The DR650 is rather hard on the cush drive rubbers. Replace these any time you feel excessive play in the sprocket carrier hub. Excessively worn dampers can cause the cush hub bearing to fail - which will ruin your sprocket carrier. Sold as a set of 6 rubber dampers.
Make the installation as easy as possible with this Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight Circuit Board Upgrade making the connection simple. Stock plug will go right into this unit and off you go. You will need a crimp tool or set of needle nose pliers to crimp connectors on.
Make the Edge-2 installation as easy as possible with an Optional Connector Set. This allows you to put an OEM style connector on the Edge Taillight making the connection simple. Stock plug will go right into this unit and off you go. Will need a crimp tool or set of needle nose pliers to crimp connectors on.
Also works with Edge-2 Circuit Board Upgrade.
The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail / stop light function. 3 white LED's are used for license plate illumination.
Included is a set of turn signal brackets that bolt to the mount. These are designed for a smaller LED type signal with a 8mm mounting stud. Or consider the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!
The Edge-2 Tail Light and License Plate Holder is a simple bolt-on replacement for the stock unit. Included is an aluminum mount for the light and license plate that is model specific. The light unit uses 16 high-intensity red LED's for tail/stop light function. 3 white LED's are used for license plate illumination.
Included is a set of turn signal brackets that bolt to the mount, but these are designed for a smaller LED type signal with a mounting stud of just 8mm. If you think this might be a problem, look at the Edge-2 Upgrade Circuit Board as this converts your brake light into a functioning turn signal as well!
NOTE: LED's must be installed on a 12 V DC system!
You may have noticed after adding aftermarket turn signals (especially LED units) that your blink rate has significantly increased. OEM flashers are designed for standard bulbs which draw a few watts each, much more than typical aftermarket bulbs or LED signals. This device is an effective alternative to using load resistors because it consumes considerably less watts, consumes less space, and does not generate excessive heat.
The plug is exactly the same as the OEM unit making swap outs a cinch. No wiring changes, cutting and adding connectors. Just plug it in and you will have a steady flash at the DOT OEM rate regardless of what signal bulbs you use. It is an all solid state design and will blink correctly with loads all the way down to 0.1W / 0.01A.
Not for any DRZ400 or Royal Enfield Himalayan
The OEM foam secondary filter can deteriorate rather quickly. Once that happens, it can allow enough dirt into the engine to do significant damage. Replace your filter now with a high-quality foam filter from industry leader Twin Air.
This filter needs to be oiled like any air filter to work properly.
Only for bikes with the stock BST40 carburetor!
The OEM vent foam filter can deteriorate after only a couple of years. When it does it can allow enough dirt into the engine to do significant damage. Replace your filter now with a washable cotton & steel screen filter.
This filter is recommended to be oiled like any other air filter to work properly.
Only for bikes with the stock BST40 carburetor!
Genuine KTM replacement air filter. Replace your air filter at recommended service intervals.
R&D introduces "Flex-Jet", a simple, effective flexible shaft design. Quick adjustments are now within easy reach. Besides easy access, another benefit is the Flex-Jet's ability to hold its setting. Loose fuel screws are now a thing of the past. Kit includes: Flex-Jet (Remote Fuel Screw), bracket, screw, spring, washer, O-ring and instructions.
Not for the stock DR650 carburetor Fits FCR-MX conversions Only.
Top quality brass screw with molded knob for easy adjustments.
Not for the stock DR650 carburetor Fits FCR-MX conversions Only.
Contains genuine KEIHIN parts to rebuild your FCR41 pumper. Fresh o-rings and float needle insure you don't end up with a crank case full of fuel.
Not for the stock carburetor. Fits FCR41 conversions only.
This brass fuel screw offers a longer head to give you a better hold for making adjustments. This is a nice improvement over the standard extended fuel screw. Kit includes one new screw, spring, washer and o-ring.
