt bikes, street bikes, and ATVs. Say goodbye to messy lubrication. Oinker® attaches to any chain lube or wax, ensuring a precise and even application to both sides of your chain. This means minimal overspray, keeping your swing arm, rear tire, and brakes clean.

• Even and Accurate Lubrication: Their patented dispenser features exit holes that align with your chain's link plates, ensuring the areas that need it most get it.
• Minimize Over-spray: Keep your motorcycle clean and free of messy chain lube.
• Reduce Waste: No more over-lubing your chain. Their patented dispenser enhances the efficiency of your lubricant use.
• Rotatable Dispenser: Allows you to adjust your hand positioning. Ideal for bike's with chain guards.
• Durable: Constructed from glass-filled nylon, Oinker is strong, durable, and resistant to chemicals.
• Universal Compatibility: Fits any standard can of lubricant.

*For cans with an attached smart straw, you will need to replace it with the included nozzle

What's Included:

• 1 Chain Oiler
• 3 aerosol straws
• 3 replacement nozzle to be used only on cans that have attached straws.

Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.

This Motion Pro press tool is a must have when installing and removing Clip-Style master links (520, 525 & 530 sizes).

Easily presses on and off master link plates, works on 520, 525 & 530 Clip-Style master links.

Maximum master link width 24.8mm.

Will not damage master links, hardened steel pins for reliable use.

Light weight billet aluminum construction.

A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate.

Fits 520, 525, and 530 pitch chain.

ULTIMATE SPROCKET WRENCH KIT

• 12” long wrench gives you more torque to get those thread locked sprocket bolts off easily
• Double ended 12mm & 13mm to fit all modern motocross, Enduro and dual sport bikes
• Dog leg wrench design allows wrench to easily clear rim edge and wide tires
• 8mm allen fits most Japanese bikes 8” long for extra leverage
• Torx T45 fits late model KTM and Husqvarna bikes, 8” long for extra leverage
• Vinyl coated handles to protect rim edge and give a non slip grip
• Makes routine sprocket bolt maintenance a quick and easy job

• Hardened metal rotor/disc locks resist cutting, sawing and chisel attacks
• Comes with carry pouch and a disc lock reminder cable
• Includes an extra mini flashlight key for three total keys
• Features a durable push button lock with high security anti-drill round key lock cores

The ABUS SmartX 8078 3D Alarm Disc Lock offers advanced Level 18 security, combining cutting-edge technology with exceptional protection for your bike. 

Featuring a 13.5mm double-locking sliding bolt made from specially tempered hardened steel, it delivers superior resistance to tampering. 

The 3D motion-sensing alarm emits a powerful 100dB sound to deter unauthorized movement, while the SmartX Bluetooth keyless lock system provides ultimate convenience. It seamlessly connects to the ABUS SmartX App, allowing you to monitor lock, alarm and battery status in real-time. 

The USB-C rechargeable battery ensures long-lasting performance and multi-color LED lights with audible signals keep you informed. The lock also features location memory from the last pairing, providing added peace of mind.

• Level 18 security
• 13.5mm double locking, sliding bolt
• 3D motion sensing alarm, 100db
• SmartX blue tooth, keyless lock system
• Connects to ABUS SMARTX APP for lock / alarm / battery status 
• Lock constructed from specially temper hardened steel
• USB-C rechargeable battery
• Multi-color LED light and audible signals inform about battery and lock status
• Location memory from last pairing

Made with heat-treated carbon steel for longer wear life and reduced galling. Stock size, simple bolt-on procedure.

• manufactured from unique ebc low carbon hpsr steel
• laser & cnc punched for lightness
• hardened and ground for precision braking
• nickel coated to resist corrosion

High quality carbon steel brake rotor.

A great option for every day use, or on your spare rear wheel.

• manufactured from unique ebc low carbon hpsr steel
• laser & cnc punched for lightness
• hardened and ground for precision braking
• nickel coated to resist corrosion

Full braking power for your XR650L supermoto conversion. Floating EBC 320mm brake rotor with gold anodized alloy carrier. Includes caliper relocation bracket.