Direct replacement for the stock spring and exactly like the old Merge Racing spring. Gives a much more consistent accelerator pump squirt. Eliminates the need for the 'O-ring mod', wire or zip-ties on the pump arm. Fits all Keihin FCR-MX carbs except '07-'08 CRF250/450.
Not for the stock DR650 carburetor Fits FCR-MX conversion Only
This cover acts as an "adjustable leak jet" to fine tune the accelerator pump squirt.
Eliminates "4-stroke bog" when used with correct jetting. Allows the use of correct carburetor settings to optimize performance, starting and reliability. Improved low-end performance with much better throttle response. Investment cast and finished to precise tolerances with internal high volume vertical check valve. Fits all motorcycles and ATVs using a Keihin FCR carburetor Easy installation instructions (including online video) and template.
Not for the stock DR650 carburetor Fits FCR-MX conversions Only.
Designed for use with stock engines using either stock or aftermarket exhaust and air filters.
The map selection switch allows the rider to switch between two different maps "on the fly" within the Power Commander V.
Don't have a dyno tuning center nearby? Are you more of a do it yourself type? Are you constantly changing parts on your bike?
If you answer "yes" to any or all of the questions above, then our Auto Tune kit is for you. The Dynojet Auto Tune kit is an "add on" accessory that can be used with any of the Power Commander Vs
It connects to the PCV with a single cable and requires only a ground and +12 volt connection to be made to install. If your exhaust does not already have one, a "weld in" O2 sensor bung is included
Once installed, the Auto Tune kit monitors the fuel mixture (by installing the included Wide Band O2 sensor in the exhaust). It then sends this information to the Power Commander V and automatically corrects it while you ride. Each map that we offer has preset Air/Fuel ratio values included that we find to be the best overall settings. This lets you simply plug in the unit and let it do the work.
Spare replacement throttle cables for your TM40 carburetor conversion. Fits the stock throttle housing.
These are premium low-friction cables.
A quality replacement speedometer cable
Mount these polished billet aluminum spacers under your handlebar clamps to raise your handlebars 1 inch. High quality longer bolts are included.
Forged aluminum, black anodized arm and Knurled CNC aluminum shift tip.
This bracket mounts between the frame and your right footpeg bracket (works with both stock and low mounts) and allows you to adjust the slop out of the stock system. Puts the pedal in the ultimate location for immediate brake activation and eliminates unwanted pedal motion. Kit includes plate, adjuster bolt and lock nut and instructions.
These 7/8" bars fit in the stock clamps and raise your grips a couple inches. They look great too!
| Width | Height | Rise |
| 813mm | 160mm | 104mm |
| Clamp Area | Sweep | Control Area |
| 236mm | 100mm | 199mm |
Comfortable Oversize (or Fat Bar) Handlebars.
For bikes with factory 7/8" handlebars these will require the use of a 7/8 to 1-1/8 adapter (sold separate).
Ease the pressure on your wrist during those long highway trips.
ProCycle has developed this unique kit to work with your OEM bars and controls. Just flip the thumb lever down to apply enough friction to hold the throttle in place.
Customize the power characteristics of your bike by simply adding an altered ration cam. The Control cam allows smoother more controlled throttle while the Quick cam lets you put the power to the ground quickly.
Throttle Lock Kit Includes:
Special tool to remove the flywheel from the end of the crankshaft.
+2mm oversize from stock.
Requires cylinder boring only. Bore Diameter: 83mm, Piston Diameter: 82.95 mm
12.5:1 compression. Includes pistons, rings, pins, clips and head gaskets.
All Wiseco Pistons are forged from high silicon, low expansion aluminum which offers superior strength, reduced weight, improved heat transfer, and longer life.
Diamond turned finish from one of the many CNC computer controlled turning centers guarantees you a perfect finish with no size variation. Wiseco pistons can be installed in any of today’s cylinder bore compositions (cast iron, chrome, nikasil and boron)
Wiseco’s wide range of oversize pistons increase the life of cast iron lined cylinders.
Wiseco’s state-of-the-art computerized manufacturing facility is dedicated to supplying both the high-perfomance racer and recreational enthusiast with the finest forged piston available in today’s market place.
Fresh O-rings to ensure your XRL stays oil-tight and leak free. The Valve Cover Kit includes 4 new valve cover O-rings.
Fresh O-rings to ensure your XRL stays oil-tight and leak free. The Oil Change O-Ring kit includes a filter cover O-ring and a filler plug O-ring.
Superior Filtration:
This should be the last oil filter you will ever buy. Made from laser cut, medical grade, 304 stainless steel micronic filter cloth, this filter provides 200% more filter area in many cases. Most good paper filters will pass particles in the 90 to 95 micron range, and some tested, as much as 300 microns. Sand is about 125 microns and a white blood cell approximately 25 microns. Scott's stainless filter catches items down to 35 microns "absolute", which is about 3 times better than most good paper or brass filters. The pleat seam is welded, able to withstand up to 600 degrees in our filter, not glued, like paper filters.
Providing unbeatable performance and exceptional value, Hiflofiltro is the best-selling brand of aftermarket filters for motorcycles, scooters, and ATVs worldwide. The filters are also supplied to original equipment manufacturers as well as private label brands.
Grab our 5-pack and save both time and money!
Fresh o-rings to ensure your DR650 stays oil-tight and leak free. Includes one of each: oil filter o-ring, filter cover o-ring and filler cap o-ring
Barnett high performance clutch kit includes drive plates, carbon fiber friction plates, and heavy duty springs.
Here we have right side plate that bolts to our ProCycle Side Racks for mounting your RotoPax fuel or water containers.
Limited quantity available for right side only.
Wide Adventure rack for the WR. Precision laser cut from .25" 5052 aluminum then powder coated black with a shot peened look. This rack is 11" x 17.5" and has numerous tie points for straps or bungees to secure a load. It is pre-drilled for a RotopaX mount. Easy installation means it is bolted to the bike in 10 minutes. There is some minor drilling of the plastic to be done. All necessary hardware and complete instructions included.
The ProCycle rack system is designed and manufactured by dual sport riders that know what it takes to create a durable and versatile luggage rack.
Our racks allow for easy installation of both soft and hard luggage.
See the linked instructions for how-to videos.
Steel cargo rack from Moose Racing. It features a nice wide platform and a durable powder coat finish. 17" wide and 10" long.
An optional add on to your ProCycle Top Rack to relocate your rear turn signals with ease.
Each kit includes all necessary rubber components and brake pins.
All the parts you need to freshen up your front brake caliper. New piston seals, slide pin and boots. Fix that sticky or limp front brake.
All the parts you need to freshen up your rear brake caliper. New piston seals, slide pin and boots. Fix that sticky or limp rear brake.
Genuine Yamaha caliper rebuild parts will get your front disk brake back in shape.
Galfer Steel Braided lines have a Teflon tube core and are wrapped with a stainless steel wire braided exterior that prevents expansion under pressure.
The benefit is a firmer brake lever with better feel because the energy that was going into expanding the stock lines now goes straight to the brake pads.
All the parts you need to freshen up your rear brake master cylinder. New piston, seals, return spring, boot and snap ring.
Genuine Yamaha rebuild kit for leaking or damaged front disk brake master cylinders.
Semi-sintered construction contains 30% copper by weight within and organic matrix
This design combines the long life of a sintered pad with less rotor wear common with sintered pads
Includes pads for both front rotors.
These awesome rotors are laser-cut out of a high-carbon content 410 stainless steel, lap cross hatch ground, and heat-treated. The finished rotors are mounted on a floating black steel carrier for durability and strength.
The floating pins are an oversized CNC machined stainless rivet with stainless wave washer to ensure these rivets will not crush like more traditionally used steel pressed rivets. high temp paint is applied to surfaces like cooling holes and edges to provide a clean finished look.
Includes a fresh set of brake rotor bolts.