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered pads are high performance race pad with superb durability similar to that of the sintered pad. Higher friction level and fade resistance. Diamond ground surface finish to speed bed-in. Comes with new pad pins. Race Sintered are designed for racing use only; not for street use

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered pads are high performance race pad with superb durability similar to that of the sintered pad. Higher friction level and fade resistance. Diamond ground surface finish to speed bed-in. Comes with new pad pins. Race Sintered are designed for racing use only; not for street use

• Sintered Pads are best for regular riding. Long life, and good performance in all conditions
• Sport Carbon pads are made for fast riding in dry conditions. Not recommended for mud, water, or sand
• Race Sintered are designed for racing use only; not for street use

Includes front and rear brake pads

GBrakes Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.

The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.

• Significantly improves response and feel over factory rubber lines
• Largest performance improvement for your money over any other braking upgrade
• Stainless steel hose resists abrasion and puncture
• Teflon core does not degrade over time like rubber lines
• PTFE Dupont 64 Teflon® hose
• Feature a heavy-duty stiffener sleeve and route just like the factory lines
• Proprietary, premium fittings
• Banjos utilizes a unique machined channel and sealing surface for leak-free installations
• R&D and engineered in the USA
• GBrakes USA controls the manufacturing process, ensuring the highest level of quality control

Factory Honda replacement for your worn out lower cable guide.

Each kit includes all necessary rubber components and brake pins.

Each kit includes all necessary rubber components and brake pins.

All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.

Made by Nissin, an OEM supplier in Japan

All the parts you need to freshen up your brake master cylinder. New piston, seals, return spring, boot and snap ring.

Made by Nissin, an OEM supplier in Japan

Replacement retaining pin for the brake caliper. Includes 1 stock style brake pin.

Be sure to use some anti-seize on the threads when you install it.

Front caliper only for DR350 and DR650

This anodized billet piece, brings a touch of color to your bike. Available in red or blue, it replaces the stamped steel clevis that connects your brake pedal to the master cylinder.

This brake bleeder makes bleeding your brakes a one man job.

The unique check valve allows fluid and air to escape while preventing air from re-entering the system.

Combines wrench and bleeder valve into one convenient and compact tool

• Fits most 8 mm bleeder nipples
• Bleeds brake systems and hydraulic clutch systems
• Internal check valve for fast easy bleeding
• Anodized billet aluminum handle with chrome moly steel body
• Compact size for tight spaces
• High quality internal seal
• Multi position handle

The complete fork upgrade kit - your choice of springs and Race Tech Gold Valves. Also includes a set of top quality fork seals and 5W fork oil to complete the job. Everything you need to transform your mushy stock forks into suspension that really works.

You can select from various straight rate springs to customize the package to your needs.

Stock Spring Rate for XR650L: 0.44 kg/mm

Lightweight, for reduced unsprung mass. Straight rate springs will give better control in the rough stuff. Sold in pairs.

• Rider and Gear up to 145 lb. = 0.47 springs → 24% stiffer than stock
• Rider and Gear 145-185 lb. = 0.52 springs → 39% stiffer than stock
• Rider and Gear 185-235 lb. = 0.58 springs → 56% stiffer than stock
• Rider and Gear 235-285 lb. = 0.63 springs → 66% stiffer than stock
• Rider and Gear 290 lb.-UP = 0.70 springs → 84% stiffer than stock

• Race Tech's original bolt-on fork valving system for front cartridge forks
• Triple the flow area of stock pistons
• Put valving control on the shim stack
• Outstanding tunability; improved control, traction, plushness and bottoming resistance
• Complete instructions, Gold Valve pistons, valving charts, valving shims and "Technical Edge
• Fork Maintenance and Gold Valve Installation" video all included

Bushings are dyno-tested to 500,000 strokes with less wear than OEM bushings

• Kit includes two slider bushings and two leg bushings
• Kit includes all copper washers and O-rings
• Kit includes two fork seal snap rings

Patented fork seal features a balanced 3 lip design that evenly distributes the pressure reducing operating temperature, wear and friction

Custom Elastomer Fork Seals have been tested to outlast OEM fork seals. Extends typical seal life by 3 to 5 times over OEM seals

Stiction (friction) measures from 1/3 to 1/2 less than OEM seals for smoother fork action

Lower Stiction, Longer Life! It doesn’t get any better than this!

Plus, the only complete line of dust wipers! Wipers should be replaced with the fork seals to assure peak performance. 

Kit includes Fork Seals and dust wipers.