Don't cut the ball ends off of your levers! These billet spacers move your hand guards outward to allow clearance for the full length of the stock levers. Designed to fit steel or aluminum bars. Includes longer stainless steel mounting bolts.
Developed for the DR650 but may work on other models with long levers. (May require additional adjustment or modification on some models.)
Not compatible with Acerbis and Emgo hand guards
Constructed of durable 3mm powder coated aluminum and easily installed utilizing existing mounts, the R&G Bash Plate (center plate) will protect the underside of your motorcycle from damage and debris. Add Case Guards (left and right plates) to your order for complete protection.
B&B Engineering Bash Plate for the CRF250L is made from 5083 4mm aluminum plate. Chosen because of its suitability for welding and extreme abrasion and impact resistance, this plate will protect the valuable center cases and deflect items away from the side cases as well. This plate is supplied with the necessary stainless clamps and bolts where necessary as well as foam or rubber where required.
Constructed of heavy-duty machined steel, aluminum, and high-density nylon, R&G frame sliders provide maximum protection and high quality fit and finish. R&G "Aero" sliders have an aerodynamic teardrop shape for a more streamlined look than traditional cylindrical slider pucks
R&G "Cotton" Reel Swingarm Spools are oversize paddock stand bobbins that perform double duty as lifting points for hook style paddock stands as well as protection for the swingarm of your motorcycle in the event of crash or drop.
Developed on the track and brought to the road. R&G engine case covers are made from 4mm polypropylene for strength, durability and looks that compliment your bike. Both sides included.
High grade aluminum alloy front disk guard is the ultimate in front disc protection!
These hand-built units out of Australia are one of the most advanced radiator protection systems available! CNC machined 6000 series three-dimensional aluminium extrusion melded with 5000 series alloy plate to create a system that protects your precious radiator from almost any direction.
Designed with a fin angle that allows almost nothing to come in contact with the vulnerable core that is otherwise directly exposed to roost, rocks and all sorts of trailside debris. The fins are designed in a fashion that they completely mimic the designed airflow characteristics of the OEM plastic protector fins.
The protective finned louver panel quickly and easily unbolts to make clean-up a snap. Three-piece modular construction allows for greater design flexibility which eliminates the compromises that are built into one-piece designs. If any single piece of this unit is ever damaged, it is replaceable by itself, no need to replace the entire guard. Just give us a call. Installation is a snap, taking no more than 30 minutes with basic tools.
One of the most advanced radiator protection systems available for the DRZ400. These guards feature maximum side and front impact protection by using a combination of CNC machined 6000 series aluminum and 5000 series alloy plate to create a complete system to protect your radiators from virtually every direction. Roost and debris protection is exceptional thanks to the angle fin design that leaves minimal exposure to the radiator core and veins.
Even with all of this protection, cooling airflow is still at its maximum with a front louvered panel built with fins designed to mimic the airflow characteristics of the OEM plastic fins. This panel can be removed easily facilitating cleaning of the radiator.
Three-piece modular construction eliminates the design limitations of one-piece designs. Integrated modular construction- Three piece modular construction allows for greater design flexibility eliminating the compromises inherent with one piece designs. Easy fitment no mods required- Radiator guards can be fitted in approx ½ hour using basic tools. Sold in pairs, but repair parts are available individually.
Can be fitted with 17L safari tank & Acerbis tank
Will not fit the "S" & "SM" model if thermo fan is fitted
Top suspension performance requires firm bottoming resistance with plushness at the same time. Even the best suspension tuners can only make the stock valving design work so well. The Gold Valve Shock Suspension System is a proven bolt-on shock valving system that improves control, traction, performance and bottoming resistance.
By simply replacing a motorcycle's stock shock linkage with with a longer, stronger and lighter DeVol Lowering Linkage, a bike's seat height will be dramatically lower to help give those riders with shorter inseams a more confident and enjoyable ride.
Complete high quality kit to replace the bearings and seals in the swingarm pivot.
Complete high quality kit to replace the bearings and seals in the KLX shock linkage. Includes the lower shock bearing.
| Kit Contents: | |
|---|---|
| Washer | 4 |
| Seal | 8 |
| Needle Bearing Shaft | 4 |
| Needle Bearing | 7 |
Damping Rod style forks are notorious for being too harsh, too mushy and too easy to bottom. Gold Valve Cartridge Emulators remedy this problem by controlling the compression damping with a tuneable valve. The Emulator sits on top of the damping rod and is held in place by the main spring.
Simply put; Emulators make damping rod forks perform like well-tuned cartridge forks. Installation and tuning for any condition or rider preference is very straight-forward.
Simple to install and completely tunable for all conditions and rider preferences.
Shorai batteries deliver more energy faster, with less weight and with less wear on the battery per start cycle than any other brand or technology available on the market today.
Specifications:
Weight (lbs): 2.30 lbs
Weight (kg): 1.04 kg
Cold Cranking Amps: 270
A/HR: 18
Polarity: [+ -]
A HIGH output performance stator that replaces the OEM stator in the Honda XR400R and XR650R models.
ElectroSport designed this to have two sets of output windings: one is floated from ground and has two output leads, and the other is grounded on one side. Both windings also have different winding configurations to ensure optimum output.
Built on a modern stator core made of highly magnetically conductive material. They install the highest grade copper wire using their state-of-the-art computer controlled winding machines and they connect high quality lead wires that are both abrasion and heat resistant.
This stator comes with high grade rubber seals and connectors installed and as such is a plug in replacement.
Even if you don't need the extra lighting or charging output you can still use it as a straight replacement for the OEM stator and it is a very cost effective solution that way.
Warp 9 Supermoto wheels are built with billet hubs, 7000 series aluminum rims and laced and trued with stainless steel spokes and nipples.
Add tires to your wheel order and we will throw in tubes and mount and balance them at no additional charge.
The set includes a 24mm for the rear and a 19mm for the front. Each 10 inch forged steel tire iron has a hex wrench on one end. The rounded spoon end minimizes pinched tubes and scarred rims.
A kit that includes an Axle Wrench combo for your bike with a 19mm for the front, and a 24mm for the rear. Just 7 1/2" long, it is long on leverage, but short enough to fit in even the smallest tool kit.
Also includes a pair of 'trail size' small tire irons.
The set includes a 19mm and a 22mm to hold the axle and nut both front and rear. Each 10 inch forged steel tire iron has a hex wrench on one end. The rounded spoon end minimizes pinched tubes and scarred rims.
This tool is designed to separate vertically split crank case halves on two and four stroke engines. Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included.
Repair manual for XR250R '86-'04 / XR250L '91-'96 / XR400R '96-'04.
ThreeBond 1342 low strength thread locking compound. This is the ideal retaining compound for small nuts and bolts. Fasteners are held securely but, can be easily removed when necessary. ThreeBond gives this a number 4 rating for exposure to engine oil making it a good choice for internal fasteners as well as external fasteners. 10ml bottle.
The Phillips type screws used in Japanese motorcycles are actually Japanese Industrial Standard (JIS) screws are very easy to strip if you are using a regular Phillips screwdriver.
This is a high quality Motion Pro T-handle driver with #1, #2, and #3 JIS bits made from S2 tool steel. There is bit in each end of the driver held in place magnetically. These are 1/4" hex drive heads so you can use all common driver bits as well. The narrow drive head profile easily fits into tight locations. Main shaft is 8.5" long and is chrome plated for protection.
A set of three OEM Suzuki front sprocket bolts. Thread-lock compound has already been applied for extra security.
Savvy DR650 owners will remove the upper chain roller. You can use this stainless steel button head screw to plug the threaded hole. Suzuki did not make the upper roller mount strong enough. If you don't remove it yourself the chain will likely do it for you - along with a chunk of metal out of the frame.