 

An excellent replacement for the stock fork boots. These are great for protection from dirt, rocks and other contaminants. These boots utilize the latest advances in material technology to adapt to fork and styling demands. These high quality fork boots are 1/4 the price of the OEM factory replacements.

Fork brace precision machined from aluminum barstock. Drilled and tapped for optional lower fender attachment.

Hard anodized black for corrosion protection. Fits OEM forks. Split design allows for installing in minutes without having to remove the forks.

Helps protect vulnerable fork tube and seal from dust, dirt, and corrosive elements. Hook & loop (Velcro) fastening on back side makes installation or removal for cleaning a breeze.

Honda XR650L rear shock upgrade. The experts at Cogent Dynamics know suspension! A proven performance rear shock for your XR650L for use under the most demanding conditions and on the roughest terrain worldwide.

Damping rates optimized to your specific needs, giving you the best ride comfort, traction and control. Frequency and velocity sensing valving works great over wide ranging conditions. Low internal friction. All CNC machined components for top quality and performance. Compact and rigid design with internal separator piston. Adjustable for spring preload and rebound damping. Fully serviceable shock is designed for the long haul.

 *Spring color may vary due to specification requirement and availability.

A stiffer shock spring will help you get through the whoops or just help handle that extra baggage on the rear.

Stock spring rate is 10.5 KG/mm

*Spring color may vary due to specification requirement and availability.

Top suspension performance requires firm bottoming resistance with plushness at the same time. Even the best suspension tuners can only make the stock valving design work so well. The Gold Valve Shock Suspension System is a proven bolt-on shock valving system that improves control, traction, performance and bottoming resistance.

Complete kit to replace the bearings and seals in the XR650L shock linkage. Includes the lower shock bearing.

Heavy duty shock bumper. The stock bumper is prone to disintegrating with age. If you are re-valving your shock it's a good idea to be sure the bumper is in good shape.

Complete Pivot Works kit to replace the bearings and seals in the XR650L swingarm pivot.

Convenient kit eliminates looking up many part numbers.

Each kit contains bearings, pins, collars and seals manufactured to OEM specifications for a perfect fit.

Aluminum alloy lowering link. Lowers the rear suspension approximately 1 inch.

Bearings included.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

Kouba lowering link will lower the rear suspension 1.75". Comes with bearings and seals installed for a quick and easy installation.

Disclaimer: Lowering the front and/or rear of your motorcycle will change the geometry and may affect the handling, use caution after making changes/adjustments.

Based on the wildly popular Race Tech Suspension Seminars taught by Paul Thede around the world, this step-by-step guide shows riders how to make their bikes handle like the pros. Thede gives the lowdown on all types of suspension, including cartridge and non-cartridge forks as well as dual-chamber and nitrogen-charged shocks.

The three forces of suspension, testing procedures, even the black arts of chassis geometry: This explains it all. The book provides step-by-step photos of suspension disassembly and assembly as well as a detailed troubleshooting guide for dirt, street and track.

• Extracts dirt and debris trapped between fork seal and tube
• Easy way to keep fork seals clean and debris free
• Works on conventional and upside-down forks

Innovative design makes tool easier and more secure to use than old fashioned pin-aligned drivers

• Knurled anodized aluminum locking ring
• Perfectly weighted to drive seals
• Carbon steel body halves

Showa removed the schrader valve on many newer rear shocks. Now you need a needle to recharge your shock with nitrogen after a rebuild. Race Tech built this unit just for that job.

The features of this tool include 300 psi capacity, bleeder valve and T-handle plunger pin chuck. Swivel chuck has a 12" flexible hose. Comes complete with instructions, carrying box and Schrader valve extension (required on some Showa shocks). Nitrogen bottles available at any welding supply house.

The EVO R series draws on our rich heritage of making power. Offered for various off road MX and sport ATV models, the EVO R is a tried-and-true series that will save weight, add noticeable performance gains and sound tremendously better than stock.

• Hard anodized oval shaped aluminum muffler
• TIG welded reinforced muffler bracket(s)
• 304 stainless steel mid pipe / head pipe
• Red powder coated stainless steel end tip
• Lighter than stock exhaust system
• Huge horsepower and torque gains
• Sleek muffler design allows for maximum clearance
• Removable screen-type spark arrestor included
• Handmade in the USA
• 1 Year Limited Manufacturer’s Warranty