Wind noise alone on a motorcycle can produce noise levels up to 95db. Permanent hearing damage can occur from 85db, so it is essential to always use hearing protection.
NoNoise Hearing Protectors are superior to traditional foam, wax or silicone earplugs. Precision-tuned, patented ceramic filters ensure maximum protection from dangerous levels of engine, wind and road noise. Unique filtration allows conversation, sirens and horns to remain clearly audible, with no muffled effect. Comfortable and suitable for all ages, they are ideal for bikers and other motor sport enthusiasts. Included is an aluminum tube with a sealed threaded cap for storage. A key ring on the cap allows for attachment of the tube to you jacket, gloves or tank back for easy access.
These units are made from Silicone-free, hypoallergenic thermoplastic for the ultimate in comfort. Another benefit is that this material can be washed and re-used.
This chain lube comes in a squeeze-tube bottle with an integrated brush nozzle. It makes applying chain lube easy and less messy than spray on lubes.
Better throttle response. More power over a much wider range.
Kit includes pre-jetted genuine Mikuni TM36 Pumper carb and push/pull throttle cables. Everything is included to mount this carb to your bike. Well suited for stock to mildly modified motors.
Low peg mounts for the DR From Wirtz Wire. These are different than our other mounts for several reasons. First, these are designed around the stock pegs. All of the pegs in this section will fit these mounts. Another difference is that these mounts are offered in a low mount as well as a low and rearward mount. These are 'wire EDM' machined from solid 1018 steel bar stock, and are not welded anywhere. They are powder coated black for a great look. Both mounts move the pegs down 2" while the low and rear mounts also move the pegs back 1.3".
Kit comes with new mounts, longer bolts and a longer brake switch spring that will be needed. Pegs are optional, your stock pegs will work.
The upper image shows the low and rearward mounts while the one below that is of the just low mounts. If you look at the two images below that, you will see that these are the low and rearward pegs for both sides of the bike.
Pivot Pegz have set a new standard in footpeg performance and quality and now they are even better. The new Mark 4 Pivot Pegz are wider & stronger. They have a unique multi-directional grip pattern and a wide, open design to reduce mud packing. The Mark 4 also incorporates new heavy duty, long life springs and they come with a lifetime warranty.
Pivot Pegz aim is to build the best footpegs in the world and they really do perform as good as they look. Here's a bonus for those riders with size 13 boots - the pivoting action of these pegs makes it easier to get your toe under the shift lever.
Have you already ditched the bulky tail light on your XR? Don't want to bend your license plate and wrap it around your rear fender? Here is a great solution to clean up the looks of the backside of your XR650L. If you haven't already upgraded to the smaller and better looking WPS Tail light, select 'Bracket & Light' from the menu and you will get the WPS Taillight AND the License Plate Holder.
Please note that this no longer has a window for a license plate light. To stay legal, you can mount one or two License Plate Lights to your plate holder, or you can check out the LED License Plate Frame.
Don't like the low fender on your TW200? The ProCycle High Mount Fender Bracket allows you to mount your fender under the lower triple clamp to create more clearance around your front wheel and drastically improve the look of your T-Dub.
The kit is made of high-quality steel components manufactured in the USA, and includes the bracket and all required hardware.
| 4 | 8x40 Bolt |
| 4 | 6x20 Bolt |
| 6 | 6x16 Washer |
| 4 | 6mm Nyloc Nut |
| 2 | Spacer |
Don't forget to add a new fender for that supermoto look!
Contour rotors are ultra lightweight OEM replacement rotors made with tough and durable stainless steel. Heat treated to perfection and then diamond ground to micron accurate surface finish and parallelism and will deliver great brakes that will perform and last.
Front Rotor, Limited stock
Here's the Moose Racing seat for you XR650L riders. This is a complete seat that's installed on a new seat pan. Take your old seat off and put your new seat on and get back to riding! The durable micro-fiber suede top cover enhances rider comfort and increases stability. Side gripper panels ensure secure seating during aggressive maneuvers. The cover is constructed from smooth marine-grade vinyl and features an embossed Moose Racing logo. It includes a strap kit that enables secure attachment of cargo to the pillion section of the seat.
Corbin seats are carefully designed to provide a comfortable riding position. They are firm and supportive which allows you to ride all day without fatigue unlike the stock seat. Comfort Cell Foam retains resilience and doesn't crush down like the stock seat foam. On the top, Corbin covers are only the highest grade of weather resistant materials for durability and long life. Corbin seats install the same as stock with two bolts into the chassis which provides a closer fit to the bodywork and tank.
Seat Concepts seats are constructed using a foam material that is a much higher quality than OEM seat foam. Their proprietary formula provides a more plush and active ride, while still offering the necessary amount of support. Their unique comfort shape maintains a similar contour to stock at the front of the seat so the rider’s legs are not spread farther apart, but tapers out towards the mid-point to distribute rider weight over a greater area.
These features combine to offer a custom seat feel, and provide greater enjoyment and increased range on a long commute, or adventure ride!
Check out the seat warmer we carry. Put this in before tacking your cover in place and keep yourself warm during even the coldest rides. Nothing like toasted buns to make a ride comfortable!
Fits Models/Years:
2004-2007 950 Adv.
2008-2013 990 Adv.
2009-2011 990 Adv. R
2013 990 Adv. Baja
The Foam and Cover Kit is only for the OEM pan. It DOES NOT include the pan.
| Width: | 13" (330mm) |
| Height: | 3/8" (10mm) Lower than stock |
The PowerBomb header promotes better flow by allowing a small expansion of the exhaust gasses. The 'bomb' also acts as a pre-muffler taking the edge off of overall sound levels.
Optional Heat Shield Strip will protect your airbox from the close proximity of the hot head pipe.
These gaskets seal the joint between the head pipe and Exhaust port. They are designed to crush a little bit to tightly seal where the pipe fits to the head. Get a fresh one now avoid having an exhaust leak when you install your new exhaust. Sold as a set of 2.
OEM Suzuki seal retainer for the DR650. Simple insurance against your countershaft seal popping out of its bore.
This is not a common problem but for those folks who have had the seal come out it has proven to be quite difficult to get it to stay in place. This steel retainer eliminates any possibility of the seal coming out and ruining your day by coating your rear tire with oil.
The chain slider protects the swingarm from contact with the chain. Replace yours before it wears through to the swingarm.
These quality JT sprockets are made from the finest 545C high carbon steel and are then heat treated and hand finished to meet or exceed OEM standards. Outlasts many mild steel or surface hardened sprockets as much as two and three times over.
This nice piece replaces your plastic sprocket cover and protects your engine case from a chain derailment or failure. The 3/16" (5mm) thick steel plate is adjustable to accommodate 14, 15 and 16 tooth sprockets. Includes mounting hardware.
The Voyager Pro GPS is designed for off-road and adventure-riding enthusiasts. The GPS delivers robust features that cater specifically to the needs of riders in rugged and challenging environments. The device integrates with your vehicle, and our patented buddy tracking feature ensures the best-connected experience, whether off-road or on-road. The Voyager Pro is perfect for any adventure. Get yours today!
Key Features of the Trail Tech Voyager Pro:
Summary:
Trail Tech’s Voyager Pro is a comprehensive GPS solution for all adventure-seeking riders. It is specially designed for off-road harsh, rugged conditions and offers a blend of navigation and buddy tracking with vehicle monitoring features. It is the best rugged GPS on the market.
This is the evolution of taking the proven GPRV1 steering damper and locating it under the handlebars. Mounting the damper unit under the bars allows for addition room on the top cross-bar or bar mounts.
This GPR setup is a good choice for the weekend warrior to the race professional that would like to raise the handlebar height. Perfect for desert and off-road GPs.
Make it easy to pull the rear axle out of your V-Strom. This little handle goes into the hollow axle and then tightens down to give you a handle so you don't have to tap it out from the other side.
